Cisco CCX support for TTY/TDD

All;
I need to deploy a CCX 9x solution that supports TTY/TDD. I can find documents that describe our phone asscessability and how to connect a device to a FXS port. but I cannot find anything that says a hearing imparied person can communicate with CCX. How does CCX support a TTY/TDD device? The only thing I found is web chat through social miner.
thanks
tony

The MIVR engine in CCX does not support TTY/TDD devices directly. The caller would need to invoke a relay operator as they would with any other voice-only call. Once the call is transferred to an agent they could conceviably use a TTY/TDD coupler-style device to communicate with the caller. The agent cannot use a straight FXS-driven device since the ICD subsystem can perform CTI control/observation on supported Cisco IP Phones.
Please remember to rate helpful responses and identify helpful or correct answers.

Similar Messages

Cisco ASA support for PBR

Does anyone know if Cisco has the PBR feature road mapped for future IOS releases or if they are building in new feature sets to load balance 2 different ISP connections much like F5. It seems more and more customers are asking for all in one functionality from their NextGen firewalls and the ASA seems to fall short in this category.

As of right now, you can do PBR on the ASA when the ASA is in a cluster. I am uncertain if there will be support for PBR or loadbalancing on a standalone ASA in the future.
http://www.cisco.com/c/en/us/td/docs/security/asa/asa90/configuration/guide/asa_90_cli_config/ha_cluster.html#pgfId-1943033
Please remember to select a correct answer and rate helpful posts

Can Cisco 7200VXR support for VPLS?

Hi all,
I check Cisco Nagivator Feature to find which IOS support for VPLS on Cisco Router 7200VXR and found that IOS image "c7200-spservicesk9-mz.122-33.SRD.bin" can do it as below;
- VPLS Autodiscovery, BGP-based
- VPLS Multiple VCs per Spoke
When I try to configure Virtual Forwarding Instance, it's not allow me to configure the above features (VPLS Autodiscovery: BGP Based, Manual Configuration of VPLS) and only support point-to-point configuration mode you can see it as below
R1#show version
Cisco IOS Software, 7200 Software (C7200-SPSERVICESK9-M), Version 12.2(33)SRD, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Thu 23-Oct-08 12:58 by prod_rel_team
R1(config)#l2 vfi ?
WORD VFI name
R1(config)#l2 vfi VPLS_A ?
point-to-point Point-to-point configuration mode
R1(config)#l2 vfi VPLS_A point-to-point ?
<cr>
R1(config)#router bgp 100
R1(config-router)#bgp router-id 150.1.1.1
R1(config-router)#neighbor 150.1.12.2 remote-as 100
R1(config-router)#neighbor 150.1.12.2 update-source lo0
R1(config-router)#address-family ?
ipv4 Address family
ipv6 Address family
l2vpn Address family
nsap Address family
vpnv4 Address family
vpnv6 Address family
R1(config-router)#address-family l2vpn ?
vpls Address Family modifier
<cr>
R1(config-router)#address-family l2vpn vpls ?
<cr>
R1(config-router)#address-family l2vpn vpls
% BGP: Error initializing topology
R1(config-router)#
I can use "l2 vfi VPLS_A point-to-point" for Layer 2 VPN Pseudo-Wire Switching but not for VPLS multipoint configuration mode. Can Cisco 7200VXR support VPLS on this IOS image? If it can't, which IOS image can do it on this platform.

VPLS is not supported on 7200, you can configure point to point here but not point to multipoint, you will have to move to 7600 for that.

Does Cisco NAC support for HP Switches

Dear all,
the existing network has HP switches , is there any way i can deploy Cisco NAC solution here ?
Pls revert .
thanks ,

Cisco NAC has lots of limitations, and surly this is one of them. But while I respect the fact that cisco will not support NAC on HP switches. It can work. And it will perform just fine, once you understand “Cisco NAC” and able to configure it for the first time, you will be able to support it without the need of TAC.
The idea is that Cisco NAC sends commands to the switches on the network to apply specific access list or Vlan changes, since Cisco can only speak Cisco, it does not know how to tell other switches to do that. . The work around is that you would have the NAC running in in-line mode on your network, yes this will introduce a bottleneck, but that is the only way to do it. The NAC then will look at the traffic based on the MAC or IP and apply set of policies depending on the source or the destinations.
Please do your research and look at other NAC solutions before you decide the best vendor to go with.

Cisco 8841 support for 3rd party call control

Hi Cisco Team,
What is required to get Cisco 8841 IP phone configured as a SIP phone for 3rd party call control?

Hi,
This information would be dependent on which third party you are integrating with, they should provide details of settings needed for the same. For supporting third party SIP endpoints with Cisco there are numerous docs / posts , but in your case the scenario is reverse.
HTH
Manish

Cisco 4500x Support for USB

Hi,
Does the catalyst 4500x support any usb drive or does it need to be specific cisco
USB-X45-4GB-E
Cisco Catalyst 4500 4-GB USB
I have tried a generic one. Copy works but wireshark capture to usb0 fails.
Could it be that switch supports only cisco specific usb drive.
Thanks

Can anyone from Cisco confirm this?

TTY Support for Phone

hi,
does anybody know what the TTY support for BB phone is?
its listed under applications that you can in/uninstall to and from your device in blackberry desktop software. what is the TTY for, what does it do?
Solved!
Go to Solution.

An alternative name for a telecommunications device for the deaf (TDD)
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Android tablets supported for Cisco Jabber for Android 10.5 ?

Exist a list with tablets support for this realease ?
In release notes only include smartphones.
Anoher question, is about version android client, in google play exits a old version, but not 10.5, any reason for this ?
Thanks in advance.

The tab listed for support is " Google Nexus 10 (Android OS 4.4.x) ". Please refer to the following link for more information;
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/jabber/10_5/CJAB_BK_D6497E98_00_deployment-installation-guide-ciscojabber/CJAB_BK_D6497E98_00_deployment-installation-guide-ciscojabber_chapter_011.html#CJAB_RF_D3CF90B1_00
Quoting the following link; https://play.google.com/store/apps/details?id=com.cisco.im&hl=en ;we have got the J4A 10.5 listed on the playstore.
- please rate if this helps.

What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP's?

What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP’s?

• PI provides visibility for autonomous clients within the same list view as lightweight and wired clients (client list page).
• Rogue AP detection for autonomous AP's is not supported (it's supported in CUWN).
• Alarms/events for client authentication issues (e.g. authentication failure) are displayed in PI.
• Config management for autonomous AP's is via CLI template. Config comparison and archiving functionality in PI leverages these same features that were brought in from LMS, so need to defer to others in terms of whether this is a cross-platform feature in PI or is only supported on a subset of platforms. Config comparison/archive is supported in CUWN.PI supports both infrastructure (e.g. AP Tx Power and Channel, busiest AP, AP utilization, etc.) and client (e.g. client count, client sessions, etc.) reports, and there are extensive reports for CUWN

I want to integrate SMS gateway to Cisco ISE 1.2 and my question is SMS notifications are supported for Guest self−registration

I want to integrate SMS gateway to Cisco ISE 1.2 and my question is
SMS notifications are supported for Guest self−registration Services ? or it should be done by Sponsor

I'm not sure I understand the question. Do you want to log in to the Sponsor Portal using AD credentials?
Create an Identity Source Sequence using AD as an Authentication Source. Go to Administration > Identity Management > Identity Source Sequences. Either Edit or +Add a Sequence and choose from the Authentication Sources shown.
Then choose that Identity Source Sequence by going to Administration > Web Portal Management > Settings. Double-click Sponsor from the Left Menu and click Authentication Source. Choose the Identity Source Sequence. Click Save.
I hope this helps.
Please Rate Helpful posts and mark this question as answered if, in fact, this does answer your question. Otherwise, feel free to post follow-up questions.
Charles Moreton

What to support for Cisco IP Phone 7912?

dear all. please help me!!!
I have a 7912 ip phone, and using Cisco CME in 1760, but I do not see this type 7912 ip phone telephony service there. whether it was true ip 7912 phone is not support for the Cisco 1760 CME. and whether support for the cisco 7912 ip phone? whether the telephony-service configuration is equal to the telephony-service configuration for the ip phone 7940?
please help me !!!

Hi to all
Please I ned some advice , I was try to reset to factory defaults a Cisco IP Phone 7912 and I was failed .
Please can you help me ?
Thanks a lot !
Hugo Baez

Cisco Prime LMS 4.1 - Support for Cisco Catalyst 3560-C Series Switches

Hello together
I have a customer which uses the following switch. Last year I have installed LMS 4.1 for him to manage the switches. Unfortunatly the switch model is not supported. According to the information found on the following site the switch is supported for most of the modules in LMS:
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.1/device_support/table/lms41sdt.html
The oid object of the device is the following: 1.3.6.1.4.1.9.1.1465
Supported Software: 12.2(55)EX (Customer has 12.2(55)EX3
Version Support Type: Device Update
So I updated all device updates I was able to find.
Step 1: For that I went to Admin > System > Software Center > Schedule Device Downloads and created a job where I have downloaded the latest versions of all packages.
Step 2: Installed the downloaded packages Admin > System > Software Center > Device Update and installed all the packages.
Unfortunatly I don't see the same result like described in the Supported Device Table for LMS 4.1.
- Cisco View -> works
- Inventory and Config Collection -> works
- Fault Monitor not working -> Error Code Unsupported
- Network Topology Layer 2 Services -> Device Type ciscoProducts.1465, Symbol Question Mark
- VLAN Management -> Doesn't work
- User Tracking > seems also not to work
When I open the report for supported devcies (Reports > System > Device Support) and search for C3560C... I find the following devices, but not mine which i need:
C3560C-8PC-S     .1.3.6.1.4.1.9.1.1466
C3560CG8PC         .1.3.6.1.4.1.9.1.1317
C3560CCG8TC     .1.3.6.1.4.1.9.1.1318
wsC3560CPD8ptS     .1.3.6.1.4.1.9.1.1368
Does anybody have experience with the same switch type / model? Am I doing something wrong or is this type of switch not implemented correctly till now? Further the docuemntation supported devices would be wrong.
Thanks for any feedback Erich

Thanks but I just heard back from my Cisco SE and he assures me that an AP will NOT use up a license.
I've asked him to verify his answer for me.
Is your answer based on real world expereince (the best there is)? That is, are you running Prime LMS 4.1 and does it indeed use up a license for each light-weight AP it discovers & manages?
Thanks for mentioning options 1-3 but I do not wish to employ any of them. I don't mind buying the additional licenses for APs ... I just need to know if I have to or not.
Ian.

Can cisco router support OSPF-TE and ISIS-TE same time for CSPF to compute a TE LSP? I may need to run both IGP in parreral.

Can cisco router support OSPF-TE and ISIS-TE same time for CSPF to compute a TE LSP? I may need to run both IGP in parreral.

hello - I have just moved your post to the Topic forums - you had posted your question in an obscure non-visible promotional community Hopefully our community users will see your question now.

Can cisco router support OSPF-TE and ISIS-TE same time for CSPF to compute a TE LSP? I may need to run both IGP in parallel

Can cisco router support OSPF-TE and ISIS-TE same time for CSPF to compute a TE LSP? I may need to run both IGP in parallel.

Hi Johnny,
Per my understanding you can. It is equivalent to running 2 IGP and installing the entry in RIB table based on administrative distance.
-Nagendra

Are the SG500P SMB switchs supported for Cisco Network Assistant?

Hi, we need to enroll some SG500-28P switches to a CNA? Is this possible? I suppose that CDP feature allow this. Actually, i have installed CNA Ver. 6.0. Thanks in advance.

Hello Fernando,
Thank you for visiting the Cisco Support Community!
Here is a list of all the devices supported by the Cisco Network Assistant for the 6.0 version and later. Many of the 500 series switches, including the SG500-28P Managed Switch, are supported by the CNA. This page will also give you any additional information you may need such as the features of the CNA 6.0 version, any system requirements, and more.
If this post was helpful, please remember to mark this question as resolved to help others in the community! If you have any further questions, please do not hesitate to ask!
Best,
LP

Cisco CCX support for TTY/TDD

Similar Messages

Maybe you are looking for