Cisco commonservices upgrade query

Hi All ,
I am running with cisco common services 3.1 version . I want to upgrade the same to 3.2 .
Please guide me  from where can i download the Software in cisco site
Thanks in Advance
Regards
Angus

Hi Angus,
You can download LMS 3.2 from www.cisco.com\go\lms
At the bottom of the page, Under the Featured Contents , click on Evaluate LMS Solutions > on the next page click on --> Network Management Evaluation Products .
There you will find :-
CiscoWorks LAN Management Solution (WINDOWS OS) 3.2
CiscoWorks LAN Management Solution (SOLARIS OS) 3.2
License of LMS 3.1 will be valid for LMS 3.2 as well. Though its evaluation version but its complete setup, so if  you will run the setup on top of LMS 3.1, this will installed LMS 3.2 as complete setup and license version.
LMS 3.2 Install Guide :-
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/install/guide1/lmsigsg.html
Here are the Tips for successfull LMS installation pen by Joseph Clarke :-
https://supportforums.cisco.com/docs/DOC-9132
Note :- Its good to take the backup of CiscoWorks LMS 3.1 before doing any upgrade.
Many Thanks,
Gaganjeet

Similar Messages

  • UCS B200M2 Version 2.1(1d) to 2.2(1d) upgrade Query

    Hi,
    I am planning to upgrade our UCS B-Series server(B200M2) to 2.2(1d) from 2.1(1d).
    While i was reading the Cisco document for the upgrade, they were specifying about a bug CSCuh61202 ( https://tools.cisco.com/bugsearch/bug/CSCuh61202 ) .It is saying that "If you are upgrading from a release prior to 2.1(3a) or 2.2(1b), you may be impacted by CSCuh61202.".
    But while i am reading about the bug, it that it is saying that the affected version is 2.1(2a)A.
    So my question is, should i bother about this bug ,since my current version is 2.1(1d). ????

    Hi friend,
    in our environment also, its full of cisco devices and mostly all devices were affected by this shellshock bash vulnerability. i contacted cisco TAC for querying about all those devices we implemented but since each TAC engineer are specialized on a specific domain...they were unable to answer all. Other wise i need to raise separate TAC for each devices. when i checked their releases before few days, they said that there is no work around at the device side. They asked to harden the firewall and IPS. Actually they released IPS signature to prevent the shellshock attack.
    Also you should upgrade both infrastructure and server firmware. Both firmwares should be of same version.
    I recommend you to open a TAC request and keep the engineer on hold while you performing the upgrade process.

  • Cisco MARS Upgrade available - 4.2.3

    Cisco MARS upgrade has been posted to Cisco's web site. It is a large upgrade and has special instructions.
    I did not see any notes for support of Cisco IPS 6.0 new fields.
    Web Site
    http://www.cisco.com/cgi-bin/tablebuild.pl/cs-mars

    thanks for the post! holy crap, you weren't kidding...>1GB???

  • Cisco ASA Upgrade from 7.0(8) to 8.2(1)

    Hi,   i need to upgrade my 5510 ASA from 7.0(8) to 8.2(1)       ( Please note its different query from my last thread)
    what i found online is i will have to do this upgrade in sequence, that is
    7.0.x -> 7.2.x --> 8.0.x --> 8.2.1
    is that correct?
    or i will go to 7.1.x first? like this
    7.0.x--> 7.1.x -> 7.2.x --> 8.0.x --> 8.1.x--> 8.2.1
    Please guide, Also i am assuming, reboot required after every upgrade right?

    ok, i found something on another Cisco document. that is what i thought
    To ensure that your configuration updates  correctly, you must upgrade to each major release in turn. Therefore, to  upgrade from Version 7.0 to Version 8.2, first upgrade from 7.0 to 7.1,  then from 7.1 to 7.2, and finally from Version 7.2 to Version 8.2 (8.1  was only available on the ASA 5580). "

  • Cisco ise upgrading and licences

    I nedd to upgrade from version 1.1.2 patch 4 to 1.1.3
    the deployment is distributed so the split deployment technique needs to be used:
    http://www.cisco.com/en/US/docs/security/ise/1.1.1/upgrade_guide/upg_dis_dep.html#wp1052969
    the guide is quite hard to follow as there are some licensing informations missing that can potentially cause service downs:
    in particular my questions reguarding the guide are:
    --- OUR licence is registered to the primary PAN node only----
    1) Deregistering primary PSN "D" node : what licence it will use? the inherited (10000 endpoints) or will it lose the licence completely and lock the network authentications?
    2) When node "B" will be deregistered and will become standalone what happens to its licence ? will it be lost? and what will happen to the node "D" when added back to the node "B" ?
    3) when I will switch back node "A" (after upgrade and registration to node "B") to its previous primary PAN state it is stated that the licence needs to be reloaded in it cause it was lost when adding it to node "B".... and in the meanwhile? no node will authenticate cause the primary node is without a licence?
    TY

    Giuliano,
    De-registered node will always use it's own license, i.e. it becomes standalone box without knowledge or information of anything around it. Either the evalutaion or whichever license you have supplied it with.
    License enforcement is performed by active admin node in cluster, according to its license.
    Have a look at:
    http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCug04405
    I don't think license needs to be reloaded, but that may be just my memory not serving me. I'll double-check that one.
    M.

  • How often does cisco do upgrades to their kickstart and OS? Is there a bulletin date or some kind of notification?

    I am starting to work with Cisco Switches, I have 12 Nexus 6000 series and 2 Nexus 7000 series (core switches) I just upgraded to kickstart 7.1(0)N1(1). and OS 7.1(0)N1(1)......However I want to know if there is a specific date or dates that Cisco releases new upgrades so I can be prepare. Can someone help me with this? Thank you so much.

    Not that I know of, however it's not a bad suggestion. I'd recommend posting to www.apple.com/feedback. Don't expect to hear back though.

  • Cisco UC520 Upgrade

    Hi,
    i have a UC520، and it show the below error:
    "Oct  6 09:47:31.695: %SCHED-2-EDISMSCRIT: Critical/high priority process VTSP may not dismiss. -Process= "VTSP", ipl= 0, pid= 236,  -Traceback= 0x80E728F8 0x8209D2D8 0x80E5ACA0 0x80E8BFD0 0x80E8A9E8 0x80E8BAF0 0x8213A018 0x8213A278 0x8213A628 0x8213131C 0x82132600 0x80B47F24 0x80851530 0x80859A04 0x82DB8848 0x82DB8FB0"
    And i was read the error related to bug, and the upgrade is the solution of this bug, so we will go into upgrade, does i need to upgrade the whole package like below link :
    https://supportforums.cisco.com/docs/DOC-10315
    or i can just upgrade the IOS? and if i will upgrade the IOS deos it affect the system Cisco Unity Express.
    The Second question,if i need to upgrade the whole package,  does the upgrade need license?
    the Licence on my UC500 like below:
    sh license feature
    Feature name             Enforcement  Evaluation  Clear Allowed  Enabled
    uc500-16u-upgrade        yes          yes         no             no  
    uc500-32u-upgrade        yes          yes         no             no  
    uc500-24u-to-48u-upgrade yes          yes         no             no  
    uc500-48u-upgrade        yes          yes         no             no  
    uc500-48u-to-64u-upgrade yes          yes         no             no  
    sh platform software license
    Upgrade license              : uc500-48u-to-64u-upgrade
    License status               : Not in Use
    License UDI                  : UC520-48U-T/E/F-K9:FHK1350F06G
    Maximum User Licenses        : 56
    Used User Licenses           : 38
    Available User Licenses      : 18

    So if i upgrade to the "uc500-advipservicesk9-mz.151-4.M6" IOS this will upgrade the CME, and it may solve this Error.
    but if i will upgrade the whole UC500 does this require license?

  • Cisco IRONPORT UPGRADE keep failed

    Hi all,
    I try to upgrade one of the ironport s170 version 7.1.3-031, but it keep failed.. and the upgrade process very slow. Any idea??

    Hey Vince,
    I was actually trying to get your view of what seems to be the issue and I highlighted the ETA because that was a big number.
    I would recommend you to start fresh. Reboot the box, and try the upgrade again. The reboot would clean the temporaty files if any could be interfering.
    Try the upgrade from the CLI and choose the most recent version of AsyncOS available.
    Upgrade issues are usually but not always related to bandwidth control, proxy, network latency, file system corruption. A packet capture could help to identify proxy limiting and some other network related issues but you can also try Local Upgrade.
    How do I get a packet capture (tcpdump) from a Web Security Appliance or a Email Security Appliance?
    Knowledge Base Answer ID: 628
    http://tools.cisco.com/squish/Ae538
    Comprehensive Guide to Local Upgrade Servers
    Knowledge Base Answer ID: 1558 
    http://tools.cisco.com/squish/212fd
    From the screenshot also, we cannot get the current version you have running but I am guessing it is an old version. Another reason to support the upgrade. It is possible your appliance is not listed as authorised to get upgrades. If you cannot upgrade using Local Upgrade process described in the article above, you should definitively open a support ticket so the engineers can check the appliance's status and assist you further.
    I hope this helps.
    Regards,
    -V

  • Cisco EA4500 Upgrade causes ipad (1) issues especially with netflex

    I just upgraded Routers to a Cisco EA4500 (N900) router.  Now Netflix will stop every 30-40 seconds to buffer.  Speed test on ipad shows 7MB+ every time I have tested...  Any ideas?

    are you still haveing this issue if you use the old router?

  • 74 upgrade: query properties field: Operation in BWA/HANA

    Dear all,
    once we upgraded to BW 74 SP09 we experience some issues regarding query properties. In particular some queries are not having same value of field "Operation in BWA/HANA = RSRREPDIR-TREXOPS".
    The value of the field in RSRT is different comparing to table. As example query has setting set to "6=exception aggregation (default)" however the corresponding field in the table is blank. My consumption was that all the queries after the upgrade should be set to value "2=Individual access per IProv".
    I expected this as per SAP Note "1790426 - Processing MultiProviders in BWA" which saying about official SAP recommendation value of the field.
    My questions:
    1. Anyone experiencing same inconsistency between table and RSRT value?
    2. What is than really recommended value? E.g. in BW74 SP09 the option 6 has a word "default" in brackets.. but above mentioned Note says differently...
    PS: our BWA version is 7.20.32.00
    Thanks,
    martin

    This is a Duplicate Post. [url https://forums.oracle.com/forums/thread.jspa?threadID=2401881&tstart=0]Original Post Can be found here.

  • ACS Upgrade query

    Hi
      I have upgraded ACS solution engine from 4.2.0 to 4.2.1 successfully.I have upgraded ACS software and appliance mangement software.Should i upgrade base image also?.I didnt find base image in the cisco download session of ACS
    Thanks in advance
    Anvar

    Hi Anvar,
    You dont need to upgrade the base image as the most current i guess is 4.2.0
    Thanks
    Waris Hussain.

  • N79 firmware upgrade query.

    Hi. I'm probably one of the few who have this troublesome phone, and, not wanting to brag, I'm on my 2nd one which is working absolutely fine with no problems at all!
    My query is though, should I upgrade to the V.20 firmware when it becomes availiable or keep things as they are?
    I only ask because it seems that many who upgraded to v.20 have been plagued with new minor issues which I'd like to avoid if poss.
    Be greatful for any thoughts on the matter.
    Jurassic Park, Sam Neill to Dickie Attenborough " Mr. Hammond, the phones are working !"
    N8-00 Tesco UK 059C951, Lumia 920

    If you are happy with your phone the way it is then that is a good reason not to rock the boat. Firmware update is risky business.
    Updates usually only contain bug fixes and sometimes a  new feature or two. They sometimes also remove features. What you could do is to check the Changelog for the update andsee if there are any bug fixes or new features in the update that will make a difference to you. Changelogs are not published by Nokia but usually available on other sites so just google for it.
    However, if you are like me and have to have the latest of everything then update with your fingers crossed.

  • Technical Upgrade Query Issue .

    Dear ,
    We are updating our system from ECC4.7 to ECC 6.0 .
    I come across the issue that Queries are not updated in system .
    Some of the queries I have resolved by going in transaction SQ01 simply by acivating it and execute but in some of the
    objects query name does not exist in old system but report execute there .
    In new system 6.0 this not even executing . What the problem that not able to identified .
    For example :
    Query is this  :  AQFKSYSTQV000015ZPODET======== 
    Query name is : ZPODET
    This is not exist in both the system but its running fine in old system .
    Please suggest any solution for this if u have any .
    Rgds Aryan
    Edited by: Aryan@sap on Nov 11, 2009 10:59 AM

    Hi,
    This is the most common issue faced during the Upgrades.
    1) First go to SE37 and execute the FM: RSAQ_GENERATE_PROGRAM by entering the Query name and the User group.
    2) You can get the link for SAP Query and User groups from the table AQLQCAT(local areas) and AQGQCAT(global areas)
    3) Finally after the query is generated, you will get the program name as output of the FM.
    4) Check this program exists in SE38.
    If you want to generate more queries try writing a simple report using the above logic....
    OR Simply go to SQ01 and try to generate each query from the menu->Query>More Functions->Generate Program
    The same process needs to be done in all the systems(old/new/dev/quality/prod systems)
    For your help, AQFKSYSTQV000015ZPODET======== the name of query and user group can be determined as:
    First 4 char : system specific
    Next 12 Char : User Group
    Next 12 Char : Query name.
    Wherever names are less than 12 chars then the = are added.
    Hope this helps
    Regards
    Shiva

  • RedHat Enterprise Cluster and Cisco IGMP Snooping/Querying

    Has anyone else had any experience with IGMP Snooping/Querying and RedHat Enterprise Cluster?
    We have been experiencing a large amount of problems with this functionality.
    We are running IGMP Querying in our environment and we recently set up a second querier.
    Here's the steps we took
    Existing querier:  192.168.3.248
    Everything was running fine.
    Added a new querier on a different switch: 192.168.3.247
    At this point, all of our RedHat Enterprise Clusters fenced themselves and needed to be restarted in order to restore
    access.  In order to restart the RedHat Enterprise Clusters, the physical servers must be rebooted.
    Are there any known issues with RedHat Enterprise Clustering and Cisco Switches (3750
    series)?  I would expect the querier change to be seamless, but it does not seem that this
    is the case. 

    Hi,
    In our organizaiton we have Red Hat Cluster with 2 cisco switch (Model: cisco WS-C2960S-24TD-L, Version: "flash:/ c2960s-universalk9-mz.122-55.SE3/c2960s-universalk9-mz.122-55.SE3.bin").
    - We are using HP Chassis c7000 and Server is on the chassis. There are 2 service IC & Med. Each server has one service primary and other secondary running.
    - The two cluster switches are connected each other with Ether channer trunk (1+1) link. Also these 2 switches are connected to our Mgmt switch for Server Admin access to HP Chassis via OA port. The Red Hat system has cluster lan (pri & sec) & OA lan (01 & 02 of HP chassis) connected to Cluster switches. The Mgmt VLAN is 501 - 172.31.10.0/24.
    Problem:
    When the CluserSW01 goes down the cluser shifted to CluseterSW02 with Cluser_Secondary_LAN and OA2. But when the ClusterSW01 switch comes again than the communication breaks and cluster don come up.
    I was thinking this is either STP or IGMP, well sure though. As these are production systems hence we also couldn't do much more test as well.
    If you have face any such issue or have experience with it or know what the problem might be... kindly share with me.
    Thanks,
    Adnan

  • Cisco Prime upgrade (Standard to Pro)

    Hello
    Can anyone help answer a query we have regarding an upgrade we need to do on Prime Infrastructure, PI.
    We are running PI version 1.3 on VMware in a standard deployment.
    We want to upgrade to a Pro deployment.
    My understanding is that the only difference between standard and Pro, is that additional VMware resources are needed.
    On the software download site, there is a separate OVA image for Pro, however there is also a Prime 2.1 upgrade installer image.
    Can an existing VMware Prime be upgraded to Pro by increasing the VMware resources and running the upgrade image or does it need a clean install
    Thanks
    Martyn

    You can do a restore on the new VM if you want. I typically have not and I would export the maps from the old version, add the WLC's to the new PI and then import the maps. You can then repost licenses if your running PI 2.1 or earlier. PI 2.2 will take your original license from PI 2.0 & PI 2.1.  You would just need to download the license again or open a TAC case to obtain them. 
    -Scott

Maybe you are looking for