Cisco C90 Codec with Mulitple camera

Hello,
I'm experiencing an issue with the secondary camera self-view on C90 codec(v7.0.2), The both the camera's are connected to HDMI1 and HDMI2.
Iam getting selfview from main camera only. Both camera's are daisy chained and able to control.
Does there any configuration required to enable the secondary camera from codec to the self view.
Both the camera's are Precision 1080 12X.
Tnx
Bobby/

You can change the main camera source using any of the following options:
The remote from within the menu (can't remember the exact locations).
The web interface, on the call control page, as well as the system configuration page under the video options.
The serial port or SSH, you can issue commands directly to the codec to change the camera source using xConfiguration Video MainVideoSource.
Remember as Wayne stated, you can only have one camera selected at any one time, as a result, you'll only see whichever camera is selected as the main source, unless you use TC Console to composite the multiple cameras into one stream to be displayed on the screen.
https://developer.cisco.com/site/collaboration/telepresence/av-integrator/tools/tc-console/tc-console.gsp

Similar Messages

Recording for Cisco IP Phones and Cisco C90 Codec

Hello
We are looking for a solution that is capable to record both Cisco IP Phones and Cisco Codec C90.
We are using CUCM 9.X for IP Phones and VCS 7.X for Cisco Codecs.
Is their any third party solution available for both the requirements or do i have to go with TCS and any other third party recording solution.
Thanks & Regards
Aniket Patil

My reply may be too late to be of any help to you, but for the benefit of others:
Be sure you understand the different types of PoE out there. The Linksys PoE switch only supports the newer IEEE 802.3af PoE standard.
The 7940, 7960, 7905 and other older Cisco phones only support Cisco pre-standard PoE and thus will not work with the 802.3af Linksys Switch.
To use this switch, you will need to make sure you are using the newer 7070, 7961, 7941 phones with support both pre-standard and 802.3af PoE.
All the best,
John

Cisco SX80 Codec ERROR: Camera Pairing

On camera 2 I get the error message "
ERROR: Camera PairingCamera pairing failed: lost connection with camera
if I get it connected it stays connected for less than 15 minutes before it drops offline.

Some simple things you can try:
Check that your ethernet cable is plugged in securely at both ends.
If the problem persists, try another, known working cable between the two and see if the error stays or goes away.
Swap Camera 1 and Camera 2 around to see if the issue stays with the camera, or the connection.
Wayne
Please remember to rate responses and to mark your question as answered if appropriate.

Avid codec with premiere pro cs4

has anyone used Avid DnxHD codec with premiere? I cant change the settings of the codec and i wanted to see how much better it would be compared to Apple ProRes422(HQ). Has anyone got it to work or is it a no go? and how come i cant edit the settings of ProRes422?
I use premiere pro instead of Final cut pro because my camera records AVCHD and i dont want to loose any quality in which log and transfer in final cut pro will do.

I believe that DNxHD is a slight modicum of "better" than ProRes--some video guru somewhere on the web did a comparison of the two, and DNxHD came out on top. I personally haven't done a comparison, so I have to take that for what it's worth. I think that for most mere mortals, the differences are going to be minuscule and quite inconsequential--but you might be able to detect the difference ;)
The only way to not compress your video again is, well, to not compress it again. In other words, use something like Apple Animation which will give you a bit-for-bit, pixel-for-pixel copy of your original. Of course, your hard drive will fill up and explode, depending on the length of your export, but that's the trade-off for pristine quality.
Bear in mind that the AVCHD you're working with is already highly compressed. Even at its minimum compression (24Mbps), there's still quite a bit of squeezing going on, as well as other processing going on intrinsic to H.264 that makes it look so purty, but be so damned hard to edit. Again, this is the trade-off. I think you need to carefully weigh the importance of saving a few fleeting pixels over the mountain of hard drive space that you'll need to store these massive exports. You get six of one, or a half dozen of the other.
Since you've got the Master collection, I'd suggest sending your finished PPro timeline to AE via Dynamic Link (lasso your clips, right-click, and hit "Send to After Effects"). You don't need to change anything there; just put that comp into the render queue, tweak your settings for DNxHD/ProRes export, and go to town. Like Josh, I can't speak to ProRes because I'm on Windows and we can only play it back, but you should be able to change its settings there. If not, go with DNxHD because you have full customization of the codec at your fingertips--colorspace included.
Regarding the audio: don't sweat that AE can't export or deal with 5.1. Just export that from PPro, either as a mix (if you can do that--I'm not sure as I don't work in 5.1) or as 6 mono files. Then, just store those with the video rendered out of AE. You can always stitch everything back together later in your NLE of choice, and export/render out a distribution format. Make it easy on yourself!

Cisco WVC2300 Business Internet Video Camera I/O ports power lights on/off ?

What is needed to make it possible to enable the Cisco WVC2300 Business Internet Video Camera to use it's I/O ports to power lights on/off ?

Talking to our Development team. They replied to me with this.
Depends on the device the camera is connected to, if it's some sort of a transistor or a relay then it shouldn't be a problem. Think of the camera as a simple relay, all it does is turn on and off, so if you need to turn on and off a light you'll need to limit the switch device in such a way that the connection from the camera to the device does not exceed the output voltage requirement on the camera (If they remember correctly 24V.2A).
I hope this helps.
I believe any of our authorized resellers might have kits or equipment that can help with this.
Eric Moyers
Cisco Network Support Engineer
1-866-606-1866

Photos. They are on my macBook, backed up on time machine. Copied them (hours and hours) to external hard drive. They are now in alphabetical order (19,000 of them) NOT IN THEIR EVENTS or date order-and have been taken with different cameras- help!!!!!!

Photos.
They are on my macBook, backed up on time machine. There are 19,000+ of them, some rescued from a pc crash- which I used the nifty iPhoto to put back into date order.
I want to take them all off my laptop, now............as I need to use it for WORK!!
Copied them (hours and hours) to another external hard drive.
They are now in alphabetical order (all 19,000+ of them) NOT IN THEIR EVENTS or date order. (-They have also been taken with different cameras over the years and some of the generic camera numbering remains.)
I have tried to copy them (only a few as an experiment) one event at a time, but that again "opens up" the Event "folder" and tips them out as individuals and therefore just lists image letters and numbers alphabetically.
How can I copy
the whole library still in "Events" to an external hard drive?
the folders/albums I have already made on to this hard drive?
and how can I add to this back up monthly, again keeping events and folders separate and updated?
Mac is so user friendly - there must be a way.........
Thanks

UPDATE : I have re-installed from disk, various apps that were no longer functioning such as iLife, iWork etc. So, I now can access my photos again.
Also, I had to re-install all the software for my printer ( Stylus Pro 4880 ) and reset it so the printer is working again.
Photoshop CS4 won't open. I think I will have to get in touch with Adobe as basically, I guess they have a built-in "blocker" which prevents me from opening the app as the license is for only 1 user and having re-installed the OS, there are now, in effect, 2 users ( Me and Me 1, I think ).
So, having added on a new external HD, Time Machine has made a copy of most of the files, folders, apps etc onto the external HD. The internal HD is still nearly full ( 220 GBs out of 232 GBs ).
I am guessing the way to go now in order to free up space on the internal HD is to delete/trash older photos from my iPhoto library and hope that if needed, I will be able to access them on the external HD.
Am I correct ? Please advise before I do something I will regret.
Thanks, Sean.

ASA , Cisco VPN client with RADIUS authentication

Hi,
I have configured ASA for Cisco VPN client with RADIUS authentication using Windows 2003 IAS.
All seems to be working I get connected and authenticated. However even I use user name and password from Active Directory when connecting with Cisco VPN client I still have to provide these credentials once again when accessing domain resources.
Should it work like this? Would it be possible to configure ASA/IAS/VPN client in such a way so I enter user name/password just once when connecting and getting access to domain resources straight away?
Thank you.
Kind regards,
Alex

Hi Alex,
It is working as it should.
You can enable the vpn client to start vpn before logon. That way you login to vpn and then logon to the domain. However, you are still entering credentials twice ( vpn and domain) but you have access to domain resources and profiles.
thanks
John

How do I move photos around that I took with the camera?

Alright I have a bunch of photos in the "Camera Roll" that I took with the camera phone.
It defaults to the Camera Roll folder, but how do I move them to other folders on the phone?
Can I do multiple pictures at once?
Or do they have to be moved one by one?

If you disabled the Camera & Scanner Wizard from launching automatically when a digital camera is connected - when your iPhone includes photos that were captured by your iPhone or when photos are available in your iPhone's Camera Roll, the iPhone is also detected as a digital camera when connected to your computer - you can try this.
http://www.microsoft.com/downloads/details.aspx?familyid=C680A7B6-E8FA-45C4-A171 -1B389CFACDAD&displaylang=en

HT4623 my IPod Touch is a generation 3 with a camera and when i go into my settings and try to do what the instructions on your website say but in general i only have About and then the rest of the bars but i don't have one that says Software Update

my Ipod Touch is a generation 3 with a camera and when i go into the settings to look for the Software Update bar i don't have one

If you have cameras then you have 4G iPod. To update connect to your computer and update via iTunes
iOS 4: Updating your device to iOS 5 or later
- A 4G to 6.1.5 Requires iTunes version 10.7 or later. For a Mac, that requires a Mac with OSX 10.6.8 or later

Is there a known problem with some cameras, e.g. the E-410?

I bought an Olympus E-410 yesterday, took a few pictures, and then wanted to load them onto my eMac. But the computer never saw the camera. The screen on the camera said "One moment" forever. I had installed the software that came with the camera, but that said "When iPhoto comes up close it and open [the Olympus software]".
I installed it on my Windows machine, and it saw the camera as an installed device, and the Olympus software worked fine, with the same cable.
I would have expected it to work because it is explicitly mentioned here: http://docs.info.apple.com/article.html?artnum=306297
We regularly add pictures from my wife's Canon Powershot A80, into iPhoto, and it works fine.
Any helpful ideas?
Message was edited by: Logistes

No! I was wrong. My iPod showed the same symptom. The common denominator is that the Maxtor was plugged in at the same time. I had no problem with the new camera today, after removing the Maxtor's USB.
That's a relief, but not perfect. I guess I should have got a Firewire HDD

On holidays we took pictures with two cameras and an iPad. I put everithing on my PC. Rearranged them by date, time and or subject putting a number in front of the picture name. I synchronised with my iPad and my pictures show in misselaneous order. Help

We took pictures during oue holidays with two cameras and an iPad. I put all the pictures on my PC and reorganized them by date, time and/or subject, By putting a number in front of the picture name. Then I synced with my iPad. All the pictures show in a misselaneous order. What went or did I wrong?

You did nothing wrong, but the photo app puts stuff in chronological order.
You can look for another app. Afraid I don't have one to suggest, but I do understand that other apps will sort photos differently.

I can no longer download photos to my ipad with the camera attachment. the message says thats its using too much power. i have a 100% charge and i used it before and it worked fine.

I can no longer upload photos with the camera attachment. I am getting an error saying the device uses too much power. I have used the device before. Is there anything that can be done to fix this problem?

You don't actually say what the problem is, but maybe this can help:
USB and Firewire information:
http://support.apple.com/kb/HT1151?viewlocale=en_US
http://support.apple.com/kb/HT4049?viewlocale=en_US

Terrible customer service, and no help with defective camera

Madams and Sirs,
This camera (see below) was a Christmas present, and we discovered first last week that it had a manufacturing defect. (one of the small tabs holding the case half together got installed in a pinched way.)
Best Buy has always had fantastic customer service, and we have been very happy. We have spend many thousand dollars in your store every year. So we were sure the store would have a solution.
We took it in to your store #1423 on Curtner in San Jose to try to exchange or replace under warranty.
I understand you sometimes you are not able to help a customer, but this email is first about the shock I got when I spoke with Megan in customer service.
As many customers in Silicon Valley, I am an engineering manager, and we have performed destructive testing on many of our own products. The defect on this camera is obviously a manufacturing defect, and not possible to be caused by poor handling. This is very obvious.
Megan told me with other employees as well as my son listening next to me that I was a liar, and that the damage was caused by abuse, and not a defect. I tried to explain that was not possible, and she interrupted me, and again said that i was not telling the truth, and that the assembly error was caused by us.
I then asked if it was possible to have the matter reviewed by the store manager, and she responded she was the store manager.
I left with the camera, and the matter unresolved, and had to explain to my son that I was not a liar, and that Megan must be wrong and "some people just have a bad day sometimes".
I will not be spoken to with insults like that, and I can no longer go to your store with my kids, and if my employees treated any customer the way Megan did, I would make sure she received training to correct this. If the store manager have this attitude to customers, the entire organisation usually follows, and I will not be a customer in a store like that.
1. Please help resolve this issue.Order number: {removed per forum guidelines}

Hello erikev,
Cameras are nice to have, especially with young children, so I can imagine how frustrating it can be to find yourself with a pinched casing. When something goes wrong, it’s never a fun situation, and while it may not be something we can necessarily help with, great customer service should still be provided. It sounds like this didn’t happen the way we hoped, and I’m sorry this was at your expense.
As this situation is definitely concerning, I looked into your account to see how I might be able to assist. However, I have found your concerns have reached Terrance with our executive support team. He is currently looking into your situation and should contact you once more information is available. From here, Terrance will be your first point of contact.
Hopefully he can find a good resolution for you,
Alex|Social Media Specialist | Best Buy® Corporate
Private Message

Do any one know how much it is to get the new ipod touch with the camera if you trade in your old ipod touch?

do any one know how much it is to get the new ipod touch with the camera if you trade in your old ipod touch?

Sounds like you need a new battery. I would make an appointment at the Genius Bar of an Apple store to confirm. Apple will replace the battery for $79. A third-party place like the folloing may be less expensive. Google for more places.
iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens
You can also replace it yourself if you are so inclined. For parts and instruction:
iFixit: The free repair manual

I had Leopard on may Mac. I upgraded to Mountain Lion using Snow Leopard. I can't use my video with Mountain Lion. Can I load Snow Leopard on an external hard drive so I can use it with my camera?

I had Leopard on may Mac. I upgraded to Mountain Lion using Snow Leopard. I can't use my video with Mountain Lion. Can I load Snow Leopard on an external hard drive so I can use it with my camera?

First, you cannot do this if you have a Boot Camp partition.
Second: Create a new partition.
1. Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
After the main menu appears select Disk Utility and click on the Continue button. Select the hard drive's main entry then click on the Partition tab in the DU main window.
2. You should see the graphical sizing window showing the existing partitions. A portion may appear as a blue rectangle representing the used space on a partition.
3. In the lower right corner of the sizing rectangle for each partition is a resizing gadget. Select it with the mouse and move the bottom of the rectangle upwards until you have reduced the existing partition enough to create the desired new volume's size. The space below the resized partition will appear gray. Click on the Apply button and wait until the process has completed. (Note: You can only make a partition smaller in order to create new free space.)
4. Click on the [+] button below the sizing window to add a new partition in the gray space you freed up. Give the new volume a name, if you wish, then click on the Apply button. Wait until the process has completed.
You should now have a new volume on the drive.
It would be wise to have a backup of your current system as resizing is not necessarily free of risk for data loss. Your drive must have sufficient contiguous free space for this process to work.
Third: Install Snow Leopard.
Boot from your Snow Leopard DVD. Follow instructions for installation being sure that before you actually install Snow Leopard you have selected the new partition as your target destination.
Booting From An OS X Installer Disc
1. Insert OS X Installer Disc into the optical drive.
2. Restart the computer.
3. Immediately after the chime press and hold down the "C" key.
4. Release the key when the spinning gear below the dark gray Apple logo
appears.
5. Wait for installer to finish loading.

Cisco C90 Codec with Mulitple camera

Similar Messages

Maybe you are looking for