Cisco asr1000 aux-port
Hi. I have a Cisco ASR 1006 Router, with the the aux-port connected but i can´t configure the "line aux 0".. the line does not exist in the running config.
http://www.cisco.com/c/en/us/td/docs/routers/asr1000/install/guide/asr1routers/asr1higV8/asr1_hw2.html
In the related link Cisco says "The AUX port is a diagnostics access port".
I need to connect Cisco ASR1000 Aux-port with a Cisco CRS Console-Port as a second remote control method.
I Wish to confirm this before deploy several sites in the same way.
Thanks
Hi Saima,
With the Cisco 7942, you would leverage the setting under
the product specific porting of the config via device>phone
and set Wireless Headset Hookswitch Control to Enabled
http://headsetplus.com/PDF/Jabra-EHS-guide.pdf
Cheers!
Rob
"And if I should fall behind
Wait for me" - Springsteen
Similar Messages
-
Is it possible to use Cisco 1721 AUX port to dial into MS-RAS?
Is it possible to use Cisco 1721 AUX port with external modem to dial into Microsoft W2k-RAS server?
Hello Thanks for the link. The place where I'm stuck is when the async is going through the LCP negotiation. the LCP Confreg sends but I dont' get back anything. Cisco documentation states "make sure autoselect PPP or Async mode dedicated are set but I'm actually dialing into a Microsoft RAS server. Do you know where these settings are?
*Mar 1 05:38:04.782: As65 PPP: Phase is ESTABLISHING, Active Open
*Mar 1 05:38:04.782: As65 PPP: No remote authentication for call-out
*Mar 1 05:38:04.782: As65 LCP: O CONFREQ [Closed] id 43 len 20
*Mar 1 05:38:04.782: As65 LCP: ACCM 0x000A0000 (0x0206000A0000)
*Mar 1 05:38:04.782: As65 LCP: MagicNumber 0x314EFEBB (0x0506314EFEBB)
*Mar 1 05:38:04.786: As65 LCP: PFC (0x0702)
*Mar 1 05:38:04.786: As65 LCP: ACFC (0x0802)
*Mar 1 05:38:06.782: As65 LCP: TIMEout: State REQsent
*Mar 1 05:38:06.782: As65 LCP: O CONFREQ [REQsent] id 44 len 20
*Mar 1 05:38:06.782: As65 LCP: ACCM 0x000A0000 (0x0206000A0000)
*Mar 1 05:38:06.782: As65 LCP: MagicNumber 0x314EFEBB (0x0506314EFEBB)
*Mar 1 05:38:06.782: As65 LCP: PFC (0x0702)
*Mar 1 05:38:06.782: As65 LCP: ACFC (0x0802)
*Mar 1 05:38:08.782: As65 LCP: TIMEout: State REQsent
*Mar 1 05:38:08.782: As65 LCP: O CONFREQ [REQsent] id 45 len 20
*Mar 1 05:38:08.782: As65 LCP: ACCM 0x000A0000 (0x0206000A0000)
*Mar 1 05:38:08.782: As65 LCP: MagicNumber 0x314EFEBB (0x0506314EFEBB)
*Mar 1 05:38:08.782: As65 LCP: PFC (0x0702)
*Mar 1 05:38:08.782: As65 LCP: ACFC (0x0802) -
Jabra headset and Cisco 7942 Aux port
Hi ,
Two of our employees are using Jabra headsets. They are currently working over the analog headset port, but they would like to use the digital converter cable the headset came with to improve performance. How should I turned it on to utilize the auxiliary port in behind the phone.
Head model: Jabra GN9300e
Phone model: 7942
Any help would be much appreciated.
SaimaHi Saima,
With the Cisco 7942, you would leverage the setting under
the product specific porting of the config via device>phone
and set Wireless Headset Hookswitch Control to Enabled
http://headsetplus.com/PDF/Jabra-EHS-guide.pdf
Cheers!
Rob
"And if I should fall behind
Wait for me" - Springsteen -
Telnet to router through AUX port
i have configured my router to telnet through modem dialin but when i dials from my pc to router it give me garbage charcter in my hyperterminal. can any one help me that is this is problem with my router configuration or the cable connection with the router.
router AUX port --> ciscoconsole cable --> cisco 29-4043-01-->modemEven though the AUX port is supposed to "auto-baud" (usually you need to hit the "Enter" key a couple times), some/many/most/all current modems will set the DTE speed (the console cable) to the DCE speed (the modem-to-modem link) ... and "auto-baud" doesn't always work.
Since the modems will (by default) connect at 56K (or the top speed), chances are that it will try to talk to your Cisco device at some baud above 9.6K, which it is probably expecting.
You can do one of a couple things:
Hard set the modems to a 9.6k DTE speed (and/or DCE speed, since you won't go faster then the slowest baud)
OR
Experiment on the router to hard set the DTE speed to the baud set on the modem's serial port (frequently 115 kilobaud).
Check it out and get back to us.
Good Luck
Scott -
Connection a RS232 device to the Aux port.
Dear,
I have a home lab wthe a 2600 access server (16 port octal).
From this 2600 router I want to connect to a Raritan 8 ports RPC.
This RPC (Remote power control) has a rs232 serial port (RJ45)
I tried a lot and still I do not get connected to the RPC, has anyone ever done this before.
When I use a rs232 serial cable from the RPC to my serial pc port, I get into the rpc directly when putty is opened.
pinout RPC
Pinout Aux (cisco)
Pinout rs-232 (db9)
1 DTR
1 RTS
1 DCD
2 GND
2 DTR
2 RX
3 RTS
3 TX
3 TX
4 TX
4 GND
4 DTR
5 RX
5 GND
5 GND
6 -
6 RX
6 DSR
7 GND
7 DSR
7 RTS
8 DCD
8 CTS
8 CTS
9 RI (ring indicator)
I created several cables without succes.
I connected RTS to CTS and DTR to DSR.
On aux port I used the following.
speed 9600 8n1
transport all
modem inout
(also tried with modem printer)
I'm missing something to get is working.
Any help?
Kind regards,
RemkoIf you attach this USB drive to your Mac can it be accessed now?
-
Hi,
I have a following configuration:
Router AUX port -> FW Console
If there is something problem in the FW I can log the FW from cisco aux but the problem is now that the aux port is sending character's to FW's console port and now if the FW is rebooting it will go bootloop because when the FW boot's there is situation where is something "press any key" and now cisco router sends characters and the FW boots again.
Router AUX port config is following:
line aux 0
no exec
transport input all
stopbits 1
Which aux-port config the Cisco won't send any character to FW's console.
br
JHi Jody,
Thanks for your reply.
Actually I have no logging console configured at router but I will configure this also to the FW..I forgot to configure this at FW :) -
Out-of-band dialin to AUX port
Hi
Setting up a modem to dial into on the AUX port has been a nightmare. I have the following configured on R1:
line aux 0
password cisco
login
modem inout
speed 115200
flowcontrol hardware
transport input all
modem auto configure type default
I then have to reverse telnet to the modem, this being necessary for a remote dialin to connect to the aux port. However, when I dialin from a remote pc using the normal Microsoft dial-up connection, I get a black window with a blinking prompt but I'm unable to type in window. If I enter a command in the window, I can see it being entered into the modem of the AUX port. If I click the button called DONE on this screen, it gets stuck on "verifying username and password". The reverse consol session then shoots out garbage characters and connection drops.
All I want is a simple out-of-band dialin to connect to a remote router. I have spent 2 valuable days on this and gone through all documentation. Is it my dial-up connection or the modem (the modem is a standard 56k V.92/V.90 with NO dip switches only software switches). The only AT command I've used is the at&f1s0=1 I simply cannot get hold of a USRobotics modem in this country. I have tried connecting at 9600 but that doesn't work.
Help please
Marcuslook here http://www.cisco.com/en/US/tech/tk801/tk36/tech_configuration_examples_list.html
-
I have a dial-up modem connected to my router's AUX port.
Using this setup, I need to get remote users to access our internal servers via dial-up.
The users aren't network admins, so they should not have exec access to the routers. They only need to be able to access the servers on our system, i.e. I need to route their Laptops's traffic via the aux port to the intended server.
Is there a way of configuring the router and modem to do this? Or do I need more equipment in order for this to work?
The router is a 2960 series and the modem is a US Robotics dial up modem.
Any help is greatly appreciated. Thanks!These configs are a bit old and crusty , but they should give you an idea on how to set up async routing on the AUX ports. As Paolo says , performance is not brilliant, but it will work ... The chat scripts would likely need to be modified to suit your particular modems -
#####DIALING SIDE############
username PRIROUTER password SAMEPASSWORDS
chat-script modem "" "atdt\T" TIMEOUT 60 CONNECT \c
chat-script rstusr "" "at&fs0=1e0&r2&d2&c1&b1&h1&m4&k1q0" "OK"
interface Async1
ip address 192.168.10.2 255.255.255.0
encapsulation ppp
async default routing
async mode interactive
dialer in-band
dialer string 5553731
dialer-group 1
ppp authentication chap
ip route 0.0.0.0 0.0.0.0 Async1
dialer-list 1 protocol ip permit
line aux 0
modem InOut
script reset rstusr
transport input all
flowcontrol hardware
script dialer modem
######RECEIVING SIDE##############
Username RouterA password cisco
interface Async1
ip address 192.168.10.1 255.255.255.0
encapsulation ppp
async default routing
async mode dedicated
dialer in-band
dialer-group 1
ppp authentication chap
ip route 0.0.0.0 0.0.0.0 async1
dialer-list 1 protocol ip permit
chat-script rstusr "" "at&fs0=1e0&r2&d2&c1&b1&h1&m4&k1q0" "OK"
line aux 0
modem InOut
script reset rstusr
transport input all
flowcontrol hardware -
Air tunes wont play on home stereo using mini to RCA cord to Aux port
iTunes see's the base station and connects to it in itunes on Windows laptop and ipod touch but when the mini stereo jack to RCA 2 end cord is plugged from my home stereo to the Airport express but when I choose to play my iTunes through the base station no sound comes out through the stereo
Isn't this exactly what it is designed to do???
yes I have "home sharing on as well"
I can play my ipod touch hooked up to the stereo using the same mini jack to RCA cable whjile on the Aux port of the stereo why not the base station??
any ideas how I can get this to actually work???Could be a firewall issue. Try disabling the firewall, reboot, and then see if it works. If so I have found that I need to uninstall iTunes, enable firewall, reboot, reinstall iTunes
CB -
How to disable AUX port in ASR 9010
Hi All,
How to disable the AUX port in ASR 9010. Inside "line aux" I can't configure anything except "login authentication" (which is used for aaa authentication).
Also after IOS XR 3.2 the configuration for AUX port has been removed
Platform used: ASR 9010
Version: IOS-XR 4.1.2
Best Regards
Saikat ChakrabortyHi Saikat,
AUX has the same authentication method as we have on the system. From this perspective, AUX is protected the same way as the Console port and only those who have an account can login via AUX (same way as via console). Any attempts to log on AUX will be logged:
Successful:
ksh[65902]: Successfully authenticated user 'XXX' for ksh access via 'aux' on '0/RSP0/CPU0'
Incorrect:
ksh[65902]: Failed authentication attempt by user 'YYY' for ksh access via 'aux' on '0/RSP0/CPU0
But if anyone has a physical access to the device, that would be even bigger threat compare to system protected AUX login.
BTW, tacacs authentication should work for AUX too. We’d need to define a template for it.
Example:
aaa authentication login tacacs_template group tacacs+ local
line template aux
login authentication tacacs_template
Regards,
/A -
The Cisco MDS 9000 Port Analyzer Adapter
Hi,
At my client place, we are having an issue with BackUp via TSM and a library.
We would like to analyse the traffic that pass in the Fiber Channel of our MDS-9513.
From what we saw, Wireshark, our soft to analyse network traffic is only using NIC card to analyse.
Is the only way to analyse the FC traffic to pass via "The Cisco MDS 9000 Port Analyzer Adapter" ?
If that is the only way, is there a way tor ent this equipment for the time necesery to analyse our trace ?
Thank you in advance for you help.
Christian CarrierThe Cisco Traffic Analyzer provides real-time analysis of SPAN traffic or analysis of captured traffic through a Web browser user interface. Traffic encapsulated by one or more Port Analyzer Adapters can be analyzed concurrently with a single PC and ntop, which is public domain software enhanced by Cisco for Fibre Channel traffic analysis. This Cisco Traffic Analyzer solution enables you to quickly determine the throughput for traffic between specific Fibre Channel sources and destinations, all traffic in a particular Virtual SAN (VSAN), or all network traffic. Round trip response times, SCSI I/Os per second, SCSI read vs. write traffic throughput and frame counts, SCSI session status and management task information are provided. Additional statistics are also available on Fibre Channel frame sizes and network management protocols.
For further information click this link.
http://www.cisco.com/en/US/products/hw/ps4159/ps4358/products_data_sheet09186a0080142d34.html#wp1002317 -
How to fix aux port on cdx-gt250mp car stereo.
everything else works, but aux port quit working. after clicking select button until AUX appears on screen, it then immediately says "FRONT IN" and then goes blank
Hello serenajohnson
Welcome to Sony Community.
Ensure that a straight type plug has been used.
After "FRONT IN" appears, start playing back the portable audio device.
Try connecting a different device to the AUX IN jack of the Car Stereo.
If the same issue persists with a different portable audio device, then the Car Stereo will require service.
Refer to the below link to locate the nearest authorized service centers.
https://eservice.sony.com
Regards,
Colby -
Perhaps someone can respond to my issue with not being able to get my iphone to work through my vehicle's Auxilary Jack.
I bought a Monster Cable kit for Ipods. It is used to plug into your ipod then into your vehicle's Aux. port. Well it works perfect on my regular Ipod.
However it does nothing when I try it with my Iphone.
Any suggestions?
Thank you,
Robbie
[email protected]I bought a Belkin cable
http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/wa/RSLID?nnmm=br owse&mco=EEBCC376&node=home/iphoneaccessories/cablesdocks
and have no problems. Maybe Monster doesn't work with the iPhone. -
Hi Everyone,
I bought an 3.5mm cable to connect my iPhone to the Aux port on my car's radio. The playback works but only seems to play from one speaker. Is there a setting on the iPhone that I'm missing or do I need to play around with the settings on my car stereo?
ThanksIt was a cable issue. The cable I had was mono not stereo. Got the correct cable and it's working fine
-
Cisco 3750x 24 port poe switch single port is faulty.
what i can do if my cisco 3750x 24 port poe switch single port is faulty ????
Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12187366/cisco-3750x-24-port-poe-switch-failure
Maybe you are looking for
-
JOB_OPEN JOB_SUBMIT JOB_CLOSE
Hello Experts, I have a requirement where I want to execute a portion of my code in the background inorder to reduce the performance issue. This can be done through JOB_OPEN JOB_SUBMIT JOB_CLOSE command which generates a new JOB in the background mo
-
Cost Line Item Posting - which field indicates Order Number
Hi, I need to know the specific Order Number (example: PM order) with has cost postings on a WBS element. I am using COVP / COEP field OBJNR to see the WBS Element (those starts with PR*), but I do not know which field is the Order Nmber contained in
-
User having trouble connecting to VPN using mobile broadband card
I've got a user with a laptop running Windows 7 who is trying to use an AT&T mobile broadband card to connect to a VPN using the Cisco IPSec VPN client. The card is the Sierra Wireless Momentum 4G. The VPN connection established fine, but no traffic
-
The parents G3 has suddenly come up with a "no-entry" sign when booting up !! Any ideas ?
-
Catalog disapearance in lightroom 2
I decided to do my catalog backups while in lightroom 2 when approximatel over 200 pictures in other catalogs disappeared. What can I do they were not in the recycle bin?