Cisco BE7k Configuration Guide

Hi All,
I need to do a fresh installation of Cisco BE7k.
Can someone provide withe the links or conugiration/design guide,which can be followed.
Thanks,
Syed

Howdy, the only answer to such a general question would be to point you to the collab 10.x SRND: http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/srnd/collab10/collab10.html
Do you have any specific questions related to the deployment?
Also CUCM 10.x install guides:
http://www.cisco.com/c/en/us/support/unified-communications/unified-communications-manager-callmanager/products-installation-guides-list.html
Also Unity 10 Install guides:
http://www.cisco.com/c/en/us/support/unified-communications/unity-connection/products-installation-guides-list.html

Similar Messages

Need Cisco ISE Configuration Guide

Dear Friends,
Please send me cisco ISE configuration guide ASAP.
Thanks & Regards,
Rahul Wankhade

Check the following link for Step by step configuration guide it cover all the deployment related to ISE
http://www.cisco.com/en/US/solutions/ns340/ns414/ns742/ns744/landing_DesignZone_TrustSec.html
************Do rate helpful posts**********************

Really bad example in Cisco Wireless LAN Controller FlexConnect Configuration Guide, Release 7.4

I was just reading up on FlexConnect, and found this seriouly flawed example config. How does something like this manage to get published?
Really!!!
http://www.cisco.com/en/US/partner/docs/wireless/controller/7.4/configuration/guides/flexconnect/config_flexconnect_chapter_01.html#ID358
Same subnet on three different interfaces.
Both DHCP scopes are the same.
There is no spanning tree when a switchport is in routed mode.
Wrong mask on vlan 101.
You don't need a helper if the switch is the dhcp server.
There is no dns in the DHCP scope.
Configuring the Switch at a Remote Site
Step 1
Attach the access point that will be enabled for FlexConnect to a trunk or access port on the switch.
Note
The sample configuration in this procedure shows the FlexConnect access point connected to a trunk port on the switch.
Step 2
See the sample configuration in this procedure to configure the switch to support the FlexConnect access point.In this sample configuration, the FlexConnect access point is connected to trunk interface FastEthernet 1/0/2 with native VLAN 100. The access point needs IP connectivity on the native VLAN. The remote site has local servers/resources on VLAN 101. A DHCP pool is created in the local switch for both VLANs in the switch. The first DHCP pool (NATIVE) is used by the FlexConnect access point, and the second DHCP pool (LOCAL-SWITCH) is used by the clients when they associate to a WLAN that is locally switched. The bolded text in the sample configuration shows these settings.
A sample local switch configuration is as follows:ip dhcp pool NATIVE
   network 209.165.200.224 255.255.255.224
   default-router 209.165.200.225
ip dhcp pool LOCAL-SWITCH
   network 209.165.200.224 255.255.255.224
   default-router 209.165.200.225
interface FastEthernet1/0/1
description Uplink port
no switchport
ip address 209.165.200.228 255.255.255.224
spanning-tree portfast
interface FastEthernet1/0/2
description the Access Point port
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport trunk allowed vlan 100,101
switchport mode trunk
spanning-tree portfast
interface Vlan100
ip address 209.165.200.225 255.255.255.224
ip helper-address 209.165.200.225
interface Vlan101
ip address 209.165.200.226 255.255.255.225
ip helper-address 209.165.200.226
end

Hi Gary,
Is the following config correct?
ip dhcp pool NATIVE
   network 209.165.200.250 255.255.255.224
   default-router 209.165.200.225
dns-server 192.168.100.167
ip dhcp pool LOCAL-SWITCH
   network 209.165.201.20 255.255.255.224
   default-router 209.165.201.1
dns-server 192.168.100.167
interface FastEthernet1/0/1
description Uplink port
no switchport
ip address 209.165.201.25 255.255.255.224
interface FastEthernet1/0/2
description the Access Point port
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport trunk allowed vlan 101
switchport mode trunk
interface Vlan100
ip address 209.165.200.250 255.255.255.224
ip helper-address 209.165.202.128
interface Vlan101
ip address 209.165.201.20 255.255.255.224
ip helper-address 209.165.202.128
end
>

Cisco LMS 3.0 step by step configuration guide

Hi all,
Can any body give me cisco LMS 3.0 step by step configuration guide. that is great help for me.
Thanks
Afzal

LMS 3.0 is a very old version. You can refer to the product documentation here to start. The "Installing and Getting Started Guide" there should be useful.
You may want to take a look at this guide for LMS 4.1. Some of the terms are updated to reflect the application's changes over the past couple of years but the concepts are applicable.

What is BDI or BDS spelled out? Jabber for Mac 9.2(1) Installation and Configuration Guide

I’m spending the day catching up on Jabber/IM&P release notes across the server/clients.
So I’m used to EDI and UDS, but we have a new acronym in the Jabber for Mac 9.2(1) Installation and Configuration Guide called BDI and BDS. However they don’t define what BDI stands for other than BDI is LDAP for non-windows
Clients and suggests it should be used for Jabber for Mac.
What is BDI or BDS spelled out? Something directory integration, but what is the B ?
Then to add to the mix they reference BDS which sounds like the old UDS (is UDS changing to BDS?)
How can Jabber get any more confusing…
I also noted in the Jabber Video for iPad 9.3.4 release notes that Apple is removing the Always Connect option in the near future. Manually launching Cisco AnyConnect Secure Mobility Client before making a call. This is going to upset some customers who like how Lync uses https and just works from anywhere with enhanced directory integration…

Basic Directory Integration. It's not new, we had it in the Windows clients as far back as CUPC. The distinction got introduced when EDI was introduced, relying on Windows ADSI APIs instead of the client making a native LDAP bind.
To my knowledge BDI/BDS are the same thing; I'm guessing S is 'service'. UDS remains unchanged.
I also noted in the Jabber Video for iPad 9.3.4 release notes that Apple is removing the Always Connect option in the near future.
Well, they lost a patent infringement lawsuit and chose to change the functionality instead of pay the troll. That's not Jabber's fault. Collaboration Edge will be the way to avoid this in the near future.
Please remember to rate helpful responses and identify helpful or correct answers.

Help me about CDE205 (under SE mode) - CLI configuration guide

I'm trying to looking for "CLI Configuration guide for Cisco CDE205", but only GUI guide and command reference from cisco website.
Help me if you can.
Many thanks.

The name that you type into the portal login page is the "User Name Attribute". You currently have this set to "cn", which is "xxx" (not ascii). After this name is submitted to the portal, the "User Authentication Attribute" is sent to the AD AWS. Leaving this as userPrincipalName is correct. If you would like to change what users need to type into the portal, change the "User Name Attribute". The recommended value is "sAMAccountName". This should be "user1" in your example.

Cisco 5502 Configuration Example

I'm currently running a Cisco 5508 WLC. I currenlty want to use two Gigabit ports for Wireless traffic and I will only have 25 1142 Attached to this WLC. Reading the Cisco Wireless LAN Controller Configuration Guide, Release 6.0 it says :
5500 Series Controller Example
For a 5500 series controller, Cisco recommends having eight dynamic AP-manager interfaces and associating them to the controller's eight Gigabit ports. If you are using the management interface, which acts like an AP-manager interface by default, you need to create only 7 more dynamic AP-manager interfaces and associate them to the remaining seven Gigabit ports.
I was hoping to use LAG for these two ports and create a Port Channel on the switch for these ports. From Cisco's recommendation it sounds like I have to turn off LAG and create a dynamic interface for the second port and put that Port in a different VLAN. Can anyone please shed some light on this. Everything is working at the moment but I'm just curious why this recomendation. Any help would be greatly appreciated.

Lag works just fine. can you send me the link to the document you are looking at?

Configuration guide for ASA Ipsec.

Ho guys.
I need configuration guide for ASA Ipsec using Cli.
Thank you.
Sent from Cisco Technical Support iPad App

Hi,
please check the below link
http://www.cisco.com/en/US/products/ps9422/products_configuration_example09186a0080b4ae61.shtml?referring_site=smartnavRD
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00808c9950.shtml
Thanks and Regards,
ROHAN

Cisco 2504 Configuration

Hello,
I have a cisco 2504 controller with 10 AP's. I have 3 WLANs. I would like to have one WLAN only broadcast to 2 of my 10 AP's? Is this possible? If so how would I configure the WLan?

so i followed the configuration sheet that was listed in the article below
http://www.cisco.com/en/US/docs/wireless/controller/7.0MR1/configuration/guide/cg_wlan.html#wp1128591
Underneath the
Creating Access Point Groups
i followed it and made the modifications. But i am still able to see the one WLAN under all AP's?

Troubleshooting and Configuration Guide

HI, Can someone help me with the Troubleshooting and configuration guide for L3 VPN i.e--MPLS and L2 VPN i.e--ATM, FR
Regards
Raghav

Hi Raghav
Maybe you can tell us what exactly within MPLS VPNs you are trying to troubleshoot, if its basic troubleshooting, maybe this will help
http://www.cisco.com/warp/public/105/mpls_vpn_tsh.html
HTH
Maamun

Cisco IGESM Configuration

Guys,
Can the IBM BladeCenter chassis be used to connect the blade servers to different subnets (different physical segments also)?? The specific config that I have is using the Cisco IGESM switches.
Thanks guys.

Hello,
not sure if this is what you are asking, but I think you need an external router for that, that is, you can configure the ports IGESM ports for different VLANs, but in order to route between the VLANs, you need a routing device.
Check the ´Cisco Systems Intelligent Gigabit Ethernet Switch Modules Software Configuration Guide´ in the link below, and consult the chapter ´Configuring Interface Characteristics´ (Figure 7-1):
http://www.cisco.com/application/pdf/en/us/guest/products/ps6294/c1067/ccmigration_09186a00805b60d4.pdf
Regards,
GP

AP1602E - basic configuration guide ..

Hi
I bought a new 1602E ap .. so it comes with no documentation and the only doc that i foudn in the net it was this:
http://www.sws.cz/prod_img/cisco/ap1600getstart.pdf
but I need the started guide to the basic configuration ..
My concern is because the AP will be used for a producction enviroment and the point will be
what will be the best radio configuration with open with non security .. ? 2.4 or 5ghz ..
is any one know about it I appretitate your support
thnks in advanced
regards

Hi,
do you have AIR-CAP or AIR-SAP
as AIR-CAP is controller based AP where you need the WLC to get the AP configured. Simply you have to connect the AP with POE.
AIR-SAP is standalone and below is the doc to configure it:-
http://www.cisco.com/en/US/docs/wireless/access_point/15_2_4_JA/configuration/guide/scg15.2.4_book.html
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a0080c0b93c.shtml
2.4 GHZ or 5GHZ depends on what type of clients you want to connect ? If you have clients with A radio/ N radio then you need 5 GHZ and if your client is having G radio/N radio you can go for 2.4 GHZ.

LMS configuration guide

Hi Experts,
I need help on Cisco Prime LMS 4.1, I have installed it on the server and added some devices through add/import inventory but did not get any logs from devices.
I also configure snmp-server read and write community commands with snmp host commands,
Can i get any configuration guide or any link for related documents.
Expecting reply
Thanks
Fazal

After the addition Ciscoworks should automatically start managing the devices. The first thing it would do is to collect Inventory details to get it managed.
When you simply add a device using IP and login/snmp credentials via add/import, the device should appear unknown and once the basic inventory is done, ciscoworks should show device family icon (switch/router/FW/Voice etx), which should reflect LMS has started managing you device(s).
It seems "logs" is not clear on what is exactly you dont get.
Make sure the Credentials are correct which you can check via Credentials verification job, from:
Inventory > Job Browsers: Device Credential Verification
As Ciscoworks LMS is combinations of various modules segregated feature-wise like configuration, Fault Management, IP SLA etc. For more details please check the following End-User Guide Section :
http://www.cisco.com/en/US/products/ps11200/products_user_guide_list.html
-Thanks
Vinod

Cisco 1941W configure mac authentication in wireless

Dear all,
Appreciate that anyone know how to configure mac authentication in 1941w router?
Perhaps can show me some example of configure mac authentication in 1941w router.

Hi,
Below is the configuration for mac authentication bypass on cisco 1900 router
c1921> enable
c1921# configure terminal
c1921(conf)#interface gigabitethernet slot / port
c1921(conf-if)# authentication port-control auto
c1921(conf-if)# mab
c1921(conf-if)# end
> You can verify using the below command
c1921#show authentication sessions
Interface MAC Address Method Domain Status Session ID
Gi0/1 0201.0201.0201 mab DATA Authz Success 0303030300000004002500A8
c1921#show authentication sessions interface Gi0/1
Interface: GigabitEthernet0/1
MAC Address: 0201.0201.0201
IP Address: Unknown
User-Name: 02-01-02-01-02-01
Status: Authz Success
Domain: DATA
Oper host mode: single-host
Oper control dir: both
Authorized By: Authentication Server
Vlan Group: N/A
AAA Policies:
Session timeout: N/A
Idle timeout: N/A
Common Session ID: 0303030300000004002500A8
Acct Session ID: 0x00000007
Handle: 0x3D000005
Runnable methods list:
Method State
mab Authc Success
For more details refer the below link:
http://www.cisco.com/c/en/us/td/docs/routers/access/1900/software/configuration/guide/Software_Configuration/conf.pdf
Thanks & Regards
Sandeep

Process flow of letter of credit and configuration guide

Hi friends,
I want to know accounting entries at every stage in letter of credit for purchase transaction, so also requesting for configuration guide. Points will be assigned
my email id is [email protected]
Thanks
Edited by: keetu on Apr 22, 2008 8:35 AM

Hi,
Check these links.
http://forums.sdn.sap.com/thread.jspa?messageID=3537642#3537642
http://forums.sdn.sap.com/thread.jspa?messageID=5337739#5337739
Regards
Ayyallas

Cisco BE7k Configuration Guide

Similar Messages

Maybe you are looking for