Cisco C220 SNMP query for overall status

Hello all,
I would like to know how to check the "overall state" of the UCS C220 M3 rackmount server.
I have searched and walked through a lot of OID, but I can't find which one is the "Overall Server Status" for example ?
The goal is to poll the main indicator under "Server Status" with nagios and rise an alert when something is wrong.
Anyone can help me ?
Thanks in advance

Bump !
No idea ?
I'm sure a lot of people monitors their C220 series servers... How do you do ?
Any help appreciated, thanks :)

Similar Messages

  • SNMP Query for Byspass Status (AIP5)

    I'd like to monitor the state of Bypass mode for the ASA-SSC-AIP-5 and would like to know if I can check this with SNMP and if so, which OID.
    I started messing with SNMP and the SSC5 a while back and started a thread about snmpwalk causing it to crash.  After that, I never really picked the project back up.
    I've been known to miss the obvious every now and then, but I was dissapointed to see that there wasn't an (obvious) way for the device to alert you when it automatically goes into bypass mode.  This should be a feature request.

    IPS provides SNMP traps for different interface conditions like link going down or up, traffic bypass started, etc. Below is one such example
    Received SNMPv2c Trap: Community: "public"
    From: 10.89.149.204 mib_2.1.3.0 = 38429472
    snmpModules.1.1.4.1.0 = ciscoMgmt.138.2.0.1
    ciscoMgmt.138.1.3.3.1.3 = 3                      <====    index can be mapped to index obtained from snmpwalk
    ciscoMgmt.138.1.3.3.1.4 = 5                      <====    Traffic bypass started
    ciscoMgmt.138.1.3.3.1.5 = 4
    ciscoMgmt.138.1.3.3.1.6 = 38429472
    All you need to do is enable sending traps from the sensor.
    qssp-8085(config)# service notification
    qssp-8085(config-not)# enable-set-get true
    qssp-8085(config-not)# enable-notification true
    qssp-8085(config-not)# read-only-community public
    qssp-8085(config-not)# read-write-community private
    qssp-8085(config-not)# trap-destinations x.x.x.x           <===== trap destination
    qssp-8085(config-not-tra)# exit
    qssp-8085(config-not)# exit
    You can configure separate community name under trap-destination. If not provided then the read-write-community will be used to send with the trap.
    Hope this helps
    Madhu

  • Query for job status using Web Services in BODI

    Hello,
    I am starting a Batch job in DI using Web Services, getting the following response from DI:
    Code:
    <soapenv:Envelope
        xmlns:soapenv="http://schemas.xmlsoap.org/soap/envelope/"
        xmlns:xsd="http://www.w3.org/2001/XMLSchema"
        xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
        <soapenv:Body>
            <BatchJobResponse>
                <pid>704</pid>       
                <cid>26</cid>       
            </BatchJobResponse>
        </soapenv:Body>
    </soapenv:Envelope>
    How can I know the status of the started job?
    How can I know if the job execution finished with success or not?
    I did not find in WSDL file any method to query for job or service status...
    Thank you in advance,
    Adrian Mitrica

    Did you ever get this figured out?  I am having exactly the same problem in code generated by VS, with the BAPIRET2 structure.
    Any help you could provide would be greatly appreciated.
    Thanks!
    Leighton Wingerd
    Adirondack Solutions, Inc.
    [email protected]

  • Need SNMP OID for MSTP status in Cisco SG300-28MP 28-port Gigabit Max-PoE Managed Switch

    Hi,
    I have configured redundant network using two Cisco SG300-28MP 28-port Gigabit Max-PoE Managed Switch through MSTP & it's working fine.
    I need OID of MSTP status from which I can monitor which Switch is active and which one is in standby mode.
    Please help.
    Thanks,
    Harsha 

    Hi Harsha,
    check these OID's:
    http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?objectInput=1.3.6.1.4.1.9.9.500.1.2.1.1.6&translate=Translate&submitValue=SUBMIT
    http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?objectInput=cRFStatusUnitState&translate=Translate&submitValue=SUBMIT&submitClicked=true
    Thanks-
    Afroz
    **Ratings Encourages Contributors ***

  • E Recruitment : Report/Query for Activity Status

    Hi,
    Is there a standard report/query which shows all the activities with their corresponding status and due dates.
    If not, can someone guide me how to capture this data, in terms of tables which store this details.
    Any inputs on this please....
    Thanks
    MM
    Edited by: abaphr_mm on Oct 29, 2010 6:56 PM

    Hi,
    could you give some additional information on your requirement?
    If you need support for the every day work of the recruiter there are standard bsp applications (up to ehp 3) and work sets (for ehp 4 sp 4 and higher) which show the planned activities and planned correspondences for them.
    If you need some statistic over all recruiters the are some infosets but I never used them as they never met the requirements in my projects. I'd probably write some report reading the activity infotypes (tables HRP5135 to HRP5142/43 or 45 depending on your e-rec release) directly. For statistics please keep in mind that recruiters tend to not complting all of their activities. So you might gather tons of data from candidacies / applications which belong to requisitions which are already closed.
    Best regards
    Roman

  • SNMP query for multicast group count

    I want to get the total number of multicast groups on a switch. Is there an oid that will give me the info (ie. the number that's given by "show ip igmp snooping groups count")? If there is no oid, is there a way query the  groups (show ip igmp snooping groups)? I'm thinking with the 2nd option I might be able to count the number of entries returned by an snmpwalk or something and turn that into a number.
    Right now i'm logging into the switch with a script and running the command but that might be a problem with all those logins (only every 5 minutes though) so I'd like to do this via SNMP if possible.
    Any ideas?
    Thanks

    Works just fine!!!
    Thanks!
    LA$$E
    Hi,
    Well, at the very least, you can create a formula
    column in your break group using a combination of the
    same where clause as your original query and the
    break values for the group so that you are getting
    the correct records. If you have it in the break
    group, then it will execute for each record in that
    group.
    Hope that helps,
    Toby

  • SNMP Query for active tunnels inaccurate

    Hi,
    I use the following OID: 1.3.6.1.4.1.9.9.171.1.3.1.1.0 to query my 3005 concentrator for the number of active tunnels. The number of tunnels averages around 4-8 at a time, but about 40% of the time, the returned value is 85. This is skewing my results.
    This may coincide with enabling WebVPN, but even the statistics on the web pages of the 3005 never even come close to this value.
    Any suggestions?
    Thanks,
    Dave

    show counters output might help you in analysis

  • Snmp query for TenGigE data counters C4510R+E?

    Dear community. With the risk of sounding like an idiot I turn to you:
    I'm having slight challenges reading the data counters for a ten gigabit Ethernet interfaces on our C4510R+E w/sup8 with this IOS:
    bootflash:/cat4500es8-universalk9.SPA.03.03.00.XO.151-1.XO.bin
    running snmpwalk on ifindex reveals all indices properly, i.e:
    IF-MIB::ifName.1 = STRING: Fa1
    IF-MIB::ifName.2 = STRING: Gi1/1
    IF-MIB::ifName.3 = STRING: Gi1/2
    IF-MIB::ifName.4 = STRING: Gi1/3
    …etc…
    IF-MIB::ifName.259 = STRING: VLAN-601
    IF-MIB::ifName.260 = STRING: VLAN-876
    IF-MIB::ifName.261 = STRING: Te5/1--Uncontrolled
    IF-MIB::ifName.262 = STRING: Te5/1--Controlled
    ...etc...
    but when trying to see the octet counts from for example ifindex 261 or 262 I get no results at all:
    ...etc...
    IF-MIB::ifHCInOctets.230 = Counter64: 0
    IF-MIB::ifHCInOctets.231 = Counter64: 0
    NOTE: no ifIndex 261 or 262
    IF-MIB::ifHCInOctets.293 = Counter64: 0
    IF-MIB::ifHCInOctets.294 = Counter64: 0
    ...etc...
    All other physical interfaces show their values just fine - just not the TenGigE's.
    so, dear community: is this a problem, feature or something that can be configured to work differently? or is it just me :-) googling something like "snmp tengigabitethernet counters" brings up mostly problems with the max data rate but in my case the snmp values do not seem to exist at all.
    Thanks in advance,
    JukkaK

    It may be helpful to see the entire output/snmpwalk for ifTable and ifXTable for this device to see if all the data is missing for these indexes/TE interfaces.
    Many older IOS has some issues where the details for a perticular linecards and its associated interfaces were missing from Switch.
    Many times it worked after reseat of Linecard or Reboot of the entire device. As these are not the easy and not the first choice for many, lets check the outputs first.
    Also from the switch, please share output for device for show snmp mib ifmib ifindex command.
    -Thanks
    Vinod
    **Encourage Contributors. RATE Them.**

  • PR Status = 04 : FOR OVERALL RELEASE

    Hi Friends ,
    We have PR status in PR ITEM DETAILS (Me53n) - STATUS Tab , which can have following status
    1)Version in Process
    2) Active
    3) In release
    4) release completed
    5) For Overall Release
    6) Release refused
    I wanted to know the meaning of "FOR OVERALL RELEASE" here and when this status gets updated in PR.
    Like to share, we have OVERALL release Strategy ( NOT Item LEVEL) implemented for PRs
    Regards
    Shrey

    Thx for reply ...
    But here in my case , the status "FOR OVERALL RELEASE" is only being appeared for few PRs, for all other PRs either the status is "IN Release" or "Release Completed".
    Although all PRs are subjected to OVERALL Release.
    I couldn't identify the reason why only few PRs have "FOR OVERALL RELEASE".Also like to share all such PRs has already been approved by approvers but instead of "Release complete" , system is showing me status "FOR OVERALL Release"
    Appreciate if you could let me know the reason for the same.\
    regards
    Shrey

  • QUERY FOR STATUS OF SALES ORDER

    Hi Experts,
    Here my Client required one query for status of the Sales Order line item wise and by when material will be  ready after giving clients PO no. sales order NO. Clients name etc.
    Please give me guide to write this query.
    Regards
    Madhu

    Hi,
    Try this link,
    http://help.sap.com/erp2005_ehp_04/helpdata/EN/d2/cb4759455611d189710000e8322d00/frameset.htm
    Cheers,
    Shailabh

  • OIM sql Query for getting the status of the task which got failed

    Hi Everyone,
    We have a requirement like we need to get the status of a particular task(say Create User in OID resource - Completed\Rejected status) for the particular user.We are able to get the status of the resource provisioed to the user but not the status of the particular task getting trigerred for the user.can someone put some light on this.We need to get the SQL query for this.
    Thanks in Advance.
    Regards,
    MKN

    Hi
    Use this sample query to get the task status, also check the cooments
    SELECT USR.USR_LOGIN, OSI.SCH_KEY,SCH.SCH_STATUS,STA.STA_BUCKET FROM
    OSI,SCH,STA,MIL,TOS,PKG,OIU,USR,OBJ,OST
    WHERE OSI.MIL_KEY=MIL.MIL_KEY
    AND SCH.SCH_KEY=OSI.SCH_KEY
    AND STA.STA_STATUS=SCH.SCH_STATUS
    AND TOS.PKG_KEY=PKG.PKG_KEY
    AND MIL.TOS_KEY=TOS.TOS_KEY
    AND OIU.USR_KEY=USR.USR_KEY
    AND OIU.OST_KEY=OST.OST_KEY
    AND OST.OBJ_KEY=OBJ.OBJ_KEY
    AND OSI.ORC_KEY=OIU.ORC_KEY
    AND OBJ.OBJ_NAME='AD User'
    AND OST.OST_STATUS = 'Provisioning' -- filter accordinglly
    AND STA.STA_BUCKET = 'Pending' -- filter accordinglly
    AND PKG.PKG_NAME='AD User' -- filter accordinglly
    AND MIL.MIL_NAME='System Validation' ---- filter accordinglly
    Thanks,
    Kuldeep

  • Need function module for Sales order overall status

    Dear Team,
    Our requriement is we need to capture sales orders overall status 'compleated' in header and item datat details.
    Could you please let me know what are function modules available for to get the over all status for sales orders, (header and item)
    Thanks & Regards,
    MK.

    Hi MK,
    Use any of this FMs.
    C1CE_VBUK_READ
    SD_VBUP_READ_WITH_VBELN
    WCB_VBUK_READ
    Note that the values are in table VBUK and you can do a select statement from that table to get what you need.
    Regards,
    Peter

  • Overall Status for sales order line & header on a service order

    Hello,
    I have a service order that has been fully delivered and invoiced but the overall status for that line & header is "In process".
    I am unclear which area of configuration determines / controls the overall status.  Can anyone help point me in the right direction?
    Thanks.

    Hi Vicky,
    Check the completion rule in the item category of the order?
    Regards,
    Raghu.

  • NI License manager does not start; says it's querying for current license status

    I currently have the evaluation version of Labview. I tried to use a volume license from my university by typing in the server name in NI License Manager, but after that, whenever I try to open the license manager, it looks like it's stuck saying "querying for the current license status" and never actually opens. Also, when I try to open Labview, it freezes during the setup finalization. I realized afterward that students don't have access to the university license for their own PC's, so I can't use that volume license anyway. 
    I uninstalled everything having to do with NI on my PC and reinstalled the evaluation version of Labview, but the same problem still exists. Is there anything I could do besides erasing my hard drive? 
    Solved!
    Go to Solution.

    Hi amize,
    When you say the same problem still exists, is it both the NI License Manager and LabVIEW that are still having the issues? When you open the License Manager and it is not actually opening does that mean you cannot interact with it or the licenses never finish loading in the tree view on the left hand side. If you do have access to the Options menu, open preferences and make sure you have deselected "Use Volume License Servers". At some point, if the windows is not interactive, it should timeout with attempting to make its server connection, especially if you are disconnected from any network connection.
    Also, how long do you wait when you open LabVIEW and see the setup screen? Does it just become unresponsive?
    If you could follow up with that information it would be much appreciated
    Regards,
    James W.
    Applications Engineer
    National Instruments

  • Report needed for overall view of update compliancy

    I've been asked to provide a custom report to give an overall status for the update compliancy for the servers in place.
    Have been fiddling about in sql mgmt studio and kind of understand where to get the information from, but am missing something.  so I was hoping someone could point me in the right direction
    I realize that this kind of report might take some querying time, but this is what the customer wants: instead of him going to the builtin report compliance 7 (category sw updates - compliance A) where he has to select a collection AND a baseline AND a compliance
    status, he wants to obtain a list of all server systems being compliant to some server baselines and a list of all server systems being non-compliant to some server baselines
    currently the sqlcode i Have to show the compliant servers, is:
    SELECT
         v_R_System.Name0
    AS Servername,
    v_GS_OPERATING_SYSTEM.Caption0
    AS OS,
    v_ConfigurationItems.CI_ID,
    v_AuthListInfo.Title,
    v_StateNames.TopicType,
                          v_StateNames
    .StateID,
    v_StateNames.StateName
    FROM
             v_ConfigurationItems
    INNER
    JOIN
                          v_AuthListInfo
    ON v_ConfigurationItems.CI_ID
    = v_AuthListInfo.CI_ID
    CROSS
    JOIN
                          v_R_System
    INNER
    JOIN
                          v_GS_OPERATING_SYSTEM
    ON v_R_System.ResourceID
    = v_GS_OPERATING_SYSTEM.ResourceID
    CROSS
    JOIN
                          v_StateNames
    WHERE    
    (v_R_System.Client0
    = 1) 
    AND(v_R_System.Operating_System_Name_and0
    LIKE
    '%server%')
    AND
    (v_AuthListInfo.Title
    LIKE
    '%server%')
    AND(v_StateNames.TopicType
    = 300)
    AND(v_StateNames.StateID
    =
    '1')
    ORDER
    BY Servername
    BUT if I now change the stateid to 2 in the query I get the same amount of rows back (being 134 servers with an sccm client times 4 server update groups)
    so my problem is: how and when do i make the correct join here ?

    I was thinking that it might be better to use the assignmentstate views, and I quickly came up with this alternative:
    SELECT
         v_R_System.Name0
    AS ServerName,
    v_CIAssignment.AssignmentName
    as
    'Deployment Name',
    v_StateNames.StateName
    FROM
             v_AssignmentState_Combined
    INNER
    JOIN
                          v_R_System
    ON v_AssignmentState_Combined.ResourceID
    = v_R_System.ResourceID
    INNER
    JOIN
                          v_FullCollectionMembership
    ON v_R_System.ResourceID
    = v_FullCollectionMembership.ResourceID
    INNER
    JOIN
                          v_CIAssignment
    ON v_AssignmentState_Combined.AssignmentID
    = v_CIAssignment.AssignmentID
    INNER
    JOIN
                          v_StateNames
    ON v_AssignmentState_Combined.StateID
    = v_StateNames.StateID
    WHERE    
    (v_StateNames.TopicType
    = 300)
    AND(v_StateNames.StateID
    = 1
    OR
                          v_StateNames
    .StateID
    = 2)
    AND(v_FullCollectionMembership.CollectionID
    =
    N'D01003FE')
    ORDER
    BY servername
    at first glance this produces what I want, let me check with the customer.
    you guys agree with that or not?

Maybe you are looking for