Cisco CallManager 5.1.3 Migration to CUCM 8.6
Hello
I am trying to migrate a Cisco Call Manager v5.1.3 to a new CUCM v 8.6 running on a VM.
I made a DSR backup from Call Manager v5.1.3 and try to install it in a VM running the same version (5.1.3) but I am receiving the following error message:
At least one of the servers which was requested to be restored is not connected: CUCMPUB. This may be due to Master or Local Agent being down., Restore Completed...
Any ideas about how to upgrade this server in a VM? I would not like to upgrade the production server...
Thanks in advance
Miguel Neira
Thanks for your response
The services are running...
Backup and Restore Services
Service Name Status
Cisco DRF Master
Running
Cisco DRF Local
Running
Similar Messages
-
Does migration to CUCM 8.6 to 9.1 requires aditional Money?
Hi pals!
We just completed migration to CUCM 8.6 a year ago, we are now (we want to) moving to 9.1, we have a question, if it requires aditional money $$$$ (license), por for upgrade or just a minor patch.
Also.
Does it also requires CUC 9.1?
Does it also requires CUPS 9.1 too?
I just read the quick guide to migration and I have a loot of questions, my Cisco Parthner is really busy right now with another projects, so I Think i just get the point of this topic.
another BIG question.
When will version 10 be releaded (more less)?
I would better wait for version 10 instead version 9.1
Can you provide some interesting links?
I appreciate your time for your response, and I thank to you in advance.
regads.
john.John
You don't need to pay any money for any major CUCM upgrade as long as you have active UCSS on it. If as part of the migration to version 8.6 you purchased UCSS you are covered, otherwise you will need to pay for every major upgrade.
If you did buy UCSS then you can simply request the upgrade vie the PUT upgrade portal.
HTH,
Chris -
Migrating from CUCM 8.6 to CUCM 10.0 - Do I have to upgrade presence as well?
Hello Raees,
I've got a question regarding the Migration from CUCM 8.6 to 1.0, I went through the below "Ask the Expert" article.
https://supportforums.cisco.com/discussion/12103966/ask-expert-cisco-unified-communications-manager-cucm-version-100
My question is, the CUCM 10.0 upgrade mentions the following on page 22
"Refresh upgrade of Unified Communications Manager nodes only
Complete the high-level tasks listed in this section when you want to perform a refresh upgrade of only the
Unified Communications Manager nodes in your network. When you upgrade Unified Communications
Manager nodes without upgrading IM and Presence nodes, ensure that the installed version of the IM and
Presence Service is compatible with the new version of the Unified Communications Manager software."
I would only like to Upgrade the CUCM nodes but the client is using Presence 8.6 as well, would I have to upgrade Presence 8.6 to something else as well or can I just upgrade to CUCM 10.0 and the presence 8.6 would work with it, if I have to upgrade Presence as well then what version of Presence would I have to upgrade to and for the "Refresh Upgrade for Presence" can you mention the SKU that I got to get off the Product Upgrade Tool.
Since it's going to be a Refresh Upgrade for CUCM from 8.6 to 10.0 can you as well provide me with the SKU for the upgrade that I got to purchase, I can see two of them as follows:
UCM-10.X-SW-K9-XU=
CUCM Software Version 10.X for PUT Only, Export Unrestricted
UCM-10.X-SW-K9=
CUCM Software Version 10.X for PUT Only
Thanks
AamerThank you for the reply Chris,
I have a few more questions with regards to what you mentioned in your reply, I'd be glad if you could clarify:
I have not dealt with IMP before...
1) is it like a plugin that runs on CUCM instead of a full fledged server or is it a stand alone server like CUPS (just renamed/rebranded).... I have till date been dealing with CUPS as a stand alone server that integrates with CUCM via the CUCM -> System-> Application Server Option.
2) If it's a plug-in then how would the upgrade be done from the CUPS Stand Alone to this IMP that runs within the CUCM Server or would it be a fresh installation or some activation of services within CUCM... and if it's a stand alone server then what Upgrade Image do I need to upgrade CUPS 8.6.4 to IMP 10.0 or 10.5.
I'm sorry but the upgrade path for CUPS 8.6.4 to IMP 10.0/10.5 is not clear for me, could you help me understand the migration for CUPS 8.6.4 to IMP 10.0/10.5..... could you as well advise any documentation that shows detailed steps for the upgrade from CUPS 8.6.4 to IMP 10.0/10.5... the CUCM upgrade is clear to me from the Upgrade Guide.
Thank you
Aamer -
I plan to execute an upgrade of CUCM and CUCX from version 7.1.3.30000-1 to a version 9.1.1.20000-5 (CUCM) as well CUCX 7.0(1)SR05_Build504 to 9.0.2.10000-71(CUCX) respectively on a VMware ESXI 5.0 . I will be grateful if someone finds a little time to help me to make the upgrade plan
Cisco unified contact center express
Current version :Cisco application administration-7.0(1)SR05_Build504
pakage cisco unified ccx premium
cluster default
New version: Cisco Unified CCX Administration
System version : 9.0.2.10000-71
Cisco Unified Call Manager
Current version :sysystem version 7.1.3.30000-1
New version:system version 9.1.1.20000-5
Please check the snapshot of the current versions
Regards
Akhilesh NambiyathSince you're a partner you should be able to go here, then it's time to do some reading
https://communities.cisco.com/community/partner/collaboration/migration?view=overview
HTH
java
if this helps, please rate
www.cisco.com/go/pdihelpdesk -
Cisco Callmanager Version 9.X on Custom Made Server
Hi Cisco
May i know can we install Cisco Callmanager version 9.X on custom made server? i plan to buy one of custom made server from third party with free dos.
Then i want to buy cisco callmanager version 9.x software to install on the custom made server. Is it possible?
Since Cisco camoe out with UCS server all the callmanager was install with vmware platform. Is it possible i install the callmanager version 9.x into custom made server with free dos.
Then i install the callmanager version 9.X into the custom made server.UCS are only for virtualised applications, they are different from the old appliance based MCS servers. You'll need to buy UCS server, VMware licenses etc.
You can look into Cisco BE6k for that many users. BE6k is basically a UCS C220 server (other than small which is UCS E160D blade server) that comes as a bundled solution, with pre-installed VMware, pre-loaded software (CUCM, CUC, UCCX etc. install media) and normally a starter 25 licenses (you can buy additional add-on licenses as per need) so review the BE6K and see if that fits your needs. It comes in small, medium etc. different capacities.
I would also recommend installing the latest version of CUCM which is 10.5, if you have no particular reason to stick to 9.1.
Ref: http://www.cisco.com/c/en/us/products/collateral/unified-communications/business-edition-6000/data_sheet_c78-717454.html
Please do rate all helpful posts and mark the thread as answered if you have no other queries.
-Terry -
Cisco IP Phone 8945 not present in cucm version: 7.1.5
I am trying to add a Cisco ip phone type 8945 to a CUCM version version: 7.1.5.33900-10
The phone type 8945 does not show up in the drop down window in my Callmanger.
I am trying to find out if i need to add the new firmware for 8945 and the device package ? or only the firmware will do the job ?
SuleyHi Souley,
When you are trying to add a new model/device type you will need
to use the Device Pack
Like the latest for 7.1.5
cmterm-devicepack7.1.5.36121-2.cop.sgn
From;
http://www.cisco.com/web/software/282074299/102827/cmterm-devicepack-7_1_5_36121-2_Readme.pdf
Cheers!
Rob
"When it comes to luck you make your own "
- Springsteen -
Cisco CallManager RisPort Problem
Hi All,
In my company we are upgrading Cisco CallManager 4.1 to 5.0,In ccm5.0 How to get the Real Time Information(like Ip address of the Phone). iam using SOAP to interact with CCM 5.0 if anybody worked on this , please send me the sample code for this it is very useful for me
Thanks in advanced
Regards,
Ravindra
my personal mail id:[email protected]Create the CDR database manually by following the steps below:
Go to Start --> Microsoft SQL --> sql query analyser
Click on file -- open --- goto c:\program files\cisco\bin\ ---- select CDR --- click open and execute the sql query
Then try to install CAR again.
HTH
//Jorge -
Cisco 7821 IP Phone not registered in CUCM 9.1.2
Dear all,
We have CUCM 9.1.2.11900-12 and we have uploaded this device package: cmterm-devicepack9.1.2.12028-1.cop.sgn and reboot cluster
But the Cisco 7821 IP phone not registered in CUCM
can some one advise me?
Thanks and best regards,
TanHi
Can you please share the output for show version active from CUCM.
Please check the following thread as well:
https://supportforums.cisco.com/discussion/12030206/adding-7800-phones-cucm-8691 -
Hello.
I am sorry for bad English. At me such question:
As in "Cisco CallManager 4.1" in "Device Defaults Configuration" to add phone support cisco 7925
By default such support is not present, it is possible to look a picture in an investment.
ThanksGreetings.
Yes, on tftp all is good, all files for an insertion 7925 are present. Here the list of files: CP7925G-1.3.2.LOADS, TNUXH-1.3.2.SBN, TNUXRH-1.3.2.SBN, SYSH-1.3.2.SBN, WLANH-1.3.2.SBN, APPSH-1.3.2.SBN, GUIH-1.3.2.SBN.
In adjustment «Device Defaults Configuration» under cisco 7921 has substituted file CP7925G-1.3.2.LOADS, does not work, on phone the message «failure of updating of microprocessor maintenance» stands out
And devices cisco 7921 at reboot begin перепрошиваться under 7925 but too there is an error.
While leaves nothing!!!.
Like all I do correctly. -
Cisco CallManager 5.x Service Parameters
Nothing shows in Cisco CallManager Service Parameters when a service is selected (CM, Attendant Console, etc.). Has anyone seen this before?
Yes, the CM was setup by another vendor and has been running for a while. We will probably schedule a reboot, but I wanted to be sure there wasn't something else I could look at first.
-
Cisco CallManager Installation
As new in Voice Networks, I have a question ! Is Cisco CallManager Solution must be installed on designated / cisco recomended hardware. I want to try it before going a head with buying stuff. Can i install it on my server machines with Windows 2000 Server ??
If any one was successfull please let me know.
thanks,
ShakeelThis is how to get CallManager 4.1.3 running on non-MCS server.
1. Install Windows 2000 server (15 gig partition). Make all passwords the same, including WIN2K account. (I used " cisco" )
2. Keep all the default installation components,
just add DHCP under Network Services,
and SNMP under Management and Monitoring tools.
3. Assign a static IP.
4. If installing in VMware, install VMware tools (under the main VM tab ) .
5. Install SP3 (at-least). (or make an win200 boot CD yourself with slipstream( google: XP slipstream)
6. Setup DHCP scope and options, don't forget to add the CISCO TFTP option 150
7. Copy the text below into a text file and name it with a .reg extension,
double click this file to make the changes to the registry.
7a) ccmreg1.reg
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SOFTWARE\Cisco Systems\Model]
"Hardware"="MCS7825H02"
"Speed"="2268"
"Memory"="2048"
[HKEY_LOCAL_MACHINE\SOFTWARE\Spirian\System Info\OS Image]
"Version"="2000.2.6"
[HKEY_LOCAL_MACHINE\SOFTWARE\Spirian\System Info\OS Service Release]
"Version"="2000.2.6sr5"
7b) install win-OS-Upgrade-K9.2000-2-7.exe
7c) ccmreg2.reg
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SOFTWARE\Cisco Systems\Model]
"Hardware"="MCS7825H02"
"Speed"="2268"
"Memory"="2048"
[HKEY_LOCAL_MACHINE\SOFTWARE\Cisco Systems\Spirian]
"ProductKey"="BTOOVQESCCJUIEBI"
"Deployed"="0000000000000000"
8. copy c:\program\cisco\updates\2000 2.7sr5\shutdown.exe naar c:\utils
9. Install CallManager 4.1(3)
ccmsetup.exe
10. Go to Start >> Programs >> CCM 4 >> CallManager Administration and IE will open.
11. Go To Menu >> Application >> CCM Serviceability >> Tools >> Service Activation.
>>Click> on server u want to configure on left hand side.
>>Click> "Cisco RIS Data Collector" and press update.
>>Click> on all the services one by one and press update.
12. You should now have CallManager 4.1(3) running.
13. Upgrade OS and CCM with all patches if needed.
14 you can use P2V to make an copy of an working CM to a VMware machine -
Maintaining the Directory in Cisco CallManager Attendant console
I have names in the directory of the cisco callmanager attendant console users that no longer work for the company. The numbers and names have been deleted from the call manager but not the directory used by the attendant console. How do I go about cleaning up the directory for the attendant console?
Hi,
Thanks for the doc..4* for the info.
This basically explains what I've checked already. Cynth, seeing as you've checked on the AC PC that there's no userlists file, and we now know you have 2 files present on the callmanager I would suggest the following to resolve your problem:
1) Delete both the AutoGenerated.txt and CorporateDirectory.txt from the CallManager Attendant Console directory (I've put the path in my previous post). You can copy them off this directory if you want a copy for keep safe.
2) Re-start the TCD service again.
3) Shut down the AC client and re-open it.
This should basically re-populate the directory on the CallManager (once you re-start the service). Then when you open up AC again it should copy across the up-to-date corporate directory list.
Please rate useful posts... -
Cisco Callmanager Amtskopfanzeige
Hallo zusammen
wir haben ein kleines Problem in unserer Telefonanlage und zwar...
Bei ankommenden Anrufen per Handy werden ja 2 Nullen von der Telefonanlage vorne angehängt.
Wenn jetzt Handys mit Amtskopfanzeige (Rufnummer Anzeige bei Weiterleitung – Telekom option) auf einem Telefon(mit Weiterleitung auf Handy) anrufen, werden diese 2 Nullen noch angehängt.
Siehe hier:
0151xxxxx -> 089xxxxxxx (Weiterleitung -> 0175xxxxx) = +49 (0) 0175xxxxxx (am Handy)
Somit wird die Nummer falsch angezeigt und kann auch nicht zurück gerufen werden.
Cisco Callmanager
System version: 6.0.1.2000-3
Habe auch schon ein paar Sachen in den Routepattern probiert aber ich komme irgendwie nicht weiter.
Vielen Dank und Gruß
HaraldYes, the CM was setup by another vendor and has been running for a while. We will probably schedule a reboot, but I wanted to be sure there wasn't something else I could look at first.
-
Speed dial migration of each phone from cisco callmanager 4.1 to cisco callmanager 7.1
Can anyone enlighten me how to backup all the speed dial list of each phone from 4.1 callmanager to 7.1 callmanager ?
Hi Alan,
The only other way that I can think of would be to use a BAT Export from 4.x
and then BAT Import into 7.x. The header fields won't match exactly between
the old/new versions of BAT, so some re-jigging will be required
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/bat/5_0_4/t03phexp.html
Cheers!
Rob -
Cisco unified Operation Manager 2.3 with CUCM 8.6
Hi Guys,
My Customer today have CUOM 2.3 and CUCM 7.1.3. He is planning to do upgrade CUOM 8.6 and CUCM 8.6. My question is: Is it possible to do upgrade CUOM directly to 8.6? If CUOM to be upgraded to 8.X do we need to purchase the upgrade license?
Thanks,
WilsonI don't think you can install on top of CUOM 2.3, a CUOM 8.X. Not even a 8.0
As said, you can restore a CUOM 2.3 backup on an 8.X.
http://www.cisco.com/en/US/docs/net_mgmt/cisco_unified_operations_manager/8.5/installation/guide/install.html#wp1054045
As far as I can see after CUOM 8.5 the 2.3 migration path is no longer mentioned.
Cheers,
Michel
Maybe you are looking for
-
How do you filter out moving objects in a movie?
Hello! I'v searched the internet for solutions to this but I cann't find any. Im prittie new and I need to make a house on fire while two guys (one is me) will be walking away from it, towards the camera. I want to filter out these two guys and only
-
Says browser not working and said to update ?
updated to ios 6 but website I went to wouldn't open said something about had. etscape and need to update
-
Hi gurus, its urgent, pls help me. i have to create a report on bw statistics (i know the procedure and using bw statistic standard reports also) i have to find out 1. Inactive users (Never Access the system). 2. Reports that failed 3. Cube Sizes,
-
Error Code 6 when downloading Adobe products
Exit Code: 6 Please see specific errors below for troubleshooting. For example, ERROR: -------------------------------------- Summary -------------------------------------- - 0 fatal error(s), 2 error(s) ----------- Payload: Microsoft Visual C++ 2012
-
White or black -- heat issues when in the sun??
I have a black 4s now and I'm deciding between the white and black 5S later this month. I tend to use my phone as my GPS and have a window mount that holds the phone up for me. However, this means that the back of the phone is frequently in direct s