Cisco ASA SNMP OIDs (show name, show vpn-sessiondb l2l)

Hi all,
I am trying to figure out the SNMP OIDs that is equivalent to the following ASA commands:
show name
show vpn-sessiondb l2l
Thanks!

im looking for the solution ? did u ever find out if this was possible?

Similar Messages

  • Cisco ASA 5505 Remote Access IP/Sec VPN Connectivity Issues

    We have a Cisco ASA that we use just for Remote Access VPN. It uses UDP and was working fine for about 2 months. Recently clients have had intermittent issues when connecting from home. The following message is display by the Cisco VPN Client :
    "Secure VPN connection terminated locally by the Client. Reason 412: The remote peer is no longer responding"
    Upon looking at a client side packet capture, I notice that no response is being given back to the client for the udp packets sent to the ASA on udp 500. If I login to the ASA from the LAN and send a single ping FROM the ASA, then the client can connect without issue. I don't understand the significance of the needed outbound ping since ping is not used by the client to test if the ASA is alive.
    Once again this is a remote access udp ip/sec VPN. I set most of it up with the VPN wizard and then backed up the config. The issue started happening at least a month after setup (maybe two) and I restored to the saved config just in-case, but the issue remains.
    Any insight would be greatly appreciated.
    I'm using IOS 831 and have tried 821 and 823 as one thread that I found recommended downgraded to 821.
    Thanks much,
    Justin

    Javier,
    I logged into the ASA last time the VPN went down. I issued the following commands:
    debug crypto isakmp 190
    debug crypto ipsec 190
    capture outside-cap interface outside match udp any any
    I then used a remote access tool to access the client and tried to connect. I got absolutely nothing from debugging. So I issued the following command:
    show capture outside | include 500
    and also got nothing. So I issued the following command:
    ping 4.2.2.2
    Upon which my normal deug messaged began to showup, so I issued the show capture outside command again and recieved the expected output below:
       1: 15:44:18.570160 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 868
       2: 15:44:18.579269 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151:  udp 444
       3: 15:44:18.703866 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 172
       4: 15:44:18.706567 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151:  udp 76
       5: 15:44:18.831499 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 92
       6: 15:44:19.024061 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151:  udp 76
       7: 15:44:19.111963 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 60
       8: 15:44:19.517185 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 204
       9: 15:44:19.521350 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 92
      10: 15:44:19.522723 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151:  udp 252
      11: 15:44:42.121957 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 868
      12: 15:44:42.130822 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 444
      13: 15:44:42.228397 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 172
      14: 15:44:42.231036 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 76
      15: 15:44:42.329557 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 92
      16: 15:44:42.521091 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 76
      17: 15:44:42.610167 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 60
      18: 15:44:42.649258 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 204
      19: 15:44:42.653790 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 252
      20: 15:44:42.789342 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 1036
      21: 15:44:42.792119 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 92
      22: 15:44:42.800846 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 188
      23: 15:44:42.892120 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 60
      34: 15:44:54.446220 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 92
      35: 15:44:54.447913 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 92
      70: 15:45:01.825000 802.1Q vlan#2 P0 OFFICE_IP.10000 > REMOTE_IP.10000:  udp 100
    174: 15:45:03.417764 802.1Q vlan#2 P0 OFFICE_IP.10000 > REMOTE_IP.10000:  udp 500
    377: 15:45:07.881500 802.1Q vlan#2 P0 REMOTE_IP.10000 > OFFICE_IP.10000:  udp 100    1: 15:44:18.570160 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 868
       2: 15:44:18.579269 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151:  udp 444
       3: 15:44:18.703866 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 172
       4: 15:44:18.706567 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151:  udp 76
       5: 15:44:18.831499 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 92
       6: 15:44:19.024061 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151:  udp 76
       7: 15:44:19.111963 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 60
       8: 15:44:19.517185 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 204
       9: 15:44:19.521350 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500:  udp 92
      10: 15:44:19.522723 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151:  udp 252
      11: 15:44:42.121957 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 868
      12: 15:44:42.130822 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 444
      13: 15:44:42.228397 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 172
      14: 15:44:42.231036 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 76
      15: 15:44:42.329557 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 92
      16: 15:44:42.521091 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 76
      17: 15:44:42.610167 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 60
      18: 15:44:42.649258 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 204
      19: 15:44:42.653790 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 252
      20: 15:44:42.789342 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 1036
      21: 15:44:42.792119 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 92
      22: 15:44:42.800846 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 188
      23: 15:44:42.892120 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 60
      34: 15:44:54.446220 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500:  udp 92
      35: 15:44:54.447913 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155:  udp 92
      70: 15:45:01.825000 802.1Q vlan#2 P0 OFFICE_IP.10000 > REMOTE_IP.10000:  udp 100
    174: 15:45:03.417764 802.1Q vlan#2 P0 OFFICE_IP.10000 > REMOTE_IP.10000:  udp 500
    377: 15:45:07.881500 802.1Q vlan#2 P0 REMOTE_IP.10000 > OFFICE_IP.10000:  udp 100
    It would seem as if no traffic reached the ASA until some outbound traffic to an arbitrary public IP. In this case I sent an echo request to a public DNS server. It seems almost like a state-table issue although I don't know how ICMP ties in.
    Once again, any insight would be greatly appreciated.
    Thanks,
    Justin

  • Cisco ASA using Multiple DNS Names

    Hi,
    I am trying to setup a Cisco ASA for SSL vpn; however due to load balancing/traffic redirection performed by a different device; I was wondering if it may be possible perform a certificaate signing request/certificate required for it to have multiple address? An example would be:
    IP: 1.1.1.1, fqdn: vpn1.asa.com
    IP: 1.1.1.2, fqdn: vpn2.asa.com
    IP: 1.1.1.3 fqdn: vpn3.asa.com 
    Not too sure on how to perform the CSR for it on the ASA? Do I create the csr cert with a single cn=vpn1.asa.com and ask the CA vendor to sign it off with SANsof vpn2.asa.com and vpn3.asa.com?
    Client performing ssl vpn on vpn1.asa.com or vpn2.asa.com or vpn3.asa.com  should not be prompted certificate warning.
    Thanks.

    Hi,
    Appreciate the input. For the setup; the different fqdn is used due to different authentications/locations/etc... used. I have further illustrate the setup using the same interface for vpn access:
    vpn3.asa.com (Extranet Vendor Access)--------------------------------|
                                                                                               |
                                                                                              |
                                                                                              |
    vpn1.asa.com (External branch offices)-------------------------------ASA -------------Internal authentication servers
                                                                                               |
                                                                                               |
    vpn2.asa.com(HQ/Corporate Users)-----------------------------------------
    Not too sure for the creation of the CSR with a single cn=vpn1.asa.com and ask the CA vendor to sign  it off with SANs of vpn2.asa.com and vpn3.asa.com as well as vpn1.asa.com?
    Thanks.

  • Doese Cisco ASA 5500 has module increase performance VPN?

    Dear All,
    Doese Cisco ASA 5510 and 5505 has module for increase performance VPN ?
    Best Regards,
    Rechard

    Rechard,
    There is one built into every ASA. If you need better performance because you're limited by engine performance... you need to most likely move up to a bigged model.
    Here is the datasheet for reference:
    http://www.cisco.com/en/US/products/ps6120/prod_models_comparison.html
    M.

  • Cisco ASA 5505 site to site IPSec VPN with RV220W issue

    I have a ASA5505 connected to RV220W through IPSec VPN. When  using SMB to transfer large file, the ASA5505 will show error message:
    CTM ERROR: Invalid input parameters, ctm_get_scb_prot_stats:1561
    The error message from the debug crypto engine. When  the message show, the speed of the transfer will slow down quickly, and  even no data can be go through between ASA and the RV220W. But the IPSec  SA and the IKE SA is active, and can ping the inside network in both  site.
    Both ASA5505 and the RV220W has been updated the latest firmware. I have surf the Google but no such related issue found.
    Any suggestions on where to look would be much appreciated.
    Thanks in advance
    Terry

    Hi Ted thanks for your reply and information.
    The strange things happened in RV220W shows the IPSec sa is expired, but the ASA5505 IPSec and IKEv1 sa is active. Inside both site internal network can ping to other side, but cant transfer file through Windows SMB. It seems when I transfer over 4GBytes of file, it will start happening and required clear IPSec and IKEv1 sa so that the VPN tunnel will start up again.
    I am already surrander for this issue......

  • Cisco asa- vpn established but cant ping

    I am using 2 cisco asa 5505 routers, i have established vpn between them but i cant ping client internal or outside interface, client can ping my outside interface. Only configuration on client is basic easy vpn settings and interfaces, here is server part configuration on my side:
    ASA Version 9.1(1)
    hostname ciscoasa
    enable password NuLKvvWGg.x9HEKO encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    nameif inside
    security-level 100
    ip address 10.1.2.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    pppoe client vpdn group iskon
    ip address pppoe setroute
    ftp mode passive
    object network obj_any
    subnet 0.0.0.0 0.0.0.0
    object network inside
    subnet 10.1.2.0 255.255.255.0
    object network outside
    subnet 10.1.3.0 255.255.255.0
    object-group protocol DM_INLINE_PROTOCOL_1
    protocol-object ip
    protocol-object icmp
    protocol-object udp
    protocol-object tcp
    object-group protocol DM_INLINE_PROTOCOL_2
    protocol-object ip
    protocol-object icmp
    protocol-object udp
    protocol-object tcp
    access-list 101 extended permit object-group DM_INLINE_PROTOCOL_1 10.1.2.0 255.255.255.0 10.1.3.0 255.255.255.0
    access-list 102 extended permit object-group DM_INLINE_PROTOCOL_2 10.1.3.0 255.255.255.0 10.1.2.0 255.255.255.0
    access-list global_access extended permit ip any any
    pager lines 24
    logging enable
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    icmp unreachable rate-limit 1 burst-size 1
    icmp permit 10.1.3.0 255.255.255.0 echo-reply inside
    icmp permit any inside
    icmp permit any outside
    icmp permit 10.1.3.0 255.255.255.0 echo-reply outside
    no asdm history enable
    arp timeout 14400
    no arp permit-nonconnected
    nat (any,any) source static outside outside destination static inside inside no-proxy-arp
    object network obj_any
    nat (inside,outside) dynamic interface
    access-group global_access global
    route inside 0.0.0.0 0.0.0.0 10.1.3.1 tunneled
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    http server enable
    http 10.1.2.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    crypto ipsec ikev1 transform-set mySET esp-3des esp-md5-hmac
    crypto ipsec security-association pmtu-aging infinite
    crypto dynamic-map DYN-MAP 5 set ikev1 transform-set mySET
    crypto map MAP 60 ipsec-isakmp dynamic DYN-MAP
    crypto map MAP interface outside
    crypto ca trustpool policy
    crypto ikev1 enable outside
    crypto ikev1 policy 1
    authentication pre-share
    encryption des
    hash md5
    group 2
    lifetime 86400
    crypto ikev1 policy 65535
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    management-access inside
    vpdn group iskon request dialout pppoe
    vpdn group iskon localname *********
    vpdn group iskon ppp authentication pap
    vpdn username ***** password *****
    dhcpd auto_config outside
    dhcpd address 10.1.2.5-10.1.2.132 inside
    dhcpd enable inside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    group-policy VPN internal
    group-policy VPN attributes
    split-tunnel-policy tunnelall
    split-tunnel-network-list value 101
    nem enable
    username user password enq05bKrudsJMMBu encrypted privilege 15
    username user attributes
    vpn-group-policy VPN
    vpn-session-timeout none
    group-lock value VPN-TUNNEL
    tunnel-group VPN-TUNNEL type remote-access
    tunnel-group VPN-TUNNEL general-attributes
    default-group-policy VPN
    tunnel-group VPN-TUNNEL ipsec-attributes
    ikev1 pre-shared-key *****
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    Cryptochecksum:3f2923b78a04ee8cfe9324e3e2733d78

    SOLVED!!! i just needed to configure nat here is configuration for any1 with same problem
    : Saved
    ASA Version 9.1(1)
    hostname ciscoasa
    enable password NuLKvvWGg.x9HEKO encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    nameif inside
    security-level 100
    ip address 10.1.2.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    pppoe client vpdn group iskon
    ip address pppoe setroute
    ftp mode passive
    object network obj_any
    subnet 0.0.0.0 0.0.0.0
    object network ladimirevci
    subnet 10.1.2.0 255.255.255.0
    object network lekenik
    subnet 10.1.3.0 255.255.255.0
    access-list 101 extended permit ip 10.1.2.0 255.255.255.0 10.1.3.0 255.255.255.0
    access-list 101 extended permit ip object lekenik object ladimirevci
    access-list 101 extended permit ip object ladimirevci object lekenik
    access-list outside_access_in extended permit ip object ladimirevci object lekenik
    access-list outside_access_in extended permit ip object lekenik object ladimirevci
    access-list outside_access_in extended permit ip any any
    access-list inside_access_in extended permit ip object ladimirevci object lekenik
    access-list inside_access_in extended permit ip object lekenik object ladimirevci
    access-list inside_access_in extended permit ip any any
    access-list nonat extended permit ip 10.1.2.0 255.255.255.0 10.1.3.0 255.255.255.0
    access-list 102 extended permit ip 10.1.3.0 255.255.255.0 10.1.2.0 255.255.255.0
    access-list global_access extended permit ip object lekenik object ladimirevci
    access-list global_access extended permit ip object ladimirevci object lekenik
    access-list global_access extended permit ip any any
    pager lines 24
    logging enable
    logging buffered debugging
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    icmp unreachable rate-limit 1 burst-size 1
    icmp permit any inside
    icmp permit any echo-reply outside
    asdm image disk0:/asdm-712.bin
    no asdm history enable
    arp timeout 14400
    no arp permit-nonconnected
    nat (any,any) source static ladimirevci ladimirevci destination static lekenik lekenik
    object network obj_any
    nat (inside,outside) dynamic interface dns
    access-group inside_access_in in interface inside
    access-group outside_access_in in interface outside
    access-group global_access global
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    http server enable
    http 0.0.0.0 0.0.0.0 inside
    http 10.1.2.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    no sysopt connection permit-vpn
    crypto ipsec ikev1 transform-set mySET esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec security-association pmtu-aging infinite
    crypto dynamic-map DYN-MAP 5 set pfs
    crypto dynamic-map DYN-MAP 5 set ikev1 transform-set mySET
    crypto dynamic-map DYN-MAP 5 set reverse-route
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set reverse-route
    crypto map MAP 60 ipsec-isakmp dynamic DYN-MAP
    crypto map MAP interface outside
    crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map inside_map interface inside
    crypto ca trustpool policy
    crypto ikev1 enable inside
    crypto ikev1 enable outside
    crypto ikev1 policy 1
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 65535
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet 0.0.0.0 0.0.0.0 inside
    telnet timeout 5
    ssh scopy enable
    ssh 0.0.0.0 0.0.0.0 inside
    ssh timeout 60
    console timeout 0
    management-access inside
    vpdn group iskon request dialout pppoe
    vpdn group iskon localname vivaindo@iskon-dsl
    vpdn group iskon ppp authentication pap
    vpdn username vivaindo@iskon-dsl password *****
    dhcpd auto_config outside
    dhcpd address 10.1.2.5-10.1.2.36 inside
    dhcpd enable inside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    ssl encryption rc4-md5 rc4-sha1 aes128-sha1 aes256-sha1 3des-sha1
    group-policy DfltGrpPolicy attributes
    vpn-tunnel-protocol ikev2 ssl-clientless
    group-policy VPN internal
    group-policy VPN attributes
    vpn-tunnel-protocol ikev1 l2tp-ipsec
    group-lock value VPN-TUNNEL
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value 101
    nem enable
    username user password enq05bKrudsJMMBu encrypted privilege 15
    username user attributes
    vpn-group-policy VPN
    group-lock value VPN-TUNNEL
    tunnel-group VPN-TUNNEL type remote-access
    tunnel-group VPN-TUNNEL general-attributes
    default-group-policy VPN
    tunnel-group VPN-TUNNEL ipsec-attributes
    ikev1 pre-shared-key *****
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny 
      inspect sunrpc
      inspect xdmcp
      inspect sip 
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    Cryptochecksum:ddac35422ebbf57095be7a1d33b0b67d
    : end
    asdm image disk0:/asdm-712.bin
    no asdm history enable

  • Cisco ASA 5505 VPN Routing/Networking Question

    I have a very basic question about Cisco ASA 5505 IPsec Site to Site VPNs.  I want to install a Cisco ASA 5505 at a Data Center, in a LAN subnet that utilizes publicly routable IP addresses.  I would like to install a second Cisco ASA 5505 in a remote branch office as its peer. 
    Regardless of whether I use publicly routable IPs at the branch office in the "inside" network or non-routable IPs, how would the devices and servers at the Data Center know to route IP packets destined for the branch office back through the Cisco ASA instead of through the default gateway at the Data Center?  I can see accomplishing this if every single device at the Data Center is configured with routing table entries, but that isn't feasible.  It also isn't feasible to use the Cisco ASA 5505 as the default gateway for all of the devices as the Data Center, allowing it to decide where the traffic should go.
    What am I missing?  Is the solution to try to map branch office IPs to IP addresses within the Data Center's LAN subnet so that all of the traffic is on the same subnet?

    You can do it in several different ways.
    One way is to tell the server that if it has traffic to network x then it needs to go to the ASA all other traffic is to head for the default gateway.
    In windows this is done via the route command
    do not forget to make it "persistent" otherwise the route will disapear when your reboot the server.
    in unix/linux
    It is also the route command
    Or you can tell your "default gateway" to route that network to the ASA
    Good luck
    HTH

  • A possible bug related to the Cisco ASA "show access-list"?

    We encountered a strange problem in our ASA configuration.
    In the "show running-config":
    access-list inside_access_in remark CM000067 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:http_access
    access-list inside_access_in remark CM000458 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:https_access
    access-list inside_access_in remark test 11111111111111111111111111 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security
    access-list inside_access_in extended permit tcp host 1.1.1.1 host 192.168.20.86 eq 81 log
    access-list inside_access_in remark CM000260 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:netbios-dgm
    access-list inside_access_in remark CM006598 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:netbios-ns
    access-list inside_access_in remark CM000220 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:netbios-ssn
    access-list inside_access_in remark CM000223 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:tcp/445
    access-list inside_access_in extended permit tcp 172.31.254.0 255.255.255.0 any eq www log
    access-list inside_access_in extended permit tcp 172.31.254.0 255.255.255.0 any eq https log
    access-list inside_access_in extended permit udp 172.31.254.0 255.255.255.0 any eq netbios-dgm log
    access-list inside_access_in extended permit udp 172.31.254.0 255.255.255.0 any eq netbios-ns log
    access-list inside_access_in extended permit tcp 172.31.254.0 255.255.255.0 any eq netbios-ssn log
    access-list inside_access_in extended permit tcp 172.31.254.0 255.255.255.0 any eq 445 log
    access-list inside_access_in remark CM000280 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:domain
    access-list inside_access_in extended permit tcp object 172.31.254.2 any eq domain log
    access-list inside_access_in extended permit udp object 172.31.254.2 any eq domain log
    access-list inside_access_in remark CM000220 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:catch_all
    access-list inside_access_in extended permit ip object 172.31.254.2 any log
    access-list inside_access_in remark CM0000086 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:SSH_internal
    access-list inside_access_in extended permit tcp 172.31.254.0 255.255.255.0 interface inside eq ssh log
    access-list inside_access_in remark CM0000011 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:PortRange
    access-list inside_access_in extended permit object TCPPortRange 172.31.254.0 255.255.255.0 host 192.168.20.91 log
    access-list inside_access_in remark CM0000012 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:FTP
    access-list inside_access_in extended permit tcp object inside_range range 1024 45000 host 192.168.20.91 eq ftp log
    access-list inside_access_in remark CM0000088 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:PortRange
    access-list inside_access_in extended permit ip 192.168.20.0 255.255.255.0 any log
    access-list inside_access_in remark CM0000014 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:DropIP
    access-list inside_access_in extended permit ip object windowsusageVM any log
    access-list inside_access_in extended permit ip any object testCSM-object
    access-list inside_access_in extended permit ip 172.31.254.0 255.255.255.0 any log
    access-list inside_access_in remark CM0000065 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:IP
    access-list inside_access_in extended permit ip host 172.31.254.2 any log
    access-list inside_access_in remark CM0000658 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security
    access-list inside_access_in extended permit tcp host 192.168.20.95 any eq www log
    In the "show access-list":
    access-list inside_access_in line 1 remark CM000067 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:http_access
    access-list inside_access_in line 2 remark CM000458 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:https_access
    access-list inside_access_in line 3 remark test 11111111111111111111111111 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security
    access-list inside_access_in line 4 extended permit tcp host 1.1.1.1 host 192.168.20.86 eq 81 log informational interval 300 (hitcnt=0) 0x0a                                                           3bacc1
    access-list inside_access_in line 5 remark CM000260 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:netbios-dgm
    access-list inside_access_in line 6 remark CM006598 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:netbios-ns
    access-list inside_access_in line 7 remark CM000220 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:netbios-ssn
    access-list inside_access_in line 8 remark CM000223 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:tcp/445
    access-list inside_access_in line 9 extended permit tcp 172.31.254.0 255.255.255.0 any eq www log informational interval 300 (hitcnt=0) 0x06                                                           85254a
    access-list inside_access_in line 10 extended permit tcp 172.31.254.0 255.255.255.0 any eq https log informational interval 300 (hitcnt=0) 0                                                           x7e7ca5a7
    access-list inside_access_in line 11 extended permit udp 172.31.254.0 255.255.255.0 any eq netbios-dgm log informational interval 300 (hitcn                                                           t=0) 0x02a111af
    access-list inside_access_in line 12 extended permit udp 172.31.254.0 255.255.255.0 any eq netbios-ns log informational interval 300 (hitcnt                                                           =0) 0x19244261
    access-list inside_access_in line 13 extended permit tcp 172.31.254.0 255.255.255.0 any eq netbios-ssn log informational interval 300 (hitcn                                                           t=0) 0x0dbff051
    access-list inside_access_in line 14 extended permit tcp 172.31.254.0 255.255.255.0 any eq 445 log informational interval 300 (hitcnt=0) 0x7                                                           b798b0e
    access-list inside_access_in line 15 remark CM000280 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:domain
    access-list inside_access_in line 16 extended permit tcp object 172.31.254.2 any eq domain log informational interval 300 (hitcnt=0) 0x6c416                                                           81b
      access-list inside_access_in line 16 extended permit tcp host 172.31.254.2 any eq domain log informational interval 300 (hitcnt=0) 0x6c416                                                           81b
    access-list inside_access_in line 17 extended permit udp object 172.31.254.2 any eq domain log informational interval 300 (hitcnt=0) 0xc53bf                                                           227
      access-list inside_access_in line 17 extended permit udp host 172.31.254.2 any eq domain log informational interval 300 (hitcnt=0) 0xc53bf                                                           227
    access-list inside_access_in line 18 remark CM000220 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:catch_all
    access-list inside_access_in line 19 extended permit ip object 172.31.254.2 any log informational interval 300 (hitcnt=0) 0xd063707c
      access-list inside_access_in line 19 extended permit ip host 172.31.254.2 any log informational interval 300 (hitcnt=0) 0xd063707c
    access-list inside_access_in line 20 remark CM0000086 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:SSH_internal
    access-list inside_access_in line 21 extended permit tcp 172.31.254.0 255.255.255.0 interface inside eq ssh log informational interval 300 (hitcnt=0) 0x4951b794
    access-list inside_access_in line 22 remark CM0000011 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:PortRange
    access-list inside_access_in line 23 extended permit object TCPPortRange 172.31.254.0 255.255.255.0 host 192.168.20.91 log informational interval 300 (hitcnt=0) 0x441e6d68
      access-list inside_access_in line 23 extended permit tcp 172.31.254.0 255.255.255.0 host 192.168.20.91 range ftp smtp log informational interval 300 (hitcnt=0) 0x441e6d68
    access-list inside_access_in line 24 remark CM0000012 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:FTP
    access-list inside_access_in line 25 extended permit tcp object inside_range range 1024 45000 host 192.168.20.91 eq ftp log informational interval 300 0xe848acd5
      access-list inside_access_in line 25 extended permit tcp range 12.89.235.2 12.89.235.5 range 1024 45000 host 192.168.20.91 eq ftp log informational interval 300 (hitcnt=0) 0xe848acd5
    access-list inside_access_in line 26 extended permit ip 192.168.20.0 255.255.255.0 any log informational interval 300 (hitcnt=0) 0xb6c1be37
    access-list inside_access_in line 27 remark CM0000014 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:DropIP
    access-list inside_access_in line 28 extended permit ip object windowsusageVM any log informational interval 300 (hitcnt=0) 0x22170368
      access-list inside_access_in line 28 extended permit ip host 172.31.254.250 any log informational interval 300 (hitcnt=0) 0x22170368
    access-list inside_access_in line 29 extended permit ip any object testCSM-object (hitcnt=0) 0xa3fcb334
      access-list inside_access_in line 29 extended permit ip any host 255.255.255.255 (hitcnt=0) 0xa3fcb334
    access-list inside_access_in line 30 extended permit ip 172.31.254.0 255.255.255.0 any log informational interval 300 (hitcnt=0) 0xe361b6ed
    access-list inside_access_in line 31 remark CM0000065 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:IP
    access-list inside_access_in line 32 extended permit ip host 172.31.254.2 any log informational interval 300 (hitcnt=0) 0xed7670e1
    access-list inside_access_in line 33 remark CM0000658 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security
    access-list inside_access_in line 34 extended permit tcp host 192.168.20.95 any eq www log informational interval 300 (hitcnt=0) 0x8d07d70b
    There is a comment in the running config: (line 26)
    access-list inside_access_in remark CM0000088 EXP:1/16/2014 OWN:IT_Security BZU:Network_Security JST:PortRange
    This comment is missing in "show access-list". So in the access list, for all the lines after this comment, the line number is no longer correct. This causes problem when we try to use line number to insert a new rule.
    Has anybody seen this problem before? Is this a known problem? I am glad to provide more information if needed.
    Thanks in advance.
    show version:
    Cisco Adaptive Security Appliance Software Version 8.4(4)1
    Device Manager Version 7.1(3)
    Compiled on Thu 14-Jun-12 11:20 by builders
    System image file is "disk0:/asa844-1-k8.bin"
    Config file at boot was "startup-config"
    fmciscoasa up 1 hour 56 mins
    Hardware:   ASA5505, 512 MB RAM, CPU Geode 500 MHz
    Internal ATA Compact Flash, 128MB
    BIOS Flash M50FW016 @ 0xfff00000, 2048KB
    Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
                                 Boot microcode   : CN1000-MC-BOOT-2.00
                                 SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
                                 IPSec microcode  : CNlite-MC-IPSECm-MAIN-2.06
                                 Number of accelerators: 1

    Could be related to the following bug:
    CSCtq12090: ACL remark line is missing when range object is configured in ACL
    Fixed in 8.4(6), so update to a newer version and observe it again.
    Don't stop after you've improved your network! Improve the world by lending money to the working poor:
    http://www.kiva.org/invitedby/karsteni

  • Show conn in cisco asa

    Hi Team,
    Does the show conn count includes both tcp + udp + embryonic connections.
    Because when i do a calculation in excel from the output of show conn, i got the below output.
    It was extracted from the command "show local-host | include host|count/limit"
    (A):
       Total Sum of TCP embryonic count to host = 331
    (B):
         Total Sum of TCP flow count/limit = 102938
    (C):
         Total Sum of UDP flow count/limit = 3512505
    firewall#show conn count
    1912284 in use, 2000002 most used
    Please let me know how this is caluclated. If show conn count = A+B+C, then i am suspecting that old connection entries are not getting flushed out from the connection table in cisco asa 5580 with version 8.3.2.
    Really im in need of help...

    Hi Kimberly,
    My question was, the count of show conn & show local-host does not match... More over, as the show conn was showing that the max limit of 2 million will be reaching very soon... So, i would like to troubleshoot the output of show local-host | include host|count/limit, where in i could see that one of the webserver has lots of tcp connection (lets say 35000, then the other two servers are consuming udp connections 7lacs,5lacs & 3 lacs, as given below...
    local host: ,
        TCP flow count/limit = 35857/unlimited
        TCP embryonic count to host = 25
        UDP flow count/limit = 0/unlimited
    local host: ,
        TCP flow count/limit = 306/unlimited
        TCP embryonic count to host = 8
        UDP flow count/limit = 736807/unlimited
    local host: ,
        TCP flow count/limit = 246/unlimited
        TCP embryonic count to host = 2
        UDP flow count/limit = 582010/unlimited
    local host: ,
        TCP flow count/limit = 1/unlimited
        TCP embryonic count to host = 0
        UDP flow count/limit = 308412/unlimited
    can you pls let me know any other commands can be executed to know if any huge embryonic/virus attacks/too many broad casts...... Once i clear the local-host, the connections get reduced from a huge value to low value. i reallly do not know if these are geniue traffic or fake ? or do not know if the connection table is not flushing out old entries.. please help

  • Snmp oids for the command "show counters interface intx/y delta"

    Hello,
    I have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..
    Is possible to get these values using SNMP??
    Thank you
    Roman

    Thank you, Dan. These OIDs are for the output from the command "show interface int x/y". But I think, that these OIDs are not for the command "show interface int x/y delta".
    Roman

  • Setting up site to site vpn with cisco asa 5505

    I have a cisco asa 5505 that needs to be set up for site to site vpn to a cisco asa 5500. The 5505 is the remote office and the 5500 is the main office.
    IP of remote office router is 71.37.178.142
    IP of the main office firewall is 209.117.141.82
    Can someone tell me if my config is correct, this is the first time I am setting this up and it can not be tested until I set it up at the remote office. I would rather know its correct before I go.
    ciscoasa# show run
    : Saved
    ASA Version 7.2(4)
    hostname ciscoasa
    domain-name default.domain.invalid
    enable password TMACBloMlcBsq1kp encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.1.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address dhcp setroute
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
    access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 host 209.117.141.82
    access-list inside_nat0_outbound extended permit ip host 71.37.178.142 host 209.117.141.82
    pager lines 24
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-524.bin
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto map outside_map 1 match address outside_1_cryptomap
    crypto map outside_map 1 set pfs group5
    crypto map outside_map 1 set peer 209.117.141.82
    crypto map outside_map 1 set transform-set ESP-AES-256-SHA
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption aes-256
    hash sha
    group 5
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    vpdn username [email protected] password ********* store-local
    dhcpd auto_config outside
    dhcpd address 192.168.1.2-192.168.1.129 inside
    dhcpd enable inside
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:7e338fb2bf32a9ceb89560b314a5ef6c
    : end
    ciscoasa#
    Thanks!

    Hi Mandy,
    By using following access list define Peer IP as source and destination
    access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
    you are not defining the interesting traffic / subnets from both ends.
    Make some number ACL 101 as you do not have to write the extended keyword then if you like as follows, or else NAME aCL will also work:
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    access-list 101 remark CCP_ACL Category=4 access-list 101 remark IPSEC Rule
    !.1..source subnet(called local encryption domain) at your end  192.168.200.0
    !..2.and destination subnet(called remote encryption domain)at other end 192.168.100.0 !.3..I mean you have to define what subnets you need to communicate between which are behind these firewalls
    !..4...Local Subnets behind IP of the main office firewall is 209.117.141.82 say
    !...at your end  192.168.200.0
    !..5.Remote Subnets behind IP of remote office router is 71.37.178.142 say
    !...at other end 192.168.100.0
    Please use Baisc Steps as follows:
    A. Configuration in your MAIN office  having IP = 209.117.141.82  (follow step 1 to 6)
    Step 1.
    Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    Step 2.
    Config ISAKMP Policy with minimum 4 parameters are to be config for
    crypto isakmp policy 10
    authentication pre-share  ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
    encryption aes-256   --->2nd parameter of ISAKMP Policy is OK
    hash sha   --->  3rd parameter of ISAKMP Policy is OK
    group 5  --->  4th parameter of ISAKMP Policy is OK
    lifetime 86400  ------ >  this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
    Step 3.
    Define Preshared key or PKI which you will use with other side Peer address 71.37.178.142, either key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
    Here in your case in step 2 Authentication is using PSK, looks you have not defines Password
    Use following command:
    crypto isakmp key 0 CISCO123 address 71.37.178.142
    or , but not both
    crypto isakmp key 6 CISCO123 address71.37.178.142
    step 4.
    Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
    Here is yours one:
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
    crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
    or
    crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
    Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
    ah-sha-hmac or  ah-md5-hmac
    crypto ipsec transform-set TSET1 ah-sha-hmac
    or
    crypto ipsec transform-set TSET1 ah-md5-hmac
    Step 5.
    Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
    crypto map ipsec-isakmp
    1. Define peer -- called WHO to set tunnel with
    2. Define or call WHICH - Transform Set
    3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
    Like in your case it is but ipsec-isakmp keyword missing in the ;ast
    crypto map outside_map 10 ipsec-isakmp
    1. set peer 209.117.141.82  -----> is correct as this is your other side peer called WHO in my step
    2. set transform-set TSET1  -----> is correct as this is WHICH, and only one transform set can be called
    !..In you case it is correct
    !...set transform-set ESP-AES-256-SHA (also correct)
    3.  match address outside_1_cryptomap  ---->Name of the extended ACL define as WHAT to pass through this tunnel
    4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
    Step 6.
    Now apply this one crypto MAP to your OUTSIDE interface always
    interface outside
    crypto map outside_map
    Configure the same but just change ACL on other end in step one  by reversing source and destination
    and also set the peer IP of this router in other end.
    So other side config should look as follows:
    B.  Configuration in oyur Remote PEER IP having IP = 71.37.178.142 (follow step 7 to 12)
    Step 7.
    Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
    access-list outside_1_cryptomap extended ip 192.168.100.0 0.0.0.255 192.168.200.0 0.0.0.255
    Step 8.
    Config ISAKMP Policy with minimum 4 parameters are to be config for
    crypto isakmp policy 10
    authentication pre-share  ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
    encryption aes-256   --->2nd parameter of ISAKMP Policy is OK
    hash sha   --->  3rd parameter of ISAKMP Policy is OK
    group 5  --->  4th parameter of ISAKMP Policy is OK
    lifetime 86400  ------ >  this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
    Step 9.
    Define Preshared key or PKI which you will use with other side Peer address key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
    Here in your case in step 8 Authentication is using PSK, looks you have not defines Password
    Use following command:
    crypto isakmp key 0 CISCO123 address 209.117.141.82
    or , but not both
    crypto isakmp key 6 CISCO123 address 209.117.141.82
    step 10.
    Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
    Here is yours one:
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
    crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
    or
    crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
    Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
    ah-sha-hmac or  ah-md5-hmac
    crypto ipsec transform-set TSET1 ah-sha-hmac
    or
    crypto ipsec transform-set TSET1 ah-md5-hmac
    Step 11.
    Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
    crypto map    ipsec-isakmp
    1. Define peer -- called WHO to set tunnel with
    2. Define or call WHICH - Transform Set, only one is permissible
    3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
    Like in your case it is but ipsec-isakmp keyword missing in the ;ast
    crypto map outside_map 10 ipsec-isakmp
    1. set peer 209.117.141.82  -----> is correct as this is your other side peer called WHO in my step
    2. set transform-set TSET1  -----> is correct as this is WHICH, and only one transform set can be called
    !..In you case it is correct
    !...set transform-set ESP-AES-256-SHA (also correct)
    3.  match address outside_1_cryptomap  ---->Name of the extended ACL define as WHAT to pass through this tunnel
    4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
    Step 12.
    Now apply this one crypto MAP to your OUTSIDE interface always
    interface outside
    crypto map outside_map
    Now initite a ping
    Here is for your summary:
    IPSec: Site to Site - Routers
    Configuration Steps
    Phase 1
    Step 1: Configure Mirrored ACL/Crypto ACL       for Interesting Traffic
    Step 2: Configure ISAKMP Policy
    Step 3: Configure ISAKMP Key
    Phase 2
    Step 4: Configure Transform Set
    Step 5: Configure Crypto Map
    Step 6: Apply Crypto Map to an Interface
    To debug for Phase 1 and Phase 2. Store it in buffer without displaying logs on terminal.
    Router#debug crpyto isakmp
    Router#debug crpyto ipsec
    Router(config)# logging buffer 7
    Router(config)# logging buffer 99999
    Router(config)# logging console 6
    Router# clear logging
    Configuration
    In R1:
    (config)# access-list 101 permit ipo host 10.1.1.1 host      10.1.2.1
    (config)# crypto isakmp policy 10
    (config-policy)# encryption 3des
    (config-policy)# authentication pre-share
    (config-policy)# group 2
    (config-policy)# hash sha1
    (config)# crypto isakmp key 0 cisco address 2.2.2.1
    (config)# crypto ipsec transform-set TSET esp-3des      sha-aes-hmac
    (config)# crypto map CMAP 10 ipsec-isakmp
    (config-crypto-map)# set peer 2.2.2.1
    (config-crypto-map)# match address 101
    (config-crypto-map)# set transform-set TSET
    (config)# int f0/0
    (config-if)# crypto map CMAP
    Similarly in R2
    Verification Commands
    #show crypto isakmp SA
    #show crypto ipsec SA
    Change to Transport Mode, add the following command in Step 4:
    (config-tranform-set)# mode transport
    Even after  doing this change, the ipsec negotiation will still be done through  tunnel mode if pinged from Loopback to Loopback. To overcome this we  make changes to ACL.
    Change to Aggressive Mode, replace the Step 3 command with these commands in R1:
    (config)# crypto isakmp peer address 2.2.2.1
    (config-peer)# set aggressive-mode password cisco
    (config-peer)# set aggressive-mode clien-endpoint       ipv4-address 2.2.2.1
    Similarly on R2.
    The below process is for the negotiation using RSA-SIG (PKI) as authentication type
    Debug Process:
    After  we debug, we can see the negotiation between the two peers. The first  packet of the interesting traffic triggers the ISAKMP (Phase1)  negotiation. Important messages are marked in BOLD and explanation in  RED
    R2(config)#do ping 10.1.1.1 so lo0 // Interesting Traffic
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
    Packet sent with a source address of 2.2.2.2
    Mar  2 16:18:42.939: ISAKMP:(0): SA request profile is (NULL) //  Router tried to find any IPSec SA matching the outgoing connection but  no valid SA has been found in Security Association Database (SADB)
    Mar  2 16:18:42.939: ISAKMP: Created a peer struct for 20.1.1.10, peer port 500
    Mar  2 16:18:42.939: ISAKMP: New peer created peer = 0x46519678 peer_handle = 0x8000000D
    Mar  2 16:18:42.939: ISAKMP: Locking peer struct 0x46519678, refcount 1 for isakmp_initiator
    Mar  2 16:18:42.939: ISAKMP: local port 500, remote port 500
    Mar  2 16:18:42.939: ISAKMP: set new node 0 to QM_IDLE    
    Mar  2 16:18:42.939: ISAKMP:(0):insert sa successfully sa = 4542B818
    Mar  2 16:18:42.939: ISAKMP:(0):Can not start Aggressive mode, trying Main mode. // Not an error. By default it is configured for Main Mode
    Mar  2 16:18:42.939: ISAKMP:(0):No pre-shared key with 20.1.1.10! // Since we are using RSA Signature, this message. If we use pre-share, this is where it would indicate so!
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-rfc3947 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-07 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-03 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-02 ID
    Mar  2 16:18:42.939: ISAKMP:(0):Input = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
    Mar  2 16:18:42.939: ISAKMP:(0):Old State = IKE_READY  New State = IKE_I_MM1
    Mar  2 16:18:42.943: ISAKMP:(0): beginning Main Mode exchange
    Mar  2 16:18:42.943: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_NO_STATE // Sending ISAKMP Policy to peer
    Mar  2 16:18:42.943: ISAKMP:(0):Sending an IKE IPv4 Packet.
    Mar  2 16:18:42.943: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_NO_STATE // Sending ISAKMP Policy to peer
    Mar  2 16:18:42.947: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:42.947: ISAKMP:(0):Old State = IKE_I_MM1  New State = IKE_I_MM2
    Mar  2 16:18:42.947: ISAKMP:(0): processing SA payload. message ID = 0
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch // Do not worry about this! Not an ERROR!
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
    Mar  2 16:18:42.947:.!!!!
    Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms
    R2(config)# ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): processing IKE frag vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0):Support for IKE Fragmentation not enabled
    Mar  2 16:18:42.947: ISAKMP : Scanning profiles for xauth ...
    Mar  2 16:18:42.947: ISAKMP:(0):Checking ISAKMP transform 1 against priority 10 policy
    Mar  2 16:18:42.947: ISAKMP:      encryption 3DES-CBC
    Mar  2 16:18:42.947: ISAKMP:      hash SHA
    Mar  2 16:18:42.947: ISAKMP:      default group 2
    Mar  2 16:18:42.947: ISAKMP:      auth RSA sig
    Mar  2 16:18:42.947: ISAKMP:      life type in seconds
    Mar  2 16:18:42.947: ISAKMP:      life duration (VPI) of  0x0 0x1 0x51 0x80
    Mar  2 16:18:42.947: ISAKMP:(0):atts are acceptable. Next payload is 0
    Mar  2 16:18:42.947: ISAKMP:(0):Acceptable atts:actual life: 0
    Mar  2 16:18:42.947: ISAKMP:(0):Acceptable atts:life: 0
    Mar  2 16:18:42.947: ISAKMP:(0):Fill atts in sa vpi_length:4
    Mar  2 16:18:42.947: ISAKMP:(0):Fill atts in sa life_in_seconds:86400
    Mar  2 16:18:42.947: ISAKMP:(0):Returning Actual lifetime: 86400
    Mar  2 16:18:42.947: ISAKMP:(0)::Started lifetime timer: 86400.
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.951: ISAKMP:(0): processing IKE frag vendor id payload
    Mar  2 16:18:42.951: ISAKMP:(0):Support for IKE Fragmentation not enabled
    Mar  2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2  New State = IKE_I_MM2
    Mar  2 16:18:42.951: ISAKMP (0): constructing CERT_REQ for issuer cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
    Mar  2 16:18:42.951: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_SA_SETUP // Sending Key Exchange Information to peer
    Mar  2 16:18:42.951: ISAKMP:(0):Sending an IKE IPv4 Packet.
    Mar  2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2  New State = IKE_I_MM3
    Mar  2 16:18:42.955: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_SA_SETUP // Receive key exchange information from peer
    Mar  2 16:18:42.955: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:42.955: ISAKMP:(0):Old State = IKE_I_MM3  New State = IKE_I_MM4
    Mar  2 16:18:42.959: ISAKMP:(0): processing KE payload. message ID = 0
    Mar  2 16:18:43.003: ISAKMP:(0): processing NONCE payload. message ID = 0
    Mar  2 16:18:43.007: ISAKMP:(1008): processing CERT_REQ payload. message ID = 0
    Mar  2 16:18:43.007: ISAKMP:(1008): peer wants a CT_X509_SIGNATURE cert
    Mar  2 16:18:43.007: ISAKMP:(1008): peer wants cert issued by cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
    Mar  2 16:18:43.007:  Choosing trustpoint CA_Server as issuer
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID is Unity
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID seems Unity/DPD but major 180 mismatch
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID is XAUTH
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): speaking to another IOS box!
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008):vendor ID seems Unity/DPD but hash mismatch
    Mar  2 16:18:43.007: ISAKMP:received payload type 20
    Mar  2 16:18:43.007: ISAKMP (1008): His hash no match - this node outside NAT
    Mar  2 16:18:43.007: ISAKMP:received payload type 20
    Mar  2 16:18:43.007: ISAKMP (1008): No NAT Found for self or peer
    Mar  2 16:18:43.007: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:43.007: ISAKMP:(1008):Old State = IKE_I_MM4  New State = IKE_I_MM4
    Mar  2 16:18:43.011: ISAKMP:(1008):Send initial contact
    Mar  2 16:18:43.011: ISAKMP:(1008):My ID configured as IPv4 Addr, but Addr not in Cert!
    Mar  2 16:18:43.011: ISAKMP:(1008):Using FQDN as My ID
    Mar  2 16:18:43.011: ISAKMP:(1008):SA is doing RSA signature authentication using id type ID_FQDN
    Mar  2 16:18:43.011: ISAKMP (1008): ID payload
              next-payload : 6
              type         : 2
              FQDN name    : R2
              protocol     : 17
              port         : 500
              length       : 10
    Mar  2 16:18:43.011: ISAKMP:(1008):Total payload length: 10
    Mar  2 16:18:43.019: ISAKMP (1008): constructing CERT payload for hostname=R2+serialNumber=FHK1502F2H8
    Mar  2 16:18:43.019: ISAKMP:(1008): using the CA_Server trustpoint's keypair to sign
    Mar  2 16:18:43.035: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_KEY_EXCH
    Mar  2 16:18:43.035: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.035: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:43.035: ISAKMP:(1008):Old State = IKE_I_MM4  New State = IKE_I_MM5
    Mar  2 16:18:43.047: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_KEY_EXCH
    // "MM_KEY_EXCH" indicates that the peers have exchanged DH Public keys and generated a shared secret!
    Mar  2 16:18:43.047: ISAKMP:(1008): processing ID payload. message ID = 0
    Mar  2 16:18:43.047: ISAKMP (1008): ID payload
              next-payload : 6
              type         : 2
              FQDN name    : ASA1
              protocol     : 0
              port         : 0
              length       : 12
    Mar  2 16:18:43.047: ISAKMP:(0):: peer matches *none* of the profiles // Normal Message! Not an error!
    Mar  2 16:18:43.047: ISAKMP:(1008): processing CERT payload. message ID = 0
    Mar  2 16:18:43.047: ISAKMP:(1008): processing a CT_X509_SIGNATURE cert
    Mar  2 16:18:43.051: ISAKMP:(1008): peer's pubkey isn't cached
    Mar  2 16:18:43.059: ISAKMP:(1008): Unable to get DN from certificate!
    Mar  2 16:18:43.059: ISAKMP:(1008): Cert presented by peer contains no OU field.
    Mar  2 16:18:43.059: ISAKMP:(0):: peer matches *none* of the profiles
    Mar  2 16:18:43.063: ISAKMP:(1008): processing SIG payload. message ID = 0
    Mar  2 16:18:43.067: ISAKMP:received payload type 17
    Mar  2 16:18:43.067: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.067: ISAKMP:(1008): vendor ID is DPD
    Mar  2 16:18:43.067: ISAKMP:(1008):SA authentication status:
              authenticated
    Mar  2 16:18:43.067: ISAKMP:(1008):SA has been authenticated with 20.1.1.10
    Mar  2 16:18:43.067: ISAKMP: Trying to insert a peer 40.1.1.1/20.1.1.10/500/,  and inserted successfully 46519678. // SA inserted into SADB
    Mar  2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM5  New State = IKE_I_MM6
    Mar  2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM6  New State = IKE_I_MM6
    Mar  2 16:18:43.071: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:43.071: ISAKMP:(1008):Old State = IKE_I_MM6  New State = IKE_P1_COMPLETE
    Mar  2 16:18:43.071: ISAKMP:(1008):beginning Quick Mode exchange, M-ID of -1523793378
    Mar  2 16:18:43.071: ISAKMP:(1008):QM Initiator gets spi
    Mar  2 16:18:43.075: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE    
    Mar  2 16:18:43.075: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.075: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_INTERNAL, IKE_INIT_QM
    Mar  2 16:18:43.075: ISAKMP:(1008):Old State = IKE_QM_READY  New State = IKE_QM_I_QM1
    Mar  2 16:18:43.075: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
    Mar  2 16:18:43.075: ISAKMP:(1008):Old State = IKE_P1_COMPLETE  New State = IKE_P1_COMPLETE
    Mar  2 16:18:43.079: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) QM_IDLE // IPSec Policies
    Mar  2 16:18:43.079: ISAKMP:(1008): processing HASH payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing SA payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008):Checking IPSec proposal 1
    Mar  2 16:18:43.079: ISAKMP: transform 1, ESP_3DES
    Mar  2 16:18:43.079: ISAKMP:   attributes in transform:
    Mar  2 16:18:43.079: ISAKMP:      SA life type in seconds
    Mar  2 16:18:43.079: ISAKMP:      SA life duration (basic) of 3600
    Mar  2 16:18:43.079: ISAKMP:      SA life type in kilobytes
    Mar  2 16:18:43.079: ISAKMP:      SA life duration (VPI) of  0x0 0x46 0x50 0x0
    Mar  2 16:18:43.079: ISAKMP:      encaps is 1 (Tunnel)
    Mar  2 16:18:43.079: ISAKMP:      authenticator is HMAC-SHA
    Mar  2 16:18:43.079: ISAKMP:(1008):atts are acceptable. // IPSec attributes are acceptable!
    Mar  2 16:18:43.079: ISAKMP:(1008): processing NONCE payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
    Mar  2 16:18:43.083: ISAKMP:(1008): Creating IPSec SAs
    Mar  2 16:18:43.083:         inbound SA from 20.1.1.10 to 40.1.1.1 (f/i)  0/ 0
              (proxy 1.1.1.1 to 2.2.2.2)
    Mar  2 16:18:43.083:         has spi 0xA9A66D46 and conn_id 0
    Mar  2 16:18:43.083:         lifetime of 3600 seconds
    Mar  2 16:18:43.083:         lifetime of 4608000 kilobytes
    Mar  2 16:18:43.083:         outbound SA from 40.1.1.1 to 20.1.1.10 (f/i) 0/0
              (proxy 2.2.2.2 to 1.1.1.1)
    Mar  2 16:18:43.083:         has spi  0x2B367FB4 and conn_id 0
    Mar  2 16:18:43.083:         lifetime of 3600 seconds
    Mar  2 16:18:43.083:         lifetime of 4608000 kilobytes
    Mar  2 16:18:43.083: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE    
    Mar  2 16:18:43.083: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.083: ISAKMP:(1008):deleting node -1523793378 error FALSE reason "No Error"
    Mar  2 16:18:43.083: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
    Mar  2 16:18:43.083: ISAKMP:(1008):Old State = IKE_QM_I_QM1  New State = IKE_QM_PHASE2_COMPLETE // At this point tunnels are up and ready to pass traffic!
    Verification Commands
    #show crypto isakmp SA
    #show crypto ipsec SA
    Kindly rate if you find the explanation useful !!
    Best Regards
    Sachin Garg

  • Cisco ASA 5505 VPN connection issue ("Unable to add route")

    I'm trying to get IPSec VPN working onto a new Cisco ASA5505. Pretty standard configuration.
    Setup:
    * Cisco VPN client on Windows 7 (v5.0.07.0290 x64 on Laptop1 and v5.0.07.0440 x64 on Laptop2)
    * PPPoE/NAT and internal DHCP on the ASA were configured with the Startup Wizard in ASDM
    NATting is working fine - internal PCs get an IP address in the 192.168.2.0/24 range and can all access the Internet.
    I wanted to be able to connect from anywhere to the ASA in order to reach one of the internal servers. Should be pretty basic.
    First I tried with the built-in ASDM IPSec Wizard, instructions found here.
    VPN clients can connect to the ASA, are connected (until they're manually disconnected), but cannot reach the internal network nor the Internet. Note VPN client can connect fine to a different VPN site (not administered by myself).
    Client logs show following error messages:
    1 15:53:09.363 02/11/12 Sev=Warning/3     IKE/0xA300005F
    Firewall, Cisco Intrusion Prevention Security Agent, is not running, the client will not send firewall information to concentrator.
    2 15:53:13.593 02/11/12 Sev=Warning/2     CVPND/0xE3400013
    AddRoute failed to add a route with metric of 0: code 160
    Destination     192.168.1.255
    Netmask     255.255.255.255
    Gateway     172.16.1.1
    Interface     172.16.1.101
    3 15:53:13.593 02/11/12 Sev=Warning/2     CM/0xA3100024
    Unable to add route. Network: c0a801ff, Netmask: ffffffff, Interface: ac100165, Gateway: ac100101.
    4 15:54:30.425 02/11/12 Sev=Warning/2     CVPND/0xA3400015
    Error with call to IpHlpApi.DLL: CheckUpVASettings: Found IPADDR entry addr=172.16.1.101, error 0
    5 15:54:31.433 02/11/12 Sev=Warning/2     CVPND/0xA3400015
    Error with call to IpHlpApi.DLL: CheckUpVASettings: Found IPADDR entry addr=172.16.1.101, error 0
    6 15:54:32.445 02/11/12 Sev=Warning/2     CVPND/0xA3400015
    Error with call to IpHlpApi.DLL: CleanUpVASettings: Was able to delete all VA settings after all, error 0
    7 20:50:45.355 02/11/12 Sev=Warning/3     IKE/0xA300005F
    Firewall, Cisco Intrusion Prevention Security Agent, is not running, the client will not send firewall information to concentrator.
    8 20:50:50.262 02/11/12 Sev=Warning/2     CVPND/0xE3400013
    AddRoute failed to add a route with metric of 0: code 160
    Destination     192.168.1.255
    Netmask     255.255.255.255
    Gateway     172.16.1.1
    Interface     172.16.1.100
    9 20:50:50.262 02/11/12 Sev=Warning/2     CM/0xA3100024
    Unable to add route. Network: c0a801ff, Netmask: ffffffff, Interface: ac100164, Gateway: ac100101.
    I've already tried the suggestions from this link, although the problem is different there (as the user can still access the internet, even without split tunneling, which I cannot).
    A show run shows the following output (note in the below I have tried a different VPN network: 192.168.3.0/24 instead of 172.16.1.0/24 seen in the Client log)
    Result of the command: "sh run"
    : Saved
    ASA Version 8.2(5)
    hostname AsaDWD
    enable password kLu0SYBETXUJHVHX encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.2.254 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    pppoe client vpdn group DW-VPDN
    ip address pppoe setroute
    ftp mode passive
    access-list inside_nat0_outbound extended permit ip any 192.168.3.0 255.255.255.240
    pager lines 24
    logging enable
    logging asdm informational
    mtu outside 1500
    mtu inside 1500
    ip local pool DWD-VPN-Pool 192.168.3.5-192.168.3.15 mask 255.255.255.0
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    http server enable
    http 192.168.2.0 255.255.255.0 inside
    http 0.0.0.0 0.0.0.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    vpdn group DW-VPDN request dialout pppoe
    vpdn group DW-VPDN localname fa******@SKYNET
    vpdn group DW-VPDN ppp authentication pap
    vpdn username fa******@SKYNET password *****
    dhcpd auto_config outside
    dhcpd address 192.168.2.5-192.168.2.36 inside
    dhcpd domain DOMAIN interface inside
    dhcpd enable inside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    group-policy DWD internal
    group-policy DWD attributes
    vpn-tunnel-protocol IPSec
    username test password ******* encrypted privilege 0
    username test attributes
    vpn-group-policy DWD
    tunnel-group DWD type remote-access
    tunnel-group DWD general-attributes
    address-pool DWD-VPN-Pool
    default-group-policy DWD
    tunnel-group DWD ipsec-attributes
    pre-shared-key *****
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
    message-length maximum client auto
    message-length maximum 512
    policy-map global_policy
    class inspection_default
    inspect dns preset_dns_map
    inspect ftp
    inspect h323 h225
    inspect h323 ras
    inspect rsh
    inspect rtsp
    inspect esmtp
    inspect sqlnet
    inspect skinny
    inspect sunrpc
    inspect xdmcp
    inspect sip
    inspect netbios
    inspect tftp
    inspect ip-options
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    Cryptochecksum:3e6c9478a1ee04ab2e1e1cabbeddc7f4
    : end
    I've installed everything using the CLI as well (after a factory reset). This however yielded exactl the same issue.
    Following commands have been entered:
    ip local pool vpnpool 172.16.1.100-172.16.1.199 mask 255.255.255.0
    username *** password ****
    isakmp policy 1 authentication pre-share
    isakmp policy 1 encryption 3des
    isakmp policy 1 hash sha
    isakmp policy 1 group 2
    isakmp policy 1 lifetime 43200
    isakmp enable outside
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto dynamic-map outside_dyn_map 10 set transform-set ESP-3DES-SHA
    crypto dynamic-map outside_dyn_map 10 set reverse-route
    crypto dynamic-map outside_dyn_map 10 set security-association lifetime seconds 288000
    crypto map outside_map 10 ipsec-isakmp dynamic outside_dyn_map
    crypto map outside_map interface outside
    crypto isakmp nat-traversal
    sysopt connection permit-ipsec
    sysopt connection permit-vpn
    group-policy dwdvpn internal
    group-policy dwdvpn attributes
    vpn-tunnel-protocol IPSec
    default-domain value DWD
    tunnel-group dwdvpn type ipsec-ra
    tunnel-group dwdvpn ipsec-attributes
    pre-shared-key ****
    tunnel-group dwdvpn general-attributes
    authentication-server-group LOCAL
    default-group-policy dwdvpn
    Unfortunately I'm getting the same "AddRoute failed to add a route with metric of 0: code 160" error message.
    I'm very confused as this should be a pretty standard setup. I tried to follow the instructions on the Cisco site to the letter...
    The only "differences" in my setup are an internal network of 192.168.2.0 (with ASA IP address 192.168.2.254) and PPPoE with DHCP instead of no PPPoE at all.
    Does anyone know what's going on?

    Yes, I have tried from a different laptop - same results. Using that laptop I can connect to a different IPSec site without issues.
    Please find my renewed config below:
    DWD-ASA(config)# sh run: Saved:ASA Version 8.2(5) !hostname DWD-ASAenable password ******* encryptedpasswd ****** encryptednames!interface Ethernet0/0 switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1 nameif inside security-level 100 ip address 192.168.2.254 255.255.255.0 !interface Vlan2 nameif outside security-level 0 pppoe client vpdn group DWD ip address pppoe setroute !ftp mode passiveaccess-list inside_nat0_outbound extended permit ip any 192.168.50.0 255.255.255.224 pager lines 24logging asdm informationalmtu inside 1500mtu outside 1500ip local pool vpnpool 192.168.50.10-192.168.50.20 mask 255.255.255.0icmp unreachable rate-limit 1 burst-size 1no asdm history enablearp timeout 14400global (outside) 1 interfacenat (inside) 0 access-list inside_nat0_outboundnat (inside) 1 0.0.0.0 0.0.0.0timeout xlate 3:00:00timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolutetimeout tcp-proxy-reassembly 0:01:00timeout floating-conn 0:00:00dynamic-access-policy-record DfltAccessPolicyhttp server enablehttp 192.168.2.0 255.255.255.0 insidehttp 0.0.0.0 0.0.0.0 outsideno snmp-server locationno snmp-server contactsnmp-server enable traps snmp authentication linkup linkdown coldstartcrypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec security-association lifetime seconds 28800crypto ipsec security-association lifetime kilobytes 4608000crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAPcrypto map outside_map interface outsidecrypto isakmp enable outsidecrypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400telnet timeout 5ssh 0.0.0.0 0.0.0.0 outsidessh timeout 5console timeout 0vpdn group DWD request dialout pppoevpdn group DWD localname *****@SKYNETvpdn group DWD ppp authentication papvpdn username *****@SKYNET password ***** dhcpd auto_config outside!dhcpd address 192.168.2.10-192.168.2.40 insidedhcpd enable inside!threat-detection basic-threatthreat-detection statistics access-listno threat-detection statistics tcp-interceptwebvpn enable outside svc enablegroup-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpngroup-policy dwdipsec internalgroup-policy dwdipsec attributes vpn-tunnel-protocol IPSec default-domain value DWDDOMusername user1 password ***** encrypted privilege 0username user1 attributes vpn-group-policy dwdipsectunnel-group dwdipsec type remote-accesstunnel-group dwdipsec general-attributes address-pool vpnpool default-group-policy dwdipsectunnel-group dwdipsec ipsec-attributes pre-shared-key *****tunnel-group dwdssl type remote-accesstunnel-group dwdssl general-attributes address-pool vpnpool!class-map inspection_default match default-inspection-traffic!!policy-map type inspect dns preset_dns_map parameters  message-length maximum client auto  message-length maximum 512policy-map global_policy class inspection_default  inspect dns preset_dns_map   inspect ftp   inspect h323 h225   inspect h323 ras   inspect rsh   inspect rtsp   inspect esmtp   inspect sqlnet   inspect skinny    inspect sunrpc   inspect xdmcp   inspect sip    inspect netbios   inspect tftp   inspect ip-options !service-policy global_policy globalprompt hostname context no call-home reporting anonymousCryptochecksum:f5c8dd644aa2a27374a923671da1c834: endDWD-ASA(config)#

  • VPN PROBLEM CISCO ASA 5505

        Hello,  I have been trying to configure a VPN with Cisco Asa 5505 and Cisco VPN client 5.X for 3 weeks and I am not being able to accomplish it, so I decided to reset to factory defaults and start over again.
         I used ASDM 6.4 VPN wizard to configure it (I selected exempt local network from NAT and enabled split tunneling, but I have tried other combinations as well).
         Tunnel seems to be established properly since I do see an endpoint while using 'sh crypto isakmp sa' but 'sh crypto ipsec sa' shows no packets encrypted or decrypted, so VPN is not working as expected. I can't ping or rdp to internal LAN:
         #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
          #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
         The running-config it created is:
    ciscoasa# sh run
    : Saved
    ASA Version 8.4(2)
    hostname ciscoasa
    enable password XXXX encrypted
    passwd XXXX encrypted
    names
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    nameif inside
    security-level 100
    ip address 172.16.1.254 255.255.0.0
    interface Vlan2
    nameif outside
    security-level 0
    pppoe client vpdn group ADSL_Telefonica
    ip address pppoe setroute
    ftp mode passive
    object network obj_any
    subnet 0.0.0.0 0.0.0.0
    object network NETWORK_OBJ_10.0.0.0_24
    subnet 10.0.0.0 255.255.255.0
    object network NETWORK_OBJ_172.16.0.0_16
    subnet 172.16.0.0 255.255.0.0
    access-list test_splitTunnelAcl standard permit 172.16.0.0 255.255.0.0
    pager lines 24
    logging asdm informational
    mtu outside 1500
    mtu inside 1500
    ip local pool test 10.0.0.1-10.0.0.254 mask 255.255.255.0
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    nat (inside,outside) source static NETWORK_OBJ_172.16.0.0_16 NETWORK_OBJ_172.16.0.0_16 destination static NETWORK_OBJ_10.0.0.0_24 NETWORK_OBJ_10.0.0.0_24 no-proxy-arp route-lookup
    object network obj_any
    nat (inside,outside) dynamic interface
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    aaa authentication ssh console LOCAL
    http server enable
    http 172.16.0.0 255.255.0.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map outside_map interface outside
    crypto ikev1 enable outside
    crypto ikev1 policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet 172.16.0.0 255.255.0.0 inside
    telnet timeout 55
    ssh 172.16.0.0 255.255.0.0 inside
    ssh timeout 55
    console timeout 0
    vpdn group ADSL_Telefonica request dialout pppoe
    vpdn group ADSL_Telefonica localname adslppp@telefonicanetpa
    vpdn group ADSL_Telefonica ppp authentication pap
    vpdn username adslppp@telefonicanetpa password *****
    dhcpd auto_config outside
    dhcpd address 172.16.2.2-172.16.2.129 inside
    dhcpd enable inside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    group-policy test internal
    group-policy test attributes
    dns-server value 172.16.1.1
    vpn-tunnel-protocol ikev1
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value test_splitTunnelAcl
    username test password XXXXXX encrypted privilege 0
    username test attributes
    vpn-group-policy test
    username ignacio password XXXXXXX encrypted
    tunnel-group test type remote-access
    tunnel-group test general-attributes
    address-pool test
    default-group-policy test
    tunnel-group test ipsec-attributes
    ikev1 pre-shared-key *****
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    Cryptochecksum:c8935bd572dfd37e81c6aa9f9dc8207c
    : end
    Thank you very much for your help

    Yes, it was a VPN client problem. I was doing test with a WWAN card and it seems it is not compatible with windows 7.
    • The VPN Client on Windows 7 does not support WWAN devices (also called wireless data cards).
    I should have read Release Notes before. Thank you very much for your help and effort.

  • Unable to access/lan2lan ping from VPN Fortigate to Cisco ASA 5505

    Problem : Unable to access user A to user B
    User A --- router A (122, fortigate 80c) --- (Site to Site VPN between fortigate & cisco asa) --- router B (93, cisco Asa 5505{in front asa got cisco800[81] before to internet} )  --- User B
    After using wizard to configure the cisco ASA site to site VPN, the site-to-site tunnel is up.
    Ping is unsuccessful from user A to user B
    Ping is successful from user B to user A, data is accessable
    After done the packet tracer from user A to user B,
    Result :
    Flow-lookup
    Action : allow
    Info: Found no matching flow, creating a new flow
    Route-lookup
    Action : allow
    Info : 192.168.5.203 255.255.255.255 identity
    Access-list
    Action : drop
    Config Implicit Rule
    Result - The packet is dropped
    Input Interface : inside
    Output Interface : NP Identify Ifc
    Info: (acl-drop)flow is denied by configured rule
    Below is Cisco ASA 5505's show running-config
    ASA Version 8.2(1)
    hostname Asite
    domain-name ssms1.com
    enable password ZZZZ encrypted
    passwd WWWW encrypted
    names
    name 82 B-firewall description Singapore office firewall
    name 192.168.1.0 B-inside-subnet description Singapore office internal LAN IP
    name 192.168.200.0 A-inside-VLAN12 description A-inside-VLAN12 (fortinet)
    name 192.168.2.0 fw-inside-subnet description A office internal LAN IP
    name 122 A-forti
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.5.203 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address 93 255.255.255.240
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/7
    ftp mode passive
    dns server-group DefaultDNS
    domain-name ssms1.com
    object-group network obj_any
    network-object 0.0.0.0 0.0.0.0
    access-list inside_nat0_outbound extended permit ip any 80 255.255.255.240
    access-list inside_nat0_outbound extended permit ip fw-inside-subnet 255.255.255.0 B-inside-subnet 255.255.255.0
    access-list inside_nat0_outbound extended permit ip 192.168.5.0 255.255.255.0 A-inside-VLAN12 255.255.255.0
    access-list outside_cryptomap extended permit ip fw-inside-subnet 255.255.255.0 B-inside-subnet 255.255.255.0
    access-list Outside_nat-inbound extended permit ip A-inside-VLAN12 255.255.255.0 192.168.5.0 255.255.255.0
    access-list Outside_nat-inbound extended permit ip host A-forti 192.168.5.0 255.255.255.0
    access-list outside_1_cryptomap extended permit ip 192.168.5.0 255.255.255.0 A-inside-VLAN12 255.255.255.0
    pager lines 24
    logging enable
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-631.bin
    no asdm history enable
    arp timeout 14400
    global (outside) 101 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 101 0.0.0.0 0.0.0.0
    route outside 0.0.0.0 0.0.0.0 81 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-record DfltAccessPolicy
    http server enable
    http B-inside-subnet 255.255.255.0 inside
    http fw-inside-subnet 255.255.255.0 inside
    http 0.0.0.0 255.255.255.255 outside
    http 0.0.0.0 0.0.0.0 outside
    http 192.168.5.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto map outside_map 1 match address outside_1_cryptomap
    crypto map outside_map 1 set pfs
    crypto map outside_map 1 set peer A-forti
    crypto map outside_map 1 set transform-set ESP-3DES-SHA
    crypto map outside_map 2 match address outside_cryptomap
    crypto map outside_map 2 set peer B-firewall
    crypto map outside_map 2 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto isakmp policy 20
    authentication pre-share
    encryption aes-192
    hash md5
    group 2
    lifetime 86400
    crypto isakmp policy 30
    authentication pre-share
    encryption aes-256
    hash md5
    group 2
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    dhcpd auto_config outside
    dhcpd address 192.168.5.10-192.168.5.20 inside
    dhcpd dns 165 165 interface inside
    dhcpd enable inside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    group-policy DfltGrpPolicy attributes
    vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
    username admin password XXX encrypted privilege 15
    tunnel-group 122 type ipsec-l2l
    tunnel-group 122 ipsec-attributes
    pre-shared-key *
    class-map inspection_default
    match default-inspection-traffic
    class-map outside-class
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
      message-length maximum client auto
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect icmp
    policy-map outside-policy
    description ok
    class outside-class
      inspect dns
      inspect esmtp
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect icmp
      inspect icmp error
      inspect netbios
      inspect rsh
      inspect rtsp
      inspect sip
      inspect skinny
      inspect sqlnet
      inspect sunrpc
      inspect tftp
      inspect xdmcp
    service-policy global_policy global
    service-policy outside-policy interface outside
    prompt hostname context
    Cryptochecksum: XXX
    : end
    Kindly need your expertise&help to solve the problem

    any1 can help me ?

  • %ASA-7-710005: TCP request discarded error in Client to Site VPN in CISCO ASA 5510

    Hi Friends,
    I'm trying to built client to site VPN in CISCO ASA 5510 8.4(4) and getting below error while connecting cisco VPN client software. Also, I'm getting below log in ASA. Please help me to reslove.
    Error in CISCO VPN Client Software:
    Secure VPN Connection Terminated locally by the client.
    Reason : 414 : Failed to establish a TCP connection.
    Error in CISCO ASA 5510
    %ASA-7-710005: TCP request discarded from <Public IP> /49276 to outside:<Outside Interface IP of my ASA> /10000
    ASA Configuration:
    XYZ# sh run
    : Saved
    ASA Version 8.4(4)
    hostname XYZ
    domain-name XYZ
    enable password 3uLkVc9JwRA1/OXb level 3 encrypted
    enable password R/x90UjisGVJVlh2 encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Ethernet0/0
    nameif outside_rim
    security-level 0
    ip address 1.1.1.1 255.255.255.252
    interface Ethernet0/1
    duplex full
    nameif XYZ_DMZ
    security-level 50
    ip address 172.1.1.1 255.255.255.248
    interface Ethernet0/2
    speed 100
    duplex full
    nameif outside
    security-level 0
    ip address 2.2.2.2 255.255.255.252
    interface Ethernet0/3
    speed 100
    duplex full
    nameif inside
    security-level 100
    ip address 3.3.3.3 255.255.255.224
    interface Management0/0
    shutdown
    no nameif
    no security-level
    no ip address
    boot system disk0:/asa844-k8.bin
    ftp mode passive
    dns domain-lookup outside
    dns server-group DefaultDNS
    name-server xx.xx.xx.xx
    name-server xx.xx.xx.xx
    name-server xx.xx.xx.xx
    name-server xx.xx.xx.xx
    domain-name XYZ
    object network obj-172.17.10.3
    host 172.17.10.3
    object network obj-10.1.134.0
    subnet 10.1.134.0 255.255.255.0
    object network obj-208.75.237.0
    subnet 208.75.237.0 255.255.255.0
    object network obj-10.7.0.0
    subnet 10.7.0.0 255.255.0.0
    object network obj-172.17.2.0
    subnet 172.17.2.0 255.255.255.0
    object network obj-172.17.3.0
    subnet 172.17.3.0 255.255.255.0
    object network obj-172.19.2.0
    subnet 172.19.2.0 255.255.255.0
    object network obj-172.19.3.0
    subnet 172.19.3.0 255.255.255.0
    object network obj-172.19.7.0
    subnet 172.19.7.0 255.255.255.0
    object network obj-10.1.0.0
    subnet 10.1.0.0 255.255.0.0
    object network obj-10.2.0.0
    subnet 10.2.0.0 255.255.0.0
    object network obj-10.3.0.0
    subnet 10.3.0.0 255.255.0.0
    object network obj-10.4.0.0
    subnet 10.4.0.0 255.255.0.0
    object network obj-10.6.0.0
    subnet 10.6.0.0 255.255.0.0
    object network obj-10.9.0.0
    subnet 10.9.0.0 255.255.0.0
    object network obj-10.11.0.0
    subnet 10.11.0.0 255.255.0.0
    object network obj-10.12.0.0
    subnet 10.12.0.0 255.255.0.0
    object network obj-172.19.1.0
    subnet 172.19.1.0 255.255.255.0
    object network obj-172.21.2.0
    subnet 172.21.2.0 255.255.255.0
    object network obj-172.16.2.0
    subnet 172.16.2.0 255.255.255.0
    object network obj-10.19.130.201
    host 10.19.130.201
    object network obj-172.30.2.0
    subnet 172.30.2.0 255.255.255.0
    object network obj-172.30.3.0
    subnet 172.30.3.0 255.255.255.0
    object network obj-172.30.7.0
    subnet 172.30.7.0 255.255.255.0
    object network obj-10.10.1.0
    subnet 10.10.1.0 255.255.255.0
    object network obj-10.19.130.0
    subnet 10.19.130.0 255.255.255.0
    object network obj-XXXXXXXX
    host XXXXXXXX
    object network obj-145.248.194.0
    subnet 145.248.194.0 255.255.255.0
    object network obj-10.1.134.100
    host 10.1.134.100
    object network obj-10.9.124.100
    host 10.9.124.100
    object network obj-10.1.134.101
    host 10.1.134.101
    object network obj-10.9.124.101
    host 10.9.124.101
    object network obj-10.1.134.102
    host 10.1.134.102
    object network obj-10.9.124.102
    host 10.9.124.102
    object network obj-115.111.99.133
    host 115.111.99.133
    object network obj-10.8.108.0
    subnet 10.8.108.0 255.255.255.0
    object network obj-115.111.99.129
    host 115.111.99.129
    object network obj-195.254.159.133
    host 195.254.159.133
    object network obj-195.254.158.136
    host 195.254.158.136
    object network obj-209.164.192.0
    subnet 209.164.192.0 255.255.224.0
    object network obj-209.164.208.19
    host 209.164.208.19
    object network obj-209.164.192.126
    host 209.164.192.126
    object network obj-10.8.100.128
    subnet 10.8.100.128 255.255.255.128
    object network obj-115.111.99.130
    host 115.111.99.130
    object network obj-10.10.0.0
    subnet 10.10.0.0 255.255.0.0
    object network obj-115.111.99.132
    host 115.111.99.132
    object network obj-10.10.1.45
    host 10.10.1.45
    object network obj-10.99.132.0
    subnet 10.99.132.0 255.255.255.0
    object-group network Serversubnet
    network-object 10.10.1.0 255.255.255.0
    network-object 10.10.5.0 255.255.255.192
    object-group network XYZ_destinations
    network-object 10.1.0.0 255.255.0.0
    network-object 10.2.0.0 255.255.0.0
    network-object 10.3.0.0 255.255.0.0
    network-object 10.4.0.0 255.255.0.0
    network-object 10.6.0.0 255.255.0.0
    network-object 10.7.0.0 255.255.0.0
    network-object 10.11.0.0 255.255.0.0
    network-object 10.12.0.0 255.255.0.0
    network-object 172.19.1.0 255.255.255.0
    network-object 172.19.2.0 255.255.255.0
    network-object 172.19.3.0 255.255.255.0
    network-object 172.19.7.0 255.255.255.0
    network-object 172.17.2.0 255.255.255.0
    network-object 172.17.3.0 255.255.255.0
    network-object 172.16.2.0 255.255.255.0
    network-object 172.16.3.0 255.255.255.0
    network-object host 10.50.2.206
    object-group network XYZ_us_admin
    network-object 10.3.1.245 255.255.255.255
    network-object 10.5.33.7 255.255.255.255
    network-object 10.211.5.7 255.255.255.255
    network-object 10.3.33.7 255.255.255.255
    network-object 10.211.3.7 255.255.255.255
    object-group network XYZ_blr_networkdevices
    network-object 10.200.10.0 255.255.255.0
    access-list XYZ extended permit ip 10.19.130.0 255.255.255.0 145.248.194.0 255.255.255.0
    access-list XYZ extended permit ip 10.19.130.0 255.255.255.0 host 172.16.2.21
    access-list XYZ extended permit ip 10.19.130.0 255.255.255.0 host 172.16.2.22
    access-list XYZ extended permit ip 10.19.130.0 255.255.255.0 host XXXXXXXX
    access-list XYZ_PAT extended permit ip 10.19.130.0 255.255.255.0 any
    access-list XYZ_PAT extended permit ip 10.1.134.0 255.255.255.0 host 195.254.159.133
    access-list XYZ_PAT extended permit ip 10.1.134.0 255.255.255.0 host 195.254.158.136
    access-list XYZ_PAT extended permit ip 10.1.134.0 255.255.255.0 any
    access-list XYZ_PAT extended permit ip 10.1.134.0 255.255.255.0 209.164.192.0 255.255.224.0
    access-list XYZ_PAT extended permit ip 10.1.134.0 255.255.255.0 host 209.164.208.19
    access-list XYZ_PAT extended permit ip 10.1.134.0 255.255.255.0 host 209.164.192.126
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 208.75.237.0 255.255.255.0
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.7.0.0 255.255.0.0
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 172.17.2.0 255.255.255.0
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 172.17.3.0 255.255.255.0
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 172.19.2.0 255.255.255.0
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 172.19.3.0 255.255.255.0
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 172.19.7.0 255.255.255.0
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.1.0.0 255.255.0.0
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.2.0.0 255.255.0.0
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.3.0.0 255.255.0.0
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.4.0.0 255.255.0.0
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.6.0.0 255.255.0.0
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.9.0.0 255.255.0.0
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.11.0.0 255.255.0.0
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 10.12.0.0 255.255.0.0
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 172.19.1.0 255.255.255.0
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 172.21.2.0 255.255.255.0
    access-list nonat extended permit ip 10.1.134.0 255.255.255.0 172.16.2.0 255.255.255.0
    access-list nonat extended permit ip host 10.19.130.201 172.30.2.0 255.255.255.0
    access-list nonat extended permit ip host 10.19.130.201 172.30.3.0 255.255.255.0
    access-list nonat extended permit ip host 10.19.130.201 172.30.7.0 255.255.255.0
    access-list nonat extended permit ip object-group Serversubnet object-group XYZ_destinations
    access-list nonat extended permit ip 10.10.1.0 255.255.255.0 10.2.0.0 255.255.0.0
    access-list nonat extended permit ip 10.19.130.0 255.255.255.0 host XXXXXXXX
    access-list nonat extended permit ip 10.19.130.0 255.255.255.0 145.248.194.0 255.255.255.0
    access-list Guest_PAT extended permit ip 10.8.108.0 255.255.255.0 any
    access-list Cacib extended permit ip 10.8.100.128 255.255.255.128 145.248.194.0 255.255.255.0
    access-list Cacib_PAT extended permit ip 10.8.100.128 255.255.255.128 any
    access-list New_Edge extended permit ip 10.1.134.0 255.255.255.0 208.75.237.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.7.0.0 255.255.0.0 10.1.134.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.7.0.0 255.255.0.0
    access-list XYZ_global extended permit ip 172.17.2.0 255.255.255.0 10.1.134.0 255.255.255.0
    access-list XYZ_global extended permit ip 172.17.3.0 255.255.255.0 10.1.134.0 255.255.255.0
    access-list XYZ_global extended permit ip 172.19.2.0 255.255.255.0 10.1.134.0 255.255.255.0
    access-list XYZ_global extended permit ip 172.19.3.0 255.255.255.0 10.1.134.0 255.255.255.0
    access-list XYZ_global extended permit ip 172.19.7.0 255.255.255.0 10.1.134.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.1.0.0 255.255.0.0 10.1.134.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.2.0.0 255.255.0.0 10.1.134.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.3.0.0 255.255.0.0 10.1.134.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.4.0.0 255.255.0.0 10.1.134.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.6.0.0 255.255.0.0 10.1.134.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.9.0.0 255.255.0.0 10.1.134.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.11.0.0 255.255.0.0 10.1.134.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.12.0.0 255.255.0.0 10.1.134.0 255.255.255.0
    access-list XYZ_global extended permit ip 172.19.1.0 255.255.255.0 10.1.134.0 255.255.255.0
    access-list XYZ_global extended permit ip 172.21.2.0 255.255.255.0 10.1.134.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 172.17.2.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 172.17.3.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 172.19.2.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 172.19.3.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 172.19.7.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.1.0.0 255.255.0.0
    access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.2.0.0 255.255.0.0
    access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.3.0.0 255.255.0.0
    access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.4.0.0 255.255.0.0
    access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.6.0.0 255.255.0.0
    access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.9.0.0 255.255.0.0
    access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.11.0.0 255.255.0.0
    access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 10.12.0.0 255.255.0.0
    access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 172.19.1.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 172.21.2.0 255.255.255.0
    access-list XYZ_global extended permit ip 172.16.2.0 255.255.255.0 10.1.134.0 255.255.255.0
    access-list XYZ_global extended permit ip 10.1.134.0 255.255.255.0 172.16.2.0 255.255.255.0
    access-list XYZ_global extended permit ip 172.30.2.0 255.255.255.0 host 10.19.130.201
    access-list XYZ_global extended permit ip host 10.19.130.201 172.30.2.0 255.255.255.0
    access-list XYZ_global extended permit ip 172.30.3.0 255.255.255.0 host 10.19.130.201
    access-list XYZ_global extended permit ip host 10.19.130.201 172.30.3.0 255.255.255.0
    access-list XYZ_global extended permit ip 172.30.7.0 255.255.255.0 host 10.19.130.201
    access-list XYZ_global extended permit ip host 10.19.130.201 172.30.7.0 255.255.255.0
    access-list XYZ_global extended permit ip object-group Serversubnet object-group XYZ_destinations
    access-list XYZ_global extended permit ip object-group XYZ_destinations object-group Serversubnet
    access-list ML_VPN extended permit ip host 115.111.99.129 209.164.192.0 255.255.224.0
    access-list ML_VPN extended permit ip host 115.111.99.129 host 209.164.208.19
    access-list ML_VPN extended permit ip host 115.111.99.129 host 209.164.192.126
    access-list Da_VPN extended permit ip host 10.9.124.100 host 10.125.81.88
    access-list Da_VPN extended permit ip host 10.9.124.101 host 10.125.81.88
    access-list Da_VPN extended permit ip host 10.9.124.102 host 10.125.81.88
    access-list Da_VPN extended permit ip host 10.9.124.100 10.125.81.0 255.255.255.0
    access-list Da_VPN extended permit ip host 10.9.124.101 10.125.81.0 255.255.255.0
    access-list Da_VPN extended permit ip host 10.9.124.102 10.125.81.0 255.255.255.0
    access-list Sr_PAT extended permit ip 10.10.0.0 255.255.0.0 any
    access-list Da_Pd_VPN extended permit ip host 10.9.124.100 10.125.80.64 255.255.255.192
    access-list Da_Pd_VPN extended permit ip host 10.9.124.100 10.125.64.0 255.255.240.0
    access-list Da_Pd_VPN extended permit ip host 10.9.124.100 host 10.125.85.46
    access-list Da_Pd_VPN extended permit ip host 10.9.124.100 host 10.125.86.46
    access-list Da_Pd_VPN extended permit ip host 10.9.124.101 10.125.80.64 255.255.255.192
    access-list Da_Pd_VPN extended permit ip host 10.9.124.101 10.125.64.0 255.255.240.0
    access-list Da_Pd_VPN extended permit ip host 10.9.124.101 host 10.125.85.46
    access-list Da_Pd_VPN extended permit ip host 10.9.124.101 host 10.125.86.46
    access-list Da_Pd_VPN extended permit ip host 10.9.124.102 10.125.80.64 255.255.255.192
    access-list Da_Pd_VPN extended permit ip host 10.9.124.102 10.125.64.0 255.255.240.0
    access-list Da_Pd_VPN extended permit ip host 10.9.124.102 host 10.125.85.46
    access-list Da_Pd_VPN extended permit ip host 10.9.124.102 host 10.125.86.46
    access-list XYZ_reliance extended permit ip 10.19.130.0 255.255.255.0 145.248.194.0 255.255.255.0
    access-list coextended permit ip host 2.2.2.2 host XXXXXXXX
    access-list coextended permit ip host XXXXXXXXhost 2.2.2.2
    access-list ci extended permit ip 10.1.134.0 255.255.255.0 208.75.237.0 255.255.255.0
    access-list ci extended permit ip 208.75.237.0 255.255.255.0 10.1.134.0 255.255.255.0
    access-list acl-outside extended permit ip host 57.66.81.159 host 172.17.10.3
    access-list acl-outside extended permit ip host 80.169.223.179 host 172.17.10.3
    access-list acl-outside extended permit ip any host 172.17.10.3
    access-list acl-outside extended permit tcp any host 10.10.1.45 eq https
    access-list acl-outside extended permit tcp any any eq 10000
    access-list acl-outside extended deny ip any any log
    pager lines 10
    logging enable
    logging buffered debugging
    mtu outside_rim 1500
    mtu XYZ_DMZ 1500
    mtu outside 1500
    mtu inside 1500
    ip local pool XYZ_c2s_vpn_pool 172.30.10.51-172.30.10.254
    icmp unreachable rate-limit 1 burst-size 1
    icmp permit any outside
    icmp permit any inside
    no asdm history enable
    arp timeout 14400
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-208.75.237.0 obj-208.75.237.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.7.0.0 obj-10.7.0.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-172.17.2.0 obj-172.17.2.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-172.17.3.0 obj-172.17.3.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-172.19.2.0 obj-172.19.2.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-172.19.3.0 obj-172.19.3.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-172.19.7.0 obj-172.19.7.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.1.0.0 obj-10.1.0.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.2.0.0 obj-10.2.0.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.3.0.0 obj-10.3.0.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.4.0.0 obj-10.4.0.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.6.0.0 obj-10.6.0.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.9.0.0 obj-10.9.0.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.11.0.0 obj-10.11.0.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-10.12.0.0 obj-10.12.0.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-172.19.1.0 obj-172.19.1.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-172.21.2.0 obj-172.21.2.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.1.134.0 obj-10.1.134.0 destination static obj-172.16.2.0 obj-172.16.2.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.19.130.201 obj-10.19.130.201 destination static obj-172.30.2.0 obj-172.30.2.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.19.130.201 obj-10.19.130.201 destination static obj-172.30.3.0 obj-172.30.3.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.19.130.201 obj-10.19.130.201 destination static obj-172.30.7.0 obj-172.30.7.0 no-proxy-arp route-lookup
    nat (inside,any) source static Serversubnet Serversubnet destination static XYZ_destinations XYZ_destinations no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.10.1.0 obj-10.10.1.0 destination static obj-10.2.0.0 obj-10.2.0.0 no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.19.130.0 obj-10.19.130.0 destination static obj-XXXXXXXX obj-XXXXXXXX no-proxy-arp route-lookup
    nat (inside,any) source static obj-10.19.130.0 obj-10.19.130.0 destination static obj-145.248.194.0 obj-145.248.194.0 no-proxy-arp route-lookup
    nat (inside,outside) source static obj-10.1.134.100 obj-10.9.124.100
    nat (inside,outside) source static obj-10.1.134.101 obj-10.9.124.101
    nat (inside,outside) source static obj-10.1.134.102 obj-10.9.124.102
    nat (inside,outside) source dynamic obj-10.8.108.0 interface
    nat (inside,outside) source dynamic obj-10.19.130.0 obj-115.111.99.129
    nat (inside,outside) source dynamic obj-10.1.134.0 obj-115.111.99.129 destination static obj-195.254.159.133 obj-195.254.159.133
    nat (inside,outside) source dynamic obj-10.1.134.0 obj-115.111.99.129 destination static obj-195.254.158.136 obj-195.254.158.136
    nat (inside,outside) source dynamic obj-10.1.134.0 obj-115.111.99.129
    nat (inside,outside) source dynamic obj-10.1.134.0 obj-115.111.99.129 destination static obj-209.164.192.0 obj-209.164.192.0
    nat (inside,outside) source dynamic obj-10.1.134.0 obj-115.111.99.129 destination static obj-209.164.208.19 obj-209.164.208.19
    nat (inside,outside) source dynamic obj-10.1.134.0 obj-115.111.99.129 destination static obj-209.164.192.126 obj-209.164.192.126
    nat (inside,outside) source dynamic obj-10.8.100.128 obj-115.111.99.130
    nat (inside,outside) source dynamic obj-10.10.0.0 obj-115.111.99.132
    nat (inside,outside) source static obj-10.10.1.45 obj-115.111.99.133
    nat (inside,outside) source dynamic obj-10.99.132.0 obj-115.111.99.129
    object network obj-172.17.10.3
    nat (XYZ_DMZ,outside) static 115.111.99.134
    access-group acl-outside in interface outside
    route outside 0.0.0.0 0.0.0.0 115.111.23.129 1
    route outside 0.0.0.0 0.0.0.0 115.254.127.130 10
    route inside 10.10.0.0 255.255.0.0 10.8.100.1 1
    route inside 10.10.1.0 255.255.255.0 10.8.100.1 1
    route inside 10.10.5.0 255.255.255.192 10.8.100.1 1
    route inside 10.8.100.128 255.255.255.128 10.8.100.1 1
    route inside 10.8.108.0 255.255.255.0 10.8.100.1 1
    route inside 10.19.130.0 255.255.255.0 10.8.100.1 1
    route inside 10.99.4.0 255.255.255.0 10.99.130.254 1
    route inside 10.99.132.0 255.255.255.0 10.8.100.1 1
    route inside 10.1.134.0 255.255.255.0 10.8.100.1 1
    route outside 208.75.237.0 255.255.255.0 115.111.23.129 1
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    aaa authentication telnet console LOCAL
    aaa authorization command LOCAL
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec ikev1 transform-set vpn2 esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set vpn6 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set vpn5 esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set vpn7 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set vpn4 esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set vpn1 esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set vpn_reliance esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set c2s_vpn esp-3des esp-md5-hmac
    crypto ipsec security-association lifetime seconds 86400
    crypto dynamic-map dyn1 1 set ikev1 transform-set c2s_vpn
    crypto dynamic-map dyn1 1 set reverse-route
    crypto map vpn 1 match address XYZ
    crypto map vpn 1 set peer XYZ Peer IP
    crypto map vpn 1 set ikev1 transform-set vpn1
    crypto map vpn 1 set security-association lifetime seconds 3600
    crypto map vpn 1 set security-association lifetime kilobytes 4608000
    crypto map vpn 2 match address NE
    crypto map vpn 2 set peer NE_Peer IP
    crypto map vpn 2 set ikev1 transform-set vpn2
    crypto map vpn 2 set security-association lifetime seconds 3600
    crypto map vpn 2 set security-association lifetime kilobytes 4608000
    crypto map vpn 4 match address ML_VPN
    crypto map vpn 4 set pfs
    crypto map vpn 4 set peer ML_Peer IP
    crypto map vpn 4 set ikev1 transform-set vpn4
    crypto map vpn 4 set security-association lifetime seconds 3600
    crypto map vpn 4 set security-association lifetime kilobytes 4608000
    crypto map vpn 5 match address XYZ_global
    crypto map vpn 5 set peer XYZ_globa_Peer IP
    crypto map vpn 5 set ikev1 transform-set vpn5
    crypto map vpn 5 set security-association lifetime seconds 3600
    crypto map vpn 5 set security-association lifetime kilobytes 4608000
    crypto map vpn 6 match address Da_VPN
    crypto map vpn 6 set peer Da_VPN_Peer IP
    crypto map vpn 6 set ikev1 transform-set vpn6
    crypto map vpn 6 set security-association lifetime seconds 3600
    crypto map vpn 6 set security-association lifetime kilobytes 4608000
    crypto map vpn 7 match address Da_Pd_VPN
    crypto map vpn 7 set peer Da_Pd_VPN_Peer IP
    crypto map vpn 7 set ikev1 transform-set vpn6
    crypto map vpn 7 set security-association lifetime seconds 3600
    crypto map vpn 7 set security-association lifetime kilobytes 4608000
    crypto map vpn interface outside
    crypto map vpn_reliance 1 match address XYZ_rim
    crypto map vpn_reliance 1 set peer XYZ_rim_Peer IP
    crypto map vpn_reliance 1 set ikev1 transform-set vpn_reliance
    crypto map vpn_reliance 1 set security-association lifetime seconds 3600
    crypto map vpn_reliance 1 set security-association lifetime kilobytes 4608000
    crypto map vpn_reliance interface outside_rim
    crypto map mymap 1 ipsec-isakmp dynamic dyn1
    crypto isakmp identity address
    no crypto isakmp nat-traversal
    crypto ikev1 enable outside_rim
    crypto ikev1 enable outside
    crypto ikev1 policy 1
    authentication pre-share
    encryption aes-256
    hash sha
    group 5
    lifetime 28800
    crypto ikev1 policy 2
    authentication pre-share
    encryption aes-256
    hash sha
    group 5
    lifetime 86400
    crypto ikev1 policy 4
    authentication pre-share
    encryption aes-256
    hash sha
    group 5
    lifetime 28000
    crypto ikev1 policy 5
    authentication pre-share
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 100
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 43200
    crypto ikev1 policy 65535
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet 10.8.100.0 255.255.255.224 inside
    telnet timeout 5
    ssh timeout 5
    ssh key-exchange group dh-group1-sha1
    console timeout 0
    no threat-detection basic-threat
    no threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    group-policy XYZ_c2s_vpn internal
    username testadmin password oFJjANE3QKoA206w encrypted
    tunnel-group XXXXXXXX type ipsec-l2l
    tunnel-group XXXXXXXX ipsec-attributes
    ikev1 pre-shared-key *****
    tunnel-group XXXXXXXXtype ipsec-l2l
    tunnel-group XXXXXXXXipsec-attributes
    ikev1 pre-shared-key *****
    tunnel-group XXXXXXXX type ipsec-l2l
    tunnel-group XXXXXXXX ipsec-attributes
    ikev1 pre-shared-key *****
    tunnel-group XXXXXXXX type ipsec-l2l
    tunnel-group XXXXXXXX ipsec-attributes
    ikev1 pre-shared-key *****
    tunnel-group XXXXXXXX type ipsec-l2l
    tunnel-group XXXXXXXX ipsec-attributes
    ikev1 pre-shared-key *****
    tunnel-group XXXXXXXX type ipsec-l2l
    tunnel-group XXXXXXXX ipsec-attributes
    ikev1 pre-shared-key *****
    tunnel-group XXXXXXXX type ipsec-l2l
    tunnel-group XXXXXXXX ipsec-attributes
    ikev1 pre-shared-key *****
    tunnel-group XYZ_c2s_vpn type remote-access
    tunnel-group XYZ_c2s_vpn general-attributes
    address-pool XYZ_c2s_vpn_pool
    tunnel-group XYZ_c2s_vpn ipsec-attributes
    ikev1 pre-shared-key *****
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect netbios
      inspect rsh
      inspect rtsp
      inspect skinny 
      inspect esmtp
      inspect sqlnet
      inspect sunrpc
      inspect tftp
      inspect sip 
      inspect xdmcp
      inspect icmp
      inspect ip-options
    service-policy global_policy global
    privilege show level 3 mode exec command running-config
    privilege show level 3 mode exec command logging
    privilege show level 3 mode exec command crypto
    prompt hostname context
    no call-home reporting anonymous
    call-home
    profile CiscoTAC-1
      no active
      destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
      destination address email [email protected]
      destination transport-method http
      subscribe-to-alert-group diagnostic
      subscribe-to-alert-group environment
      subscribe-to-alert-group inventory periodic monthly
      subscribe-to-alert-group configuration periodic monthly
      subscribe-to-alert-group telemetry periodic daily
    Cryptochecksum:caa7476cd348ed89b95d37d4e3c9e1d8
    : end
    XYZ#

    Thanks Javier.
    But i have revised the VPN confuration. Below are the latest configs. with this latest configs. I'm getting username & password screen while connecting cisco vpn client software. once we entered the login credential. it shows "security communication channel" then it goes to "not connected" state. Can you help me to fix this.
    access-list ACL-RA-SPLIT standard permit host 10.10.1.3
    access-list ACL-RA-SPLIT standard permit host 10.10.1.13
    access-list ACL-RA-SPLIT standard permit host 10.91.130.201
    access-list nonat line 1 extended permit ip host 10.10.1.3 172.30.10.0 255.255.255.0
    access-list nonat line 2 extended permit ip host 10.10.1.13 172.30.10.0 255.255.255.0
    access-list nonat line 3 extended permit ip host 10.91.130.201 172.30.10.0 255.255.255.0
    ip local pool CO-C2S-VPOOL 172.30.10.51-172.30.10.254 mask 255.255.255.0
    group-policy CO-C2S internal
    group-policy CO-C2S attributes
    vpn-tunnel-protocol IPSec
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list vlauel ACL-RA-SPLIT
    dns-server value 10.10.1.3
    tunnel-group TUN-RA-SPLIT type remote-access
    tunnel-group TUN-RA-SPLIT general-attributes
    default-group-policy CO-C2S
    address-pool CO-C2S-VPOOL
    tunnel-group TUN-RA-SPLIT ipsec-attributes
    pre-shared-key sekretk3y
    username ra-user1 password passw0rd1 priv 1
    group-policy CO-C2S internal
    group-policy CO-C2S attributes
    vpn-tunnel-protocol IPSec
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list vlauel ACL-RA-SPLIT
    dns-server value 10.10.1.3
    tunnel-group TUN-RA-SPLIT type remote-access
    tunnel-group TUN-RA-SPLIT general-attributes
    default-group-policy CO-C2S
    address-pool CO-C2S-VPOOL
    tunnel-group TUN-RA-SPLIT ipsec-attributes
    pre-shared-key *********
    username ******* password ******** priv 1
    crypto ipsec transform-set 3DES esp-3des esp-sha-hmac
    crypto dynamic-map dynmap 10 set transform-set 3DES
    crypto map Outside_Map 500 ipsec-isakmp dynamic dynmap
    crypto isakmp identify address
    crypto isakmp enable outside
    crypto isakmp policy 100
    authentication pre-share
    encr 3des
    hash sha
    crypto ipsec transform-set 3DES esp-3des esp-sha-hmac
    crypto dynamic-map dynmap 10 set transform-set 3DES
    crypto map Outside_Map 500 ipsec-isakmp dynamic dynmap
    crypto map vpn interface outside
    crypto isakmp identify address
    crypto isakmp enable outside
    crypto isakmp policy 100
    authentication pre-share
    encr 3des
    hash sha
    group 1
    lifetime 3600

Maybe you are looking for

  • Changes to write optimized DSO containing huge amount of data

    Hi Experts, We have appended two new fields in DSO containg huge amount of data. (new IO are amount and currency) We are able to make the changes in Development (with DSO containing data).  But when we tried to tranport the changes to our QA system,

  • IP Communicator (SCCP) over VPN

    Hi, Using router WRT54GS, with firmware 7.50.8. I use VPN version 5 to connect to the office. The only thing not working is IP Communicator (SCCP protocol). I can access the callmanager web page, setup the phone. The phone gets the locales and all th

  • FAX setup problem with Officejet 6700 Premium

    Windows 7, setting up my 6700 wirelessly.  If I have my printer connected directly to my Vonage device, no problems setting up FAX.  If I then connect an extension phone to the second connection (2-EXT), it no longer works.  I get a message indicatin

  • Writing a custom component with multiple fields.

    Does anyone have some pointers on writing a custom component that properly handles multiple input fields? An example usage might be as follows: Assume the following java classes: public interface Address {     //... getters/setters for Address. publi

  • I can not store more than 7 gb data in my ipod classic 7 gen 120gb

    i can not store more than 7 gb data in my ipod classic 7 gen 120gb