Cisco Flex 7500 and anchor

Hello, I couldn't find this on the Cisco Flex 7500 specs
http://www.cisco.com/en/US/partner/prod/collateral/wireless/ps6302/ps8322/ps11635/data_sheet_c78-650053.html
Do anybody know if I can set up an anchor mobility group between the Flex 7500 and the WLC 5508?
Kind regards

Yes, 5508 can be used as anchor controller for static anchoring while 7500 as foreign using central swtiching.
For Mobility:
Fault Tolerance
It is recommended to use Flex 7500 as both the primary and backup controllers.
Flex 7500 primary and backup controllers must be in the same mobility domain.
Ref:
http://www.cisco.com/en/US/products/ps11635/products_tech_note09186a0080b7f141.shtml

Similar Messages

  • Cisco Flex 7500 controller with client disconnects

    Hey All,
    There will be alot of info in this post, hopefully all helpful, more info the better right!  If you require anymore info to help me out to not hesistate to request it.
    We have been having some issues with clients connecting and disconnecting several times a day and having to manually reconnect from the icon on their taskbar. We have about 380 APs, and 200+ more to deploy that we have and are licensed for but are having some issues that we want to resolve first obviously.
    Some locations our setup is a bit more complex than this with multiple SSIDs and vlans, but this issue is everywhere so i will keep it to our simple setup for now:
    AP Models: AIR-LAP1042N-A-K9, AIR-CAP1602I-A-K9 (Most locations do not have a mix of both, most have 1042s)
    Running a single SSID - WPA/WPA2 with: WPA - TKIP and WPA2 - AES on the same SSID. 
    They talk back to a Cisco Flex 7500 Series through a tunnel (should not be any port blocking preventing communication)
    We are running from what i understand a bad firmware version (7.6.100.0) and during our next maintenance window i am going to try and get them to change to a more stable firmware version.
    Data Rates of 1,2,5.5,11 Mbps are disabled
    TPCv1 coverage running
    Automatic Power Assignment
    I will not focus on the a/n/ac network as most of our devices are connecting to WPA due to the config they already have.
    Ideally i would like to get rid of WPA all together but i am not 100% in control of the decisions to get the started and people here like to delay things lol.
    It is hard to say if the issue is specific to a model as we have so few 1602Is, and it is just at our main office.  I have not heard many complaints but i have noticed i will now and then get a limited or no connectivity settings on my wireless icon on my PC.  I use hard-wired so i don't really notice if it is not working.
    In most locations it looks like the controller is doing a decent job at selection channels to use. I did find one spot where it had on 11 APs down a long hallway, and did not use channel 6 once. I statically set that location to stagger the channels to see what kind results we had and am still waiting to hear on that as they complained the most out of all of our locations. In some cases 3 APs in a row were on channel 1 in the hallway, in alot of casses 1 was 2 times in a row as well as 11 so there was alot of overlap.
    I am attaching my show sysinfo and show wlan 17 for that informtion, some of the other settings i have changed today that were previously enabled/set different are:
    Disabled Cisco Aironet IE
    Set channel automatic rescan from 10 mintues to 12 hours as i can image if it is changing the channels alot it can lead to disconnects.
    Some of the main things we get in our message log are:
    *dot1xMsgTask: Oct 16 15:17:36.943: #DOT1X-4-MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:508 Max EAPOL-key M5 retransmissions exceeded for client 84:85:06:0b:a6:33 
        - Not sure why we get this as we have a PSK and do not have local eap enabled.....
    *apfMsConnTask_6: Oct 16 15:19:01.753: #APF-3-AID_UPDATE_FAILED: apf_80211.c:6570 Error updating Association ID for REAP AP Clientc8:f9:f9:2b:fd:50 - AID 4
    *apfMsConnTask_6: Oct 16 15:19:01.753: #LWAPP-3-INVALID_AID2: spam_api.c:1462 Association identifier 4 for client 18:9e:fc:4d:9e:87 is already in use by 8c:2d:aa:b7:70:5e
        - There is a bug for this log, but according to the bug our 7.6.100.0 is not effected
    Here is my show sysinfo:
    (Cisco Controller) >show sysinfo
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.6.100.0
    RTOS Version..................................... 7.6.100.0
    Bootloader Version............................... 7.6.101.2
    Emergency Image Version.......................... 7.6.101.2
    Build Type....................................... DATA + WPS
    System Name...................................... Cisco_cf:17:26
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1295
    Redundancy Mode.................................. Disabled
    IP Address....................................... 10.156.50.100
    System Up Time................................... 52 days 5 hrs 54 mins 25 secs
    System Timezone Location......................... (GMT -4:00) Altantic Time (Canada)
    System Stats Realtime Interval................... 5
    System Stats Normal Interval..................... 180
    Configured Country............................... CA  - Canada
    --More-- or (q)uit
    Operating Environment............................ Commercial (10 to 35 C)
    Internal Temp Alarm Limits....................... 10 to 38 C
    Internal Temperature............................. +22 C
    Fan Status....................................... OK
    RAID Volume Status............................... OK
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 13
    Number of Active Clients......................... 1584
    Burned-in MAC Address............................ 70:81:05:CF:17:20
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Present, OK
    Maximum number of APs supported.................. 600
    Here is my Show wlan 17
    WLAN Identifier.................................. 17
    Profile Name..................................... AirCCRSB
    Network Name (SSID).............................. AirCCRSB
    Status........................................... Enabled
    MAC Filtering.................................... Disabled
    Broadcast SSID................................... Enabled
    AAA Policy Override.............................. Disabled
    Network Admission Control
    Client Profiling Status
        Radius Profiling ............................ Disabled
         DHCP ....................................... Disabled
         HTTP ....................................... Disabled
        Local Profiling ............................. Disabled
         DHCP ....................................... Disabled
         HTTP ....................................... Disabled
      Radius-NAC State............................... Disabled
      SNMP-NAC State................................. Disabled
      Quarantine VLAN................................ 0
    Maximum number of Associated Clients............. 0
    Maximum number of Clients per AP Radio........... 200
    Number of Active Clients......................... 1768
    Exclusionlist Timeout............................ 60 seconds
    Session Timeout.................................. 28800 seconds
    User Idle Timeout................................ Disabled
    Sleep Client..................................... disable
    Sleep Client Timeout............................. 12 hours
    User Idle Threshold.............................. 0 Bytes
    NAS-identifier................................... Cisco_cf:17:26
    CHD per WLAN..................................... Enabled
    Webauth DHCP exclusion........................... Disabled
    Interface........................................ management
    Multicast Interface.............................. Not Configured
    WLAN IPv4 ACL.................................... unconfigured
    WLAN IPv6 ACL.................................... unconfigured
    WLAN Layer2 ACL.................................. unconfigured
    mDNS Status...................................... Disabled
    mDNS Profile Name................................ unconfigured
    DHCP Server...................................... Default
    DHCP Address Assignment Required................. Disabled
    Static IP client tunneling....................... Disabled
    Quality of Service............................... Silver
    Per-SSID Rate Limits............................. Upstream      Downstream
    Average Data Rate................................   0             0
    Average Realtime Data Rate.......................   0             0
    Burst Data Rate..................................   0             0
    Burst Realtime Data Rate.........................   0             0
    Per-Client Rate Limits........................... Upstream      Downstream
    Average Data Rate................................   0             0
    Average Realtime Data Rate.......................   0             0
    Burst Data Rate..................................   0             0
    Burst Realtime Data Rate.........................   0             0
    Scan Defer Priority.............................. 4,5,6
    Scan Defer Time.................................. 100 milliseconds
    WMM.............................................. Allowed
    WMM UAPSD Compliant Client Support............... Disabled
    Media Stream Multicast-direct.................... Disabled
    CCX - AironetIe Support.......................... Disabled
    CCX - Gratuitous ProbeResponse (GPR)............. Disabled
    CCX - Diagnostics Channel Capability............. Disabled
    Dot11-Phone Mode (7920).......................... Disabled
    Wired Protocol................................... None
    Passive Client Feature........................... Disabled
    Peer-to-Peer Blocking Action..................... Disabled
    Radio Policy..................................... All
    DTIM period for 802.11a radio.................... 1
    DTIM period for 802.11b radio.................... 1
    Radius Servers
       Authentication................................ Global Servers
       Accounting.................................... Global Servers
          Interim Update............................. Disabled
          Framed IPv6 Acct AVP ...................... Prefix
       Dynamic Interface............................. Disabled
       Dynamic Interface Priority.................... wlan
    Local EAP Authentication......................... Disabled
    Security
       802.11 Authentication:........................ Open System
       FT Support.................................... Disabled
       Static WEP Keys............................... Disabled
       802.1X........................................ Disabled
       Wi-Fi Protected Access (WPA/WPA2)............. Enabled
          WPA (SSN IE)............................... Enabled
             TKIP Cipher............................. Enabled
             AES Cipher.............................. Disabled
          WPA2 (RSN IE).............................. Enabled
             TKIP Cipher............................. Disabled
             AES Cipher.............................. Enabled
                                                                   Auth Key Management
             802.1x.................................. Disabled
             PSK..................................... Enabled
             CCKM.................................... Disabled
             FT-1X(802.11r).......................... Disabled
             FT-PSK(802.11r)......................... Disabled
             PMF-1X(802.11w)......................... Disabled
             PMF-PSK(802.11w)........................ Disabled
          FT Reassociation Timeout................... 20
          FT Over-The-DS mode........................ Enabled
          GTK Randomization.......................... Disabled
          SKC Cache Support.......................... Disabled
          CCKM TSF Tolerance......................... 1000
       WAPI.......................................... Disabled
       Wi-Fi Direct policy configured................ Disabled
       EAP-Passthrough............................... Disabled
       CKIP ......................................... Disabled
       Web Based Authentication...................... Disabled
       Web-Passthrough............................... Disabled
       Conditional Web Redirect...................... Disabled
       Splash-Page Web Redirect...................... Disabled
       Auto Anchor................................... Disabled
       FlexConnect Local Switching................... Enabled
       flexconnect Central Dhcp Flag................. Disabled
       flexconnect nat-pat Flag...................... Disabled
       flexconnect Dns Override Flag................. Disabled
       flexconnect PPPoE pass-through................ Disabled
       flexconnect local-switching IP-source-guar.... Disabled
       FlexConnect Vlan based Central Switching ..... Disabled
       FlexConnect Local Authentication.............. Disabled
       FlexConnect Learn IP Address.................. Enabled
       Client MFP.................................... Optional
       PMF........................................... Disabled
       PMF Association Comeback Time................. 1
       PMF SA Query RetryTimeout..................... 200
       Tkip MIC Countermeasure Hold-down Timer....... 60
       Eap-params.................................... Disabled
    AVC Visibilty.................................... Disabled
    AVC Profile Name................................. None
    Flow Monitor Name................................ None
    Split Tunnel (Printers).......................... Disabled
    Call Snooping.................................... Disabled
    Roamed Call Re-Anchor Policy..................... Disabled
    SIP CAC Fail Send-486-Busy Policy................ Enabled
    SIP CAC Fail Send Dis-Association Policy......... Disabled
    KTS based CAC Policy............................. Disabled
    Assisted Roaming Prediction Optimization......... Disabled
    802.11k Neighbor List............................ Disabled
    802.11k Neighbor List Dual Band.................. Disabled
    Band Select...................................... Disabled
    Load Balancing................................... Disabled
    Multicast Buffer................................. Disabled
     Mobility Anchor List
     WLAN ID     IP Address            Status
    802.11u........................................ Disabled
    MSAP Services.................................. Disabled
    Local Policy
    Priority  Policy Name

    As long as you take the configuration backup downgrading from 7.6.100.0 to 7.4.121.0 should be fine. Because this is Flexconnect deployment, make sure you review the release notes thoroughly as config like vlan mapping is impacted it is painful to reconfigure.
    I still think moving to 7.6MR3 & once 8.x get stable going for that code is a good plan. Though 7.4.121.0 is assure wave it does not mean it has no bugs.(remember that prior to this 7.4.110.0 was assure wave & it deferred in quick time) . I would say 8.x going to be the code staying for long time period, so ultimately you have to be there.
    In 8.x there are few FlexConnect improvements,one being AP won't reload when you change from local mode to FlexConnect.
    HTH
    Rasika
    **** Pls rate all useful responses ***

  • Cisco Flex Connect and users can not get IP Address by WAN

    Hello my name is Ivan
    I have a wlc 5508 with license base to 50 aps, i use a deployment flex connect. I already registered all my access points, I use web authentication to authenticate users guest, and the service dhcp is in the central site.
    My issue is the users in each remote site, can not get an ip address by dhcp from the central site, they can authenticate in the guest ssid, but any users can not get an ip.
    The request is passing by the wan in this way
    Central Site DHCP - Router WAN - Remote Site - Users with notebooks. I use flex connect central deployment (all the traffic consulting to the wlc) .
    perhaps i should use local deploy? The wlc is in the central site.
    Can you help me to resolving this issue please? , perhaps any advice?
    Regards
    Ivan.

    Thanks Osita
    If I configure Central Authentication and  I configure central switching I need to create a dynamic interafce for each remote site and each dynamic interface associated with a different VLAN ID, because I can not associate a single interface dynamic to the same  VLAN ID, but in my case the client remote in each remote site have the same network segment with the same VLAN ID with the same SSID for guests. My goal is to configure web authentication with the local DHCP server at each remote site, will this work?.Each remote site have its own server dhcp.
    If I configure authentication central authentication with central switching with web authenticacion as I set in my scenario?
    My issues are the interfaces dynamics, because I have the same network to the customer guest with the same ID VLan in each remote site
    Regards

  • WLC 5508 and Flex 7500

    Hi,
    I am going to deploy 5508 with 12 AP version now..
    In future, we are going to get another Cisco Flex 7500 Series Cloud Controller.
    My question is can 5508 run N+1 redundancy with 7500? or is there any best practice or upgrade path avail?
    Thanks,
    John

    My understanding is that the 7500 cloud controller is for H-REAP only implementations and if it could be used as an N+1 (which I haven't heard it can) like Leolaohoo said it'd only be useful for your H-REAP access points and not your local mode ap's.. they are intended for drastically different network topology and scenarios.

  • DAC cable between HP Flex-10 and Cisco 4900M

    We have HP C7000/VC-Flex 10 Module that I would like to connect to our Netapps NFS datastore.  The Cisco switch that I will be using between HP Flex-10 and Netapps is Cisco 4900M.  I have a HP cable AP784A direct attach copper SFP+ to SFP+.  Which module I need to purchase and insert into my 4900M to support 10Gb connectivity via HP DAC 10Gb cable.
    Please Advise!

    You need
    4900M 4 port 10GE half card with X2 interfaces (WS-X4904-10GE)
        OR
    4900M 8 port 10GE half card with X2 interfaces (WS-X4908-10GE)
    WITH
    Cisco OneX Converter Module Converts an X2 Interface into One SFP+ Interface (CVR-X2-SFP10G)
    I would recommend you to use following DAC cables from Cisco.
    • SFP-H10GB-CU1M: 10GBASE-CU SFP+ Cable 1 meter (Version -02)
    • SFP-H10GB-CU3M: 10GBASE-CU SFP+ Cable 3 meter (Version -02)
    • SFP-H10GB-CU5M: 10GBASE-CU SFP+ Cable 5 meter (Version -02)

  • Issue with AP 3702i, AP not registered in Flex 7500

    Hi
    My problem is this , I have several Access Points 3702i , which are seteados with Static IP , which were previously configured . When connected to the network , they are not able to register with the WLC Flex 7500, the AP reachable from the WLC for ping , but still not recorded.
    I connected to the network, I connect the console to the AP and I reconfigure the AP two or three times, until it is able to register.
    Anyone know if this happens over a Bug or a series of equipment failures that come with ????
    The Access Point throws typical logs trying to connect to the WLC , try enocntrar a DHCP and restarted , despite having a Static ip and is reachable from the WLC .
    Greetings and esperi someone can answer .

    What code running on your 7500 ? 3700 require 7.6.100.x or above
    http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html
    If possible attach the console output of the AP while this issue is happening. That will tell us reason for the failures
    HTH
    Rasika
    *** Pls rate all useful responses ***

  • Wireless Guest Network using Cisco 4402 as an Anchor Controller

    Hello,
    We have recently redesigned our wireless guest network in accordance to Cisco's recommended deployment using the anchor controller in the DMZ. We have created two mobility groups (enterprise and anchor). The anchor controller and DMZ has two subnets (guest managment and guest clients). The guest management subnet is connected to the controller and firewall allowing the mobility groups and EOIP tunnels while the guest client network is also connected to the controller and firewall to push the client traffic directly out the firewall. The setup works well but the one part that I'm not happy with is the DHCP. Currently DHCP is being handled on the firewall because of issues we had with dhcp relay and the controllers internal dhcp service.
    Does anyone have any information on getting DHCP relay working or the internal dhcp service on the controllers when using as a anchor?
    This is basically the setup guide that we followed.
    http://www.cisco.com/en/US/docs/solutions/Enterprise/Mobility/emob41dg/ch10GuAc.html
    Thanks!

    Hi,
    Make sure you have the IP helper address configured under the VLAN interface on the L3 and also make sure to disable DHCP proxy on both the WLC (Anchor and Foreign).
    This will help us as well..
    lemme know if this answered your question..
    Regards
    Surendra
    ====
    Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

  • WLC 5508 and Anchor/GuestNet rate limit traffic?

    Running WLCs 5508s 7.0.116.0 with GuestNet and Anchor setup, how can I limit the bandwidth on the GuestNet SSDI to 2 Mbps, etc?
    The DMZ WLC (Anchor) runs thru a ASA 5508 7x, can I rate limit traffic via ASA?

    That's really a matter of preference.  This document describes things to keep in mind when altering these QoS profile configurations, FYI.
    http://www.cisco.com/en/US/partner/docs/wireless/controller/7.0MR1/configuration/guide/cg_controller_setting.html#wp1254532
    It really depends on how many guests, what type of traffic, etc, to make a judgement call as to where you should set these.  I'm sorry but I don't have any examples from existing configurations, but hopefully the document explains how to best alter these settings.

  • Flex 7500 Wireless SFP

    The documentation states the Flex 7500 WLAN controllers support the 10Gig transcever "SFP-10G-SR" but mentions no others. Is it possible to install a 1Gig transceiver such as GLC-T or GLC-SX-MM or other types of 10Gig transceivers.                  

    No.. The Flex7500 is pure 10gig connection only.
    Sent from Cisco Technical Support iPhone App

  • Cisco Phone Control and Presence 8.6.1.1185 with IBM Lotus Notes 8.5.2 (Integrated Sametime Client 8.0.2) - No presence status visible

    Hi community,
    I am trying to integrate Cisco Unified Presence 8.6.1.10000-34 with IBM Lotus Notes 8.5.2 with the integrated Sametime Client version 8.0.2 via the Cisco Plugins 8.6.1.1185.
    Phone control is working fine, whereas the presence status is not shown (= no handset symbol next to the Sametime user). When I look in the preferences of the plugin, I can see that the plugin has connected successfully to the CUCM (8.6.2.20000-2),whereas the connection to the CUPS has not been established.
    The user id as well as the password are all the same on all systems. Here is a description of what I have configured via the ciscocfg.exe tool:
    Feature Control:
    - Enable Phone Status -> checked
    - Enable Dial Using Cisco IP Communicator -> unchecked (not required)
    - Enable Control Desk Phone -> checked
    - Default Mode -> Control Desk Phone
    Control Desk Phone Settings:
    - Voicemail Pilot Number -> left blank (no voicemail)
    - Cisco Unified Communications Manager
         - Servers -> IP address of CUCM
         - Read Only -> unchecked
         - Use as Default CUCM -> checked
         - Synchronize Credentials -> checked
              - Use Sametime Credentials -> checked
    Use Secure Connection: -> not required
    LDAP Phone Attributes: -> not required
    Phone Status Settings:
    - Cisco Unified Presence Servers -> IP address of CUPS
    - Read Only -> unchecked
    - Synchronize Credentials -> checked
         - Use Sametime Credentials -> checked
    - Sametime User ID Mapping
         - Use Business Card Attribute -> MailAddress
         - Remove Domain -> checked
    - Display Off-Hook Status Only -> unchecked
    At the moment I don't see an error in the configuration, but maybe I am wrong. Could anyone please tell me what the error could be?
    Thanks a lot in advance!
    Kind regards,
    Igor

    Hi all,
    here are some additions to my above post:
    Servers and clients used:
    1x CUCM 8.6.2.20000-2
    1x CUPS 8.6.1.10000-34
    1x IBM Lotus Domino Messaging Express Server 8.5.2
    1x Sametime Entry Server 8.5.2 (on top of the Domino server)
    2x IBM Lotus Notes 8.5.2 with integrated Sametime 8.0.2
    2x Cisco Phone Control and Presence with Lotus Sametime (PCAP) 8.6.1.1185
    2x Cisco Unified Personal Communicator 8.5.5.19839
    Setup:
    - CUCM, CUPS and CUPC are working fine, i.e. Desk Phone control via CUPC, as well as availability and presence status are working without issues
    - IBM Lotus Domino server is the LDAP Directory, the Sametime Entry Server is installed on top of the Domino server and uses the Domino Directory
    - User ID and password on CUCM/CUPS match the ShortName field and password in Domino
    - The PCAP plug-in has been manually deployed to both Notes clients with the following configuration:
         - Enable Phone Status -> active
         - Desk Phone Control -> active
         - no credential synchronization for CUCM and CUPS, i.e. every user must fill the user details himself
         - Sametime User ID Mapping is implemented via the LDAP Attribute uid (which is equal to the user id in CUCM)
         - LDAP configuration filled in with details of the Domino server
    Phone Control is working fine, also the connection to the LDAP server (Domino) is fine. However, when I type in the credentials for the CUPS server login, I can see (in Troubleshooting pane) that the user (pparker) is connected to the CUPS server for a short period of time and then gets disconnected. After that no connection is possible to the CUPS server, i.e. status is always disconnected.
    I have collected the Tomcat (EPASSoap00010.log and security00010.log) logs via RTMT and compared them to the logs from the PCAP plugin. The relevant time period is from 15:14 to 15:17. In the Tomcat logs I can see that the authentication is successful (see attached files), however in the log of PCAP plugin I can see the following messages:
    2012/02/03 15:14:35.281 WARNUNG Credential is rejected. Nothing to retry ::class.method=com.cisco.sametime.phonestatus.cup.CUPPresenceWatcher.answerChallenge() ::thread=CT_CALLBACK.1 ::loggername=com.cisco.sametime.phonestatus.cup
    2012/02/03 15:14:35.281 WARNUNG #### Connection rejected presence server ::class.method=com.cisco.sametime.phonestatus.cup.CUPPresenceWatcher.onPresenceServerConnectionRejected() ::thread=CT_CALLBACK.1 ::loggername=com.cisco.sametime.phonestatus.cup
    2012/02/03 15:14:35.281 WARNUNG Credential is rejected. Nothing to retry ::class.method=com.cisco.sametime.phonestatus.cup.CUPPresenceWatcher.answerChallenge() ::thread=CT_CALLBACK.2 ::loggername=com.cisco.sametime.phonestatus.cup
    2012/02/03 15:14:35.281 WARNUNG #### Connection rejected presence server ::class.method=com.cisco.sametime.phonestatus.cup.CUPPresenceWatcher.onPresenceServerConnectionRejected() ::thread=CT_CALLBACK.2 ::loggername=com.cisco.sametime.phonestatus.cup
    I don't understand why the connection is rejected although the Sametime Internal ID and CUPS User ID match. Does anyone know what the issue could be?
    All posts are very much appreciated!
    Thanks a lot in advance!
    Kind regards,
    Igor

  • Boot camp with Cisco VPN client and smart card

    Looking at a Macbook or Macbook Air and the only reason I need to run windows is to be able to access my work network through the Cisco VPN client and my Smartcard then use remote desktop. From my understanding if I run Bootcamp it should work am I correct? Im going to an Apple store tomorrow hopefully they can help too.
    Thanks

    mrbacklash wrote:
    Ok with that being said will the MBA 11.6 1.4ghz have the guts to make it run mostly internet based programs over the VPN connection?
    I think if you are running apps over the Internet the bottleneck will be the Internet and your VPN bandwidth. Your computer can certainly execute faster than Internet communications.
    Besides, Internet or remote applications run on the remote server. All your local computer does is local processing of the data if necessary.
    Message was edited by: BobTheFisherman

  • Cisco VPN Client and Mac OS 10.5.1 update

    After upgrading to Leopard (10.5) my Cisco VNP client stopped working. I was able to fix that by downloading the newer VPN Client 4.9.01 (0080) from the Macupdate.com website. Now that I've updated to Mac OS 10.5.1, the VPN Client won't work again!! I went back to the Macupdate website and downloaded what looks like an even newer version - 4.9.01 (0090) - but this is labeled as a BETA and it doesn't work either. Anyone out there seen a newer version, or something that works with 10.5.1?

    b166er wrote:
    Aside from the fact that it's marked beta, I'm wary about the source of MacUpdate's download. They link to http://www.arrange.co.at/download/vpnclient-darwin-4.9.01.0090-universal-k9-BETA .dmg
    Cisco don't ever make the client freely available. The official download is via form on the Cisco web site and you need appropriate credentials. I wouldn't risk installing from any other source.
    The home page at http://www.arrange.co.at/ doesn't exactly inspire confidence.
    Dude has a point... it's risky to mess with something like this from an untrusted source IMHO. Cisco is picky about who they give it out to. I have to get mine through my host provider since they are the ones that are authorized.
    For what it's worth, I'm using 4.9.01 with 10.5.1 and it works well.

  • I am unable to browse internet from my cisco 881 router and configuration is below could any one help me in this regard

    HOME#sho run
    Building configuration...
    Current configuration : 5657 bytes
    ! Last configuration change at 10:51:11 UTC Fri May 17 2013 by admin
    version 15.0
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname HOME
    boot-start-marker
    boot-end-marker
    logging buffered 51200 warnings
    enable secret 5 $1$bgx9$VrtQW3Wg182VyYhKAHLbN.
    no aaa new-model
    memory-size iomem 10
    crypto pki trustpoint TP-self-signed-1190003239
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1190003239
    revocation-check none
    rsakeypair TP-self-signed-1190003239
    crypto pki certificate chain TP-self-signed-1190003239
    certificate self-signed 01
      3082024A 308201B3 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
      31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
      69666963 6174652D 31313930 30303332 3339301E 170D3133 30353137 31303333
      35315A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
      4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 31393030
      30333233 3930819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
      8100C002 80BBF151 E095E469 AA7DBB18 2A9E3CC2 4AC223F6 ABE0AF49 876C1203
      65D0E246 786F174D E5B7897A 44C5755A 2571E58A 184A6C62 DD992A2A D8A24878
      25A8D3C3 03F5D3C2 522EC8BB 302B0CCD 2945087A 7AF01418 D0056679 6F64DB4A
      BE2D5DA1 106CD03A 83B422A2 3CCBAE88 F2413123 12269390 6949DFE0 411118E7
      8F210203 010001A3 72307030 0F060355 1D130101 FF040530 030101FF 301D0603
      551D1104 16301482 12484F4D 452E7777 772E7961 686F6F2E 636F6D30 1F060355
      1D230418 30168014 3D2D854D 1203F50D 77F4ABC5 B61CEAF6 C922F4DF 301D0603
      551D0E04 1604143D 2D854D12 03F50D77 F4ABC5B6 1CEAF6C9 22F4DF30 0D06092A
      864886F7 0D010104 05000381 8100B24C 48BACACE 87ADEA03 386F2045 CC89624A
      4EB1AD09 062EB2A4 CF4C96CA 0B2CF001 BD2C3804 8DC47FED 6A5B5F0D 3965AC6E
      4FC4682F 707E4132 8F27C083 C7FAE1BD 21D055E6 C79D5DAD 051B6321 D35DB4F2
      044E6BBD DAD08B6A 6ED87C7E 08F4F7E1 4EFDFB6F 867AF6FA 84165CFC D219D56F
      A82EABD4 AD9CFA24 A5088145 E571
            quit
    ip source-route
    ip routing protocol purge interface
    ip dhcp excluded-address 10.10.10.1
    ip dhcp pool ccp-pool
       import all
       network 10.10.10.0 255.255.255.248
       default-router 10.10.10.1
       domain-name www.google.com
       dns-server 192.168.1.1
       lease 0 2
    ip cef
    ip domain name www.yahoo.com
    ip name-server 84.235.6.55
    ip name-server 84.235.57.230
    no ipv6 cef
    multilink bundle-name authenticated
    license udi pid CISCO881-SEC-K9 sn FCZ1516933C
    username admin privilege 15 password 0 cisco
    interface FastEthernet0
    interface FastEthernet1
    interface FastEthernet2
    interface FastEthernet3
    interface FastEthernet4
    ip address dhcp
    ip access-group 101 in
    ip nat outside
    ip virtual-reassembly
    duplex auto
    speed auto
    interface Vlan1
    description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
    ip address 10.10.10.1 255.255.255.0
    no ip redirects
    no ip unreachables
    no ip proxy-arp
    ip nat inside
    ip nat enable
    ip virtual-reassembly
    ip tcp adjust-mss 1452
    interface Vlan2
    no ip address
    ip nat inside
    ip virtual-reassembly
    ip default-gateway 192.168.1.1
    ip forward-protocol nd
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    ip nat inside source list 101 interface FastEthernet4 overload
    ip route 0.0.0.0 0.0.0.0 FastEthernet4
    access-list 23 permit 10.10.10.0 0.0.0.7
    access-list 101 permit ip any any
    dialer-list 1 protocol ip permit
    no cdp run
    control-plane
    banner exec ^C
    % Password expiration warning.
    Cisco Configuration Professional (Cisco CP) is installed on this device
    and it provides the default username "cisco" for  one-time use. If you have
    already used the username "cisco" to login to the router and your IOS image
    supports the "one-time" user option, then this username has already expired.
    You will not be able to login to the router with this username after you exit
    this session.
    It is strongly suggested that you create a new username with a privilege level
    of 15 using the following command.
    username <myuser> privilege 15 secret 0 <mypassword>
    Replace <myuser> and <mypassword> with the username and password you
    want to use.
    ^C
    banner login ^C
    Cisco Configuration Professional (Cisco CP) is installed on this device.
    This feature requires the one-time use of the username "cisco" with the
    password "cisco". These default credentials have a privilege level of 15.
    YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE
    PUBLICLY-KNOWN CREDENTIALS
    Here are the Cisco IOS commands.
    username <myuser>  privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want
    to use.
    IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL
    NOT BE ABLE TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.
    For more information about Cisco CP please follow the instructions in the
    QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp
    ^C
    banner motd ^Cuthorized ^C
    line con 0
    login local
    no modem enable
    line aux 0
    line vty 0 4
    access-class 23 in
    privilege level 15
    password cisco
    logging synchronous
    login local
    transport input telnet ssh
    scheduler max-task-time 5000
    end

    HOME#ping 4.2.2.2
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 4.2.2.2, timeout is 2 seconds:
    Success rate is 0 percent (0/5)
    HOME#sh ip int br
    Interface                  IP-Address      OK? Method Status                Protocol
    FastEthernet0              unassigned      YES unset  down                  down
    FastEthernet1              unassigned      YES unset  down                  down
    FastEthernet2              unassigned      YES unset  down                  down
    FastEthernet3              unassigned      YES unset  down                  down
    FastEthernet4              192.168.1.120   YES DHCP   up                    up 
    NVI0                       10.10.10.1      YES unset  up                    up 
    Vlan1                      10.10.10.1      YES NVRAM  down                  down
    Vlan2                      unassigned      YES NVRAM  down                  down
    HOME#
    fast ethernet is connected to my internet connection

  • Flex SDK and AIR runtime version in mobile

    Hi, guys.
    I'm trying to make my first Flex mobile app.
    I'm a little confused about the relationship between Flex SDK and AIR  runtime versions for mobile development.
    In the "Developing Mobile Applications with ADOBE FLEX 4.6 and ADOBE FLASH BUILDER 4.6" pdf document, it says:
    "AIR requirements
    Flex mobile projects and ActionScript mobile projects require AIR 2.6 or a higher version. You can run mobile projects on physical devices that support AIR 2.6 or a higher version of AIR.
    You can install AIR 2.6 or a higher version only on supported Android devices that run Android 2.2 or a higher version. For the complete list of supported Android devices, see Certified Devices. Also, review the minimum system requirements to run Adobe AIR on Android devices at Mobile System Requirements.
    Note: If you do not have a device that supports AIR 2.6 or a higher version of AIR, you can use Flash Builder to launch and debug mobile applications on the desktop."
    So, I go and check the Certified devices in http://www.adobe.com/devnet-apps/flashruntimes/certified-devices.html and find that the minimun FLASH PLAYER version accepted by ALL devices is FP 10.1
    1. Does this mean that if I want to release an app to target ALL mobile devices, then I can only use Flex 4.5?
    2. Do support for Flash Player mean the same than support for Adobe AIR? Or the application will prompt the user to install whatever version of the AIR runtime and all of them would be supported by the device, even in the FLASH PLAYER support is for a lesser version?
    Thanks!

    Thanks for your help, Flex harUI,
    The first impression that comes to mind is that FP version is indeed only for the web browser plugin. Then, why does the official Flex 4.6 mobile development documentation have a link to that page that only speaks about the supported FP version in mobiles under the title "AIR requirements"??
    This makes it way too confusing.
    Do you know whether there is something like an equivalent matrix/list of mobile devices with their supported AIR runtime versions?  I went a great deal in trying to keep my original app under 400kb... I didn't know that in the end it would end up weighing 9.5Mb... :S
    Thanks again,

  • What is the maximum number of PVC's supported by Cisco BPX 8620 and 8680 chassis with BCC-4V 128MB DRAM and 4 MB BRAM?

    We are working on a capacity planning project for one of our customers and we need an estimate on the maximum number of PVCs supported in the following situations:
    a)Cisco BPX 8620 and 8680 chassis with BCC-4V 128MB DRAM and 4 MB BRAM ?
    b)Maximum number of PVC's supported by each of the following STM-1 cards:
    - model BXM-155-4D and 4DX ?
    - model BXM-155-8D and 8DX ?

    a)It depends upon software level. b) 16,000 per card, With release 9.3:
    60K Connections Support on BXM-E—Provides the ability to support a maximum of 60K per card for VSI applications for the BPX 8600, for example, PNNI or MPLS, used on enhanced BXM-E cards.

Maybe you are looking for

  • Purchase order list(list of all tables that efect when i entered a po)

    is there any script ,to know what all tables will effect when i entered po deatils and i approve that etc.. if any list is there can any one tell me please. regards satish.

  • Sendmail/Dovecot issue

    I tried to set up a mailserver on my server, and it is possible to recieve mails normally. Strangely, whenever I connect to my server via a mailclient, it does not seem to get any emails, nor can I send any. The error message May 25 15:47:37 thunders

  • SCOM Agent Cache

    Hi Guys, we have SCOM 2012 SP1 in production. I'm receiving complaints from the customer that SCOM has failed to alert on an event. Example: though the agent service is running and the threshold is breached, logical disk monitor, service monitor (man

  • HCM Forms and Process

    Hi all,    Is it even possible to change the Effective date of SAP_PA action? I have 4 backend service, SAP_PA Serv_1 Serv_2 SAP_PA I changed EFFECTIVE_DATE ( Field is available as input field in the form) in my Serv_1 also to ensure I changed it in

  • Progressive Download problems

    I have created an swf, and imported a .flv using progressive download. Once imported, I see the video playback box and tools on the screen. However, when I publish the .swf, or "test movie," there is nothing where the .flv should be. The playback too