Cisco Configuration Professional - Monitor - Traffic Status - Application traffic view
Installed the Latest version of CCP. Noticed that it use Internet Explorer as the default browser.
Current issue - Monitor - Traffic Status - Application traffic view show a window that is to large for my current screen,
I've tried several options to make it more viewable, but no luck.
Screenshot, Explaining the issue - Notice the difficulty to view the graphs
Any advice will be appreciated.
Philip
I've manage to fix it by changing the zoom on Internet Explorer
Similar Messages
-
ISM-SRE-300-K9 & Cisco Configuration Professional Issue
hi there,
i have a cisco 2901 router running CME 8.6 the router has a ISM-SRE-300-K9 card init with Unity Express 8.0.5 installed.
i am having issues with Cisco configuration professional and configuring the module
under module configuration the status is "module is not reachable", if i click on details i get further information "unable to execute command from the module. module is either reloading or is in failed state. you must make the module up and refresh the module"
i have tried reloading, resetting and refreshing the module but the issue is still present
i have accessed the module from the CLI set it in offline mode and factory defaulted it and the same issue is still present
the only thing i can think is that this is a bug with CCP as the loopback interface which the module is using can be pinged fine from the router so the message makes no sense.
any ideasIs you problem with CCP or the module itself ?
Because, CCP bugs and limitations aside, the module can be normally be installed, configured and managed using CLI or its web interface (after software is initially loaded). -
Can't launch Cisco Configuration Professional on Windows Vista x64
The Help is necessary to resole the issue (see subject).
Tech enveronment
Windows Vista x64
Adobe Reader X ver. 10.1.0 (Russian)
Cisco Configuration Professional 2.5
JRE 6 update 27
JRE 6 update 27 (64-bit)
Internet Explorer 9.0.8112.16421IS
While launch CCP popup the message box :
"Unable to read the resource file. The file could be corrupted. Please re-install Cisco Configuration Professional to resolve the issue."
Ones (never popup after) Popup the message box (InstallShield Wizard):
Adode Reader is not present on the PC. It is required to view the PDF file.
Also the message box InstallShield Wizard:
Internet Explorer with javaplug-in version 1.6.0_11 Cheked
Adobe Flash Player version 10 Cheked
Memory 1 Gb Cheked
Screen Resolution 1024x768 Cheked
Cuted _cpinstaller_004.log file:
Product : Cisco Configuration Professional version 1.0
10-4-2011 16:48:31 LOG : Command line options =
10-4-2011 16:48:31 LOG : GetOS: OS Windows Vista
10-4-2011 16:48:31 LOG : GetOSServicePack: service pack 2
10-4-2011 16:48:31 LOG : GetIEVersion: IE version 9.0.8112.16421
10-4-2011 16:52:51 LOG : CheckCCPPorts: WARNING 80 is not a registered HTTP port
10-4-2011 16:53:27 ERROR : SetRunAsAdmin: ERROR REG_APP_COMBAT_LAYERS_ROOT could not be created.
10-4-2011 16:53:46 LOG : GetJavaIEPluginVersion: java IE plugin version 1.6.0_27
10-4-2011 16:53:47 LOG : GetFlashPlayerVersion: flash player version 10
10-4-2011 16:53:47 LOG : GetScreenResolution: screen resolution 8
10-4-2011 16:54:14 LOG : OpenPDFFile: Adobe reader could not be found on system.
10-4-2011 16:56:17 LOG : OnEnd: installation successfully completed.Hi,ngoldwat!
Yes, off cource, I've tried to launch CCP with Administartor rights - no success.
I have re-installed CCP under Local Admin and launched it. Great!!! It works! But, one of but, the app does not launch from domain user while I use Run as Administrator. I think the issue in the permission and/or user's profile.
Thanks ngoldwat! You have helped me. -
Setting up Easy VPN in Cisco Configuration Professional, external access problems!
Hi
I have a Cisco 857 router which is flashed with Cisco Configuration Express 2.6.
Cisco Configuration Professional 2.6 is installed on my PC and I'm trying to configure Easy VPN for access away from the office.
The steps I have taken are as follows:
1) I launched the Easy VPN Server Wizard
2) IP address of Virtual Tunnel Interface is unnumbered to Vlan1 from the drop down menu - Authentication, Pre Shared Key
3) IKE Proposals set to the default option thats already there
4) Transform set is the default which is already there
5) Method list for group policy Lookup is LOCAL
6) User authentication is LOCAL ONLY, the admin account shows up in ADD USER CREDENTIALS which is the account i'm going to test the connection with
7) I have set up a GROUP POLICY which i've named, created a PRE SHARED KEY, created an IP address pool & subnet mask to the same range as the routers addresses and left all other options to default
8) I left cTCP unticked and disabled
9) I delivered the commands succesfully
10) I click TEST VPN SERVER and get 3 ticks successful for Server configuration, dependant components & Firewall
11) I open the cisco client and access the VPN internally using the routers LAN address, it prompts for my user name and password, I type it in and connect successfully
12) When I go home I configure my client to the same settings except I change the LAN address for the external WAN ip address, but I get an error message which says "Secure VPN Connection terminated locally by the client. Reason 412: The remote peer is no longer responding"
VPN Client settings are as follows
Group Authentication
Enable Transparent Tunneling- IPSec over UDP (NAT / PAT)
Currently I have a dynamic external IP address, I intend to get a static one once I know I can get this to work.
I would be extremely greatful if someone could help me solve this issue and work out why I can't connect externally.
I have no knowledge of CLI but will use it if given some instructions.
Thanks.
P.S. I have turned off all antivirus and firewall programs on the client computer when trying to connect.Your nat exemption acl is backwards...
access-list 101 permit ip 192.168.2.0 255.255.255.0 192.168.1.0 255.255.255.0
should be...
access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0 -
Can Cisco Configuration Professional to use IPS feature ?
Dear Expert
Hello.
Could you tell me about Cisco Configuration Professional.
I'd like to try the IOS-IPS on Cisco2901-SEC/K9.
I was search in CCO about Cisco Configuration Professional.
The Cisco2901-SEC/K9 does not support SDM.
But, The Cisco2901-SEC/K9 supported the Cisco Configuration Professional.
Can Cisco Configuration Professional to use IPS feature like SDM?
Regards,
Takuro.Hi,
yes, you can configure IOS IPS from Cisco Configuration Professional.
CCP has a wizard to guide you through the process, this is a link for that :
http://www.cisco.com/en/US/prod/collateral/iosswrel/ps6537/ps6586/ps6634/prod_white_paper0900aecd8066d265.html
i hope this helps you.
Mashal -
Cisco Configuration professional corrupt
I downloaded the full zip from http://tools.cisco.com/support/downloads/go/Model.x?mdfid=281795035&mdfLevel=null&treeName=Routers&modelName=Cisco%20Configuration%20Professional&treeMdfId=268437899
from the 1st link, but it seems to be corrupt. The 2nd link gets to the download page but then redirects away to say its not available. What gives?I sent a message to thier web-help support address. If I hear back I'll post.
-
Cisco Configuration Professional on Windows 8.1
Trying to run CCP 2.7 on Windows 8.1. I've already changed the compatibility view settings and the program launches just fine and the view is correct. I am not able to type anything in any of the field. I think this may be due to a Java version or setting. I have downgraded my jave to JRE 1.6.0_11. Any help would be great. What am I missing. Thanks in advance.
I already had the setting in Java and added localhost in IE. Same result. Program will launch but when trying to add devices to the community, I am unable to type anything in any of the fields.
What else would you suggest I use to manage my devices? Consider I am not friendly with IOS commands and need a GUI interface. Thanks. -
Cisco Configuration Professional Error
I just start using CCP .. and It is only opening to half or 1/3 of the ie window. updated adobe no juice. Java? Need some help!!!!! Kind of frustrated since i have trying to get it work for past 1 week.
The solution for this was covered in the Network Management forum at this thread.
-
Cisco Configuration Professional - Takes lot of time on discovering
Dear All,
We are using CCP since a long time without any issue but suddenly it takes a lot of time to discovering a single device than usual.
Can anyone help me on this?
Thanks.Dear All,
We are using CCP since a long time without any issue but suddenly it takes a lot of time to discovering a single device than usual.
Can anyone help me on this?
Thanks. -
Hi All,
I need help on Configuring the Site to Site VPN from Cisco 2811 to Websense Cloud for web Traffic redirect
2811 having C2800NM-ADVIPSERVICESK9-M
2811 router connects to the Internet SW then connects to the Internet router.
Note- For Authentication am using the Device ID & Pre share key. I am worried as all user traffic goes with PAT and not firing up my tunnel for port 80 traffic. Can you please suggest what can be the issue ?
Below is router config for VPN & NAT
crypto keyring ISR_Keyring
pre-shared-key hostname vpn.websense.net key 2c22524d554556442d222d565f545246
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp keepalive 10
crypto isakmp profile isa-profile
keyring ISR_Keyring
self-identity user-fqdn [email protected]
match identity user vpn-proxy.websense.net
crypto ipsec transform-set ESP-NULL-SHA esp-null esp-sha-hmac
crypto map GUEST_WEB_FILTER 10 ipsec-isakmp
set peer vpn.websense.net dynamic
set transform-set ESP-NULL-SHA
set isakmp-profile isa-profile
match address 101
interface FastEthernet0/1
description connected to Internet
ip address 216.222.208.101 255.255.255.128
ip access-group HVAC_Public in
ip nat outside
ip virtual-reassembly
duplex full
speed 100
no cdp enable
crypto map GUEST_WEB_FILTER
access-list 101 permit tcp 192.168.8.0 0.0.3.255 any eq www
access-list 103 deny ip 192.168.8.0 0.0.3.255 host 85.115.41.187 log
access-list 103 deny ip 192.168.8.0 0.0.3.255 host 85.115.41.181 log
access-list 103 deny ip 192.168.8.0 0.0.3.255 host 85.115.41.182 log
access-list 103 deny ip 192.168.8.0 0.0.3.255 86.111.216.0 0.0.1.255
access-list 103 deny ip 192.168.8.0 0.0.3.255 116.50.56.0 0.0.7.255
access-list 103 deny ip 192.168.8.0 0.0.3.255 86.111.220.0 0.0.3.255
access-list 103 deny ip 192.168.8.0 0.0.3.255 103.1.196.0 0.0.3.255
access-list 103 deny ip 192.168.8.0 0.0.3.255 177.39.96.0 0.0.3.255
access-list 103 deny ip 192.168.8.0 0.0.3.255 196.216.238.0 0.0.1.255
access-list 103 permit ip 192.168.8.0 0.0.3.255 any
ip nat pool mypool 216.222.208.101 216.222.208.101 netmask 255.255.255.128
ip nat inside source list 103 interface FastEthernet0/1 overload
ip nat inside source route-map nonat pool mypool overloadHow does Websense expect your source IPs in the tunnel? 192.168.8.0 0.0.3.255 or PAT'ed 216.222.208.101 ?
Check
show crypto isakmp sa
show crypto ipsec sa
show crypto session
You'd better remove the preshared key from your post. -
Cisco WSA : no data found in L4 traffic monitor summary
Hello !
Does L4 traffic monitor only display rogue traffic ? Because, I made a packet capture on the T1 interface and i saw that there was a lot of traffic but in the overview, no data was found in the field "L4 Traffic Monitor Summary". Is it normal ? There is a screenshot in enclosed files.
Thank you,
Stephane WalkerUDP ports will not be blocked.
The L4TM will use the T1 interface to detect traffic to destinations that are on its blacklist. Once detected, the the data interface on the WSA will send a packet with the TCP reset flag to the client to prevent a TCP connection.
I have not tested this so someone correct me if I am wrong. I am answering this based on my understanding of the L4TM feature, and how it works. Since UDP is connectionless, there is no connection for it to kill.
Now this makes me wonder about the Monitor feature though. But I am almost certain it will not block if the action is set to block.
I'll check this out when I'm in the office and will get back to you.
-Vance -
Blocking p2p application traffic and tunneling
I need help ........
We have taken two ASA with AIP card, and have configured Active/Active , but user are using p2p and tunneling softwares . how can we block p2p and tunneling traffic ..
plz anyone reply me..........
regardsIf you are using Firewall software 12.4(9)T and above, it has integrated policies to block or rate limit p2p application traffic using dynamically updateable application
definitions for newer p2p applications. KaZaA, Gnutella, BitTorrent, and eDonkey are currently supported.
You may also see this: http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_tech_note09186a00801e419a.shtml -
How can i configure my iphone to only pass traffic from certain apps over vpn
I have got a telephony app that connects to a phone system through vpn. when I turn on "send all traffic through vpn" internet and other apps are really slow. is their a way to configure the phone to send only traffic from the app through VPN.
Now all my new apps as well as several others are gone from the iPhone.
Look on other screens. The 4.1 update ands Game Center to the home screen. If that screen was full it create a blank screen and moves one app from the home screen to the new screen to make room for Game Center. All the other screens are pushed back one place.
How can I get my apps back? It cost me a lot of time and money to discover those apps and get them onto the phone. Are they just gone now?
If they are really gone, you can download them again. You will not be charged again if you use the same iTunes account. -
I remove default VOIP Monitor Service in "Cisco desktop administrator>Services Configuration > Multiline, Monitoring & Recording >Remove VoIP/Recording & Playback Services". Now I can't choose in "Services Configuration > Multiline, Monitoring & Recording > VoIP Monitoring Device" Default VOIP Monitor Service. How can I return choice my VOIP Monitor Service(IP UCCX)?
Hi Kalitamih,
This can be regenerated by the Cisco Desktop VOIP Monitor Service.
Please stop the service and start it (do not restart). Let me know how it goes and if it resolves the problem.
Regards,
Arundeep -
Configuring Simple monitoring application
Hi
We have a requirement to to create the following
Configure simple monitoring application that will check for the number of concurrent BOBJ sessions used
send out alerts to team and manager when reaching a threshold.
Also if threshold is reached, we should also be restarting one or more CMS in the cluster to get rid of the inactive sessions.
The same application should also have the ability to send out the usage summary by day, week and month as well.
Please assist if there is any possibility of configuring the following in BusinessObjects applications
Thanks & Regards,Have you got any chance to check here?
SAP BusinessObjects 4.0 Monitoring Configuration - Part(1)
SAP BusinessObjects 4.0 Monitoring Configuration - Part(2)
SAP BusinessObjects 4.0 Monitoring Configuration - Part(3)
You can get most of questions answered here
Maybe you are looking for
-
I have 4 and 5 copies of my photos under photos on my ipad. I do not have a delete button to delete them. Also, my icloud is upto date but my new photos are no longer streamimg to my photo stream.
-
ITunes 8 and Windows Vista "sound effect"
So ever since iTunes 8 came out, I get that stupid annoying sound effect whenever doing anything in iTunes. I can turn off the sidebar and it will stop for the most part, but I still get it when going to the iTunes Store or going to my iPod list. I w
-
The ability of the new 2014 Mac Pro to run older legacy OSX versions?
Being a video editor, I will probably be in the market to buy the new Mac Pro when it's released into the marketplace (which should be very soon). So my question is...I usually retain several different startup drives, with different versions of OSX
-
IPad English handwriting to text in form fields
Anyone out there know of any way that I can handwrite a sentence on an iPad and have the sentence converted to text and put into the field? I know there is currently only a built-in Chinese version of this, but hoping that someone knows of a third
-
How to clean the trash forever from locked files?
How to clean the trash forever from locked files?