Cisco B22HP Fabric Extender F/W upgrade failure

Please see attachement to see what happened to the Cisco B22HP Fabric Extder after a F/W upgrade was attempted showing the failure.

Hi,
Did you try to unconfigure/reconfigure your FEX ?
Did you try to downgrade/upgrade again the switch ?
Regards

Similar Messages

  • Hi. Does anyone know how to extend the airport express and extreme with Cisco Router DPC3925. I have upgrade my wireless to 50Mbps. Thank you

    Hi,
    Can someone help.
    I have a Cisco router DPC3925 provided by the ISP and I cannot extend my wireless with Airport Express.
    Also I intend to extend it with Airport Extreme.
    Please help.
    Thank you.

    Sorry, but your post is not clear. The topic of this thread is how to extend an AirPort Express or AirPort Extreme with a Cisco router.
    This would mean that the main router was an AirPort device and the Cisco would be extending the existing network provided by the AirPort.
    Is that really what you want to do?
    If not, then it sounds like your Cisco ISP provided wireless router is your "main" router and you will be using the Time Capsule to extend the network.
    Please start another post to tell us exactly.......
    What device will be the main router providing your Internet connection and wireless network
    What device will extend the network
    What operating system that you have on your Mac or PC

  • Fabric Extender question to a dual-homed N5k

    According to latest release notes:
    http://www.cisco.com/en/US/customer/docs/switches/datacenter/nexus5000/sw/release/notes/Rel_4_2_1_N1_1/Nexus5000_Release_Notes_4_2_1_N1_1.html#wp144071
    "Support for a maximum of 12 Fabric Extenders dual-homed to a vPC Cisco Nexus 5000 Series switch pair and a maximum of 576 hosts connected to Fabric Extenders connected to Cisco Nexus 5000 Series switches"
    I have mixed mode so some of the FEX will only connect to one N5k despite the 2N5k will be vpc. Cisco calls this "Fabric extender straight-through topology". This is because I am running port-channel with VM on these particular FEX.
    http://www.cisco.com/en/US/prod/collateral/switches/ps9441/ps9670/C07-572829-00_Design_N5K_N2K_vPC_DG.pdf
    question is:
    1. Can I assume 2148 is included per release notes?
    2. Can I have more than 2 ports in the portchannels in straight-through mode?
    3. Release notes show 576 host which is (12 max times 48 ports). I assume I can have more logical host meaning vm host via the port channels, right...?
    Thx

    Any Nexus 5000 can have a total of 12 FEX's connected to it physically.  If you have 12 FEX's in dual-homed mode, then that is the limit for both Nexus 5000's.  If you had 24 FEX's evenly distributed between the Nexus 5000's in straight-through mode, then that would be maximum in that configuration.  If you are mixing straight-through and dual-homed configurations, you would have to be within the 12 FEX per Nexus 5000 limit.
    The 2148 is the first FEX, so yes it is the focus of the release notes.
    The 2148 cannot have a local port-channel.  This is why you can only channel to a 2148 when using dual-homed (called Active-Active mode), one interface on each 2148, and it is tied together with a vPC configuration to make a port-channel.  The individual 2148's each only have one connection on them down to the server below.  The 2248 and 2232 do not have this restriction.
    As of 4.2(1)N1(1), 576 refers to host interfaces.  If your host has virtual hosts, you just need to make sure you are within the limit of mac addresses in the system, which is 16,000 (13,800 unicast).
    Regards,
    John Gill
    Reference:
    configuration limits -
    http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/configuration_limits/limits_421/config_limits_4_2_1_chapter1.html

  • Fabric Extender and Blade server connectivity(Cabling)

    Hi,
    There is lot of information available about how a Fabric extender connects to the Fabric interconnect. e.g. SFP+ ports, cabling etc.
    I am bit a confused, how does connectivity happen between the blade server and fabric extender inside the chassis.
    The information available only gives us idea about the possible network cards in the blade servers.
    I want to understand, how actual connectivity is done between the blade servers and fabric extenders.
    Is it through some cables or anything else? Please help.
    Thanks,
    Sushant

    Hi Sushant
    This has been discussed before
    https://supportforums.cisco.com/discussion/12130401/vnic-bandwidth-question
    https://supportforums.cisco.com/discussion/12207581/m81kr-vic-1240-and-vic-1280
    https://supportforums.cisco.com/discussion/11897266/vic1240-and-2208xp
    https://supportforums.cisco.com/discussion/11500981/vic-1280-vs-vic-1240-port-expander
    https://supportforums.cisco.com/discussion/11900386/10g-between-adpater-and-blades-vic12401280
    https://supportforums.cisco.com/discussion/12321671/ucs-enabledisable-dce
    Cheers
    Walter.

  • Can i use a cisco RE1000 range extender with airport extreme

    Can I use a Cisco R1000 range extender with airport extreme?

    Apple's "extend a wireless network" function appears to be a proprietary feature that will only work with other Apple routers.
    As far as we know, devices from other manufacturers are not compatible with this feature.
    Bottom line....It would be extremely unlikely that this would work, but it's worth a try if you already have the products in hand.
    Please post on your results.

  • Install order, PS CS5 extended and LR3 upgrades...

    I just purchased PS CS5 extended (upgrade from cs3 extended) and LR3 (upgrade from LR1). Which product should I install 1st, or does it matter?
    Thanks for any suggestions.
    Dan

    Install 3.2 first, remove CS3, then install CS5. This should make sure that the correct app path is in the registry so 3.2 can find the path to CS5.
    The reason people are having to reinstall CS5 is because when they install it, before removing the older version, the uninstaller for the older version removes the app path from the registry. One then must either reinstall CS5 or manually add the app path to the registry.
    Doing it in the order I gave you should avoid having to jump through a bunch of hoops.
    Rich
    Edited to add KB article.

  • Cisco MDS9124 Fabric Switch

    Hi
    We want to know if we can use a DS-IBM-FC-K9 part within this Cisco MDS9124 Fabric Switch ?
    Nomi

    Hello Nomi,
    Since there has been no reply to this post, it is being moved to the data center community for better visibility.
    Thank you,
    Fabienne.

  • Upgrading photoshop cs5 extended to cs7 upgrade older version

    upgrading photoshop cs5 extended to cs7 upgrade older version

    NO. I want to upgrade to CS7, as that is the version I already own, and 
    want to install it on my computer, which already has cs5. When I try, the cs7 
    software says it cannot find photoshop software on the computer, although I
    use  it all the time.
    Someone at Adobe help said my version of CS7, was too old to find the 
    version of CS5 on my computer and I should try the forum.
    In a message dated 9/24/2014 7:10:40 P.M. Eastern Daylight Time, 
    [email protected] writes:
    upgrading  photoshop cs5 extended to cs7 upgrade older version
    created by Jeff A Wright (https://forums.adobe.com/people/JeffAWright) 
    in Downloading, Installing, Setting Up - View the full  discussion
    (https://forums.adobe.com/message/6761437#6761437)

  • Problem extending VO after upgrade to JDev RUP6

    We are having problems extending VO after upgrading from JDev CU2 to JDev CU6. The extended VORowImpl java file extends the OAViewRowImpl instead of the VO that we are extending. Other files are fine except for the VORowImpl
    Is there any JDev setting we need to set for CU6?
    Any help/insight is appreciated.
    Thanks,
    Ramesh

    Hi,
    R u mean to say ur extended VO's changed automatically,or ur having problem extending the new VO's.
    Thanks

  • Cisco 3750G Integrated WLC upgrade failure

    I am trying to upgrade our Cisco 3750G Integrated WLC from version 5 to version 7, at 92% I receive an error
    Code file transfer failed - Error while writing output file
    There is enough space on WLC,
    Total System Memory............: 529088512 bytes
    Used System Memory.............: 121180160 bytes
    Free System Memory.............: 407908352 bytes
    I have tried 2 different TFTP servers..
    Any thoughts?

    Hi,
    1. Is it OK to upgrade to SWLC3750K9-5-2-193-0.aes ? or do I need to go through 4.2 first ?
    ANS - Yes you have to upgrade to 4.2 first and then to 5.2, here is the doc..
    http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn52xgmr1.html#wp233853
    2. Will that code upgrade the bootloader at the same time?
    ANS - Yes, after upgrading the WLC code upgrade the boot loader.. the boot loader is 5.2.157 (BOOT)
    3. How can I make sure there is enough flash space on the WLC?
    ANS - Dont worry.. we have enough flash!!
    4. Are there any special considerations to plan/prepare for?
    ANS - Yes, please upgrade the WLC in a planned , scheduled maitenance window.
    The DHCP issue is failure of associated clients to get an IP address with this message found in WLC debugging:
    Wed  Jul 20 17:16:37 2011: 00:19:db:5b:38:73 dhcpProxy: Dropping packet (no  mscb) from STA 00:19:db:5b:38:73, giaddr:0.0.0.0, udpSrcPort:68, op:1
    ANS - Issue the command ans see if that helps!!
    WLC CLI access...
    config dhcp proxy disable
    Lemme know if this answered ur question and please dont forget to rate the usefull posts!!
    Regards
    Surendra

  • Cisco 1200 series upgrade failure

    I have a Cisco 1200 Series (AIR-AP1231G-A-K9) access point, I have been upgrading these models to lightweight mode but are having issues with one in particular, this access point keeps "rebooting" itself, I am assuming that the upgrade faild, how can I get the access point upgraded?
    Here is a capture.
    Cisco IOS Software, C1200 Software (C1200-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by Cisco Systems, Inc.
    Compiled Mon 17-Jul-06 11:41 by alnguyen
    Image text-base: 0x00003000, data-base: 0x00359FC0
    Initializing flashfs...
    flashfs[1]: 4 files, 2 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 7741440
    flashfs[1]: Bytes used: 1862656
    flashfs[1]: Bytes available: 5878784
    flashfs[1]: flashfs fsck took 2 seconds.
    flashfs[1]: Initialization complete....done Initializing flashfs.
    cisco AIR-AP1231G-A-K9 (PowerPC405GP) processor (revision B0) with 15038K/1336K bytes of memory.
    Processor board ID FTX0914J0Z1
    PowerPC405GP CPU at 196Mhz, revision number 0x0145
    Last reset from reload
    LWAPP image version 3.0.51.0
    1 FastEthernet interface
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 00:13:7F:E2:34:DB
    Part Number : 73-8704-08
    PCA Assembly Number : 800-23211-09
    PCA Revision Number : A0
    PCB Serial Number : FOC09100NH1
    Top Assembly Part Number : 800-23304-08
    Top Assembly Serial Number : FTX0914J0Z1
    Top Revision Number : A0
    Product/Model Number : AIR-AP1231G-A-K9
    Press RETURN to get started!
    *Mar 1 00:00:04.505: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1200 Software (C1200-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by Cisco Systems, Inc.
    Compiled Mon 17-Jul-06 11:41 by alnguyen
    *Mar 1 00:00:05.442: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
    *Mar 1 00:00:06.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
    ap>
    ap>
    *Mar 1 00:00:14.441: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
    *Mar 1 00:00:23.516: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
    *Mar 1 00:00:23.544: LWAPP_CLIENT_ERROR_DEBUG: lwapp_crypto_init_ssc_keys_and_certs no certs in the SSC Private File
    *Mar 1 00:00:23.544: LWAPP_CLIENT_ERROR_DEBUG:
    *Mar 1 00:00:23.544: lwapp_crypto_init: PKI_StartSession failed
    *Mar 1 00:00:23.698: %SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: FAILED CRYPTO INIT.
    *Mar 1 00:00:23.698: %LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.
    flashfs[0]: 4 files, 2 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 7741440
    flashfs[0]: Bytes used: 1862656
    flashfs[0]: Bytes available: 5878784
    flashfs[0]: flashfs fsck took 9 seconds.
    Reading cookie from flash parameter block...done.
    Base ethernet MAC Address: 00:13:7f:e2:34:db
    Initializing ethernet port 0...
    Reset ethernet port 0...
    Reset done!
    ethernet link up, 100 mbps, full-duplex
    Ethernet port 0 initialized: link is up
    Loading "flash:/c1200-rcvk9w8-mx/c1200-rcvk9w8-mx"...#########################################################################################################################################################################
    File "flash:/c1200-rcvk9w8-mx/c1200-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
    executing...
    Restricted Rights Legend

    I might have an answer for you... or I might be COMPLETELY WRONG
    If it isn't just a "failed" upgrade, as in you've tried the upgrade again and it still is happening.... I was reading something about older APs not have a Manufacturing-installed certificate (MIC) and these AP's generating a Self-signed Certificate (SSC).
    The error you have is referring to SSC so I'm writing this as if you have not had to previously do this step for your other conversions.
    I believe a couple of things needs to happen for SSC AP's.
    1) Must enable controller to accept self-signed certificated.
    Security > AAA > AP Polices > Accept Self Signed Certificate > Apply
    2) Add AP to Authorization List in Security > AAA > AP Polices > Add AP To Authrorization List
    Enter MAC Address of the AP
    Certificate type = SSC
    SHA1 Key Hash can be obtained from the controller by issueing this command:
    "debug pm pki enable"
    Look for the line: sshpmGetIssuerHandles: SSC Key Hash is XXXXXXXXXXXXXXXXXXXXXXXXXX
    I believe you use the XXXXXXXXXXXXXXXXXXXXX as the SHA1 Key Hash.
    3) If required, you may also need to add the AP MAC Address in the Mac-Filter: Security > AAA > MAC Filtering > New >
    Hopefully its either a reload of the software or this SSC thing that fixes the problem....

  • Ism-cue upgrade failure

    Hi Pro,
    When I tried to upgrade from 8.5.1 to 8.6.1, I got the following failure. Has anybody come across this?
    The documentation only shows download the file with .pkg extension. What other files in the Unity Express Complete Installation File Set do I need to install?
    Would you like to continue?[confirm]
    Downloading ftp cue-vm-k9.SPA.sme.8.6.1.pkg
    Bytes downloaded :  687017
    Validating package signature ... done
    Validating installed manifests ............complete.
    - Parsing package manifest files... complete.
    - Checking Package dependencies... complete.
    Downloading ftp cue-vm-langpack.sme.8.6.1.pkg
    Bytes downloaded :  3986036
    Validating package signature ... done
    - Parsing package manifest files... complete.
    - Checking Package dependencies... complete.
    - Checking Manifest dependencies for subsystems in the install candidate list...
    - Checking Manifest dependencies for subsystems already installed...
    Error: Required Subsystem ID e2497725-368d-48b5-a7d5-7f87d889a608 was not found either on Installed or Candidate list.
    Thanks in advance.

    Hi take a look at this:
    Symptom: Software upgrade of CUE fails with the following error message: Error: Required Subsystem ID e2497725-368d-48b5-a7d5-7f87d889a608 was not found either on Installed or Candidate list.
    Conditions:
    1) CUE was shipped from Cisco with version 7.0.1 or later.
    2) One of the following upgrades is done:
    •7.0.x -> 7.1.x
    •7.1.x -> 8.0.x
    •7.0.x -> 8.0.x.
    Workaround: The workaround is to first remove a dummy subsystem using the following CLI command in exec mode, allow the system to reboot, and then do the upgrade: "software uninstall uid-list 26bd663c-3e5a-43d9-a6c3-5441ce44941b".
    Gabriel.

  • Cisco IPSEC VPN not working after upgrade to Mavericks

    I have been using the Cisco IPSEC VPN for almost 2 years with no issues. When I upgraded to Mavericks this week it stopped working. When i tell it to connect it prompts for password and attempts to connect for about 30 seconds then comes back with the following message...
    VPN Connection
    The negotiation with the VPN server failed. Verify the server address and try reconnecting.
    The address, group, shared secret, user and password are correct. Any help would be greatly appreiated.

    Hry, I'm not sure if this fixes the Cisco IPSec issue, but I can vouch for it fixing the L2TP issue that occurs after tha mavericks upgrade!
    I’ve got L2TP VPN working in Mavericks 10.9 and Server App 3.0.0 / 3.0.1.
    It really is quite a simple fix.
    Obviously, the standard caveats apply: This is a temporary, unsupported, workaround, and only a suggested idea at that. Again, this workaround is NOT supported by Apple.
    Proceed with this workaround on your own equipment at your own risk. And remember the golden rule: Always backup your data!
    OK so here goes… copy and paste the following into termini ONE LINE AT A TIME!
    cd /tmp
    curl -sO http://c5mart.co/mavericks-vpn-fix/racoon.tar.gz
    tar -xzvf racoon.tar.gz
    rm racoon.tar.gz
    sudo chown root:wheel racoon
    sudo chmod 555 racoon
    if [ ! -f /usr/sbin/racoon.mavericks ]; then sudo mv /usr/sbin/racoon /usr/sbin/racoon.mavericks; fi;
    sudo mv racoon /usr/sbin/racoon
    sudo killall racoon
    This works fine for me and I'm running a OSX Server for my entire office.
    …et voilà!

  • Calendar upgrade failure, how can I reset the new calendar

    Upgrading to the new v4 calendar on MobileMe has been a complete failure. Currently have a ticket open with Apple support, the upgrade failed with a "catastrophic failure message", my data was not fully transferred, etc.
    I need to reset the new calendar, clear it completely, then reimport data from my v3 calendar from a backup to see if it will work. Any clues? There appears to be zero data on this.
    Apple you really dropped the ball on quality control on this....

    Launch Photos again, but hold down the alt/options key ⌥ while double clicking the Photos icon to launch the app. This will bring up the library chooser panel. select the library that you want to migrate to Photos.
    After Photos completed the conversion, open the Preferences and select the new library as the main system library on the General tab of the Preferences.
    Then you can delete the other migrated Photos library.

  • Nexus 7010 fabric extender timing out

    Hello -
    We have a Nexus 7010 and we are testing out using the fabric extenders for a need.  We have a demo 2224 unit and have it connected to our M132XP-12 10G blade in the 7K but the FEX won't come online.  I would have figured a possible software incompatability but looking at the supported list for that as well as hardware everything seems to be in order.  This is what the status shows after it spends about 15 mins in the image download state.
    FEX: 111 Description: FEX0111   state: Offline
      FEX version: 4.2(1)N2(1a) [Switch version: 5.1(2)]
      FEX Interim version: 4.2(1)N2(1a)
      Switch Interim version: 5.1(2)
      Module Sw Gen: 21  [Switch Sw Gen: 21]
    pinning-mode: static    Max-links: 1
      Fabric port for control traffic: Eth2/20
      Fabric interface state:
        Po11 - Interface Up. State: Active
        Eth2/20 - Interface Up. State: Active
      Fex Port        State  Fabric Port  Primary Fabric
    This is looped in the log details until it times out:
    04/25/2011 15:31:41.986978: Module register received
    04/25/2011 15:31:41.987713: Registration response sent
    04/25/2011 15:31:41.987889: Requesting satellite to download image
    04/25/2011 15:32:00.105031: Module register received
    04/25/2011 15:32:00.105779: Registration response sent
    04/25/2011 15:32:00.105956: Requesting satellite to download image
    04/25/2011 15:32:20.191181: Module register received
    04/25/2011 15:32:20.191957: Registration response sent
    04/25/2011 15:32:20.192144: Requesting satellite to download image
    We ran a debug during this and these entries are displayed when looking for errors.
    2011 Apr 25 15:30:31.443745 fex: Reg resp: Failed to get card info for swcardid 132
    2011 Apr 25 15:30:35.472721 fex: Cardinfo: Unknown card id to get (132)
    2011 Apr 25 15:30:35.472753 fex: Reg resp: Failed to get card info for swcardid 132
    2011 Apr 25 15:30:41.495302 fex: Cardinfo: Unknown card id to get (132)
    I'm still doing some more searching which so far hasn't turned up much, wanted to see if anyone has some other insight??
    Thanks!

    Hi Jack -
    Thanks for the response.  Unfortunately, yes that is already complete.  I was hoping that would be an easy fix.  When we upgraded to 5.1(2) we did the 5.1 EPLD.  I ran the install all impact command noted below for the 5.1 EPLD just to make sure it didn't report anything else as needing upgrade.
    sho install all impact epld bootflash:n7000-s1-epld.5.1.1.img
    Compatibility check:
    Module  Type  Upgradable        Impact   Reason
         1    LC         Yes    disruptive   Module Upgradable
         2    LC         Yes    disruptive   Module Upgradable
         5   SUP         Yes    disruptive   Module Upgradable
         1  Xbar         Yes    disruptive   Module Upgradable
         2  Xbar         Yes    disruptive   Module Upgradable
         3  Xbar         Yes    disruptive   Module Upgradable
         1   FAN         Yes    disruptive   Module Upgradable
         2   FAN         Yes    disruptive   Module Upgradable
         3   FAN         Yes    disruptive   Module Upgradable
         4   FAN         Yes    disruptive   Module Upgradable
    Copy complete, now saving to disk (please wait)...
    Retrieving EPLD versions... Please wait.
    Images will be upgraded according to following table:
    Module  Type           EPLD      Running-Version   New-Version  Upg-Required
         1    LC  Power Manager              4.008       4.008           No
         1    LC  IO                         1.006       1.006           No
         1    LC  Forwarding Engine          1.006       1.006           No
         1    LC  SFP                        1.004       1.004           No
         2    LC  Power Manager              4.008       4.008           No
         2    LC  IO                         1.016       1.016           No
         2    LC  Forwarding Engine          1.006       1.006           No
         2    LC  FE Bridge(1)              186.006      186.006           No
         2    LC  FE Bridge(2)              186.006      186.006           No
         2    LC  Linksec Engine(1)          2.006       2.006           No
         2    LC  Linksec Engine(2)          2.006       2.006           No
         2    LC  Linksec Engine(3)          2.006       2.006           No
         2    LC  Linksec Engine(4)          2.006       2.006           No
         2    LC  Linksec Engine(5)          2.006       2.006           No
         2    LC  Linksec Engine(6)          2.006       2.006           No
         2    LC  Linksec Engine(7)          2.006       2.006           No
         2    LC  Linksec Engine(8)          2.006       2.006           No
         5   SUP  Power Manager              3.009       3.009           No
         5   SUP  IO                         3.028       3.028           No
         5   SUP  Inband                     1.008       1.008           No
         5   SUP  Local Bus CPLD             3.000       3.000           No
         5   SUP  CMP CPLD                   6.000       6.000           No
         1  Xbar  Power Manager              2.010       2.010           No
         2  Xbar  Power Manager              2.010       2.010           No
         3  Xbar  Power Manager              2.010       2.010           No
         1   FAN  Fan Controller (1)         0.007       0.007           No
         1   FAN  Fan Controller (2)         0.007       0.007           No
         2   FAN  Fan Controller (1)         0.007       0.007           No
         2   FAN  Fan Controller (2)         0.007       0.007           No
         3   FAN  Fan Controller (1)         0.007       0.007           No
         3   FAN  Fan Controller (2)        0.007       0.007           No
         4   FAN  Fan Controller (1)         0.007       0.007           No
         4   FAN  Fan Controller (2)         0.007       0.007           No

Maybe you are looking for

  • How do I access my files saved in the cloud

    Once I filled/edited files on acrobat, I am unable to print or save, but it shows that it's automatically saved in the Cloud.  How do I access my files saved in the Cloud and how can I print the edited files?

  • Column Headers of Masterdata Query

    Hello experts, in a Masterdata Query based on an InfoObject there are many Attributes. These Attributes are now listed in the Rows of the Query: InfoObject Attribut 1 Attribut 2 Attribut 3 Therefore the Query will look like this: InfoObject        At

  • How to send HTML emails with embedded graphics?

    I've discovered Mail is great for sending HTML if you open it in Safari and select "Mail Contents of this Page" - - My problem is, I need to include the graphic elements as embedded images rather than hosted images. Is there any way to do this with M

  • Identifier "parent_node" must be declared

    db and dev 10g rel2, i am trying to build a tree with this code , but that error appears , and i do not know why , my code is : declare        cursor dept_cur is         select deptno , dname         from   dept;         cursor emp_cur is         sel

  • Tabular Form With Dates Is Driving Me Nuts!

    Hello, Still new to the world of APEX/HTML-DB, and I'm pulling my hair out with something right now. I have a tabular form that is updating a table. I'm pre-populating the date field with a default value of SYSDATE and it's 'Display as Text (Saves St