Cisco ASR 9010 Copper port problem

Recently we have purchased Cisco ASR 9010 router. We have setup a 1Gbps copper based SFP module in the line card. It detect the module and I have found this by using show controller. But when I coonect a RJ-45 cable between thre router and my laptop, port do not up, even I connect the cable to a cisco switch that time also it is not working. Is there any command to up this port!
Please help.
Regards,
Shuvo

You likely need "negotiation auto" configured under this port, as many devices have autonegotiation enabled by default but the ASR9000 does not. The "media-type" command is not present on the ASR9000 as it's used to switch between SFPs and fixed copper ports - not for copper SFPs.

Similar Messages

  • Cisco pix 501 open port problem

    Hi,
    I'm running a Pix 501 for Home office and I want to open first ports for my mail client for an outside located server.
    But i get following error in the log:
    106023: Deny tcp src outside:<ipmailserver>/993 dst inside:<ipoutsideinterface>/1729 by access-group "outside-mail"
    here's my basic config:
    PIX Version 6.3(3)
    interface ethernet0 auto
    interface ethernet1 100full
    nameif ethernet0 outside security0
    nameif ethernet1 inside security100
    enable password YYYYYY encrypted
    passwd YYYYYY encrypted
    hostname sunny
    domain-name ciscopix.com
    fixup protocol dns maximum-length 512
    fixup protocol ftp 21
    fixup protocol h323 h225 1720
    fixup protocol h323 ras 1718-1719
    fixup protocol http 80
    fixup protocol ils 389
    fixup protocol pptp 1723
    fixup protocol rsh 514
    fixup protocol rtsp 554
    fixup protocol sip 5060
    fixup protocol sip udp 5060
    fixup protocol skinny 2000
    no fixup protocol smtp 25
    fixup protocol sqlnet 1521
    fixup protocol tftp 69
    names
    access-list outside-mail permit tcp any any eq 465
    access-list outside-mail permit tcp any any eq 993
    pager lines 24
    logging on
    logging monitor emergencies
    logging buffered informational
    mtu outside 1500
    mtu inside 1500
    ip address outside dhcp setroute
    ip address inside 192.168.10.254 255.255.255.0
    ip audit info action alarm
    ip audit attack action alarm
    pdm logging informational 100
    pdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 1 192.168.10.0 255.255.255.0 0 0
    access-group outside-mail in interface outside
    timeout xlate 0:05:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
    timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
    timeout uauth 0:05:00 absolute
    aaa-server TACACS+ protocol tacacs+
    aaa-server RADIUS protocol radius
    aaa-server LOCAL protocol local
    no snmp-server location
    no snmp-server contact
    snmp-server community public
    no snmp-server enable traps
    floodguard enable
    telnet 192.168.10.0 255.255.255.0 inside
    telnet timeout 5
    ssh 192.168.10.0 255.255.255.0 inside
    ssh timeout 60
    console timeout 0
    dhcpd address 192.168.10.10-192.168.10.39 inside
    dhcpd lease 3600
    dhcpd ping_timeout 750
    dhcpd auto_config outside
    dhcpd enable inside
    username stefan password YYYYY encrypted privilege 2
    terminal width 80
    Cryptochecksum:
    : end
    [OK]
    What's the problem?
    Any recommondations for the config anyway?
    Thanks

    Thanks Gerhard for the answer, but i don't want to redirect the port to an inside mail server.
    I try to connect to an outside mail server with a mail client from an inside pc (who is in the dhcp ip pool, i.e. 192.168.10.22).
    to open the ports i added:
    access-list outside-mail permit tcp any any eq 465
    access-list outside-mail permit tcp any any eq 993
    access-group outside-mail in interface outside
    but why is there a deny because of the access-group in the log?
    106023: Deny tcp src outside:/993 dst inside:/1729 by access-group "outside-mail"
    Regards S.

  • Ask the Experts: Understanding Cisco ASR 9000 Series Aggregation Services Routers Platform Architecture and Packet Forwarding Troubleshooting

    With Xander Thuijs
    Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn how to Cisco ASR 9000 Series Aggregation Services Routers with Cisco expert Xander Thuijs. The Cisco ASR 9000 Series Aggregation Services Routers product family offers a significant added value compared to the prior generations of carrier Ethernet routing offerings. The Cisco ASR 9000 Series is an operationally simple, future-optimized platform using next-generation hardware and software. The ASR 9000 platform family is composed of the Cisco ASR 9010 Router, the Cisco ASR 9006 Router, the Cisco ASR 9922 Router, Cisco ASR 9001 Router and the Cisco ASR 9000v Router.
    This is a continuation of the live Webcast.
    Xander Thuijs is a principal engineer for the Cisco ASR 9000 Series and Cisco IOS-XR product family at Cisco. He is an expert and advisor in many technology areas, including IP routing, WAN, WAN switching, MPLS, multicast, BNG, ISDN, VoIP, Carrier Ethernet, System Architecture, network design and many others. He has more than 20 years of industry experience in carrier Ethernet, carrier routing, and network access technologies. Xander  holds a dual CCIE certification (number 6775) in service provider and voice technologies. He has a master of science degree in electrical engineering from Hogeschool van University in Amsterdam.
    Remember to use the rating system to let Xander know if you have received an adequate response.
    Xander might not be able to answer each question because of the volume expected during this event. Remember that you can continue the conversation on the Service Providers community XR OS And Platforms  shortly after the event. This event lasts through Friday, May 24, 2013. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.
    Webcast  related links:
    Slides
    Webcast  Video Recording
    FAQ

    Is there a Cisco lab available for ASR 9000
    we have "XR4U" stations coming available soon when XR 511 comes alive. The plan is for a downloadable play image like that. In the interim we have 2 demo systems available, and they can be booked via your account manager representative.
    How will MOD160 perform with multiple 9000NVS?
    very well. the mod 160 has 4 NPU's, 2 per bay. So if you have a 4x10 MPA to serve a satellite, you effectively have a single NPU per 20 1Gigs from the satellite. The pps performance will be stellar. However it might be price technically more ideal to connect satellite with a 36x10. Since the MOD-x has native MPA's with 1G also.
         2. Is there a shortcut for a Bundle-EthernetX interface, such as port-channel interface (poX), in Cisco IOS® ?.
    usability enhancement is there, we are trying to push this into a new reasonable release. follow CSCuh04526
         3. What  is the revolutions per minute (RPM) on these hard disk drives (HDDs)  compared to the solid state drives (SDDs)? Will the spinning drives be  slow?
    depends on the type we had avaialble at time of production, you will see different sizes and disks on the RSP2. the rpm of the HD is not so much an issue as much as the buffered writing we used to do in XR. This is fixed up with XR43 where the disk writing performance is much better. the HD/SDD is used for logging storage only (and maybe your pictures) but other then that we're not that concerned with write perf of the HD.
    regards
    xander

  • IPv6 on ASR 9010

    Which IPv6 features are available on the Cisco ASR 9010 platform and is there a specific license/line card needed?
    Thanks
    Manuel

    Hi Manuel,
    there's no need in a specific card and therefore in a license. The list of features is big and most of core ones is there, and it is growing! It would be better to check feature by feature to learn whether it will suit your requirements.
    For all further questions please do use the newly created forum for IOX -
    https://supportforums.cisco.com/community/netpro/service-providers/ios-xr?view=discussions
    See you there!
    Regards,
    Ivan.

  • How to disable AUX port in ASR 9010

    Hi All,
    How to disable the AUX port in ASR 9010. Inside "line aux" I can't configure anything except "login authentication" (which is used for aaa authentication).
    Also after IOS XR 3.2 the configuration for AUX port has been removed
    Platform used: ASR 9010
    Version: IOS-XR 4.1.2
    Best Regards
    Saikat Chakraborty

    Hi Saikat,
    AUX has the same authentication method as we have on the system.  From this perspective, AUX is protected the same way as the Console port and only those who have an account can login via AUX (same way as via console). Any attempts to log on AUX will be logged:
    Successful:
    ksh[65902]: Successfully authenticated user 'XXX' for ksh access via 'aux' on '0/RSP0/CPU0'
    Incorrect:
    ksh[65902]: Failed authentication attempt by user 'YYY' for ksh access via 'aux' on '0/RSP0/CPU0
    But if anyone has a physical access to the device, that would be even bigger threat compare to system protected AUX login.
    BTW, tacacs authentication should work for AUX too. We’d need to define a template for it.
    Example:
    aaa authentication login tacacs_template group tacacs+ local
    line template aux
          login authentication tacacs_template
    Regards,
    /A

  • ASR 9010 licensing question

    Hi,
    any good cisco reference for installing licenses for ASR 9010 router?
    we need to "move" license to oper state
    (admin)#sho license
    Mon May 28 15:44:08.686 UTC
    FeatureID: A9K-AIP-LIC-B (Slot based, Permanent) 
      Total licenses 2
      Available for use         2
      Allocated to location     0
      Active                    0
      Store name             Permanent
      Store index               1
        Pool: Owner
          Total licenses in pool: 2
          Status: Available     2    Operational:    0
    thanks for help
    miro

    I have the same problem on asr 9001. A can't activate license regardless of the location.
    (admin)#sh license
    FeatureID: A9K-9001-AIP-LIC (Slot based, Permanent)
      Total licenses 1
      Available for use         1
      Allocated to location     0
      Active                    0
      Store name             Permanent
      Store index               1
        Pool: Owner
          Total licenses in pool: 1
          Status: Available     1    Operational:    0
    license A9K-9001-AIP-LIC
     location 0/RSP0/CPU0
    (admin)#sh platform
    Wed Oct  1 14:45:47.427 CEST
    Node            Type                      State            Config State
    0/RSP0/CPU0     ASR9001-RP(Active)        IOS XR RUN       PWR,NSHUT,MON
    0/FT0/SP            ASR-9001-FAN-V2           READY
    0/0/CPU0            ASR9001-LC                IOS XR RUN       PWR,NSHUT,MON
    0/0/0                  A9K-MPA-4X10GE            OK               PWR,NSHUT,MON
    0/0/1                 A9K-MPA-20X1GE            OK               PWR,NSHUT,MON
    0/PM0/SP        A9K-750W-AC               READY            PWR,NSHUT,MON
    0/PM1/SP        A9K-750W-AC               FAILED           PWR,NSHUT,MON
    Any suggestion?
    Regards,
    Nenad

  • Cisco ASR 9006 IOS XR 4.3.0 aaa authorization

    Hi,
    I've configured two Cisco ASR 9006 with IOS XR 4.3.0 with the aaa. I've a problem with the authorization statement.
    I need to distiguish two groups.
    Network Administrator (Full access, show, configuration etc etc)
    Network Viewer (Users in this group can use only the show command)
    I cannot find anything clear on the documentation. Can you help me?
    Below the actual configuration (without authorization)
    tacacs source-interface Loopback0 vrf default
    tacacs-server host 10.10.10.1 port 49
    tacacs-server key 7 XXXXXXXXXX
    tacacs-server timeout 10
    username emergency
    group netadmin
    password 7 XXXXXXXXXXXXXXX
    aaa accounting exec default start-stop group ACS
    aaa accounting system default start-stop group ACS
    aaa group server tacacs+ ACS
    server 10.10.10.1
    aaa authentication login default group ACS local
    I have configured two Shell Command Authorization Sets in my ACS. One for ReadOnly and one for Full Access.
    The ReadOnly Group (called AccessoSolaLettura) is on the attacched png called asr_1.PNG
    The Full Access Group (called AccessCompleto) is on the attached png called asr_2.PNG
    I associated this Shell Authorization sets to two users group. (Network Administrator and Network Viewer).
    The first one with Level 15 and the second one with Level 7. (Attached file ACS_1.png and ACS_2.png)
    Can you tell me if the ACS configuration is right and which configuration is needed on the ASR?
    The ACS Release is 4.2(0) Build 124.
    Tnx
    Leonardo

    Hi Leonardo,
    In XR we have the concept of tasks and taskgroup for determining what a user can do, and we recommend using this. For tasks we have the read/write/execute/debug permissions.
    For instance to run 'show bgp summary' we need the read permission on the task BGP. Instead of assigning individual permissions per user we can create a taskgroup and the user can inherit everything from a taskgroup.
    So for instance we can add read BGP, read OSPF, and read system to the taskgroup test. We can then have the user inherit the taskgroup test and get all the permissions that taskgroup has. We can inherit multiple tasks and taskgroups.
    In addition we have some predefined task groups (for the full access user you will want the cisco-support and root-system taskgroups).
    You can find some more information in the following posts
    http://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/asr9k_r4-3/security/configuration/guide/b_syssec_cg43xasr9k/b_syssec_cg43asr9k_chapter_010.html
    https://supportforums.cisco.com/docs/DOC-15944
    HTH,
    Sam

  • Traffic policing question on Cisco ASR 1001

    Hi Experts,
    I have a request to setup aggregated traffic policing on a Cisco ASR 1001 router for multiple networks within a router.
    Lets say I have a router with several subinterfaces:
    interface GigabitEthernet0/2
     description WAN
     ip address x.x.x.x x.x.x.x
    interface GigabitEthernet0/1.70
     description Lan_1
     encapsulation dot1Q 70
     ip address 192.168.55.1 255.255.255.0
    interface GigabitEthernet0/1.80
     description LAN_2
     encapsulation dot1Q 80
     ip address 192.168.56.1 255.255.255.0
    interface GigabitEthernet0/1.90
     description Servers
     encapsulation dot1Q 90
     ip address 172.16.10.1 255.255.255.0
    I have a WAN link 100Mbit/s and I need to police traffic, so that I have 30Mbit/s for servers (GigabitEthernet0/1.90) and the rest 70Mbit I want to share between Interface Lan_1 and LAN_2. The Idea is that I need 70Mbit/s equally shared between two interfaces, so that I have fair policing on both iunterfaces. What is the best way to achieve this?
    Many Thanks

    Hello
    The below configuration is a possible option, Its provides policing inbound from the clients interfaces and LLQ priority queung on the wan interface for the servers and  shaping values from LAN1 & 2 traffic is set to 35MB.each.
    Notice nothing is defined for the default class, however i am on the understanding this is given by default 1% of Hqos implementations.
    Maybe others on here could review to verify any problems with this post and share their thoughts?
    ip access-list extended SRVS_acl
     permit ip 172.16.10.0 0.0.0.255 any
    ip access-list extended LAN1_acl
     permit ip 192.168.55.0 0.0.0.255 any
    ip access-list extended LAN2_acl
     permit ip 192.168.56.0 0.0.0.255 any
    class-map match-all SRVS_CM
     match access-group name SRVS_acl
    class-map match-all LAN_1_CM
     match access-group name  LAN1_acl
    class-map match-all LAN_2_CM
     match access-group name LAN2_acl
    policy-map SRVS_PM
     class SRVS_CM
        police 30720000 conform-action transmit exceed-action drop
    policy-map LAN_2_PM
     class LAN_2_CM
        police 35840000 conform-action transmit 
    policy-map LAN_1_PM
     class LAN_1_CM
        police 35840000 conform-action transmit 
    interface GigabitEthernet0/1.70
    service-policy input LAN_1_PM
    interface GigabitEthernet0/1.90
     service-policy input SRVS_PM
    interface GigabitEthernet0/1.80
     service-policy input LAN_2_PM
    policy-map WAN_CHILD
     class SRVS_CM
      priority 30720
     class LAN_1_CM
      shape average 35840000
     class LAN_2_CM
      shape average 35840000
     class class-default
      fair-queue
    policy-map WAN_PARENT
     class class-default
      shape average 102400000
      service-policy WAN_CHILD
    int  GigabitEthernet0/2
    bandwidth 102400
    service-policy output WAN_PARENT
    res
    Paul

  • Cisco ASR Router Software Version 4.3.1 // PRTG Custom Sensor

    Dears,
    We are encountering problem in doing costume SNMP sensors in PRTG, whenever I create a customized sensor, the sensor goes up and down.  We have faced this problem after updating the software of our Cisco ASR to 4.3.1. In older versions, it was working well.  Is there a problem in Cisco ASR 4.3.1 SNMP with PRTG ? I would appreciate it if you can support in this case as we are in need of these customized sensors. We have gor  all of them down because of the update
    Regards,

    Dear Alexander,
    The standard sensors of PRTG are working well such as traffic sensors, ping etc, but the customized sensors are not working well in version 4.3.1. I always do a customized sensors for QoS, SLAs and others and they are working well in versions below 4.3.1.
    Furthermore, I have tested those OIDs by using Paessler SNMP Tester and I have seen that the reading is not showing properly. For instance, I have a customized OID that shows the reading every 60s (as a minimum) only while in older versions of ASR software I can see the reading every 30s or below of that particular OID using the same version of PRTG!
    Conclusion:
    PRTG latest version + ASR 4.3.1 = Customized sesnors are not working well
    PRTG latest version + ASR Older version = Customized sesnors are working well
    Kind regards,

  • Cisco ASR - How to connect an OTV internal interface to a FabricPath domain

    Scenario - migrate servers while maintaining their existing IP address from data centre 1 to data centre 2 with minimal downtime. Diagram attached.
    I'm planning on using a Cisco ASR1001-X with AES license at DC1 and DC2 and configuring the routers with OTV to extend 10 x VLANs between the data centres. The join interface would connect directly to the WAN circuit NTU and the Internal Interface would connect to the switch and be configured as a service instance with 10 VLANs tagged using dot1q. The problem is that DC1 switch infrastructure is using Cisco Nexus 56xx configured with FabricPath. I can't find any information that suggests that i can patch the Cisco ASR router's internal interface directly into a FabricPath switchport or what the configuration would be.
    Older OTV documentation refers to Nexus 7000 and OTV stating the following: "Because OTV encapsulation is done on M-series modules, OTV cannot read FabricPath packets. Because of this restriction, terminating FabricPath and reverting to Classical Ethernet where the OTV VDC resides is necessary."
    Is this true for the Cisco ASR also? The only workaround i can think of is to install a cheap catalyst switch connected to the FabricPath domain and re-introduce spanning-tree at the edge but this seems backwards to me. Any help or suggestions appreciated? Thanks

    Thanks Minh,
    So it is possible to have switchports configured as routed, fabricpath and trunk/access in a fabricpath configuration? Do i need to add any spanning-tree pseudo or priority configuration?
    Sample configs:
    #ASR
    interface GigabitEthernet0/0/1
     no ip address
     service instance 1 ethernet
      encapsulation dot1q 1
      bridge-domain 1
     service instance 2 ethernet
      encapsulation dot1q 2
      bridge-domain 2
     service instance 3 ethernet
      encapsulation dot1q 3
      bridge-domain 3
    #Nexus 56xx
    interface e1/5
      switchport mode trunk
      switchport trunk allow vlan 1,2,3

  • Maximum cos1 (voice traffic) supported by Cisco ASR 1006 router

    Dear Team,
    Please confirm the maximum cos 1 traffic supported by cisco ASR 1006 router.

    Yes, it would. If you are planning on terminating a single site on this router I would spread over multiple routers for redundancy.
    Table 6 explains number of ports and channels providing you have the DSPs: 
    http://www.cisco.com/c/dam/en/us/products/collateral/routers/2800-series-integrated-services-routers-isr/product_data_sheet0900aecd8057f2e0.pdf

  • Cisco ASR 1006 and WAAS

    Hi,
    Is there any built-in WAAS and NME features or services in Cisco ASR 1006? Or is there any WAAS or NME module that can be installed in Cisco ASR 1006? I found that for Cisco ISR 1900, 2900, and 3900, WAAS and NME services can be enabled by installing SRE and NME module. But can't find any information for Cisco ASR 1006.
    Really appreciate your help.
    Thanks

    Hi Marvin
    There is no option for this.
    on the 4510 the only options under the interface are
    speed nonegotiate or no speed nonegotiate (for auto)
    Similarly on the ASR no negotiation auto or negotiation auto. setting each device to auto/manual or manual/auto has no effect on the ASR port - its still down
    Cheers

  • PPPoGEC Cisco ASR 1001

    Hi Cisco Professional,
    We want to implementing PPPoE over port-channel (using subinterfaces L2) in Cisco ASR 1001 routers, my question is if this router support this feature?, in the other hand i've see  documents about this theme, pls check these links:
    http://www.cisco.com/en/US/docs/ios/ios_xe/cether/configuration/guide/ce_lnkbndl_xe.html
    http://www.cisco.com/en/US/docs/ios-xml/ios/cether/configuration/xe-3s/ce-ieee-link-bndl-xe.html
    My IOS version Cisco ASR 1001 is:
    System image file is "bootflash:/asr1001-universalk9.03.04.00.S.151-3.S.bin"
    We want this configuration on the router,
    no     interface     GigabitEthernet0/0/0.25
    interface     port-channel     10.25
    description     TURBONETT     PUBLICA     UT
    encapsulation     dot1Q     25
    ip     address     10.17.44.254     255.255.252.0
    no     interface     GigabitEthernet0/0/0.52
    interface     port-channel     10.52
    description     TURBONETT-UT
    encapsulation     dot1Q     52
    pppoe     enable     group     global
    pppoe     max-sessions     4000
    no     interface     GigabitEthernet0/0/0.61
    interface     port-channel     10.61
    description     Turbonett-Sector-A
    encapsulation     dot1Q     61
    pppoe     enable     group     global
    pppoe     max-sessions     4000
    Kind Regards,
    Renzo Tovar

    Hi Renzo,
    PPPoEoVLAN on GEC (LACP mode) is supported as of XE 3.7. I see that you are using XE 3.4 here so I would suggest to move to XE 3.7 and try this feature.
    This is a sample configuration for the feature:
    interface GigabitEthernet2/1/0
    no ip address
    negotiation auto
    channel-group 2 mode active
    interface GigabitEthernet3/1/0
    no ip address
    negotiation auto
    channel-group 2 mode active
    lacp port-priority 65000
    interface Port-channel2
    no ip address
    load-interval 30
    no negotiation auto
    lacp max-bundle 1
    lacp fast-switchover
    interface Port-channel2.200
    encapsulation dot1Q 200
    pppoe enable group global
    interface Port-channel2.500
    encapsulation dot1Q 500 second-dot1q 1500
    pppoe enable group global
    As you can see, both PPPoEoVLAN and  PPPoEoQinQ are supported.
    Hope this helps.
    Best regards.

  • ASR 9010 SNMP detail

    Hi Everyone,
    This is my first post in this CISCO community, so again HELLO.
    Regarding the SNMP traps in ASR 9010 (I use IOS-XR:4.1.2), which trap is used to get notifications when the transceiver power is low or below the threshold, also is there a document which explains what each trap does(in detail)? I have already read the
    "Cisco ASR 9000 Series Aggregation Services Router System Management Command Reference, Release 4.1"  which was good but not so informative on the topic of SNMP.
    Best Regards
    Saikat

    Hi,
    Is there a way of changing the default threshold value "entSensorThreshold Table"? If so whats the procedure.
    Im using XFP-10GER-192IR+ for inter-site connection.
    For eg.
    The output of  "show controllers te phy"
    Thresholds:                    Alarm High                   Warning High                              Warning Low                                        Alarm Low
                  Temperature:               83.000                 80.000                                     -10.000                                                -13.000
                      Voltage:           0.000 Volt                   0.000 Volt                                0.000 Volt                                            0.000 Volt
                         Bias:        130.000 mAmps              120.000 mAmps                       20.000 mAmps                                     10.000 mAmps
               Transmit Power:  5.012 mW (7.00 dBm)       2.512 mW (4.00 dBm)              0.339 mW (-4.70 dBm)                          0.170 mW (-7.70
                Receive Power:  1.585 mW (2.00 dBm)       0.794 mW (-1.00 dBm)             0.026 mW (-15.80 dBm)                         0.013 mW (-18.
    Will these values be referred by the entity-sensor MIB or the default ones "entSensorThreshold Table"
    which are mentioned inside the MIB specification guide will be used?
    Thanks in advance.
    Best Regards
    Saikat
    Message was edited by: Saikat Chakraborty

  • Port Problem, cant Recieve Mail

    Hi
    Just recently my mail has stopted working due to a port problem. By my inbox i get a small icon which is a triangle with an explanation mark in. When i click it the first message i get is:
    *Connection Failed*
    +There may be a problem with the mail server or network. Check the settings for account "POP Account" or try again.+
    +The server error encountered was: The connection to host mail.kahane.co.uk on port 110 failed.+
    Then it willl give me a chice to go offline or online, ill click online and the icon is still there so i click the icon again and the second message i get is:
    Alert
    +There may be a problem with the mail server or network. Check the settings for account "POP Account" or try again.+
    +The server error encountered was: The connection to host mail.kahane.co.uk on port 110 failed.+
    I haven't changed any settings in the preferances or done anything which may have caused this. Incase you need to know i am on a POP account.
    I would much appreciate any help, thanks

    Me too... it comes and goes. It all started when I got a wireless router.

Maybe you are looking for

  • How do I use Time Capsule as a wireless router and turn my current one into modem only

    I have a crappy modem/ router and before I purchase a new modem I want to use the modem (no wireless) feature of my router. Question #1 How do I use my Time Capsule as a router? Question #2 If I do this will I still be able to wirelessly back up to m

  • KF fixing in SCM 7.0

    Hi, I have  a KF which is maintained as fixable in PA and also has been assigned a 9AADDKF1 with a calc  type P. 9AADDKF1 has a fixed KF 9ADPDANT. When  I try to fix a KF in planning book, I can fix only at "Total" and not at detail level. Even the f

  • Webcenter content IPM error

    Hi, In Webcenter Imaging I have the Application security rights(create and administrator in Manage security). when I try to modify a application its going fine till application security but in document security page when i try to click next without c

  • Apache multiple sites not directing properly

    Having a problem with multiple sites (domains) on my Snow Leopard Server.  I have three sites (with three separate registered domain names).  Two work fine and intentionally point to the same site (call it DomainA.com and DomainA.net).  The third one

  • Multiple insert row.

    Hi all, I have a table "Test" with the following column "X", "X2" and "X3". In apex a form on a table is created and I want to do a multiple insert on that table. Can anyone help me with this problem???