Cisco Blade Switch

I am having problems with configuring speed on uplink ports on cisco blade switches (Cisco Gigabit Ethernet Switch Module for HP BladeSystem p-Class). I can configure fixed speed on uplink ports (Gi0/19-22) but after reload I am getting message that this command was rejected:
speed 1000
^
% Invalid input detected at '^' marker.
and then auto-1000 speed is specified.I need fixed speeds on those ports.What is strange that access ports (Gi0/1-18) dont have this problems.I excluded firmare problem,vlan,vtp negotation. The problem is still recouring even if I configure this ports only with speed comand and nothing more. Could someone give me some clues? Thanks

Checked that olso,ports are 10/100/1000/auto Base-TX with half/full/auto duplex, so it seems that it is not an issue. I am getting this problem after this communicate:
cisco 371098-001 (PowerPC405) processor (revision B0) with 118784K/12280K bytes
of memory.
Processor board ID FOC0948T07C
Last reset from power-on
1 Virtual Ethernet interface
24 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 00:15:FA:D2:1A:00
Motherboard assembly number : 73-9666-09
Motherboard serial number : FOC09480QLE
Model revision number : B0
Motherboard revision number : A0
Model number : 371098-001
Daughterboard assembly number : 73-9697-04
Daughterboard serial number : FOC09480SJU
System serial number : FOC0948T07C
Top Assembly Part Number : 800-25741-01
Top Assembly Revision Number : C0
Version ID : V01
Daughterboard revision number : A0
Hardware Board Revision Number : 0x02
Switch Ports Model W Version SW Image
* 1 24 371098-001 12.2(25)SED CGESM-LANBASEK9-M
speed 1000
^
% Invalid input detected at '^' marker.
speed 1000
^
% Invalid input detected at '^' marker.
speed 1000
^
% Invalid input detected at '^' marker.
speed 1000
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
Maybe there the answer lays. Do You know what is happeing then?

Similar Messages

  • Stacking with Cisco Blade Switches

    Hi,
    We have a HP p-class Blade System with two Cisco Gigabit Ethernet Switch Modules (Cisco IOS Release 12.2(25)SE) for every enclosure. My question is how I can stack the two blade switches (in the same enclosure) so that every HP blade server to be connected with the two switches in the active/standby state? In other words, can and how I make a port-channel which includes ports from the two switches?
    Unfortunately I couldn't found any documentation for the purpose.

    Hi,
    With the CGESM switches you have you cannot use 802.3ad teaming against the two blade switches. This is possible with the Cisco 3120 blade switches for HP c-class.
    Now, in your case, you can use standard Active/Standby NIC teaming, where the active NIC of each server connects to one switch and the standby NIC connects to the other switch. Should a blade switch completely fail, all of the servers with their active NIC connected to the failed switch should see the link go down and switch over to the standby NIC on the second switch. This should work very well.
    One problem that can happen however is that the blade switch itself does not completely fail. Instead maybe the blade switch uplink fails, or the upstream switch it is connected to fails. In this situation the server NIC does not experience a failure and continues to send traffic to the blade switch that does not have anywhere to send the traffic, a black hole. This is perhaps the problem you are seeing?
    The fortunate thing is that Cisco has a solution to this problem called Trunk Failover with Link State Tracking. What this allows you to do is to tell the blade switch that if it experiences a failure on its uplinks that it should also bring down the links to the servers as well. This will cause the servers to see a failure on their active NIC and perform a switchover to the second blade switch.
    I looked up your switch and found that your 12.2(25)SE1 code does not support this feature. You will need to upgrade to 12.2(25)SEE4 and you will be able to configure this on your switches.
    Here is a link to see how this configuration works:
    http://www.cisco.com/en/US/docs/switches/blades/3020/software/release/12.2_25_sef1/configuration/guide/swethchl.html#wp1346176
    Hope this helps.
    If so please rate my posts.
    Thanks,
    Brad

  • Cisco 3020 Blade Switch gecrashed

    Hi,
    One of our Blade switches has crashed, error log as follows,
    *Mar  1 05:31:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan550, changed state to up
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: System previously crashed with the following message:
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Cisco IOS Software, CBS30X0 Software (CBS30X0-LANBASE-M), Version 12.2(25)SEF1, RELEASE SOFTWARE (fc3)
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Copyright (c) 1986-2006 by Cisco Systems, Inc.
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Compiled Tue 23-May-06 15:26 by antonino
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: 
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Program Exception (0x0700)!
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: 
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: SRR0 = 0x003C38AC  SRR1 = 0x00029210  SRR2 = 0x00451BDC  SRR3 = 0x00021200
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: ESR = 0x08000000  DEAR = 0x00000000  TSR = 0x84000000  DBSR = 0x00000000
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: 
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: CPU Register Context:
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Vector = 0x00000700  PC = 0x003C38AC  MSR = 0x00029210  CR = 0x20000008
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: LR = 0x003C38A4  CTR = 0x0027C814  XER = 0x60000020
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: R0 = 0x003C38A4  R1 = 0x014D6650  R2 = 0x00000000  R3 = 0x00000004
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: R4 = 0x013A1E60  R5 = 0x00000001  R6 = 0x00433EDC  R7 = 0x00000004
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: R8 = 0x00029210  R9 = 0x00000002  R10 = 0x01220000  R11 = 0x00F60000
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: R12 = 0x0070D567  R13 = 0x00110000  R14 = 0x00000002  R15 = 0x00000000
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: R16 = 0x00000000  R17 = 0x00000000  R18 = 0x01220000  R19 = 0x01220000
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: R20 = 0x00F0CF5C  R21 = 0x012D27D0  R22 = 0x01220000  R23 = 0x0187F530
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: R24 = 0x00000000  R25 = 0x0004073F  R26 = 0x01220000  R27 = 0xEF180E50
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: R28 = 0xEF19007A  R29 = 0x00000000  R30 = 0x01220000  R31 = 0x00000000
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: 
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Stack trace:
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: PC = 0x003C38AC, SP = 0x014D6650
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Frame 00: SP = 0x014D6678    PC = 0x003C38A4
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Frame 01: SP = 0x014D6680    PC = 0x003C3964
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Frame 02: SP = 0x014D66A0    PC = 0x004B97AC
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Frame 03: SP = 0x0126264C    PC = 0x00451060
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Frame 04: SP = 0x0126265C    PC = 0x00451008
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Frame 05: SP = 0x0126267C    PC = 0x0045342C
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Frame 06: SP = 0x01262684    PC = 0x004538F8
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Frame 07: SP = 0x012626D0    PC = 0x00451110
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Frame 08: SP = 0x0187F298    PC = 0x0000D3CC
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Frame 09: SP = 0x0187F2A0    PC = 0x002659D8
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Frame 10: SP = 0x0187F4D0    PC = 0x00423870
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Frame 11: SP = 0x0187F4E8    PC = 0x00AAF21C
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Frame 12: SP = 0x0187F528    PC = 0x006C9400
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Frame 13: SP = 0x0187F5F8    PC = 0x006C8E04
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Frame 14: SP = 0x0187F610    PC = 0x006C8A64
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: Frame 15: SP = 0x0187F638    PC = 0x006C848C
    .Dec 26 22:21:20: %PLATFORM-1-CRASHED: 
    Dec 27 09:10:14: %SYS-5-CONFIG_I: Configured from console by vty0 (172.22.25.22)
    Please help to fixed this issue,
    Asa,

    Signal = 4, Vector = 0x700
    Thank you very much for the output.  They were very helpful.
    Here's the story, the blade has been crashing because of the error "Signal = 4".  I have never seen something like this so the only thing I can tell you is that this is a code that simply means "Illegal Opcode Exception".  It could mean that you are running an old IOS and you're hitting a bug.
    You can contact Cisco TAC and get them to analyze the crashinfo files.  You can put this thread into the TAC Case so you don't need to repeat your story all over again.

  • Cisco Catalyst Blade Switch 3020

    Information about the Cisco Catalyst Blade Switch 3020
    Does it support  TCP SYN Flooding Attacks Mitigations Techniques
    As per the Request for Comments: 4987 

    Most of the common DOS attack mitigation strategies (good overview here) are configurable on the CBS 3020. There's no "one step lockdown" like the autosecure feature on routers but the configuration guide covers all of the details on setting the individual mechanisms (DHCP Snooping, DAI, IP source guard, etc.) you may wish to employ.

  • "Cisco Catalyst Blade Switch 3020 for HP" Best Practices

    Hi all,
    Here we use this blade switch cluster for the Data Center server farm. Here we noticed some network traffic delay. when I monitor the up link I can see there is not much traffic in the link. So doubt about the traffic delay. If anyone can help me on this it would be great...
    Thanks in Progress.....
    Chandana

    Here in the "blade switch for HP" a request processing application is running in a server. when we use the same type server stand alone with a separate switch it processes 80,000 requests per 4 hours. But when this blade server in the blade switch it only processes near 6,000 requests per 4 hours.
    That what I mean like "Network delay"...
    That is what I cannot understand.
    I have attached the current configuration of the blade switch so you can go through it.
    Is there any best practices specific to that type of blade switch that should enable?
    Thanks for your help
    regards
    Chandana

  • Two forwarding root ports on cisco 3120 blade switch.

    Hi,
    <br />
    <br />After upgrading blade switch 3120 to 12.2(46)SE, I could see two root ports in which both are forwarding.
    <br />
    <br />Te1/0/1 Root FWD 2000 128.27 P2p
    <br />Te2/0/1 Root FWD 2000 128.81 P2p
    <br />
    <br />Where as STP should've kept the other root port as blocked state and named it has Alternate port.
    <br />Also started seeing Mac flap messages.
    <br />As soon as IOS was downgraded to 12.2(40)EX3, Problem was solved, even messages were stoped.
    <br />Seems to be bug, but couldn't get any.
    <br />

    Hi Rob,
    I have faced this issue with many enclosures so far and the only option left here is, you need to reboot the enclosure.
    This is an issue with the IOS code and you have to open a case with HP to get the appropriate IOS ver. Probably 15.0 code has this issue resolved and I haven't seen this issue further after the Upgrade.
    Thanks,
    Sagar

  • Blade Switch Management

    I am deploying HP BladeSystem C Class with Cisco 3020 Ethernet blade switches connecting to Catalyst 6500 at the aggregation layer. What are my best options for managing layer 2, VLANs, etc, across the Cat6K and 3020 switches?

    Matt,
    Great catch, thank you!
    Switch#show link state group detail
    Link State Group: 1 Status: Disabled, Up
    Upstream Interfaces : Po1(Up)
    Downstream Interfaces : Gi0/1(Up) Gi0/2(Up) Gi0/3(Up) Gi0/4(Up) Gi0/5(Up)
    Gi0/6(Up) Gi0/7(Up) Gi0/8(Up) Gi0/9(Up) Gi0/10(Up)
    Gi0/11(Up) Gi0/12(Up) Gi0/13(Dwn)
    Link State Group: 2 Status: Disabled, Down
    Upstream Interfaces :
    Downstream Interfaces :
    (Up):Interface up (Dwn):Interface Down (Dis):Interface disabled
    Switch#conf t
    Enter configuration commands, one per line. End with CNTL/Z.
    Switch(config)#link state trac
    Switch(config)#link state track 1 ?
    Switch(config)#link state track 1
    Switch(config)#end
    Switch#show link state group detail
    Link State Group: 1 Status: Enabled, Up
    Upstream Interfaces : Po1(Up)
    Downstream Interfaces : Gi0/1(Up) Gi0/2(Up) Gi0/3(Up) Gi0/4(Up) Gi0/5(Up)
    Gi0/6(Up) Gi0/7(Up) Gi0/8(Up) Gi0/9(Up) Gi0/10(Up)
    Gi0/11(Up) Gi0/12(Up) Gi0/13(Dwn)
    Link State Group: 2 Status: Disabled, Down
    Upstream Interfaces :
    Downstream Interfaces :
    (Up):Interface up (Dwn):Interface Down (Dis):Interface disabled
    Switch#
    Scott
    www.xpresslearn.com

  • MDS FC Blade Switch for IBM - Licensing

    Hi,
    our customer has got installed the 20-port-switch of the "Cisco MDS Fibre Channel Blade Switch for IBM BladeCenter". He wants to change some of the links now. For that reason he asked me:
    - Is there a fix relationship between a port and a license?
    - Can we use any port as long as we fall below the number of licenses?
    Thanks in advance and regards
    Matthias

    Hello Matthias,
    Cisco Fabric Switch for IBM BladeCenter (20 ports; 14 internal 2/4 Gbps, and 6 external full-rate ports) licenses for internal ports are allocated as the ports come up. Licenses for external ports are allocated sequentially.
    Refer "On-Demand Port Licensing" section on CLI guide here :
    http://www.cisco.com/en/US/docs/storage/san_switches/mds9000/sw/rel_3_x/configuration/guides/cli_3_3/ondport.html
    Customer can select the specific external ports he wants licensed.
    switch# config t
    switch(config)# interface fc1/1
    switch(config-if)#port-license acquire
    Thanks,
    Prateek

  • Etherchannel and STP on HP Blade Switches

    Hi Guys,
    I have a 6509 with and etherchannel connection to an HP Blade switch... the channel is made up of two phy ports between the two switches...
    When I try ti bring up the link, the 6509 ports go into err-disable and i get the message below.
    I have done all (I think?) checks that there is to ensure etherchannle compatibility and STP stuff but still no luck...
    can anyone suggest soemthing I do ro check that might shed light on this...
    thanks
    2005 Jun 26 02:53:06 AEDT +10:00 %ETHC-5-PORTTOSTP:Port 10/24 joined bridge port 10/24-25
    2005 Jun 26 02:53:06 AEDT +10:00 %SPANTREE-6-PORTLISTEN: Port 10/24-25 (agPort 14/45) state in VLAN 144 changed to listening
    2005 Jun 26 02:53:20 AEDT +10:00 %SPANTREE-6-PORTLEARN: Port 10/24-25 (agPort 14/45) state in VLAN 144 changed to learning
    2005 Jun 26 02:53:35 AEDT +10:00 %SPANTREE-6-PORTFWD: Port 10/24-25 (agPort 14/45) state in VLAN 144 changed to forwarding
    2005 Jun 26 02:54:23 AEDT +10:00 %SPANTREE-2-CHNMISCFG: STP loop - channel 10/24-25 is disabled in vlan/instance 144
    2005 Jun 26 02:54:23 AEDT +10:00 %SPANTREE-2-CHNMISCFG2: BPDU source mac addresses: 00-03-fe-af-d0-b5, 00-11-f9-21-56-00
    2005 Jun 26 02:54:23 AEDT +10:00 %ETHC-5-PORTFROMSTP:Port 10/24 left bridge port 10/24-25

    Hi ankur,
    thanks for your response. currently the etherchannel operatiosn mode on the 6509 is set to manual, which is the case globally for the 6509 and we have 50 pairs of this blade switch running on this 6509... I don't think that that is the cuase of this issue since this is the only one not forming the channel and goes into err-disable...
    the blades also have similar configs in them...
    the only thing I see different on ports 10/24-25 is that it has bpdu-guard set to disable while the rest are set to default... could this make a diffrence?
    also, does the order of enabling the cisco end and the HP blade end make a difference? i.e. should I bring up one first than the other?
    the thing is I cannot "experiment" fully as this is a full prod network...
    Any input si appreciated...

  • Catalyst Blade Switches 3020 For HP Blade Chassis

    I was trying to access Catalyst Blade Switch 3020 through serial port to reset the lost password. This Switch is plug-in to HP c7000 Chassis. I followed the instruction from Cisco documentation for this password re-set process as follows.
    { Step 1 Connect a terminal or PC with terminal-emulation software to the switch console port.
    Step 2 Set the line speed on the emulation software to 9600 baud.
    Step 3 Push the release latch on the front of the switch to the open position.
    Step 4 Pull the switch partially out of the module bay until the power disconnects, and then push it in again. The switch restarts when it reseats in the server chassis. The switch performs POST after power is applied.
    Step 5 Push the release latch on the front of the switch to the closed position.
    Step 6 Within 15 seconds, press the Mode button while the System LED is still flashing green. Continue pressing the Mode button until the System LED turns briefly amber and then solid green; then release the Mode button.
    ------- Step 6 did not work. System LED neither flashing nor in Solid state. I can not connect through Serial port any more! Any help.....

    Here in the "blade switch for HP" a request processing application is running in a server. when we use the same type server stand alone with a separate switch it processes 80,000 requests per 4 hours. But when this blade server in the blade switch it only processes near 6,000 requests per 4 hours.
    That what I mean like "Network delay"...
    That is what I cannot understand.
    I have attached the current configuration of the blade switch so you can go through it.
    Is there any best practices specific to that type of blade switch that should enable?
    Thanks for your help
    regards
    Chandana

  • Link-state protocol on blade switches

    Hi,
    Can anyone confirm is after an uplink is reestablished the down stream interfaces are automatically restored when using link-state protocol?
    The documentation states the downstream ports in a group are put in error disable state but doesn't say if they are automatcally made up when the upstream interface comes back up. This refers to Cisco blade 3020 switches running 12.2.25
    http://www.cisco.com/c/en/us/td/docs/switches/blades/3020/software/release/12-2_55_se/configuration/guide/3020_scg/swethchl.html#wp1346176
    Thanks
    Ken

    Link state tracking, also known as trunk failover, provides Layer 2 redundancy in the network when used in conjunction with server network interface card (NIC) adapter teaming. Link-state tracking is used to mirror the state of the ports that carry upstream traffic from connected hosts and servers, and to allow the failover of the server traffic to an operational link on another Cisco Ethernet switch. Check out the following link for more information on link state tracking :
    http://www.cisco.com/en/US/products/ps6406/products_configuration_guide_chapter09186a00805a75e0.html#wp1285238
    Hope this helps.

  • Nexus5k - LACP towards HP blades switch(and nortel blade switch)

    Hi
    First I have to say this is not the first time i'm working with these old switches and not the first time i've configured LACP on them.
    So I did the config on the blade switch , enabled LACP, the uplink ports as members and tagged.
    Created port-channel on the nexus side.
    when i try to bring up the ports on the Cisco Nexus 5k this is the errors I get. this is fot the HP blade:
    2013 Jun 11 14:44:03 dist4 %ETH_PORT_CHANNEL-5-PORT_SUSPENDED: Ethernet171/1/7: Ethernet171/1/7 is suspended
    2013 Jun 11 14:44:03 dist4 %LACP-FEX171-3-LACP_MEM_PC_MISCFG: LACP misconfiguration detected on Ethernet171/1/7(0x1faa0180): (Member channel group id: 31-1, does not match PC group id: 31-1
    0)
    2013 Jun 11 14:44:04 dist4 %ETH_PORT_CHANNEL-5-PORT_SUSPENDED: Ethernet172/1/7: Ethernet172/1/7 is suspended
    2013 Jun 11 14:44:04 dist4 %LACP-FEX172-3-LACP_MEM_PC_MISCFG: LACP misconfiguration detected on Ethernet172/1/7(0x1fab0180): (Member channel group id: 31-1, does not match PC group id: 31-1
    0)
    I had one port-channel for a switch that came up with no problems. I compared the config but could not identify the issue.the config is very similar.
    has anyone encountered these errors or similar before? if yes, what am I missing? and also what does it mean when it says "
    Member channel group id: 31-1, does not match PC group id: 31-10) ?
    Thanks,
    Mary

    Marcel,
    Thank you for your reply.
    I tried again right now with the command you suggested but still no luck.
    we have so many more hp switches with the similar config that are working fine. I just can't figure out why these 3 switches are having issues.
    my current config on the member port is as below
    interface Ethernet171/1/36
      description WINBL1-NFS2:P2
      lacp rate fast
      switchport mode trunk
      switchport trunk allowed vlan 410,412
      spanning-tree bpdufilter enable
      flowcontrol send off
      channel-group 30 mode active
    2013 Jun 13 11:00:51 dist4 %ETH_PORT_CHANNEL-5-PORT_SUSPENDED: Ethernet171/1/36: Ethernet171/1/36 is suspended
    2013 Jun 13 11:00:51 dist4 %LACP-FEX171-3-LACP_MISCFG: LACP misconfiguration detected on Ethernet171/1/36(0x1faa08c0): (Member system mac does not match PC system mac)
    2013 Jun 13 11:00:52 dist4 %ETH_PORT_CHANNEL-5-PORT_SUSPENDED: Ethernet172/1/36: Ethernet172/1/36 is suspended
    2013 Jun 13 11:00:50 dist4 %LACP-FEX172-3-LACP_MISCFG: LACP misconfiguration detected on Ethernet172/1/36(0x1fab08c0): (Member system mac does not match PC system mac)
    Thanks,
    Mary

  • Thanks to confirm AP521 NEED Cisco 520 Switch

    Thanks to confirm that AP521 need a Cisco 520 Switch. And that it cannot works without Cisco product.

    1. Yes...you configure the IP address via the IBM blade center Management Module web interface.
    2. Depending on the version of firmware on the swtich module, the FM may or may not be inluded.  The device manager client will be there and can be downloaded via the web connection. I believe that with 4.x and later code, FM is no longer included in the switch firmware.
    3. Yes the default user id is USERID and PASW0RD (zero not 0)  from this user you can add aditional user/passwords for management.
    4. Yes, you can upgrade via TFTP server or diretly via Fabric Manager, there is no mechanism for using Device Manager to upgreade code.
    5. Nothing special needs to be done.  By defauylt, the ports EXT0, EXT15, and EXT16 are licensed.  If you need additional external ports, you must license the additional 10 ports on the module.
    Hope this helps,
    Mike

  • WWN does not show up on Cisco SAN Switch

    We use Cisco SAN Switches MDS 9134 and MDS9222i with NX-IOS 4.2.(3). Our HP c7000 blade enclosure is connect through a Fibre Channel Virtual Connect Card to the SAN switches. For so far is everything working Oke. Now is the problem when I connect the 8th and 9th Blade Server (BL860c i2 Integrity Server) to the c7000 enclosure non of the wwn's show up on the Cisco Switch. Neither on the MDS9134 as the MDS9222i.Firmware on the HP Blade is up to date. The Onboard Administrator show that the HBA's are logged-in to Virtual Connect.
    Does anyone know solution for this issue.
    Best Regards,
    Robert

    Hi Robert,
    The output of "show flogi database" will show you all the wwn's of devices connected directly to a particular
    switch.
    Is NPV involved in your topology?
    Regards,
    Ken

  • Packet loss when pinging from/to a cisco 3560e switch

    I see Packet loss when pinging from/to a cisco 3560e switch. CPU utilization is normal.
    Switches are running with IOS c3560e-universalk9-mz.122-35.SE5.bin.
    Packet loss is observed for all the devices irrespective of directly connected or remote devices.
    If i do self pinging, there are no packet loss.
    I don't see any error on interface.
    Can anyone please help me in resolving this issue.

    TCB       Local Address           Foreign Address        (state)
    03737C48  10.47.0.229.60053       10.41.81.55.49         CLOSEWAIT
    039ACDC4  10.47.0.229.61929       10.41.35.250.49        CLOSEWAIT
    03B316C0  10.47.0.229.27544       10.41.81.55.49         CLOSEWAIT
    038228F0  10.47.0.229.16506       10.41.35.250.49        CLOSEWAIT
    039C3D04  10.47.0.229.15207       10.41.81.55.49         CLOSEWAIT
    039A9BD0  10.47.0.229.52983       10.41.81.55.49         CLOSEWAIT
    0394152C  10.47.0.229.22425       161.61.35.250.49       CLOSEWAIT
    037D811C  10.47.0.229.21117       10.41.81.55.49         CLOSEWAIT
    039C12BC  10.47.0.229.37437       10.41.81.55.49         CLOSEWAIT
    03933B84  10.47.0.229.34085       161.61.35.250.49       TIMEWAIT
    03B32340  10.47.0.229.45729       10.41.81.55.49         CLOSEWAIT
    038247D0  10.47.0.229.32816       10.41.81.55.49         CLOSEWAIT
    039A92D8  10.47.0.229.38680       161.61.35.250.49       CLOSEWAIT
    037370F0  10.47.0.229.13212       10.41.81.55.49         CLOSEWAIT
    037D85F0  10.47.0.229.38728       10.41.81.55.49         CLOSEWAIT
    03B2B284  10.47.0.229.23428       10.41.81.55.49         CLOSEWAIT
    03B2ADB0  10.47.0.229.56836       10.41.81.55.49         CLOSEWAIT
    0394BFF0  10.47.0.229.23257       161.61.35.250.49       CLOSEWAIT
    036604DC  10.47.0.229.44437       10.41.81.55.49         CLOSEWAIT
    0394C700  10.47.0.229.22          192.37.184.211.61639   ESTAB
    039B9A68  10.47.0.229.20543       10.41.81.55.49         CLOSEWAIT
    03739B28  10.47.0.229.15392       10.41.81.55.49         CLOSEWAIT
    TCB       Local Address           Foreign Address        (state)
    0392EA48  10.47.0.229.13862       10.41.81.55.49         CLOSEWAIT
    0365E23C  10.47.0.229.27856       10.41.81.55.49         CLOSEWAIT
    03817C0C  10.47.0.229.64929       10.41.81.55.49         CLOSEWAIT
    039357C8  10.47.0.229.22088       10.41.81.55.49         CLOSEWAIT
    037375C4  10.47.0.229.21832       10.41.81.55.49         CLOSEWAIT
    039C20E8  10.47.0.229.18169       10.41.81.55.49         CLOSEWAIT
    03716D08  10.47.0.229.61993       10.41.81.55.49         CLOSEWAIT
    039A74E4  10.47.0.229.62948       10.41.81.55.49         CLOSEWAIT
    03655480  10.47.0.229.14052       10.41.81.55.49         CLOSEWAIT
    039407F0  10.47.0.229.49643       161.61.35.250.49       CLOSEWAIT
    039A53AC  10.47.0.229.13233       10.41.81.55.49         CLOSEWAIT
    03739FFC  10.47.0.229.16605       10.41.81.55.49         CLOSEWAIT
    039B82B8  10.47.0.229.16458       10.41.35.250.49        CLOSEWAIT
    039BEBA4  10.47.0.229.64377       10.41.81.55.49         CLOSEWAIT
    03741980  10.47.0.229.13866       10.41.81.55.49         CLOSEWAIT
    03B3ABF8  10.47.0.229.19365       10.41.81.55.49         CLOSEWAIT
    039B5810  10.47.0.229.24768       10.41.81.55.49         CLOSEWAIT
    03956E48  10.47.0.229.55980       161.61.35.250.49       CLOSEWAIT
    03946820  10.47.0.229.65053       161.61.35.250.49       CLOSEWAIT
    037DBE94  10.47.0.229.15283       10.41.81.55.49         CLOSEWAIT
    039A4854  10.47.0.229.48562       10.41.81.55.49         CLOSEWAIT
    TCB       Local Address           Foreign Address        (state)
    03B33320  10.47.0.229.29803       10.41.81.55.49         CLOSEWAIT
    03B3B79C  10.47.0.229.12142       10.41.81.55.49         CLOSEWAIT
    03713C9C  10.47.0.229.63799       10.41.81.55.49         CLOSEWAIT
    039BBECC  10.47.0.229.14763       10.41.81.55.49         CLOSEWAIT
    03656E40  10.47.0.229.16357       10.41.81.55.49         CLOSEWAIT
    0362A73C  10.47.0.229.62450       10.41.81.55.49         CLOSEWAIT
    039B878C  10.47.0.229.64402       161.61.35.250.49       CLOSEWAIT
    03826CFC  10.47.0.229.16108       10.41.81.55.49         CLOSEWAIT
    03B2CA34  10.47.0.229.17634       10.41.81.55.49         CLOSEWAIT
    03AD78D0  10.47.0.229.15249       161.61.35.250.49       CLOSEWAIT
    03AD967C  10.47.0.229.20389       161.61.35.250.49       CLOSEWAIT
    03B2C560  10.47.0.229.37079       10.41.81.55.49         CLOSEWAIT
    039C5128  10.47.0.229.24711       10.41.81.55.49         CLOSEWAIT
    03822F74  10.47.0.229.54866       10.41.81.55.49         CLOSEWAIT
    0372C5FC  10.47.0.229.13298       10.41.81.55.49         CLOSEWAIT
    0372D278  10.47.0.229.12407       10.41.81.55.49         CLOSEWAIT
    039A33D0  10.47.0.229.36573       10.41.81.55.49         CLOSEWAIT
    039BCEF8  10.47.0.229.53853       10.41.81.55.49         CLOSEWAIT
    039C02D8  10.47.0.229.53725       10.41.81.55.49         CLOSEWAIT
    039B5CE4  10.47.0.229.58027       10.41.81.55.49         CLOSEWAIT
    0381866C  10.47.0.229.17100       10.41.81.55.49         CLOSEWAIT
    TCB       Local Address           Foreign Address        (state)
    039BB374  10.47.0.229.53148       10.41.81.55.49         CLOSEWAIT
    03AD3634  10.47.0.229.19716       161.61.35.250.49       CLOSEWAIT
    0362DAA4  10.47.0.229.19479       10.41.81.55.49         CLOSEWAIT
    0365AE60  10.47.0.229.62209       10.41.81.55.49         CLOSEWAIT
    0362D5D0  10.47.0.229.41327       10.41.81.55.49         CLOSEWAIT
    037D7C48  10.47.0.229.58283       10.41.81.55.49         CLOSEWAIT
    03955474  10.47.0.229.33810       161.61.35.250.49       CLOSEWAIT
    0373B15C  10.47.0.229.23331       10.41.81.55.49         CLOSEWAIT
    036628D0  10.47.0.229.46856       10.41.81.55.49         CLOSEWAIT
    03819584  10.47.0.229.19861       10.41.81.55.49         CLOSEWAIT
    0394D000  10.47.0.229.64732       10.41.35.250.49        CLOSEWAIT
    0394B760  10.47.0.229.19967       161.61.35.250.49       CLOSEWAIT
    039B6BD4  10.47.0.229.40096       10.41.81.55.49         CLOSEWAIT
    03AD7150  10.47.0.229.65184       10.41.35.250.49        CLOSEWAIT
    039BC3A0  10.47.0.229.64702       10.41.81.55.49         CLOSEWAIT
    03B3A724  10.47.0.229.60399       10.41.81.55.49         CLOSEWAIT
    037145E0  10.47.0.229.43951       10.41.81.55.49         CLOSEWAIT
    03955EDC  10.47.0.229.29015       161.61.35.250.49       TIMEWAIT
    0365FB34  10.47.0.229.13961       10.41.81.55.49         CLOSEWAIT
    03828D54  10.47.0.229.12743       10.41.81.55.49         CLOSEWAIT
    037DB40C  10.47.0.229.23708       10.41.81.55.49         CLOSEWAIT
    TCB       Local Address           Foreign Address        (state)
    039AF814  10.47.0.229.15100       10.41.81.55.49         CLOSEWAIT
    0392E344  10.47.0.229.23399       10.41.35.250.49        CLOSEWAIT
    0393DC3C  10.47.0.229.15393       161.61.35.250.49       CLOSEWAIT
    03AD85D0  10.47.0.229.40932       161.61.35.250.49       TIMEWAIT
    039574CC  10.47.0.229.25935       10.41.35.250.49        CLOSEWAIT
    03738B74  10.47.0.229.58656       10.41.81.55.49         CLOSEWAIT
    039AD91C  10.47.0.229.56760       10.41.81.55.49         CLOSEWAIT
    03B3BC70  10.47.0.229.15058       10.41.81.55.49         CLOSEWAIT
    03B2DC54  10.47.0.229.51131       161.61.35.250.49       CLOSEWAIT
    03B393F0  10.47.0.229.11957       10.41.35.250.49        CLOSEWAIT
    039B2610  10.47.0.229.33728       10.41.81.55.49         CLOSEWAIT
    03B311EC  10.47.0.229.18047       10.41.81.55.49         CLOSEWAIT
    039A8E04  10.47.0.229.52022       161.61.35.250.49       CLOSEWAIT
    0365D460  10.47.0.229.12241       10.41.81.55.49         CLOSEWAIT
    03B33E78  10.47.0.229.47640       10.41.81.55.49         CLOSEWAIT
    0372C128  10.47.0.229.60323       10.41.81.55.49         CLOSEWAIT
    03661CD8  10.47.0.229.39923       10.41.81.55.49         CLOSEWAIT
    0393C73C  10.47.0.229.41864       10.41.35.250.49        CLOSEWAIT
    03829584  10.47.0.229.56673       161.61.35.55.49        CLOSEWAIT
    0362AC10  10.47.0.229.31952       10.41.81.55.49         CLOSEWAIT
    039BF078  10.47.0.229.22636       10.41.81.55.49         CLOSEWAIT
    TCB       Local Address           Foreign Address        (state)
    0365CF8C  10.47.0.229.14476       10.41.81.55.49         CLOSEWAIT
    039B443C  10.47.0.229.59226       10.41.81.55.49         CLOSEWAIT
    0393E794  10.47.0.229.56282       10.41.35.250.49        CLOSEWAIT
    03657740  10.47.0.229.25769       10.41.81.55.49         CLOSEWAIT
    03B2F6E8  10.47.0.229.19328       10.41.81.55.49         CLOSEWAIT
    0373AC88  10.47.0.229.25766       10.41.81.55.49         CLOSEWAIT
    039B213C  10.47.0.229.28882       10.41.81.55.49         CLOSEWAIT
    039C07AC  10.47.0.229.38201       10.41.81.55.49         CLOSEWAIT
    03AD8DD0  10.47.0.229.23002       10.41.35.250.49        CLOSEWAIT
    03739048  10.47.0.229.29572       10.41.35.250.49        CLOSEWAIT
    039BA464  10.47.0.229.32273       10.41.81.55.49         CLOSEWAIT
    03B31E6C  10.47.0.229.32521       10.41.81.55.49         CLOSEWAIT
    0365EBE0  10.47.0.229.41319       10.41.81.55.49         CLOSEWAIT
    03938804  10.47.0.229.62841       10.41.35.250.49        CLOSEWAIT
    039A1AF8  10.47.0.229.12758       10.41.81.55.49         CLOSEWAIT
    039B7DE4  10.47.0.229.20921       10.41.81.55.49         CLOSEWAIT
    036549F8  10.47.0.229.51903       10.41.81.55.49         CLOSEWAIT
    03714CC8  10.47.0.229.45145       10.41.81.55.49         CLOSEWAIT
    037425F8  10.47.0.229.56492       10.41.81.55.49         CLOSEWAIT
    03B39D74  10.47.0.229.18174       10.41.81.55.49         CLOSEWAIT

Maybe you are looking for

  • Top 10 feature requests for reliability

    As per the Terms of Use: Post constructive comments and questions. Unless otherwise noted, your Submission should either be a technical support question or a technical support answer. Feedback about new feature requests or product enhancements are we

  • Adobe Document Services Architecture NW04s

    All, I am working at a customer that will be using Adobe Document Services for interactive forms. The customer has several existing SAP applications but for this project it was recommended to configure the ADS on the SRM server (java stack is require

  • Undefined method addEventlistener

    ERRORS ON LINE 10 AND 11 1061: Call to a possibly undefined method addEventlistener through a reference with static type FunButton. package import flash.display.MovieClip; import flash.events.MouseEvent; public class FunButton extends MovieClip publi

  • Exception value in early warning system.

    Dear all, We are using R/3 4.7. My user has a condition in which for every 10,000 numbers made as goods reciept from production (101) movement , system should trigger a mail to the respective user i.d. I tried to create this condition using early war

  • RE: (forte-users) Distributing library - What could preventmy li b fro

    Hi Jean.. I remotely remember seeing this kind of a problem before. I think you can start by cleaning your environment. You can do this by: 1) Exporting your environment definition from econsole or using escript. The .edf file goes into the forte_roo