Cisco ASA IPsec encrypt selective traffic between peers
Hello i have aproximately this topology:
192.168.13.0/24 ----> ASA1 (Public IP 10.1.1.2) ---> ISP1 <----> ISP2 --->ASA2 (Public IP 10.1.2.2) ---->192.168.4.0/24
Both ASA are 55xx
I've setup IPsec site-to-site vpn between these two ASA and now the net 192.168.13.0/24 is able to access the net 192.168.4.0 and vice versa.
Now, I want to access the ASA2 with via SNMP from 192.168.13.0 but it seems that ISP1 or ISP2 blocks UDP port 161 ...
Now my question:
can I encrypt the traffic between 192.168.13.0/24 and 10.1.2.2 ?
I tried to add NAT and VPN ACL an entries like this:
ASA1:
permit from net 192.168.13.0/24 to host 10.1.2.2
no nat from net 192.168.13.0/24 to host 10.1.2.2
ASA2:
permit from host 10.1.2.2 to net 192.168.13.0/24
After this setup I watch in ASDM / monitoring / VPN Session Details:
ASA1
Local Addr: 192.168.13.0/24
RemoteAddr: 10.1.2.2
Bytes TX: 46036
Bytes RX: 0
ASA2
Local Addr: 10.1.2.2
RemoteAddr: 192.168.13.0/24
Bytes TX: 0
Bytes RX: 45144
From log debugging I watch that the ICMP and SNMP packets from 192.168.13.0/24 arive to 10.1.2.2, but it seems that ASA2 doesn't repply... Any idea ?
ASA2 config:
route ISP2 192.168.13.0 255.255.255.0 10.1.1.2
crypto ipsec ikev1 transform-set FirstSet esp-3des esp-md5-hmac
access-list ISP2_cryptomap line 1 extended permit ip 192.168.4.0 255.255.255.0 192.168.13.0 255.255.255.0
access-list ISP2_cryptomap line 1 extended permit ip host 10.1.2.2 192.168.13.0 255.255.255.0
crypto map ISP2_map4 1 match address ISP2_cryptomap
crypto map ISP2_map4 1 set peer 10.1.1.2
crypto map ISP2_map4 1 set ikev1 transform-set FirstSet
crypto map ISP2_map4 1 set security-association lifetime seconds 86400
crypto map ISP2_map4 interface ISP2
crypto ikev1 enable ISP2
crypto ikev1 am-disable
crypto ikev1 policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
tunnel-group 10.1.1.2 type ipsec-l2l
tunnel-group 10.1.1.2 ipsec-attributes
ikev1 pre-shared-key *****
ASA1 Config:
route ISP1 10.1.2.2 255.255.255.255 10.1.1.1
access-list ISP1_cryptomap line 1 extended permit ip 192.168.13.0 255.255.255.0 192.168.4.0 255.255.255.0
access-list ISP1_cryptomap line 1 extended permit ip 192.168.13.0 255.255.255.0 host 5.56.103.111
crypto ipsec ikev1 transform-set FirstSet esp-3des esp-md5-hmac
crypto map ISP1_map4 1 match address ISP1_cryptomap
crypto map ISP1_map4 1 set peer 10.1.2.2
crypto map ISP1_map4 1 set ikev1 transform-set FirstSet
crypto map ISP1_map4 1 set security-association lifetime seconds 86400
crypto map ISP1_map4 interface ISP1
crypto ikev1 enable ISP1
crypto ikev1 am-disable
crypto ikev1 policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
tunnel-group 10.1.2.2 type ipsec-l2l
tunnel-group 10.1.2.2 ipsec-attributes
ikev1 pre-shared-key *****
LAN behind ASA is 192.168.50.0/24, but i need have comunication between
192.168.211.0/24 and 192.168.212.0/24
I have ACL in both direction because i need initialize connection from both sides:
192.168.211.0/24 <-> 192.168.212.0/24
i have both acl becasue i have two peers:
crypto map SDM_CMAP_1 211 match address test-p1-p2
crypto map SDM_CMAP_1 211 set peer 8.8.8.8
crypto map SDM_CMAP_1 212 match address test-p2-p1
crypto map SDM_CMAP_1 212 set peer 8.8.4.4
i removed :
route outside 192.168.211.0 255.255.255.0 194.146.123.1 1
but it didn't help
packet-tracer input outside icmp 192.168.211.1 0 3 192.168.212.1
Phase: 8
Type: VPN
Subtype: encrypt
Result: DROP
Config:
Additional Information:
Forward Flow based lookup yields rule:
out id=0xd83fd240, priority=70, domain=encrypt, deny=false
hits=81, user_data=0x0, cs_id=0xd7b688c8, reverse, flags=0x0, protocol=0
src ip=192.168.211.0, mask=255.255.255.0, port=0
dst ip=192.168.212.0, mask=255.255.255.0, port=0, dscp=0x0
Similar Messages
-
Cisco ASA - Pass Through QoS Traffic
Hi Sirs,
Given the following topology:
Switch - IP Phone (Branch) |----| Router |----| MPLS |----| Router |----| ASA |----| Switch - Voice Network (Head Office)
My question, the ASA can impact the QoS traffic to pass through it?
Thank you!
Rafael TrujilhoHi Andrew,
I want the ASA does NOT take any markings, NOT impacting the quality applied to voice traffic.
Regards,
Trujilho -
Cisco ASA 5520 traffic between interfaces
Hello,
I am new in the Cisco world , learning how everything goes. I have a Cisco ASA 5520 firewall that i am trying to configure, but i am stumped. Traffic does not pass trough interfaces ( i tried ping ) , although packet tracer shows everything as ok. I have attached the running config and the packet tracer. The ip's i am using in the tracer are actual hosts.
ciscoasa# ping esx_management 192.168.10.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.10.100, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
ciscoasa# ping home_network 192.168.10.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.10.100, timeout is 2 seconds:
Success rate is 0 percent (0/5)
Thank you in advance.Hi,
Is this just a testing setup? I would suggest changing "internet" interface to "security-level 0" (just for the sake of identifying its an external interface) and not allowing all traffic from there.
I am not sure what your "packet-tracer" is testing. If you wanted to test ICMP Echo it would be
packet-tracer input home_network icmp 10.192.5.5 8 0 255 192.168.10.100
I see that you have not configured any NAT on the ASA unit. In the newer ASA software that would atleast allow communication between all interface with their real IP addresses.
I am not so sure about the older ASA versions anymore. To my understanding the "no nat-control" is default setting in your model which basically states that there is no need for NAT configurations between the interfaces the packet is going through.
Have you confirmed that all the hosts/servers have the correct default gateway/network mask configurations so that traffic will flow correctly outside their own network?
Have you confirmed that there are no firewall software on the actual server/host that might be blocking this ICMP traffic from other networks?
Naturally if wanted to try some NAT configurations you could try either of these for example just for the sake of testing
Static Identity NAT
static (home_network,esx_management) 192.168.5.0 192.168.5.0 mask 255.255.255.0
static (home_network,DMZ) 192.168.5.0 192.168.5.0 mask 255.255.255.0
static (home_network,management) 192.168.5.0 192.168.5.0 mask 255.255.255.0
OR
NAT0
access-list HOMENETWORK-NAT0 remark NAT0 to all local networks
access-list HOMENETWORK-NAT0 permit ip 192.168.5.0 255.255.255.255.0 192.168.10.0 255.255.255.0
access-list HOMENETWORK-NAT0 permit ip 192.168.5.0 255.255.255.255.0 192.168.20.0 255.255.255.0
access-list HOMENETWORK-NAT0 permit ip 192.168.5.0 255.255.255.255.0 192.168.1.0 255.255.255.0
nat (home_network) 0 access-list HOMENETWORK-NAT0
Hope this helps
- Jouni -
Cisco ASA not returning traffic when wccp peering with Bluecoat.
Experts,
My setup has a Cisco ASA where we are doing wccp with a Bluecoat SG box. The traffic gets redirected to the Bluecoat due to the wccp settings so it's just transparent to the end users. Theye do not have to do any manual proxy settings in their IE.
We however notice that somehow the ASA does not return these connection back to the requesting hosts and somehere the connection table breaks. The message we see on the ASA that state table is somehow not being maintained. Any idea where this connection must be breaking?
Regards,
Nikhil Kulkarni.Nikhil,
Let me give you a little bit of backgrounf in regards to WCCP that can help you. As you stated the ASA will do transparent redirection, so the client doesn't have to configure anything on the PC.
The traffic will get to the ASA (port 80/443 or any configured port) and then the ASA will establish a GRE tunnel with WCCP server and will redirect the traffic. After the Bluecoat receives the traffic it will "spoof" the IP address of the requested web page (the WCCP server needs to have direct comunication with the client PC without passing through the ASA). I have seen some issues where the ASA and the WCCP server are unable to establish the GRE tunnel becuase the ASA uses the highest IP address as the router ID and uses this IP address to establish the tunnel. The WCCP keepalives (Here I am, I see you) are sent using the IP address of the closest IP address to the WCCP server.
At this point you may turn on the WCCP debugs and run some "show WCCP" commands.
I hope it helps
Luis Silva -
Site-to-Site VPN between Cisco ASA 5505 (8.4) and Cisco Router (IOS 15.2)
Hi, I'm trying to create Site-to-Site VPN between Cisco ASA 5505 and Cisco Router 3945.
I've tried create configuration with and without ASA wizard, but anyway it doesn't work.
Please help me to find where is the issue.
I have two sites and would like to get access from 192.168.83.0 to 192.168.17.0
192.168.17.0 --- S1.S1.S1.S1 (IOS Router) ==================== S2.S2.S2.S2 (ASA 5505) --- 192.168.83.0
Here is my current configuration.
Thanks for your help.
IOS Configuration
version 15.2
crypto isakmp policy 1
encr aes 256
authentication pre-share
group 2
crypto isakmp key cisco address 198.0.183.225
crypto isakmp invalid-spi-recovery
crypto ipsec transform-set AES-SET esp-aes esp-sha-hmac
mode transport
crypto map static-map 1 ipsec-isakmp
set peer S2.S2.S2.S2
set transform-set AES-SET
set pfs group2
match address 100
interface GigabitEthernet0/0
ip address S1.S1.S1.S1 255.255.255.240
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
crypto map static-map
interface GigabitEthernet0/1
ip address 192.168.17.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
access-list 100 permit ip 192.168.17.0 0.0.0.255 192.168.83.0 0.0.0.255
ASA Configuration
ASA Version 8.4(3)
interface Ethernet0/0
switchport access vlan 2
interface Vlan1
nameif inside
security-level 100
ip address 192.168.83.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address S2.S2.S2.S2 255.255.255.248
ftp mode passive
same-security-traffic permit intra-interface
object network inside-network
subnet 192.168.83.0 255.255.255.0
object network datacenter
host S1.S1.S1.S1
object network datacenter-network
subnet 192.168.17.0 255.255.255.0
object network NETWORK_OBJ_192.168.83.0_24
subnet 192.168.83.0 255.255.255.0
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended deny ip any any log
access-list outside_cryptomap extended permit ip 192.168.83.0 255.255.255.0 object datacenter-network
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpn_pool 192.168.83.200-192.168.83.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic inside-network interface
nat (inside,outside) source static inside-network inside-network destination static inside-network inside-network no-proxy-arp route-lookup
nat (inside,outside) source static inside-network inside-network destination static datacenter-network datacenter-network no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.83.0_24 NETWORK_OBJ_192.168.83.0_24 destination static datacenter-network pdatacenter-network no-proxy-arp route-lookup
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 DEFAULT_GATEWAY 1
crypto ipsec ikev1 transform-set vpn-transform-set esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set vpn-transform-set mode transport
crypto ipsec ikev1 transform-set L2L_SET esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set L2L_SET mode transport
crypto dynamic-map dyno 10 set ikev1 transform-set vpn-transform-set
crypto map vpn 1 match address outside_cryptomap
crypto map vpn 1 set pfs
crypto map vpn 1 set peer S1.S1.S1.S1
crypto map vpn 1 set ikev1 transform-set L2L_SET
crypto map vpn 20 ipsec-isakmp dynamic dyno
crypto map vpn interface outside
crypto isakmp nat-traversal 3600
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
group-policy GroupPolicy_S1.S1.S1.S1 internal
group-policy GroupPolicy_S1.S1.S1.S1 attributes
vpn-tunnel-protocol ikev1
group-policy remote_vpn_policy internal
group-policy remote_vpn_policy attributes
vpn-tunnel-protocol ikev1 l2tp-ipsec
username artem password 8xs7XK3To4s5WfTvtKAutA== nt-encrypted
username admin password rqiFSVJFung3fvFZ encrypted privilege 15
tunnel-group DefaultRAGroup general-attributes
address-pool vpn_pool
default-group-policy remote_vpn_policy
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group S1.S1.S1.S1 type ipsec-l2l
tunnel-group S1.S1.S1.S1 general-attributes
default-group-policy GroupPolicy_S1.S1.S1.S1
tunnel-group S1.S1.S1.S1 ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f55f10c19a0848edd2466d08744556eb
: endThanks for helping me again. I really appreciate.
I don't hve any NAT-exemptions in Cisco IOS Router. Transform-set I will change soon, but I've tried with tunnel mode and it didn't work.
Maybe NAT-exemptions is the issue. Can you advice me which exemptions should be in Cisco IOS Router?
Because on Cisco ASA I guess I have everything.
Here is show crypto session detail
router(config)#do show crypto session detail
Crypto session current status
Code: C - IKE Configuration mode, D - Dead Peer Detection
K - Keepalives, N - NAT-traversal, T - cTCP encapsulation
X - IKE Extended Authentication, F - IKE Fragmentation
Interface: GigabitEthernet0/0
Session status: DOWN
Peer: 198.0.183.225 port 500 fvrf: (none) ivrf: (none)
Desc: (none)
Phase1_id: (none)
IPSEC FLOW: permit ip 192.168.17.0/255.255.255.0 192.168.83.0/255.255.255.0
Active SAs: 0, origin: crypto map
Inbound: #pkts dec'ed 0 drop 0 life (KB/Sec) 0/0
Outbound: #pkts enc'ed 0 drop 0 life (KB/Sec) 0/0
Should I see something in crypto isakmp sa?
pp-border#sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst src state conn-id status
IPv6 Crypto ISAKMP SA
Thanks again for your help. -
ASA 5510 Not able to route traffic between 2 LAN interfaces
Hi everybody,
I need help to enable traffic between two physical ports on my Cisco ASA 5510. I created access rules and NAT but traffic doe not go from accounting interface to Inside. I am able to access internet from both interfaces. Can someone pin point me in the right direction since I am not an expert in Cisco but has to finish this by the end of the week.
Thank you,
Sigor
Here is my configuration:
ASA Version 8.2(2)
hostname Cisco
domain-name xxx.com
names
interface Ethernet0/0
description Outside
nameif Outside
security-level 0
ip address 101.101.101.101 255.255.240.0
interface Ethernet0/1
description Inside Network
nameif Inside
security-level 90
ip address 192.168.10.1 255.255.255.0
interface Ethernet0/2
description Accounting
nameif Accounting
security-level 100
ip address 20.0.1.1 255.255.255.0
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
management-only
ftp mode passive
clock timezone EST -5
dns domain-lookup Outside
dns server-group DefaultDNS
name-server 8.8.8.8
domain-name xxx.com
same-security-traffic permit inter-interface
object-group service Port-10000 tcp
port-object eq 10000
object-group service Port-8080 tcp
port-object eq 8080
object-group service Port-8011 tcp
port-object eq 8011
object-group service DM_INLINE_TCP_1 tcp
group-object Port-8080
port-object eq www
group-object Port-8011
object-group service DM_INLINE_TCP_2 tcp
group-object Port-10000
port-object eq https
port-object eq www
object-group service rdp tcp
port-object eq 3389
object-group service DM_INLINE_TCP_3 tcp
group-object rdp
port-object eq ftp
object-group service DM_INLINE_TCP_4 tcp
group-object Port-10000
port-object eq www
port-object eq https
port-object eq ssh
object-group service DM_INLINE_TCP_5 tcp
group-object Port-8011
group-object Port-8080
port-object eq www
object-group service DM_INLINE_TCP_6 tcp
group-object Port-10000
port-object eq www
port-object eq https
object-group service DM_INLINE_TCP_7 tcp
group-object rdp
port-object eq ftp
access-list Outside_access_in extended permit tcp any host 101.101.101.104 object-group DM_INLINE_TCP_5
access-list Outside_access_in extended permit tcp any host 101.101.101.102 object-group DM_INLINE_TCP_6
access-list Outside_access_in extended permit tcp any host 101.101.101.103 object-group DM_INLINE_TCP_7
access-list Outside_access_in extended permit tcp any host 101.101.101.106 eq smtp
access-list Outside_1_cryptomap extended permit ip 192.168.10.0 255.255.255.0 192.168.50.0 255.255.255.0
access-list Inside_nat0_outbound extended permit ip 192.168.10.0 255.255.255.0 192.168.50.0 255.255.255.0
access-list Inside_nat0_outbound extended permit ip 192.168.10.0 255.255.255.0 192.168.80.0 255.255.255.0
access-list CiscoIPsec_splitTunnelAcl standard permit 192.168.10.0 255.255.255.0
access-list Accounting extended permit ip 20.0.1.0 255.255.255.0 192.168.10.0 255.255.255.0
access-list Accounting extended permit ip 20.0.1.0 255.255.255.0 any
pager lines 24
logging asdm informational
mtu Outside 1500
mtu Inside 1500
mtu Accounting 1500
mtu management 1500
ip local pool IPSecDHCP 192.168.80.100-192.168.80.200 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (Outside) 1 interface
nat (Inside) 0 access-list Inside_nat0_outbound
nat (Inside) 1 0.0.0.0 0.0.0.0
nat (Accounting) 1 0.0.0.0 0.0.0.0
static (Inside,Outside) tcp 101.101.101.104 www 192.168.10.14 www netmask 255.255.255.255
static (Inside,Outside) tcp 101.101.101.104 8011 192.168.10.14 8011 netmask 255.255.255.255
static (Inside,Outside) tcp 101.101.101.104 8080 192.168.10.14 8080 netmask 255.255.255.255
static (Inside,Outside) tcp 101.101.101.102 10000 192.168.10.3 10000 netmask 255.255.255.255
static (Inside,Outside) tcp 101.101.101.102 https 192.168.10.3 https netmask 255.255.255.255
static (Inside,Outside) tcp 101.101.101.102 www 192.168.10.3 www netmask 255.255.255.255
static (Inside,Outside) tcp 101.101.101.103 ftp 192.168.10.17 ftp netmask 255.255.255.255
static (Inside,Outside) tcp 101.101.101.103 3389 192.168.10.32 3389 netmask 255.255.255.255
static (Inside,Outside) tcp 101.101.101.106 smtp 192.168.10.23 smtp netmask 255.255.255.255
static (Inside,Accounting) 192.168.10.0 192.168.10.0 netmask 255.255.255.0
access-group Outside_access_in in interface Outside
access-group Accounting in interface Accounting
route Outside 0.0.0.0 0.0.0.0 101.101.101.101 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 192.168.10.0 255.255.255.0 Inside
http 20.0.1.0 255.255.255.0 Accounting
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 32608000
crypto ipsec security-association replay disable
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256
-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set security-association lifetime kilobytes 4608000
crypto map Outside_map 1 match address Outside_1_cryptomap
crypto map Outside_map 1 set pfs group1
crypto map Outside_map 1 set peer 89.216.17.35
crypto map Outside_map 1 set transform-set ESP-3DES-SHA
crypto map Outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map Outside_map interface Outside
crypto isakmp enable Outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 192.168.10.0 255.255.255.0 Inside
ssh timeout 5
console timeout 0
dhcpd address 20.0.1.100-20.0.1.200 Accounting
dhcpd dns 192.168.10.19 8.8.8.8 interface Accounting
dhcpd lease 306800 interface Accounting
dhcpd domain abtscs.com interface Accounting
dhcpd enable Accounting
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy CiscoIPsec internal
group-policy CiscoIPsec attributes
dns-server value 192.168.10.30 192.168.10.19
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value CiscoIPsec_splitTunnelAcl
default-domain value xxx.com
vpn-group-policy CiscoIPsec
tunnel-group 198.226.20.35 type ipsec-l2l
tunnel-group 198.226.20.35 ipsec-attributes
pre-shared-key *****
tunnel-group CiscoIPsec type remote-access
tunnel-group CiscoIPsec general-attributes
address-pool IPSecDHCP
default-group-policy CiscoIPsec
tunnel-group CiscoIPsec ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
Cryptochecksum:2a7c97a7a22397908ef83ca6f0065919
: endWithout diving too deep into your config, I noticed a couple of things:
interface Ethernet0/1
description Inside Network
nameif Inside
security-level 90
ip address 192.168.10.1 255.255.255.0
interface Ethernet0/2
description Accounting
nameif Accounting
security-level 100
ip address 20.0.1.1 255.255.255.0
On an ASA, higher security level interfaces are always allowed, by default, to lower security levels, but not the other way around. So, if you want to keep this config, you would need an acl on the Inside interface to allow traffic to go from level 90 to 100:
access-list Inside permit ip any any
access-group Inside in interface Inside
The acl will permit the traffic into either interface (outside or Accounting). As long as you have your other rules set up correctly, this should resolve your issue...
HTH,
John -
S2S between Cisco ASA 5505 and Sonicwall TZ-170 but not able to ping across
Hi,
I am helping out a friend of mine with his Site-to-Site VPN between his companies Cisco ASA another company's SonicWall TZ-170. I have checked the screenshots proivded by the other end and tried to match with ours. The Tunnel shows but we are not able to Ping resources on the other end. The other side insists that the problem is on our end but I am not sure where the issue resides. Please take a look at our config and let me know if there is anything that I have missed. I am pretty sure I didn't but extra eyes may be of need here.
Our LAN is 10.200.x.x /16 and theirs is 192.168.9.0 /24
ASA Version 8.2(2)
terminal width 300
hostname company-asa
domain-name Company.com
no names
name 10.1.0.0 sacramento-network
name 10.3.0.0 irvine-network
name 10.2.0.0 portland-network
name x.x.x.x MailLive
name 192.168.9.0 revit-vpn-remote-subnet
dns-guard
interface Ethernet0/0
nameif outside
security-level 0
ip address x.x.x.x 255.255.255.128
interface Ethernet0/1
nameif inside
security-level 100
ip address 10.200.200.1 255.255.0.0
interface Ethernet0/2
nameif dmz
security-level 50
ip address 172.22.22.1 255.255.255.0
interface Ethernet0/3
description Internal Wireless
shutdown
nameif Wireless
security-level 100
ip address 10.201.201.1 255.255.255.0
interface Management0/0
shutdown
nameif management
security-level 100
no ip address
management-only
boot system disk0:/asa822-k8.bin
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
dns domain-lookup outside
dns server-group DefaultDNS
domain-name company.com
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group network local_net_group
network-object 10.1.0.0 255.255.0.0
network-object 10.2.0.0 255.255.0.0
network-object 10.200.0.0 255.255.0.0
network-object 10.3.0.0 255.255.0.0
network-object 10.4.0.0 255.255.0.0
network-object 10.5.0.0 255.255.0.0
network-object 10.6.0.0 255.255.0.0
network-object 10.7.0.0 255.255.0.0
network-object 192.168.200.0 255.255.255.0
object-group network NACIO123
network-object 1.1.1.1 255.255.255.224
object-group service MAIL_HTTPS_BORDERWARE tcp
port-object eq smtp
port-object eq https
port-object eq 10101
object-group service SYSLOG_SNMP_NETFLOW udp
port-object eq syslog
port-object eq snmp
port-object eq 2055
object-group service HTTP_HTTPS tcp
port-object eq www
port-object eq https
object-group network OUTSIDECO_SERVERS
network-object host x.x.x.34
network-object host x.x.x.201
network-object host x.x.x.63
object-group network NO-LOG
network-object host 10.200.200.13
network-object host 10.200.200.25
network-object host 10.200.200.32
object-group service iPhoneSync-Services-TCP tcp
port-object eq 993
port-object eq 990
port-object eq 998
port-object eq 5678
port-object eq 5721
port-object eq 26675
object-group service termserv tcp
description terminal services
port-object eq 3389
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group service DTI tcp
description DCS CONTROL PROTOCOL
port-object eq 3333
object-group service H.245 tcp
description h.245 signaling
port-object range 1024 4999
object-group service RAS udp
port-object eq 1719
port-object range 1718 1720
object-group service XML tcp
port-object range 3336 3341
object-group service mpi tcp
port-object eq 2010
object-group service mvp_control tcp
port-object eq 2946
object-group service rpc tcp-udp
port-object eq 1809
object-group service tcp8080 tcp
port-object eq 8080
object-group service tcp8011 tcp
port-object eq 8011
object-group service rtp_rtcp_udp udp
port-object range 1024 65535
object-group service ecs_xml tcp-udp
port-object eq 3271
object-group service rtp20000 udp
description 10000-65535
port-object range 20000 25000
port-object range 10000 65535
object-group service tcp5222 tcp
port-object range 5222 5269
object-group service tcp7070 tcp
port-object eq 7070
object-group network videoco
network-object host x.x.x.144
network-object host x.x.x.145
object-group service video tcp
port-object range 1718 h323
object-group service XML2 tcp-udp
port-object range 3336 3345
object-group service tcp_tls tcp
port-object eq 5061
object-group service Autodesk tcp
port-object eq 2080
port-object range 27000 27009
access-list outside_policy remark ====== Begin Mail From Postini Network ======
access-list outside_policy extended permit tcp x.x.x.x 255.255.240.0 host x.x.x.x eq smtp
access-list outside_policy extended permit tcp x.x.x.x 255.255.255.240 host x.x.x.x eq smtp
access-list outside_policy extended permit tcp x.x.x.0 255.255.240.0 host x.x.x.x eq smtp
access-list outside_policy remark ****** End Mail From Postini Network ******
access-list outside_policy remark ====== Begin Inbound Web Mail Access ======
access-list outside_policy extended permit tcp any host x.x.x.x object-group HTTP_HTTPS
access-list outside_policy remark ****** End Inbound Web Mail Access ******
access-list outside_policy remark ====== Begin iPhone Sync Rules to Mail Server ======
access-list outside_policy extended permit tcp any host x.x.x.x object-group iPhoneSync-Services-TCP
access-list outside_policy remark ****** End iPhone Sync Rules to Mail Server ******
access-list outside_policy remark ====== Begin MARS Monitoring ======
access-list outside_policy extended permit udp x.x.x.x 255.255.255.128 host x.x.x.x object-group SYSLOG_SNMP_NETFLOW
access-list outside_policy extended permit icmp x.x.x.x 255.255.255.128 host x.x.x.x
access-list outside_policy remark ****** End MARS Monitoring ******
access-list outside_policy extended permit tcp object-group NACIO123 host x.x.x.141 eq ssh
access-list outside_policy extended permit tcp any host x.x.x.x eq www
access-list outside_policy extended permit tcp any host x.x.x.x eq https
access-list outside_policy extended permit tcp any host x.x.x.x eq h323
access-list outside_policy extended permit tcp any host x.x.x.x range 60000 60001
access-list outside_policy extended permit udp any host x.x.x.x range 60000 60007
access-list outside_policy remark radvision 5110 port 80 both
access-list outside_policy extended permit object-group TCPUDP any object-group videoco eq www
access-list outside_policy remark radvision
access-list outside_policy extended permit tcp any object-group videoco object-group termserv
access-list outside_policy remark radvision 5110 port21 out
access-list outside_policy extended permit tcp any object-group videoco eq ftp
access-list outside_policy remark rad5110 port22 both
access-list outside_policy extended permit tcp any object-group videoco eq ssh
access-list outside_policy remark rad 5110 port161 udp both
access-list outside_policy extended permit udp any object-group videoco eq snmp
access-list outside_policy remark rad5110 port443 both
access-list outside_policy extended permit tcp any object-group videoco eq https
access-list outside_policy remark rad5110 port 1024-4999 both
access-list outside_policy extended permit tcp any object-group videoco object-group H.245
access-list outside_policy remark rad5110 port 1719 udp both
access-list outside_policy extended permit udp any object-group videoco object-group RAS
access-list outside_policy remark rad5110 port 1720 both
access-list outside_policy extended permit tcp any any eq h323
access-list outside_policy remark RAD 5110 port 3333 tcp both
access-list outside_policy extended permit tcp any object-group videoco object-group DTI
access-list outside_policy remark rad5110 port 3336-3341 both
access-list outside_policy extended permit object-group TCPUDP any object-group videoco object-group XML2
access-list outside_policy remark port 5060 tcp/udp
access-list outside_policy extended permit object-group TCPUDP any object-group videoco eq sip
access-list outside_policy remark rad 5110port 1809 rpc both
access-list outside_policy extended permit object-group TCPUDP any object-group videoco object-group rpc
access-list outside_policy remark rad 5110 port 2010 both
access-list outside_policy extended permit tcp any object-group videoco object-group mpi
access-list outside_policy remark rad 5110 port 2946 both
access-list outside_policy extended permit tcp any object-group videoco object-group mvp_control
access-list outside_policy extended permit tcp any object-group videoco object-group tcp8080
access-list outside_policy extended permit tcp any object-group videoco object-group tcp8011
access-list outside_policy remark 1024-65535
access-list outside_policy extended permit udp any object-group videoco object-group rtp_rtcp_udp
access-list outside_policy extended permit object-group TCPUDP any object-group videoco object-group ecs_xml
access-list outside_policy extended permit udp any object-group videoco object-group rtp20000
access-list outside_policy extended permit tcp any object-group videoco eq telnet
access-list outside_policy remark port 53 dns
access-list outside_policy extended permit object-group TCPUDP any object-group videoco eq domain
access-list outside_policy remark 7070
access-list outside_policy extended permit tcp any object-group videoco object-group tcp7070
access-list outside_policy remark 5222-5269 tcp
access-list outside_policy extended permit tcp any object-group videoco range 5222 5269
access-list outside_policy extended permit tcp any object-group videoco object-group video
access-list outside_policy extended permit tcp any object-group videoco object-group tcp_tls
access-list outside_policy remark ====== Begin Autodesk Activation access ======
access-list outside_policy extended permit tcp any any object-group Autodesk
access-list outside_policy remark ****** End Autodesk Activation access ******
access-list outside_policy extended permit tcp x.x.x.x 255.255.255.248 host x.x.x.x eq smtp
access-list outside_policy remark ****** End Autodesk Activation access ******
access-list inside_policy extended deny tcp host 10.200.200.25 10.1.0.0 255.255.0.0 eq 2967 log disable
access-list inside_policy extended deny tcp host 10.200.200.25 10.3.0.0 255.255.0.0 eq 2967 log disable
access-list inside_policy extended deny tcp host 10.200.200.25 10.2.0.0 255.255.0.0 eq 2967 log disable
access-list inside_policy extended deny tcp host 10.200.200.25 10.4.0.0 255.255.0.0 eq 2967 log disable
access-list inside_policy extended deny tcp host 10.200.200.25 10.5.0.0 255.255.0.0 eq 2967 log disable
access-list inside_policy extended deny udp object-group NO-LOG any eq 2967 log disable
access-list inside_policy extended deny tcp object-group NO-LOG any eq 2967 log disable
access-list inside_policy remark ====== Begin Outbound Mail Server Rules ======
access-list inside_policy extended permit udp host 10.200.200.222 any eq 5679
access-list inside_policy extended permit tcp host 10.200.200.222 any eq smtp
access-list inside_policy remark ****** End Outbound Mail Server Rules ******
access-list inside_policy extended permit ip object-group local_net_group any
access-list inside_policy extended permit icmp object-group local_net_group any
access-list OUTSIDECO_VPN extended permit ip host x.x.x.x object-group OUTSIDECO_SERVERS
access-list company-split-tunnel standard permit 10.1.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.2.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.3.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.4.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.200.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.5.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.6.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.7.0.0 255.255.0.0
access-list company-split-tunnel standard permit 172.22.22.0 255.255.255.0
access-list company-split-tunnel remark Video
access-list company-split-tunnel standard permit 192.168.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.1.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.2.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.3.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.200.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.4.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.5.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.6.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.7.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 172.22.22.0 255.255.255.0
access-list SSL_SPLIT remark Video
access-list SSL_SPLIT standard permit 192.168.0.0 255.255.0.0
access-list NONAT_SSL extended permit ip object-group local_net_group 172.20.20.0 255.255.255.0
access-list NONAT_SSL extended permit ip 10.200.0.0 255.255.0.0 192.168.9.0 255.255.255.0
access-list tom extended permit tcp host x.x.x.x any eq smtp
access-list tom extended permit tcp host 10.200.200.222 any eq smtp
access-list tom extended permit tcp any host x.x.x.x
access-list aaron extended permit tcp any any eq 2967
access-list capauth extended permit ip host 10.200.200.1 host 10.200.200.220
access-list capauth extended permit ip host 10.200.200.220 host 10.200.200.1
access-list DMZ extended permit icmp any any
access-list dmz_access_in extended permit tcp any eq 51024 any eq 3336
access-list dmz_access_in extended permit icmp any any
access-list dmz_access_in extended permit tcp any any eq ftp
access-list dmz_access_in extended permit tcp any any eq https
access-list dmz_access_in remark rad5110 port 162 out
access-list dmz_access_in extended permit udp any any eq snmptrap
access-list dmz_access_in remark port 23 out
access-list dmz_access_in extended permit tcp any any eq telnet
access-list dmz_access_in remark port 53 dns out
access-list dmz_access_in extended permit object-group TCPUDP any any eq domain
access-list dmz_access_in extended permit object-group TCPUDP any any eq www
access-list dmz_access_in extended permit tcp any any eq h323
access-list dmz_access_in extended permit tcp any any object-group XML
access-list dmz_access_in extended permit udp any any object-group RAS
access-list dmz_access_in extended permit tcp any any range 1718 h323
access-list dmz_access_in extended permit tcp any any object-group H.245
access-list dmz_access_in extended permit object-group TCPUDP any any eq sip
access-list dmz_access_in extended permit udp any any object-group rtp_rtcp_udp
access-list dmz_access_in extended permit object-group TCPUDP any any object-group XML2
access-list dmz_access_in extended permit ip object-group local_net_group any
access-list dmz_access_in remark port 5061
access-list dmz_access_in extended permit tcp any any object-group tcp_tls
access-list outside_cryptomap extended permit ip 10.200.0.0 255.255.0.0 192.168.9.0 255.255.255.0
pager lines 24
logging enable
logging buffered warnings
logging trap informational
logging history informational
logging asdm warnings
logging host outside x.x.x.x
mtu outside 1500
mtu inside 1500
mtu dmz 1500
mtu Wireless 1500
mtu management 1500
ip local pool SSL_VPN_POOL 172.20.20.1-172.20.20.75 mask 255.255.255.0
ip verify reverse-path interface outside
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-631.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list NONAT_SSL
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) x.x.x.12 10.200.200.15 netmask 255.255.255.255
static (inside,outside) x.x.x.15 10.5.0.11 netmask 255.255.255.255
static (inside,outside) x.x.x.13 10.200.200.240 netmask 255.255.255.255
static (inside,outside) x.x.x.16 10.200.200.222 netmask 255.255.255.255
static (inside,outside) x.x.x.14 10.200.200.155 netmask 255.255.255.255
static (inside,dmz) 10.200.200.0 10.200.200.0 netmask 255.255.255.0
static (inside,dmz) 10.4.0.0 10.4.0.0 netmask 255.255.0.0
static (dmz,outside) x.x.x.18 172.22.22.15 netmask 255.255.255.255
static (dmz,outside) x.x.x.19 172.22.22.16 netmask 255.255.255.255
static (inside,dmz) 10.3.0.0 10.3.0.0 netmask 255.255.0.0
static (inside,dmz) 10.2.0.0 10.2.0.0 netmask 255.255.0.0
static (inside,dmz) 10.1.0.0 10.1.0.0 netmask 255.255.0.0
static (inside,dmz) 10.6.0.0 10.6.0.0 netmask 255.255.0.0
static (inside,dmz) 10.7.0.0 10.7.0.0 netmask 255.255.0.0
static (inside,dmz) 10.5.0.0 10.5.0.0 netmask 255.255.0.0
access-group outside_policy in interface outside
access-group inside_policy in interface inside
access-group dmz_access_in in interface dmz
route outside 0.0.0.0 0.0.0.0 x.x.x.12 1
route inside 10.1.0.0 255.255.0.0 10.200.200.254 1
route inside 10.2.0.0 255.255.0.0 10.200.200.254 1
route inside 10.3.0.0 255.255.0.0 10.200.200.254 1
route inside 10.4.0.0 255.255.0.0 10.200.200.254 1
route inside 10.5.0.0 255.255.0.0 10.200.200.254 1
route inside 10.6.0.0 255.255.0.0 10.200.200.254 1
route inside 10.7.0.0 255.255.0.0 10.200.200.150 1
route inside x.x.x.0 255.255.255.0 10.200.200.2 1
route inside x.x.x.0 255.255.255.0 10.200.200.2 1
route inside 192.168.1.0 255.255.255.0 10.200.200.254 1
route inside 192.168.2.0 255.255.255.0 10.200.200.254 1
route inside 192.168.3.0 255.255.255.0 10.200.200.254 1
route inside 192.168.4.0 255.255.255.0 10.200.200.254 1
route inside 192.168.5.0 255.255.255.0 10.200.200.254 1
route inside 192.168.6.0 255.255.255.0 10.200.200.254 1
route inside 192.168.7.0 255.255.255.0 10.200.200.254 1
route inside 192.168.200.0 255.255.255.0 10.200.200.254 1
route inside 192.168.201.0 255.255.255.0 10.200.200.254 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 2:00:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server COMPANY-NT-AUTH protocol nt
aaa-server COMPANY-NT-AUTH (inside) host 10.200.200.220
nt-auth-domain-controller DC
aaa authentication ssh console LOCAL
aaa authorization command LOCAL
http server enable
http 10.200.200.0 255.255.255.0 inside
http 10.200.0.0 255.255.0.0 inside
http 10.3.0.0 255.255.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set AES256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set asa2transform esp-3des esp-sha-hmac
crypto ipsec transform-set 3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map outside_dyn_map 20 set transform-set 3DES-SHA
crypto dynamic-map outside_dyn_map 20 set security-association lifetime seconds 28800
crypto dynamic-map outside_dyn_map 20 set security-association lifetime kilobytes 4608000
crypto map OUTSIDE_MAP 5 match address outside_cryptomap
crypto map OUTSIDE_MAP 5 set pfs
crypto map OUTSIDE_MAP 5 set peer x.x.x.53
crypto map OUTSIDE_MAP 5 set transform-set 3DES-SHA
crypto map OUTSIDE_MAP 5 set security-association lifetime seconds 28800
crypto map OUTSIDE_MAP 10 match address OUTSIDECO_VPN
crypto map OUTSIDE_MAP 10 set peer x.x.x.25
crypto map OUTSIDE_MAP 10 set transform-set AES256-SHA
crypto map OUTSIDE_MAP 10 set security-association lifetime seconds 28800
crypto map OUTSIDE_MAP 10 set security-association lifetime kilobytes 4608000
crypto map OUTSIDE_MAP 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map OUTSIDE_MAP interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 28800
crypto isakmp policy 10
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh 0.0.0.0 0.0.0.0 inside
ssh timeout 20
console timeout 0
dhcpd dns 10.200.200.220 10.200.200.225
dhcpd wins 10.200.200.220 10.200.200.225
dhcpd lease 18000
dhcpd domain company.com
dhcpd dns 10.200.200.220 10.200.200.225 interface Wireless
dhcpd wins 10.200.200.220 10.200.200.225 interface Wireless
dhcpd lease 18000 interface Wireless
dhcpd domain company.com interface Wireless
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 192.5.41.40 source outside prefer
ssl trust-point vpn.company.com outside
webvpn
enable outside
anyconnect-essentials
svc image disk0:/anyconnect-win-2.5.0217-k9.pkg 1
svc image disk0:/anyconnect-macosx-i386-2.5.2017-k9.pkg 2
svc enable
tunnel-group-list enable
group-policy SSL_Client_Policy internal
group-policy SSL_Client_Policy attributes
wins-server value 10.200.200.220
dns-server value 10.200.200.220
vpn-tunnel-protocol IPSec svc webvpn
split-tunnel-policy tunnelspecified
split-tunnel-network-list value SSL_SPLIT
default-domain value company.com
webvpn
sso-server none
auto-signon allow uri * auth-type all
group-policy no-split-test internal
group-policy no-split-test attributes
banner value Welcome to company and Associates
banner value Welcome to company and Associates
dns-server value 10.200.200.220
vpn-tunnel-protocol IPSec
ipsec-udp enable
split-tunnel-policy tunnelall
default-domain value company.com
group-policy DfltGrpPolicy attributes
dns-server value 10.200.200.220
default-domain value company.com
group-policy company internal
group-policy company attributes
banner value Welcome to company and Associates
banner value Welcome to company and Associates
dns-server value 10.200.200.220
vpn-tunnel-protocol IPSec
ipsec-udp enable
split-tunnel-policy tunnelspecified
split-tunnel-network-list value SSL_SPLIT
default-domain value company.com
username ciscoadmin password xxxxxxxxxxx encrypted privilege 15
tunnel-group DefaultWEBVPNGroup general-attributes
address-pool SSL_VPN_POOL
authentication-server-group COMPANY-NT-AUTH
default-group-policy SSL_Client_Policy
tunnel-group DefaultWEBVPNGroup webvpn-attributes
group-alias company_SSL_VPN enable
tunnel-group company_group type remote-access
tunnel-group company_group general-attributes
address-pool SSL_VPN_POOL
authentication-server-group COMPANY-NT-AUTH LOCAL
default-group-policy company
tunnel-group company_group ipsec-attributes
pre-shared-key *****
tunnel-group x.x.x.53 type ipsec-l2l
tunnel-group x.x.x.53 ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map global_policy
class inspection_default
inspect tftp
inspect esmtp
inspect ftp
inspect icmp
inspect ip-options
inspect netbios
inspect rsh
inspect skinny
inspect sqlnet
inspect sunrpc
inspect xdmcp
inspect mgcp
inspect h323 h225
inspect h323 ras
inspect sip
service-policy global_policy global
privilege cmd level 5 mode exec command ping
privilege cmd level 6 mode exec command write
privilege show level 5 mode exec command running-config
privilege show level 5 mode exec command version
privilege show level 5 mode exec command conn
privilege show level 5 mode exec command memory
privilege show level 5 mode exec command cpu
privilege show level 5 mode exec command xlate
privilege show level 5 mode exec command traffic
privilege show level 5 mode exec command interface
privilege show level 5 mode exec command clock
privilege show level 5 mode exec command ip
privilege show level 5 mode exec command failover
privilege show level 5 mode exec command arp
privilege show level 5 mode exec command route
privilege show level 5 mode exec command blocks
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:a0689b4c837c79a51e7a0cfed591dec9
: end
COMPANY-asa#Hi Sian,
Yes on their end the PFS is enabled for DH Group 2.
Here is the information that you requested:
company-asa# sh crypto isakmp sa
Active SA: 3
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 3
1 IKE Peer: x.x.x.87
Type : user Role : responder
Rekey : no State : AM_ACTIVE
2 IKE Peer: x.x.x.53
Type : L2L Role : initiator
Rekey : no State : MM_ACTIVE
3 IKE Peer: x.x.x.25
Type : user Role : initiator
Rekey : no State : MM_WAIT_MSG4
company-asa# sh crypto ipsec sa
interface: outside
Crypto map tag: OUTSIDE_MAP, seq num: 5, local addr: x.x.x.13
access-list outside_cryptomap extended permit ip 10.200.0.0 255.255.0.0 192.168.9.0 255.255.255.0
local ident (addr/mask/prot/port): (10.200.0.0/255.255.0.0/0/0)
remote ident (addr/mask/prot/port): (192.168.9.0/255.255.255.0/0/0)
current_peer: x.x.x.53
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
#pkts decaps: 10744, #pkts decrypt: 10744, #pkts verify: 10744
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: x.x.x.13, remote crypto endpt.: x.x.x.53
path mtu 1500, ipsec overhead 58, media mtu 1500
current outbound spi: 500EC8BF
current inbound spi : 8DAE3436
inbound esp sas:
spi: 0x8DAE3436 (2377004086)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 32768, crypto-map: OUTSIDE_MAP
sa timing: remaining key lifetime (kB/sec): (3914946/24388)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0xFFFFFFFF 0xFFFFFFFF
outbound esp sas:
spi: 0x500EC8BF (1343146175)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 32768, crypto-map: OUTSIDE_MAP
sa timing: remaining key lifetime (kB/sec): (3915000/24388)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
Crypto map tag: outside_dyn_map, seq num: 20, local addr: x.x.x.13
local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
remote ident (addr/mask/prot/port): (172.20.20.8/255.255.255.255/0/0)
current_peer: x.x.x.87, username: ewebb
dynamic allocated peer ip: 172.20.20.8
#pkts encaps: 16434, #pkts encrypt: 16464, #pkts digest: 16464
#pkts decaps: 19889, #pkts decrypt: 19889, #pkts verify: 19889
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 16434, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 30, #pre-frag failures: 0, #fragments created: 60
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 60
#send errors: 0, #recv errors: 0
local crypto endpt.: x.x.x.13/4500, remote crypto endpt.: x.x.x.87/2252
path mtu 1500, ipsec overhead 66, media mtu 1500
current outbound spi: 2D712C9F
current inbound spi : 0EDB79C8
inbound esp sas:
spi: 0x0EDB79C8 (249264584)
transform: esp-3des esp-sha-hmac no compression
in use settings ={RA, Tunnel, NAT-T-Encaps, }
slot: 0, conn_id: 65536, crypto-map: outside_dyn_map
sa timing: remaining key lifetime (sec): 18262
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0xFFFFFFFF 0xFFFFFFFF
outbound esp sas:
spi: 0x2D712C9F (762391711)
transform: esp-3des esp-sha-hmac no compression
in use settings ={RA, Tunnel, NAT-T-Encaps, }
slot: 0, conn_id: 65536, crypto-map: outside_dyn_map
sa timing: remaining key lifetime (sec): 18261
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001 -
Cisco ASA 5505 - IPsec Tunnel issue
Issue with IPsec Child SA
Hi,
I have a site to site VPN tunnel setup with a Cisco ASA5505 and a Checkpoint Firewall. The version of software is 9.22. I am using IKEv2 for Phase 1 encryption. The following is my cisco asa configuration:
hostname GARPR-COM1-WF01
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
names
interface Ethernet0/0
description Failover Link
switchport access vlan 950
interface Ethernet0/1
description Outside FW Link
switchport access vlan 999
interface Ethernet0/2
description Inside FW Link
switchport access vlan 998
interface Ethernet0/3
description Management Link
switchport access vlan 6
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
shutdown
interface Vlan1
no nameif
no security-level
no ip address
interface Vlan6
nameif management
security-level 100
ip address 10.65.1.20 255.255.255.240
interface Vlan950
description LAN Failover Interface
interface Vlan998
nameif inside
security-level 100
ip address 10.65.1.5 255.255.255.252
interface Vlan999
nameif outside
security-level 0
ip address ************* 255.255.255.248
boot system disk0:/asa922-4-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name ***************
object network North_American_LAN
subnet 10.73.0.0 255.255.0.0
description North American LAN
object network Queretaro_LAN
subnet 10.74.0.0 255.255.0.0
description Queretaro_LAN
object network Tor_LAN
subnet 10.75.0.0 255.255.0.0
description Tor LAN
object network Mor_LAN
subnet 10.76.0.0 255.255.0.0
description Mor LAN
object network Tus_LAN
subnet 10.79.128.0 255.255.128.0
description North American LAN
object network Mtl_LAN
subnet 10.88.0.0 255.255.0.0
description Mtl LAN
object network Wic_LAN
subnet 10.90.0.0 255.254.0.0
description Wic LAN
object network Wic_LAN_172
subnet 172.18.0.0 255.255.0.0
description Wic Servers/Legacy Client LAN
object network Mtl_LAN_172
subnet 172.19.0.0 255.255.0.0
description Mtl Servers/Legacy Client LAN
object network Tor_LAN_172
subnet 172.20.0.0 255.255.0.0
description Tor Servers/Legacy Client LAN
object network Bridge_LAN_172
subnet 172.23.0.0 255.255.0.0
description Bridge Servers/Legacy Client LAN
object network Mtl_WLAN
subnet 10.114.0.0 255.255.0.0
description Mtl Wireless LAN
object network Bel_WLAN
subnet 10.115.0.0 255.255.0.0
description Bel Wireless LAN
object network Wic_WLAN
subnet 10.116.0.0 255.255.0.0
description Wic Wireless LAN
object network Mtl_Infrastructure_10
subnet 10.96.0.0 255.255.0.0
description Mtl Infrastructre LAN
object network BA_Small_Site_Blocks
subnet 10.68.0.0 255.255.0.0
description BA Small Sites Blocks
object network Bel_LAN
subnet 10.92.0.0 255.255.0.0
description Bel LAN 10 Network
object network LAN_172
subnet 172.25.0.0 255.255.0.0
description LAN 172 Network
object network Gar_LAN
subnet 10.65.1.0 255.255.255.0
description Gar LAN
object network garpr-com1-wf01.net.aero.bombardier.net
host **************
description Garching Firewall
object-group network BA_Sites
description Internal Networks
network-object object BA_Small_Site_Blocks
network-object object Bel_LAN
network-object object Bel_LAN_172
network-object object Bel_WLAN
network-object object Bridge_LAN_172
network-object object Mtl_Infrastructure_10
network-object object Mtl_LAN
network-object object Mtl_LAN_172
network-object object Mtl_WLAN
network-object object Mor_LAN
network-object object North_American_LAN
network-object object Queretaro_LAN
network-object object Tor_LAN
network-object object Tor_LAN_172
network-object object Tus_LAN
network-object object Wic_LAN
network-object object Wic_LAN_172
network-object object Wic_WLAN
access-list 101 extended permit ip object garpr-com1-wf01.net.aero.bombardier.net object Bel_LAN_172
access-list 101 extended permit ip object Garching_LAN object-group BA_Sites
pager lines 24
logging enable
logging timestamp
logging buffered warnings
logging trap informational
logging asdm informational
logging host outside 172.25.5.102
mtu management 1500
mtu inside 1500
mtu outside 1500
failover
failover lan unit primary
failover lan interface Failover_Link Vlan950
failover polltime interface msec 500 holdtime 5
failover key *****
failover interface ip Failover_Link 192.168.124.1 255.255.255.0 standby 192.168.124.2
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-731-101.bin
asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source static Gar_LAN Gar_LAN destination static BA_Sites BA_Sites no-proxy-arp route-lookup
route outside 0.0.0.0 0.0.0.0 ************* 1
route inside 10.65.1.0 255.255.255.255 10.65.1.6 1
route inside 10.65.1.16 255.255.255.240 10.65.1.6 1
route inside 10.65.1.32 255.255.255.240 10.65.1.6 1
route inside 10.65.1.48 255.255.255.240 10.65.1.6 1
route inside 10.65.1.64 255.255.255.240 10.65.1.6 1
route inside 10.65.1.128 255.255.255.128 10.65.1.6 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
aaa authentication telnet console LOCAL
http server enable
http 10.65.1.0 255.255.255.0 inside
http 172.25.5.0 255.255.255.0 inside
http 10.65.1.21 255.255.255.255 management
snmp-server host inside 172.25.49.0 community ***** udp-port 161
snmp-server host outside 172.25.49.0 community *****
snmp-server host inside 172.25.5.101 community ***** udp-port 161
snmp-server host outside 172.25.5.101 community *****
snmp-server host inside 172.25.81.88 poll community *****
snmp-server host outside 172.25.81.88 poll community *****
snmp-server location:
snmp-server contact
snmp-server community *****
snmp-server enable traps syslog
crypto ipsec ikev2 ipsec-proposal aes256
protocol esp encryption aes-256
protocol esp integrity sha-1
crypto ipsec security-association lifetime seconds 3600
crypto ipsec security-association pmtu-aging infinite
crypto map GARCH 10 match address 101
crypto map GARCH 10 set pfs group19
crypto map GARCH 10 set peer *******************
crypto map GARCH 10 set ikev2 ipsec-proposal aes256
crypto map GARCH 10 set security-association lifetime seconds 3600
crypto map GARCH interface outside
crypto ca trustpool policy
no crypto isakmp nat-traversal
crypto ikev2 policy 10
encryption aes-256
integrity sha256
group 19
prf sha256
lifetime seconds 86400
crypto ikev2 enable outside
telnet 10.65.1.6 255.255.255.255 inside
telnet timeout 5
ssh stricthostkeycheck
ssh 172.25.5.0 255.255.255.0 inside
ssh 172.19.9.49 255.255.255.255 inside
ssh 172.25.5.0 255.255.255.0 outside
ssh 172.19.9.49 255.255.255.255 outside
ssh timeout 30
ssh version 2
ssh key-exchange group dh-group1-sha1
console timeout 30
management-access inside
dhcprelay server 172.25.81.1 outside
dhcprelay server 172.25.49.1 outside
dhcprelay enable inside
dhcprelay timeout 60
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 172.19.109.41
ntp server 172.19.109.42
ntp server 172.19.9.49 source outside
tunnel-group ********* type ipsec-l2l
tunnel-group ********* ipsec-attributes
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:25ad9bf6db66a31e840ad96f49cd7e37
: end
I believe when a VPN tunnel is setup there should be one Child sa per subnet. The internal network of 10.65.1.0/24 should be setup with a child sa to the networks that were specified above depending on if there is traffic destined for them. What I am seeing is multiple child sa setup for the same subnet like the example below:
GARPR-COM1-WF01# sh crypto ikev2 sa | i 172.19
remote selector 172.19.0.0/0 - 172.19.255.255/65535
remote selector 172.19.0.0/0 - 172.19.255.255/65535
remote selector 172.19.0.0/0 - 172.19.255.255/65535
remote selector 172.19.0.0/0 - 172.19.255.255/65535
remote selector 172.19.0.0/0 - 172.19.255.255/65535
remote selector 172.19.0.0/0 - 172.19.255.255/65535
remote selector 172.19.0.0/0 - 172.19.255.255/65535
remote selector 172.19.0.0/0 - 172.19.255.255/65535
remote selector 172.19.0.0/0 - 172.19.255.255/65535
remote selector 172.19.0.0/0 - 172.19.255.255/65535
where for destination network 10.92.0.0/16 there is only one child sa:
GARPR-COM1-WF01# sh crypto ikev2 sa | i 10.92
remote selector 10.92.0.0/0 - 10.92.255.255/6553
Should this be the case or does anyone have any idea why there is multiple child sa setup for the same subnet?
Thanks
JonathanHi there,
I had same issue with PIX 506E and it was not even a circuit issue and I got ride of it and problem got fixed with PIX515E
I don't know, the device is too old to stay alive.
thanks -
Cisco ASA 5505 Cannot ping local traffic and local hosts cannot get out
I have, what I believe to be, a simple issue - I must be missing something.
Site to Site VPN with Cisco ASA's. VPN is up, and remote hosts can ping the inside int of ASA (10.51.253.209).
There is a PC (10.51.253.210) plugged into e0/1.
I know the PC is configured correctly with Windows firewall tuned off.
The PC cannot get to the ouside world, and the ASA cannot ping 10.51.253.210.
I have seen this before, and I deleted VLAN 1, recreated it, and I could ping the local host without issue.
Basically, the VPN is up and running but PC 10.51.253.210 cannot get out.
Any ideas? Sanitized Config is below. Thanks !
ASA Version 7.2(4)
hostname *****
domain-name *****
enable password N7FecZuSHJlVZC2P encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif Inside
security-level 100
ip address 10.51.253.209 255.255.255.248
interface Vlan2
nameif Outside
security-level 0
ip address ***** 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
shutdown
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
shutdown
ftp mode passive
dns server-group DefaultDNS
domain-name *****
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 10.1.7.0 255.255.255.0
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.1.10.250
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.200
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.9
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.14
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.15
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.16
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 10.1.9.0 255.255.255.0
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 10.10.9.0 255.255.255.0
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 ***** 255.255.255.240
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 10.1.7.0 255.255.255.0
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.1.10.250
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.200
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.9
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.14
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.15
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.16
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 10.1.9.0 255.255.255.0
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 10.10.9.0 255.255.255.0
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 ***** 255.255.255.240
pager lines 24
mtu Outside 1500
mtu Inside
icmp unreachable rate-limit 1 burst-size 1
icmp permit any Outside
no asdm history enable
arp timeout 14400
global (Outside) 1 interface
nat (Inside) 0 access-list No_NAT
route Outside 0.0.0.0 0.0.0.0 ***** 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
aaa authentication enable console LOCAL
aaa authentication serial console LOCAL
aaa authentication ssh console LOCAL
http server enable
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set DPS_Set esp-3des esp-md5-hmac
crypto map DPS_Map 10 match address Outside_VPN
crypto map DPS_Map 10 set peer *****
crypto map DPS_Map 10 set transform-set *****
crypto map DPS_Map interface Outside
crypto isakmp enable Outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 28800
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 Outside
ssh timeout 60
console timeout 0
management-access Inside
username test password P4ttSyrm33SV8TYp encrypted
tunnel-group ***** type ipsec-l2l
tunnel-group ***** ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
Cryptochecksum:8d0adca63eab6c6c738cc4ab432f609d
: end
1500Hi Martin,
Which way you are trying. Sending traffic via site to site is not working or traffic which you generate to outside world is not working?
But you say ASA connected interface to PC itself is not pinging that is strange. But try setting up the specific rules for the outgoing connection and check. Instead of not having any ACL.
If it is outside world the you may need to check on the NAT rules which is not correct.
If it is site to site then you may need to check few other things.
Please do rate for the helpful posts.
By
Karthik -
Cisco ASA 5505 Routing between internal networks
Hi,
I am new to Cisco ASA and have been configuring my new firewall but one thing have been bothering. I cannot get internal networks and routing between them to work as I would like to. Goal is to set four networks and control access with ACL:s between those.
1. Outside
2. DMZ
3. ServerNet1
4. Inside
ASA version is 9.1 and i have been reading on two different ways on handling IP routing with this. NAT Exempt and not configuring NAT at all and letting normal IP routing to handle internal networks. No matter how I configure, with or without NAT I cannot get access from inside network to DMZ or from ServerNet1 to DMZ. Strange thing is that I can access services from DMZ to Inside and ServerNet1 if access list allows it. For instance DNS server is on Inside network and DMZ works great using it.
Here is the running conf:
interface Ethernet0/0
switchport access vlan 20
interface Ethernet0/1
switchport access vlan 20
interface Ethernet0/2
switchport access vlan 19
interface Ethernet0/3
switchport access vlan 10
switchport trunk allowed vlan 10,19-20
switchport trunk native vlan 1
interface Ethernet0/4
switchport access vlan 10
interface Ethernet0/5
switchport access vlan 10
switchport trunk allowed vlan 10-11,19-20
switchport trunk native vlan 1
switchport mode trunk
interface Ethernet0/6
switchport access vlan 10
switchport trunk allowed vlan 10-11,19-20
switchport trunk native vlan 1
switchport mode trunk
interface Ethernet0/7
switchport access vlan 10
interface Vlan10
nameif inside
security-level 90
ip address 192.168.2.1 255.255.255.0
interface Vlan11
nameif ServerNet1
security-level 100
ip address 192.168.4.1 255.255.255.0
interface Vlan19
nameif DMZ
security-level 10
ip address 192.168.3.1 255.255.255.0
interface Vlan20
nameif outside
security-level 0
ip address dhcp setroute
ftp mode passive
clock timezone EEST 2
clock summer-time EEDT recurring last Sun Mar 3:00 last Sun Oct 4:00
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network obj-192.168.2.0
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.3.0
subnet 192.168.3.0 255.255.255.0
object network DNS
host 192.168.2.10
description DNS Liikenne
object network Srv2
host 192.168.2.10
description DC, DNS, DNCP
object network obj-192.168.4.0
subnet 192.168.4.0 255.255.255.0
object network ServerNet1
subnet 192.168.4.0 255.255.255.0
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group network RFC1918
object-group network InternalNetworks
network-object 192.168.2.0 255.255.255.0
network-object 192.168.3.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object tcp destination eq domain
service-object udp destination eq domain
service-object udp destination eq nameserver
service-object udp destination eq ntp
object-group service DM_INLINE_TCP_1 tcp
port-object eq www
port-object eq https
port-object eq ftp
port-object eq ftp-data
object-group service rdp tcp-udp
description Microsoft RDP
port-object eq 3389
object-group service DM_INLINE_TCP_2 tcp
port-object eq ftp
port-object eq ftp-data
port-object eq www
port-object eq https
object-group service DM_INLINE_SERVICE_2
service-object tcp destination eq domain
service-object udp destination eq domain
object-group network DM_INLINE_NETWORK_1
network-object object obj-192.168.2.0
network-object object obj-192.168.4.0
access-list dmz_access_in extended permit ip object obj-192.168.3.0 object obj_any
access-list dmz_access_in extended deny ip any object-group InternalNetworks
access-list DMZ_access_in extended permit object-group TCPUDP object obj-192.168.3.0 object DNS eq domain
access-list DMZ_access_in extended permit object-group TCPUDP object obj-192.168.3.0 object-group DM_INLINE_NETWORK_1 object-group rdp
access-list DMZ_access_in extended deny ip any object-group InternalNetworks
access-list DMZ_access_in extended permit tcp object obj-192.168.3.0 object obj_any object-group DM_INLINE_TCP_2
access-list inside_access_in extended permit ip object obj-192.168.2.0 object-group InternalNetworks
access-list inside_access_in extended permit object-group TCPUDP object obj-192.168.2.0 object obj_any object-group rdp
access-list inside_access_in extended permit tcp object obj-192.168.2.0 object obj_any object-group DM_INLINE_TCP_1
access-list inside_access_in extended permit object-group DM_INLINE_SERVICE_1 object Srv2 object obj_any
access-list inside_access_in extended permit object-group TCPUDP object obj-192.168.2.0 object obj-192.168.3.0 object-group rdp
access-list ServerNet1_access_in extended permit object-group DM_INLINE_SERVICE_2 any object DNS
access-list ServerNet1_access_in extended permit ip any any
pager lines 24
logging enable
logging asdm informational
mtu ServerNet1 1500
mtu inside 1500
mtu DMZ 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-711-52.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,DMZ) source static obj-192.168.2.0 obj-192.168.2.0 destination static obj-192.168.2.0 obj-192.168.2.0 no-proxy-arp
object network obj_any
nat (inside,outside) dynamic interface
nat (DMZ,outside) after-auto source dynamic obj_any interface destination static obj_any obj_any
nat (ServerNet1,outside) after-auto source dynamic obj-192.168.4.0 interface
access-group ServerNet1_access_in in interface ServerNet1
access-group inside_access_in in interface inside
access-group DMZ_access_in in interface DMZ
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http 192.168.2.0 255.255.255.0 inside
http 192.168.4.0 255.255.255.0 ServerNet1
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
telnet timeout 5
ssh 192.168.4.0 255.255.255.0 ServerNet1
ssh 192.168.2.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymousHi Jouni,
Yep, Finnish would be good also =)
In front of ASA is DSL modem, on the trunk ports is Hyper-V host that uses the trunk ports so that every VM has their VLAN ID defined in the VM level. Everything is working good on that end. Also there is WLAN Access Pois on one of the ASA ports, on the WLAN AP there is the management portal address on DMZ that i have been testing agains (192.168.3.4)
If i configure Dynamic PAT from inside to the DMZ then the traffic starts to work from inside to all hosts on DMZ but thats not the right way to do it so no shortcuts =)
Here is the conf now, still doesnt work:
interface Ethernet0/0
switchport access vlan 20
interface Ethernet0/1
switchport access vlan 20
interface Ethernet0/2
switchport access vlan 19
interface Ethernet0/3
switchport access vlan 10
switchport trunk allowed vlan 10,19-20
switchport trunk native vlan 1
interface Ethernet0/4
switchport access vlan 10
interface Ethernet0/5
switchport access vlan 10
switchport trunk allowed vlan 10-11,19-20
switchport trunk native vlan 1
switchport mode trunk
interface Ethernet0/6
switchport access vlan 10
switchport trunk allowed vlan 10-11,19-20
switchport trunk native vlan 1
switchport mode trunk
interface Ethernet0/7
switchport access vlan 10
interface Vlan10
nameif inside
security-level 90
ip address 192.168.2.1 255.255.255.0
interface Vlan11
nameif ServerNet1
security-level 100
ip address 192.168.4.1 255.255.255.0
interface Vlan19
nameif DMZ
security-level 10
ip address 192.168.3.1 255.255.255.0
interface Vlan20
nameif outside
security-level 0
ip address dhcp setroute
ftp mode passive
clock timezone EEST 2
clock summer-time EEDT recurring last Sun Mar 3:00 last Sun Oct 4:00
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network obj-192.168.2.0
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.3.0
subnet 192.168.3.0 255.255.255.0
object network DNS
host 192.168.2.10
description DNS Liikenne
object network Srv2
host 192.168.2.10
description DC, DNS, DNCP
object network obj-192.168.4.0
subnet 192.168.4.0 255.255.255.0
object network ServerNet1
subnet 192.168.4.0 255.255.255.0
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group network RFC1918
object-group network InternalNetworks
network-object 192.168.2.0 255.255.255.0
network-object 192.168.3.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object tcp destination eq domain
service-object udp destination eq domain
service-object udp destination eq nameserver
service-object udp destination eq ntp
object-group service DM_INLINE_TCP_1 tcp
port-object eq www
port-object eq https
port-object eq ftp
port-object eq ftp-data
object-group service rdp tcp-udp
description Microsoft RDP
port-object eq 3389
object-group service DM_INLINE_TCP_2 tcp
port-object eq ftp
port-object eq ftp-data
port-object eq www
port-object eq https
object-group service DM_INLINE_SERVICE_2
service-object tcp destination eq domain
service-object udp destination eq domain
object-group network DM_INLINE_NETWORK_1
network-object object obj-192.168.2.0
network-object object obj-192.168.4.0
object-group network DEFAULT-PAT-SOURCE
description Default PAT source networks
network-object 192.168.2.0 255.255.255.0
network-object 192.168.3.0 255.255.255.0
network-object 192.168.4.0 255.255.255.0
access-list dmz_access_in extended permit ip object obj-192.168.3.0 object obj_any
access-list dmz_access_in extended deny ip any object-group InternalNetworks
access-list DMZ_access_in extended permit object-group TCPUDP object obj-192.168.3.0 object DNS eq domain
access-list DMZ_access_in extended permit object-group TCPUDP object obj-192.168.3.0 object-group DM_INLINE_NETWORK_1 object-group rdp
access-list DMZ_access_in extended deny ip any object-group InternalNetworks
access-list DMZ_access_in extended permit tcp object obj-192.168.3.0 object obj_any object-group DM_INLINE_TCP_2
access-list inside_access_in extended permit ip object obj-192.168.2.0 object-group InternalNetworks
access-list inside_access_in extended permit object-group TCPUDP object obj-192.168.2.0 object obj_any object-group rdp
access-list inside_access_in extended permit tcp object obj-192.168.2.0 object obj_any object-group DM_INLINE_TCP_1
access-list inside_access_in extended permit object-group DM_INLINE_SERVICE_1 object Srv2 object obj_any
access-list inside_access_in extended permit object-group TCPUDP object obj-192.168.2.0 object obj-192.168.3.0 object-group rdp
access-list ServerNet1_access_in extended permit object-group DM_INLINE_SERVICE_2 any object DNS
access-list ServerNet1_access_in extended permit ip any any
pager lines 24
logging enable
logging asdm informational
mtu ServerNet1 1500
mtu inside 1500
mtu DMZ 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-711-52.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (any,outside) after-auto source dynamic DEFAULT-PAT-SOURCE interface
access-group ServerNet1_access_in in interface ServerNet1
access-group inside_access_in in interface inside
access-group DMZ_access_in in interface DMZ
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http 192.168.2.0 255.255.255.0 inside
http 192.168.4.0 255.255.255.0 ServerNet1
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
telnet timeout 5
ssh 192.168.4.0 255.255.255.0 ServerNet1
ssh 192.168.2.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous -
VPN Between Cisco ASA 5505 and Cisco Router 881
Hi All,
I want to interconnect two office to each other but i have trouble: Please see below my configuration: What is missing to finalize the configuration properly?
Cisco ASA 5505.
Version 8.4(3)
HQ-ASA5505(config)# crypto ikev1 policy 888
HQ-ASA5505(config-ikev1-policy)# authentication pre-share
HQ-ASA5505(config-ikev1-policy)# encryption 3des
HQ-ASA5505(config-ikev1-policy)# hash md5
HQ-ASA5505(config-ikev1-policy)# lifetime 86400
HQ-ASA5505(config-ikev1-policy)# group 2
HQ-ASA5505(config)# tunnel-group 1.1.1.1 type ipsec-l2l
HQ-ASA5505(config)# tunnel-group 1.1.1.1 ipsec-attributes
HQ-ASA5505(config-tunnel-ipsec)# ikev1 pre-shared-key test
HQ-ASA5505(config)#object network HQ-Users
HQ-ASA5505(config-network-object)#subnet 10.48.0.0 255.255.255.0
HQ-ASA5505(config)# object-group network HQ.grp
HQ-ASA5505(config-network-object-group)# network-object object HQ-Users
HQ-ASA5505(config)#object network FSP_DATA
HQ-ASA5505(config-network-object)#subnet 10.48.12.0 255.255.255.0
HQ-ASA5505(config)#object-group network FSP.grp
HQ-ASA5505(config-network-object-group)#network-object object FSP_DATA
HQ-ASA5505(config)#access-list VPN_to_FSP extended permit ip object-group HQ.grp object-group FSP.grp
HQ-ASA5505(config)# crypto ipsec ikev1 transform-set TS esp-3des esp-md5-hmac
HQ-ASA5505(config)# crypto map ouside_map 888 set ikev1 transform-set TS
HQ-ASA5505(config)# crypto map ouside_map 888 match address VPN_to_FSP
HQ-ASA5505(config)# crypto map ouside_map 888 set peer 1.1.1.1
HQ-ASA5505(config)# crypto map ouside_map 888 set pfs group2
HQ-ASA5505(config)# crypto ikev1 enable outside
HQ-ASA5505(config)# crypto map ouside_map interface outside
Router 881
Version 12.4
License Information for 'c880-data'
License Level: advipservices Type: Permanent
Next reboot license Level: advipservices
LAB_ROuter(config)#object-group network HQ
LAB_ROuter(config-network-group)#10.48.0.0 255.255.255.0
LAB_ROuter(config)#object-group network FSP
LAB_ROuter(config-network-group)#10.48.12.0 255.255.255.0
ip access-list extended FSP_VPN
permit ip object-group FSP object-group HQ
LAB_ROuter(config)#crypto isakmp policy 888
LAB_ROuter(config-isakmp)#encryption 3des
LAB_ROuter(config-isakmp)#authentication pre-share
LAB_ROuter(config-isakmp)#hash md5
LAB_ROuter(config-isakmp)#group 2
LAB_ROuter(config-isakmp)#lifetime 86400
LAB_ROuter(config)#crypto isakmp key test address 2.2.2.2
LAB_ROuter(config)#crypto ipsec transform-set TS esp-3des esp-md5-hmac
crypto map outside_map 888 ipsec-isakmp
set peer 2.2.2.2
set transform-set TS
match address FSP_VPN
interface fast4 --> Outside Interface (where public IP address is assigned)
crypto map outside_map
Thank you in advance for your prompt advice!If you do a show crypto map in the router you will see the VPN traffic to be "any to any".
This is due a known bug on Cisco routers. The router does not support object-groups network for the VPN traffic. Use a regular ACL instead. -
Cisco ASA 5505 Site to site VPN IPSEC tunnel to an Clavister Firewall
Hi,
I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.
When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: show crypto isakmp sa
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.
They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505.
Here is some logs that ASDM give me about the tunnel issue, but like I said, the tunnel is up and only one remote network is reachable in that tunnel.....
3
Nov 21 2012
07:11:09
713902
Group = 195.149.180.254, IP = 195.149.169.254, Removing peer from correlator table failed, no match!
3
Nov 21 2012
07:11:09
713902
Group = 195.149.180.254, IP = 195.149.169.254, QM FSM error (P2 struct &0xc92462d0, mess id 0x1c6bf927)!
3
Nov 21 2012
07:11:09
713061
Group = 195.149.180.254, IP = 195.149.169.254, Rejecting IPSec tunnel: no matching crypto map entry for remote proxy 0.0.0.0/0.0.0.0/0/0 local proxy 0.0.0.0/0.0.0.0/0/0 on interface outside
5
Nov 21 2012
07:11:09
713119
Group = 195.149.180.254, IP = 195.149.169.254, PHASE 1 COMPLETED
Here is from the syntax: show crypto isakmp sa
Result of the command: "show crypto isakmp sa"
Active SA: 1
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
1 IKE Peer: 195.149.180.254
Type : L2L Role : responder
Rekey : no State : MM_ACTIVE
Result of the command: "show crypto ipsec sa"
interface: outside
Crypto map tag: CustomerCryptoMap, seq num: 10, local addr: 213.180.90.29
access-list arvika_garnisonen permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
local ident (addr/mask/prot/port): (172.22.65.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.123.0/255.255.255.0/0/0)
current_peer:195.149.180.254
#pkts encaps: 2188, #pkts encrypt: 2188, #pkts digest: 2188
#pkts decaps: 2082, #pkts decrypt: 2082, #pkts verify: 2082
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 2188, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 213.180.67.29, remote crypto endpt.: 195.149.180.254
path mtu 1500, ipsec overhead 74, media mtu 1500
current outbound spi: E715B315
inbound esp sas:
spi: 0xFAC769EB (4207372779)
transform: esp-aes-256 esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 5, }
slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
sa timing: remaining key lifetime (kB/sec): (38738/2061)
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0xFFFFFFFF 0xFFFFFFFF
outbound esp sas:
spi: 0xE715B315 (3876958997)
transform: esp-aes-256 esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 5, }
slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
sa timing: remaining key lifetime (kB/sec): (38673/2061)
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
And here are my Accesslists and vpn site to site config:
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 84600
crypto isakmp nat-traversal 40
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map CustomerCryptoMap 10 match address VPN_Tunnel
crypto map CustomerCryptoMap 10 set pfs group5
crypto map CustomerCryptoMap 10 set peer 195.149.180.254
crypto map CustomerCryptoMap 10 set transform-set ESP-AES-256-SHA
crypto map CustomerCryptoMap interface outside
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0 -------> This is the only remote network I can reach behind the Cisco ASA and the other remote networks dont work..
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
nat (inside) 0 access-list nonat
All these remote networks are at the Main Site Clavister Firewall.
Best Regards
MichaelHi,
I'd start by getting the configuration of the remote site related to Local/Remote network configurations and go through them. Even though no changes have been made.
If they are mirror images of eachother already I'd say its probably some problem related to Cisco/Clavister setup
Seems especially wierd to me that one of the error messages includes 0.0.0.0 lines.
I have run into some problems with L2L VPN configurations when our Cisco device just doesnt want to work with the remote end device. In some cases we have confirmed that our networks defined for the L2L VPN are exactly the same and yet when checking debugs on the ASA side we can see the remote end device using totally wrong network masks for the VPN negotiaton and therefore it failed. That problem we corrected with changing the network masks a bit.
Maybe you could try to change the Encryption Domain configurations a bit and test it then.
You could also maybe take some debugs on the Phase2 and see if you get anymore hints as to what could be the problem when only one network is working for the L2L VPN.
- Jouni -
Site to site VPN between cisco asa 5550 and checkpoint r75
Hi all ,
below is cisco asa config for our customer end:
crypto ipsec transform-set chello-transform esp-aes-256 esp-sha-hmac
crypto ipsec security-association lifetime seconds 3600
crypto ipsec security-association lifetime kilobytes 4608000
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
What should i configure on checkpoint for first phase and second phase ?
Regards,
SuhailIn checkpoint VPN community, default setting for phase 1 is 86400 seconds so you're good there. Phase II default is 28,800 so you need to edit the parameter and change it to 3600. the rest is the same as cisco with the exception of the lifetime in kilobytes which CP does not have
Easy right? -
Two Cisco ASA 5505, IPSec Multiple Subnets, Problem with Phase2, DSL
Hi all.
we have following IPSec configuration:
ASA Site 1:
Cisco Adaptive Security Appliance Software Version 9.1(1)
crypto ipsec ikev1 transform-set TSAES esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TSMD5 esp-3des esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal PropAES256
access-list SITE_2 extended permit ip 172.27.0.0 255.255.0.0 172.27.97.0 255.255.255.0
access-list SITE_2 extended permit ip 172.28.60.0 255.255.254.0 172.27.97.0 255.255.255.0
access-list SITE_2 extended permit ip 172.22.0.0 255.255.0.0 172.27.97.0 255.255.255.0
access-list SITE_2 extended permit ip 172.27.0.0 255.255.0.0 172.27.99.0 255.255.255.0
access-list SITE_2 extended permit ip 172.22.0.0 255.255.0.0 172.27.99.0 255.255.255.0
crypto map CMVPN 5 match address SITE_2
crypto map CMVPN 5 set peer IP_SITE2
crypto map CMVPN 5 set ikev2 ipsec-proposal PropAES256
crypto map CMVPN interface OUTSIDE
route OUTSIDE 172.27.97.0 255.255.255.0 citic-internet-gw 255
route OUTSIDE 172.27.99.0 255.255.255.0 citic-internet-gw 255
tunnel-group IP_SITE2 type ipsec-l2l
tunnel-group IP_SITE2 general-attributes
default-group-policy VPN_S2S_WAN
tunnel-group IP_SITE2 ipsec-attributes
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
ASA Site 2:
Cisco Adaptive Security Appliance Software Version 9.1(4)
access-list SITE_1 extended permit ip 172.27.97.0 255.255.255.0 172.28.60.0 255.255.254.0
access-list SITE_1 extended permit ip 172.27.97.0 255.255.255.0 172.27.0.0 255.255.0.0
access-list SITE_1 extended permit ip 172.27.97.0 255.255.255.0 172.22.0.0 255.255.0.0
access-list SITE_1 extended permit ip 172.27.99.0 255.255.255.0 172.27.0.0 255.255.0.0
access-list SITE_1 extended permit ip 172.27.99.0 255.255.255.0 172.22.0.0 255.255.0.0
crypto map CMVPN 10 match address SITE_1
crypto map CMVPN 10 match address SITE_1
crypto map CMVPN 10 set peer IP_SITE1
crypto map CMVPN 10 set ikev2 ipsec-proposal IKEV2AES
crypto map CMVPN 10 set reverse-route
crypto map CMVPN interface OUTSIDE
tunnel-group IP_SITE1 type ipsec-l2l
tunnel-group IP_SITE1 general-attributes
default-group-policy VPN_S2S_WAN
tunnel-group IP_SITE1 ipsec-attributes
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
We are not able to reach from 172.22.20.x ips 172.27.99.x.
It seems so that the phase2 for this subnet is missing…...... as long as we try to reach from 172.27.99.x any ip in 172.22.20.x.
We are using similar configuration on many sites and it works correctly expect sites with DSL line.
We can exclude problem with NAT,ACL or routing. The connection is working fine as long as “we open all phase 2 manually” . After re-open (idle timeout) the tunnel the problem comes back.
Thanks in advance for your help.
Regards.
Jan
ASA Site 1# sh vpn-sessiondb detail l2l filter ipaddress ASA Site 2
Session Type: LAN-to-LAN Detailed
Connection : IP ASA Site 2
Index : 3058 IP Addr : IP ASA Site 2
Protocol : IKEv2 IPsec
Encryption : IKEv2: (1)AES256 IPsec: (3)AES256
Hashing : IKEv2: (1)SHA512 IPsec: (3)SHA1
Bytes Tx : 423634 Bytes Rx : 450526
Login Time : 19:59:35 HKT Tue Apr 29 2014
Duration : 1h:50m:45s
IKEv2 Tunnels: 1
IPsec Tunnels: 3
IKEv2:
Tunnel ID : 3058.1
UDP Src Port : 500 UDP Dst Port : 500
Rem Auth Mode: preSharedKeys
Loc Auth Mode: preSharedKeys
Encryption : AES256 Hashing : SHA512
Rekey Int (T): 86400 Seconds Rekey Left(T): 79756 Seconds
PRF : SHA512 D/H Group : 5
Filter Name :
IPv6 Filter :
IPsec:
Tunnel ID : 3058.2
Local Addr : 172.22.0.0/255.255.0.0/0/0
Remote Addr : 172.27.97.0/255.255.255.0/0/0
Encryption : AES256 Hashing : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds Rekey Left(T): 22156 Seconds
Rekey Int (D): 4608000 K-Bytes Rekey Left(D): 4607648 K-Bytes
Idle Time Out: 25 Minutes Idle TO Left : 24 Minutes
Bytes Tx : 312546 Bytes Rx : 361444
Pkts Tx : 3745 Pkts Rx : 3785
IPsec:
Tunnel ID : 3058.3
Local Addr : 172.27.0.0/255.255.0.0/0/0
Remote Addr : 172.27.97.0/255.255.255.0/0/0
Encryption : AES256 Hashing : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds Rekey Left(T): 22165 Seconds
Rekey Int (D): 4608000 K-Bytes Rekey Left(D): 4607952 K-Bytes
Idle Time Out: 25 Minutes Idle TO Left : 24 Minutes
Bytes Tx : 50014 Bytes Rx : 44621
Pkts Tx : 496 Pkts Rx : 503
IPsec:
Tunnel ID : 3058.4
Local Addr : 172.27.0.0/255.255.0.0/0/0
Remote Addr : 172.27.99.0/255.255.255.0/0/0
Encryption : AES256 Hashing : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds Rekey Left(T): 22324 Seconds
Rekey Int (D): 4608000 K-Bytes Rekey Left(D): 4607941 K-Bytes
Idle Time Out: 25 Minutes Idle TO Left : 24 Minutes
Bytes Tx : 61074 Bytes Rx : 44461
Pkts Tx : 402 Pkts Rx : 437
NAC:
Reval Int (T): 0 Seconds Reval Left(T): 0 Seconds
SQ Int (T) : 0 Seconds EoU Age(T) : 6648 Seconds
Hold Left (T): 0 Seconds Posture Token:
Redirect URL :
.... after ping from 172.27.99.x any ip in 172.22.20.x.
ASA Site 1# sh vpn-sessiondb detail l2l filter ipaddress ASA Site 2
Session Type: LAN-to-LAN Detailed
Connection : IP ASA Site 2
Index : 3058 IP Addr : IP ASA Site 2
Protocol : IKEv2 IPsec
Encryption : IKEv2: (1)AES256 IPsec: (4)AES256
Hashing : IKEv2: (1)SHA512 IPsec: (4)SHA1
Bytes Tx : 784455 Bytes Rx : 1808965
Login Time : 19:59:35 HKT Tue Apr 29 2014
Duration : 2h:10m:48s
IKEv2 Tunnels: 1
IPsec Tunnels: 4
IKEv2:
Tunnel ID : 3058.1
UDP Src Port : 500 UDP Dst Port : 500
Rem Auth Mode: preSharedKeys
Loc Auth Mode: preSharedKeys
Encryption : AES256 Hashing : SHA512
Rekey Int (T): 86400 Seconds Rekey Left(T): 78553 Seconds
PRF : SHA512 D/H Group : 5
Filter Name :
IPv6 Filter :
IPsec:
Tunnel ID : 3058.2
Local Addr : 172.22.0.0/255.255.0.0/0/0
Remote Addr : 172.27.97.0/255.255.255.0/0/0
Encryption : AES256 Hashing : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds Rekey Left(T): 20953 Seconds
Rekey Int (D): 4608000 K-Bytes Rekey Left(D): 4606335 K-Bytes
Idle Time Out: 25 Minutes Idle TO Left : 24 Minutes
Bytes Tx : 652492 Bytes Rx : 1705136
Pkts Tx : 7419 Pkts Rx : 7611
IPsec:
Tunnel ID : 3058.3
Local Addr : 172.27.0.0/255.255.0.0/0/0
Remote Addr : 172.27.97.0/255.255.255.0/0/0
Encryption : AES256 Hashing : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds Rekey Left(T): 20962 Seconds
Rekey Int (D): 4608000 K-Bytes Rekey Left(D): 4607942 K-Bytes
Idle Time Out: 25 Minutes Idle TO Left : 24 Minutes
Bytes Tx : 60128 Bytes Rx : 52359
Pkts Tx : 587 Pkts Rx : 594
IPsec:
Tunnel ID : 3058.4
Local Addr : 172.27.0.0/255.255.0.0/0/0
Remote Addr : 172.27.99.0/255.255.255.0/0/0
Encryption : AES256 Hashing : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds Rekey Left(T): 21121 Seconds
Rekey Int (D): 4608000 K-Bytes Rekey Left(D): 4607931 K-Bytes
Idle Time Out: 25 Minutes Idle TO Left : 24 Minutes
Bytes Tx : 70949 Bytes Rx : 50684
Pkts Tx : 475 Pkts Rx : 514
IPsec:
Tunnel ID : 3058.5
Local Addr : 172.22.0.0/255.255.0.0/0/0
Remote Addr : 172.27.99.0/255.255.255.0/0/0
Encryption : AES256 Hashing : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds Rekey Left(T): 28767 Seconds
Rekey Int (D): 4608000 K-Bytes Rekey Left(D): 4608000 K-Bytes
Idle Time Out: 25 Minutes Idle TO Left : 24 Minutes
Bytes Tx : 961 Bytes Rx : 871
Pkts Tx : 17 Pkts Rx : 14
NAC:
Reval Int (T): 0 Seconds Reval Left(T): 0 Seconds
SQ Int (T) : 0 Seconds EoU Age(T) : 7852 Seconds
Hold Left (T): 0 Seconds Posture Token:
Redirect URL :Hi,
on 212 is see
tunnel-group 195.xxx.xxx.xxx type ipsec-l2l
tunnel-group 195.xxx.xxx.xxx ipsec-attributes
pre-shared-key
When you define the peer with static tunnel-group entry ASA is looking for peer configuration in static crypto map. If the peer is behind static NAT configure a proper static crypto map with matching acl and proposals.
If the peer is behind dynamic nat refer this example :http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/81883-ipsec-iosrtr-dyn-pix-nat.html
Regards,
Abaji. -
Cisco ASA 5505 IPSEC, one endpoint behind NAT device
We have two Cisco ASA 5505 devices.
Both are identical, however, one of them is behind a NAT device.
We are attempting to create an IPSEC network.
Site fg:
<ipsec subnet1> -- ASA 5505 (ASA1) -- <internet>
ASA1: 10.1.1.2/24 (inside), 212.xxx.xxx.xxx/28 (outside)
Site be:
<ipsec_subnet2> -- ASA 5505 (ASA3) -- Zywall USG (USG1) -- <internet>
ASA3: 10.1.4.1/24 (inside), 192.168.4.50/24 (outside)
USG1: 192.168.4.100/24 (inside), 195.xxx.xxx.xxx/30 (outside)
USG1: UDP port 500/4500 forwarded to 192.168.4.50
It seems that ASA1 stops the procedure (we verified this with debug crypto isakmp 254):
Group = 195.xxx.xxx.xxx, IP = 195.xxx.xxx.xxx, QM FSM error (P2 struct &0xd1111cd8, mess id 0x81111a78)!
Group = 195.xxx.xxx.xxx, IP = 195.xxx.xxx.xxx, Rejecting IPSec tunnel: no matching crypto map entry for remote proxy 192.168.4.50/255.255.255.255/0/0 local proxy 212.xxx.xxx.xxx/255.255.255.255/0/0 on interface outside
Group = 195.xxx.xxx.xxx, IP = 195.xxx.xxx.xxx, PHASE 1 COMPLETED
We verified / attempted the following:
- NAT excemption on both sides for IPSEC subnets
- Mirror image crypto maps
- Disabled IKE peer ID validation (yes, pre-shared key but we ran out of ideas)
- Toggled between static to dynamic crypto maps on ASA1
Most search results turned up results referring to the incorrect settings of the crypto map or the lack of NAT excemption.
Does anyone have any idea?
195.txt contains show running-config of ASA3
212.txt contains show running-config of ASA1
log.txt contains somewhat entire log snipper of ASA1Hi,
on 212 is see
tunnel-group 195.xxx.xxx.xxx type ipsec-l2l
tunnel-group 195.xxx.xxx.xxx ipsec-attributes
pre-shared-key
When you define the peer with static tunnel-group entry ASA is looking for peer configuration in static crypto map. If the peer is behind static NAT configure a proper static crypto map with matching acl and proposals.
If the peer is behind dynamic nat refer this example :http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/81883-ipsec-iosrtr-dyn-pix-nat.html
Regards,
Abaji.
Maybe you are looking for
-
ORA-01006: bind variable does not exist
Plz, if any body is able to handle this tell me the solution SELECT job_ticket_mst.N_LINENUMB, job_ticket_mst.V_CVDPL_NO, JOB_TICKET_MST.V_STAMP,Common_mst.V_DESCRIPTION, JOB_TICKET_MST.D_JOB_DATE, JOB_TICKET_MST.V_JOB_TYPE_CODE, JOB_TICKET_MST.V_CUS
-
Hi , If i want to find out the planning file entry for the materil , how can i find out ? please give me the table name . Transaction code i knoe MD21 , MDre & MDAB , i want to see it on table lavel . In which table i will get this information . Plea
-
Restore iTunes on a New Computer
I apologize if this has been asked before, but I don't have time to search all the questions. I just found out my office was getting me a new PC (good thing, but bad for the idiot that downloads all their music at work!!!) and that my software would
-
I can't open a 32-bit HDR file made with Photoshop HDR in Lightroom.
I can't open a 32-bit HDR file made with Photoshop HDR. I saved the file in Photoshop with the maximum compatibility-option on. In Lightroom the file doesn't show a preview and an exclamation mark in the upper right corner. Anybody an idea why and ho
-
hi gurus,can anybody help me by providing the necessary step by step procedure of vendor evaluation cycle.it s urgent. please help me out regards, atanu