Cisco FXO Port disconnect with DMS-10
Hello,
We have a situation where FXO ports are connected to DMS-10 at telco end. DMS-10 doesn't send out any disconnect tone or power denial. Is there a way to detect on CISCO ISR that remote party has disconnected call? Is there a way to disconnect a call after no activity on line after certain amount of time? CO has confirm that they have increase silent on lines to give ISR chance to disconnect the call.
Thank You.
timer media-inactive To enable the timer for media inactivity detection using the digital signal processor (DSP) (based on RTP as the only criterion) and to configure a multiplication factor based on the real-time control protocol (RTCP) timer interval, use the timer media-inactive command in gateway configuration mode. To reset to the default, use the no form of this command. timer media-inactive multiple no timer media-inactive multiple
When the timer media-inactive command is used, the gateway uses the inactivity timer as a combination of the timer media-inactive command and the ip rtcp report interval command. The timer media-inactive command uses DSP statistics. This capability is based on the configuration of callfeature parameters using application command-line interface (CLI) to enable control. The media are considered inactive only if there is no transfer of RTP packets in the send direction and no RTP packets in the receive direction. If RTP is present in either the send or receive direction, it is considered active. In this mode, DSP filters out any comfort noise packets, and the presence of any comfort noise packet is considered inactivity in either direction. The multiple argument (or multiplication factor) is multiplied by the interval that is set using the ip rtcp report interval command. This command configures the average interval between successive RTCP report transmissions for a given voice session. For example, if the value argument is set to 25,000 milliseconds, an RTCP report is sent every 25 seconds, on average. If no RTP packets are received during the calculated interval, the call is disconnected. The gateway signals the disconnect to the VoIP network and the time-division multiplexing (TDM) network so that upstream and downstream devices can clear their resources.
Sent from Cisco Technical Support iPad App
Similar Messages
-
Any fix for USB 3 port disconnects with Plugable GigE adapter on Yoga Pro 2
Hi,
Does anyone know if there is a fix intended from lenovo on this?
Very pleased overall with my Yoga Pro 2, however one issue is that I sometimes need to use a GigE adapter and the Plugable USB3-E1000 I bought will disconnect periodically - mainly an issue when using the link heavily.
It is acknowledged by plugable to be an issue:
http://plugable.com/products/usb3-e1000 "There is known conflict with the Lenovo Yoga 2 Pro’s USB 3.0 port and the USB3-E1000. Symptoms include sudden loss of connectivity and failing of transferring files across a network. The current workaround is to use the USB 2.0 port. We are working with ASIX and Lenovo to resolve this known bug."
It transmits at about 1.5MB/sec on USB2 and 15MB/sec on USB3 so a clear preference to use USB3!
Thanks
Stuart
PS RUnning windows 8. fully patched, have updated BIOS from 1.15 to 1.16If used an external USB Wifi adapter that worked fine (Asus).
This Linksys should also work in the Yoga.
Freedom of Speech has just left the building -
Cisco MDS port channel with USC FI
Hello,
Can anyone help me to configure/troubleshoot Cisco MDS 9148 with Cisco USC ? M stuck in port channel..i have configured but interfaces are not coming UP.It is showing init state.
My Topology is like,
Nexus 5000-->USC FI (single FI) -->Cisco MDS 9148
--> Two Chassis
Any help would be highly appreciated...
ThanxTMC-UCSFI-A-A(nxos)# sh interface brief
Interface Vsan Admin Admin Status SFP Oper Oper Port
Mode Trunk Mode Speed Channel
Mode (Gbps)
fc1/31 1 NP off errDisabled swl -- --
fc1/32 1 NP off errDisabled swl -- --
Ethernet VLAN Type Mode Status Reason Speed Port
Interface Ch #
Eth1/1 1 eth fabric up none 10G(D) --
Eth1/2 1 eth fabric up none 10G(D) --
Eth1/3 1 eth fabric up none 10G(D) --
Eth1/4 1 eth fabric up none 10G(D) --
Eth1/5 1 eth access down SFP not inserted 10G(D) --
Eth1/6 1 eth access down SFP not inserted 10G(D) --
Eth1/7 1 eth access down SFP not inserted 10G(D) --
Eth1/8 1 eth access down SFP not inserted 10G(D) --
Eth1/9 1 eth access down SFP not inserted 10G(D) --
Eth1/10 1 eth access down SFP not inserted 10G(D) --
Eth1/11 1 eth access down SFP not inserted 10G(D) --
Eth1/12 1 eth access down SFP not inserted 10G(D) --
Eth1/13 1 eth access down SFP not inserted 10G(D) --
Eth1/14 1 eth access down SFP not inserted 10G(D) --
Eth1/15 1 eth trunk up none 10G(D) 100
Eth1/16 1 eth trunk up none 10G(D) 100
Eth1/17 1 eth fabric up none 10G(D) --
Eth1/18 1 eth fabric up none 10G(D) --
Eth1/19 1 eth fabric up none 10G(D) --
Eth1/20 1 eth fabric up none 10G(D) --
Eth1/21 1 eth access down SFP not inserted 10G(D) --
Eth1/22 1 eth access down SFP not inserted 10G(D) --
Eth1/23 1 eth access down SFP not inserted 10G(D) --
Eth1/24 1 eth access down SFP not inserted 10G(D) --
Eth1/25 1 eth access down SFP not inserted 10G(D) --
Eth1/26 1 eth access down SFP not inserted 10G(D) --
Eth1/27 1 eth access down SFP not inserted 10G(D) --
Eth1/28 1 eth access down SFP not inserted 10G(D) --
Eth1/29 1 eth access down SFP not inserted 10G(D) --
Eth1/30 1 eth access down SFP not inserted 10G(D) --
output ommitted
TMC-UCSFI-A-A(nxos)#
Here it shows that Fc1/31- 32 which are in trunk , status is errdisabled and admin trunk mode is off -
Issue with SPA525g registation and FXO port call calls are not disconnecting properly
Hi,
I have a UC540 and updated it to the latest IOS version with the latest firmware to my phones and i am having registration problems with SPA525g IP Phones. I updated the firmware of the phones as well and create manual tftp bindings with but still it is not registering. I run a couple of debugs (debug tftp events and debug ephone registration) I can see from the logs and in the phone that it is taking the proper VLAN and being discovered via CDP and being pointed to the TFTP server and still wont register. I can see that it is also taking its own .cnf file properly then the output sccp token regected invalid devices error is shown I have a SPA502G and it is working fine. Also there is a previous issue that all the voice port are shown as engage or offhook even the calls are disconnected thus make the main PSTN number busy am based in UAE and our service provider is etisalat I have check with them about the proper disconnection values but still it the same. That's why I have arrived in the conclusion to just update everything including the IOS and the phones firmware. I have put my config in this post, I am also trying to take the CCNA Voice exam on the 2nd week of april and I think that if i don't know how fix this issue for our customer then I would probably fail that exam. any suggestion and help is greatly appreciated cisco experts.
! Last configuration change at 13:36:42 ZP4 Thu Sep 13 2012 by Nick
! NVRAM config last updated at 13:45:41 ZP4 Thu Sep 13 2012 by Nick
version 15.1
parser config cache interface
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service internal
service compress-config
service sequence-numbers
hostname UC540
boot-start-marker
boot system flash:uc500-advipservicesk9-mz.151-2.T4
boot-end-marker
logging buffered 64000
enable secret 5 $1$3CIf$.rXyHeJQrwd97X/f2dS0M1
no aaa new-model
clock timezone ZP4 4 0
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-3558175224
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3558175224
revocation-check none
crypto pki certificate chain TP-self-signed-3558175224
certificate self-signed 01 nvram:IOS-Self-Sig#3.cer
dot11 syslog
dot11 ssid cisco-data
vlan 1
authentication open
dot11 ssid cisco-voice
vlan 100
authentication open
ip source-route
ip cef
ip dhcp relay information trust-all
ip dhcp excluded-address 10.1.3.1 10.1.3.10
ip dhcp pool phone
network 10.1.3.0 255.255.255.0
default-router 10.1.3.1
option 150 ip 10.1.3.1
ip name-server 213.42.20.20
ip name-server 195.229.241.222
ip inspect WAAS flush-timeout 10
ip inspect name SDM_LOW cuseeme
ip inspect name SDM_LOW dns
ip inspect name SDM_LOW ftp
ip inspect name SDM_LOW h323
ip inspect name SDM_LOW https
ip inspect name SDM_LOW icmp
ip inspect name SDM_LOW imap
ip inspect name SDM_LOW pop3
ip inspect name SDM_LOW netshow
ip inspect name SDM_LOW rcmd
ip inspect name SDM_LOW realaudio
ip inspect name SDM_LOW rtsp
ip inspect name SDM_LOW esmtp
ip inspect name SDM_LOW sqlnet
ip inspect name SDM_LOW streamworks
ip inspect name SDM_LOW tftp
ip inspect name SDM_LOW tcp router-traffic
ip inspect name SDM_LOW udp router-traffic
ip inspect name SDM_LOW vdolive
no ipv6 cef
multilink bundle-name authenticated
stcapp ccm-group 1
stcapp
stcapp supplementary-services
port 0/0/0
fallback-dn 301
port 0/0/1
fallback-dn 302
port 0/0/2
fallback-dn 303
port 0/0/3
fallback-dn 304
trunk group ALL_FXO
max-retry 5
voice-class cause-code 1
hunt-scheme longest-idle
translation-profile outgoing PROFILE_ALL_FXO
trunk group ALL_FX0
voice call send-alert
voice rtp send-recv
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
sip
no update-callerid
voice class codec 1
codec preference 1 g711alaw
codec preference 2 g711ulaw
voice class dualtone-detect-params 1
freq-max-deviation 50
freq-max-power 0
freq-min-power 13
freq-power-twist 4
cadence-variation 6
voice class custom-cptone UAE-CUSTOM
dualtone disconnect
frequency 406
cadence 398 344 237 527 400
voice class custom-cptone CCAjointone
dualtone conference
frequency 600 900
cadence 300 150 300 100 300 50
voice class custom-cptone CCAleavetone
dualtone conference
frequency 400 800
cadence 400 50 200 50 200 50
voice class cause-code 1
no-circuit
voice register global
voice hunt-group 1 parallel
list 301,302,303
timeout 24
pilot 511
voice translation-rule 4
rule 15 // //
voice translation-rule 1000
rule 1 /.*/ //
voice translation-rule 1111
voice translation-rule 1112
rule 1 /^9/ //
rule 3 /^0/ //
voice translation-rule 2222
voice translation-rule 3265
rule 1 /\(^..........$\)/ /9\1/
rule 2 /\(^.........$\)/ /9\1/
rule 15 /\(^ABCD$\)/ /ABCD\1/
voice translation-profile CALLER_ID_TRANSLATION_PROFILE
translate calling 1111
voice translation-profile CallBlocking
translate called 2222
voice translation-profile INCOMING_CallerID_PROFILE
translate calling 3265
voice translation-profile OUTGOING_TRANSLATION_PROFILE
translate called 1112
voice translation-profile PROFILE_ALL_FXO
translate calling 4
voice translation-profile nondialable
translate called 1000
voice-card 0
dspfarm
dsp services dspfarm
license udi pid UC540W-FXO-K9 sn FHK143074G6
archive
log config
logging enable
logging size 600
hidekeys
username cisco privilege 15 secret 5 $1$vjNa$OFKLhupqR8al6x2b8Xmcj/
username adminac privilege 15 secret 5 $1$NDC.$PtD0y4YGIj5SqI1gghxWE1
username Nick privilege 15 secret 5 $1$iAmL$tsg7Jf2TEND1NN.h8z2dy/
ip tftp source-interface Loopback0
bridge irb
interface Loopback0
description $FW_INSIDE$
ip address 10.1.10.2 255.255.255.252
ip access-group 101 in
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/0
description $FW_OUTSIDE$
ip address 192.168.101.2 255.255.255.252
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
interface Integrated-Service-Engine0/0
description cue is initialized with default IMAP group
ip unnumbered Loopback0
ip nat inside
ip virtual-reassembly in
service-module ip address 10.1.10.1 255.255.255.252
service-module ip default-gateway 10.1.10.2
interface FastEthernet0/1/0
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/1
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/2
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/3
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/4
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/5
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/6
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/7
switchport access vlan 20
spanning-tree portfast
interface FastEthernet0/1/8
switchport access vlan 100
macro description cisco-switch
interface Dot11Radio0/5/0
no ip address
shutdown
ssid cisco-data
ssid cisco-voice
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
interface Dot11Radio0/5/0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0/5/0.100
encapsulation dot1Q 100
bridge-group 100
bridge-group 100 subscriber-loop-control
bridge-group 100 spanning-disabled
bridge-group 100 block-unknown-source
no bridge-group 100 source-learning
no bridge-group 100 unicast-flooding
interface Vlan1
no ip address
bridge-group 1
bridge-group 1 spanning-disabled
interface Vlan20
ip address 10.10.10.1 255.255.255.0
interface Vlan100
no ip address
bridge-group 100
bridge-group 100 spanning-disabled
interface BVI1
description $FW_INSIDE$
no ip address
ip nat inside
ip virtual-reassembly in
shutdown
interface BVI100
description $FW_INSIDE$
ip address 10.1.3.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http path flash:/gui
ip dns server
ip nat inside source list 1 interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 192.168.101.1
ip route 10.1.10.1 255.255.255.255 Integrated-Service-Engine0/0
logging esm config
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 192.168.10.0 0.0.0.255
access-list 1 permit 10.1.3.0 0.0.0.255
access-list 1 permit 10.1.10.0 0.0.0.3
access-list 100 remark auto generated by SDM firewall configuration
access-list 100 remark SDM_ACL Category=1
access-list 100 deny ip 192.168.10.0 0.0.0.255 any
access-list 100 deny ip host 255.255.255.255 any
access-list 100 deny ip 127.0.0.0 0.255.255.255 any
access-list 100 permit ip any any
access-list 101 remark auto generated by SDM firewall configuration##NO_ACES_8##
access-list 101 remark SDM_ACL Category=1
access-list 101 permit tcp 10.1.3.0 0.0.0.255 eq 2000 any
access-list 101 permit udp 10.1.3.0 0.0.0.255 eq 2000 any
access-list 101 deny ip 10.1.3.0 0.0.0.255 any
access-list 101 deny ip 192.168.10.0 0.0.0.255 any
access-list 101 deny ip 192.168.101.0 0.0.0.3 any
access-list 101 deny ip host 255.255.255.255 any
access-list 101 deny ip 127.0.0.0 0.255.255.255 any
access-list 101 permit ip any any
access-list 102 remark auto generated by SDM firewall configuration##NO_ACES_6##
access-list 102 remark SDM_ACL Category=1
access-list 102 deny ip 10.1.10.0 0.0.0.3 any
access-list 102 deny ip 10.1.3.0 0.0.0.255 any
access-list 102 deny ip 192.168.101.0 0.0.0.3 any
access-list 102 deny ip host 255.255.255.255 any
access-list 102 deny ip 127.0.0.0 0.255.255.255 any
access-list 102 permit ip any any
access-list 102 permit ip 192.168.101.0 0.0.0.3 any
access-list 103 remark auto generated by SDM firewall configuration##NO_ACES_8##
access-list 103 remark SDM_ACL Category=1
access-list 103 permit tcp 10.1.10.0 0.0.0.3 any eq 2000
access-list 103 permit udp 10.1.10.0 0.0.0.3 any eq 2000
access-list 103 deny ip 10.1.10.0 0.0.0.3 any
access-list 103 deny ip 192.168.10.0 0.0.0.255 any
access-list 103 deny ip 192.168.101.0 0.0.0.3 any
access-list 103 deny ip host 255.255.255.255 any
access-list 103 deny ip 127.0.0.0 0.255.255.255 any
access-list 103 permit ip any any
access-list 105 permit ip any any
snmp-server community public RO
tftp-server flash:/phones/521_524/cp524g-8-1-17.bin alias cp524g-8-1-17.bin
tftp-server flash:/phones/5x5/spa5x5-7-1-3c.bin alias spa5x5-7-1-3c.bin
tftp-server flash:/phones/525/spa525g-7-4-8.bin alias spa525g-7-4-8.bin
control-plane
bridge 1 route ip
bridge 100 route ip
voice-port 0/0/0
cptone GB
station-id name Cordless
station-id number 329
caller-id enable
voice-port 0/0/1
cptone AE
caller-id enable
voice-port 0/0/2
cptone AE
caller-id enable
voice-port 0/0/3
cptone AE
caller-id enable
voice-port 0/1/0
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4FXO-0/1/0-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/1/1
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4 FXO-0/1/1-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/1/2
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
supervisory dualtone-detect-params 1
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4 FXO-0/1/2-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/1/3
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4 FXO-0/1/3-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/4/0
auto-cut-through
signal immediate
input gain auto-control -15
description Music On Hold Port
sccp local Loopback0
sccp ccm 10.1.3.1 identifier 1 version 4.0
sccp
sccp ccm group 1
associate ccm 1 priority 1
associate profile 1 register confprof1
dspfarm profile 1 conference
description DO NOT MODIFY, active CCA conference profile - CCA2.0 codec729
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP
dial-peer cor custom
name internal
name local
name local-plus
name international
name national
name national-plus
name emergency
name toll-free
dial-peer cor list call-internal
member internal
dial-peer cor list call-local
member local
dial-peer cor list call-local-plus
member local-plus
dial-peer cor list call-national
member national
dial-peer cor list call-national-plus
member national-plus
dial-peer cor list call-international
member international
dial-peer cor list call-emergency
member emergency
dial-peer cor list call-toll-free
member toll-free
dial-peer cor list user-internal
member internal
member emergency
dial-peer cor list user-local
member internal
member local
member emergency
member toll-free
dial-peer cor list user-local-plus
member internal
member local
member local-plus
member emergency
member toll-free
dial-peer cor list user-national
member internal
member local
member local-plus
member national
member emergency
member toll-free
dial-peer cor list user-national-plus
member internal
member local
member local-plus
member national
member national-plus
member emergency
member toll-free
dial-peer cor list user-international
member internal
member local
member local-plus
member international
member national
member national-plus
member emergency
member toll-free
dial-peer voice 1 pots
port 0/0/0
no sip-register
dial-peer voice 2 pots
port 0/0/1
no sip-register
dial-peer voice 3 pots
port 0/0/2
no sip-register
dial-peer voice 4 pots
port 0/0/3
no sip-register
dial-peer voice 5 pots
description ** MOH Port **
destination-pattern ABC
port 0/4/0
no sip-register
dial-peer voice 50 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/0
dial-peer voice 51 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/1
dial-peer voice 52 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/2
dial-peer voice 53 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/3
dial-peer voice 54 pots
description ** FXO pots dial-peer **
destination-pattern A0
port 0/1/0
no sip-register
dial-peer voice 55 pots
description ** FXO pots dial-peer **
destination-pattern A1
port 0/1/1
no sip-register
dial-peer voice 56 pots
description ** FXO pots dial-peer **
destination-pattern A2
port 0/1/2
no sip-register
dial-peer voice 2000 voip
description ** cue voicemail pilot number **
destination-pattern 388
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 6 pots
description "catch all dial peer for BRI/PRI"
translation-profile incoming nondialable
incoming called-number .%
direct-inward-dial
dial-peer voice 57 pots
description ** FXO pots dial-peer **
destination-pattern A3
port 0/1/3
no sip-register
dial-peer voice 69 pots
destination-pattern 329
port 0/0/0
dial-peer voice 300 pots
trunkgroup ALL_FX0
description Local Numbers
destination-pattern 9T
forward-digits 9
dial-peer voice 301 voip
destination-pattern 2..
session target ipv4:192.168.201.2
dial-peer voice 303 pots
trunkgroup ALL_FXO
trunkgroup ALL_FX0
description **InternationalCall**
destination-pattern 88T
dial-peer voice 304 pots
trunkgroup ALL_FX0
description *EM1*
destination-pattern 9[1-9]T
forward-digits 3
dial-peer voice 302 pots
trunkgroup ALL_FX0
description **Mobiles**
destination-pattern 9.[0-9].[0-9]......
dial-peer voice 305 pots
trunkgroup ALL_FX0
description **800-**
destination-pattern 9[0-9][0-9][0-9]T
no dial-peer outbound status-check pots
telephony-service
sdspfarm conference mute-on 111 mute-off 222
sdspfarm units 5
sdspfarm tag 1 confprof1
conference hardware
video
fxo hook-flash
max-ephones 40
max-dn 300
ip source-address 10.1.3.1 port 2000
max-redirect 20
auto assign 1 to 1 type bri
calling-number initiator
service phone videoCapability 1
service phone webAccess 0
service dnis overlay
service dnis dir-lookup
timeouts interdigit 5
system message American Center
url services http://10.1.10.1/voiceview/common/login.do
url authentication http://10.1.10.2/CCMCIP/authenticate.asp
load 521G-524G cp524g-8-1-17
load 525G spa525g-7-4-8
load 501G spa5x5-7-1-3c
load 502G spa5x5-7-1-3c
load 504G spa5x5-7-1-3c
load 508G spa5x5-7-1-3c
load 509G spa5x5-7-1-3c
time-zone 35
date-format dd-mm-yy
voicemail 388
max-conferences 8 gain -6
call-forward pattern .T
call-forward system redirecting-expanded
hunt-group logout HLog
moh MOH2.wav
multicast moh 239.10.16.16 port 2000
web admin system name cisco secret 5 $1$iDgA$MKNi2RWfsO0KjuC82kgLJ1
dn-webedit
time-webedit
transfer-system full-consult dss
transfer-pattern 9.T
transfer-pattern .T
secondary-dialtone 9
fac standard
create cnf-files version-stamp 7960 Aug 29 2012 12:00:04
line con 0
privilege level 15
logging synchronous
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
exec-timeout 0 0
logging synchronous
login local
transport input all
line vty 5 100
login local
transport input all
ntp master
end
Some of the output are not shown becaus it is to long I have attach the whole config for reference and any advice on how could I optimize and resolve my issues is greatly appreciated. ThanksNicolo - First off this stuff gets crazy sometimes. No worries about the exam. Sometimes when FXO ports go crazy it is due to battery reversal. If you go to the FXO port settings try turning battery reversal on and or off... depending on its current setting. See if that helps.
As for the 525s not registering.. These are inside the network correct? Are you connecting one directly to the UC500 with a Cat5E or Cat6 patch cable and the same thing happens? Does the MAC address on the phone match a MAC address under the EPHONE settings?
If you telnet into the UC500 can you execute a "dir" command at the CLI prompt and "CD" (change directory) into the phones folder and then the spa525g folder? Do files exist in there?
Also I only see an IP address under BVI100? This is the voice side of things what happened to the IP address under BVI1 (Data VLAN). Can you give us some information about the internal network? Cna you PING this phone system from the network? What IP address does it have? -
we have 2801 router that connected with 2 anloga lines (FXO Card), but now we have a problem with disconnect problem, the phone still connected after the PSTN Caller Disconnect, and our policy tell that the agents shouldn't end the call, so we want when the PSTN caller end the call we need the phone to return to idle state.
and according for the below link, i configure the custom disconnect tone, and in the attachment you can find tow disconnect tones.
http://ciscoflair.blogspot.com/2009/05/cisco-fxo-disconnect-issue.html
the configuration of the custom disconnect tone
voice class dualtone-detect-params 1
cadence-variation 3
voice class custom-cptone Custom1
dualtone disconnect
frequency 420
cadence 245 255 245 255 245 255
and the below you can find the configuration of the voice port, and you can find the debug vpm port 0/3/0, debug vpm signal, for a call that disconnected immediately, and for a call the take long time to disconnected.
this is the configuration of the voice port:
voice-port 0/3/0
supervisory disconnect dualtone mid-call
supervisory custom-cptone Custom1
supervisory dualtone-detect-params 1
no battery-reversal
cptone NL
timeouts call-disconnect 5
timeouts wait-release 5
timing hookflash-out 50
timing guard-out 300
caller-id enable
caller-id alerting line-reversal
caller-id alerting dsp-pre-allocate
this is the debug of a call that is disconnected immediately:
Jan 25 11:48:32.262: [0/3/0] htsp_dsm_feature_notify_cb returns 2 id=DSM_FEATURE_SM_CALLERID_RX
Jan 25 11:48:32.262: htsp_process_event: [0/3/0, FXOLS_ONHOOK, E_HTSP_CALLERID_RX_DONE]
Jan 25 11:48:32.262: [0/3/0] htsp_stop_caller_id_rx. message length 11
Jan 25 11:48:32.262: [0/3/0] htsp_dsm_close_done
Jan 25 11:48:34.026: htsp_process_event: [0/3/0, FXOLS_ONHOOK, E_DSP_SIG_0000]fxols_onhook_ringing
Jan 25 11:48:34.026: htsp_timer - 125 msec
Jan 25 11:48:34.154: htsp_process_event: [0/3/0, FXOLS_WAIT_RING_MIN, E_HTSP_EVENT_TIMER]fxols_wait_ring_min_timer
Jan 25 11:48:34.154: htsp_timer - 10000 msec
Jan 25 11:48:35.305: htsp_process_event: [0/3/0, FXOLS_RINGING, E_DSP_SIG_0100]
Jan 25 11:48:35.305: fxols_ringing_not
Jan 25 11:48:35.305: htsp_timer_stop
Jan 25 11:48:35.305: htsp_timer_stop3 htsp_setup_ind
Jan 25 11:48:35.305: [0/3/0] get_fxo_caller_id:Caller ID received. Message type=129 length=11 checksum=00
Jan 25 11:48:35.309: [0/3/0] Caller ID String 44 30 36 35 36 37 39 31 34 31
Jan 25 11:48:35.309: [0/3/0] get_fxo_caller_id calling num=065679141 calling name= calling time=01/25 13:48
Jan 25 11:48:35.313: htsp_process_event: [0/3/0, FXOLS_WAIT_SETUP_ACK, E_HTSP_SETUP_ACK]
Jan 25 11:48:35.313: fxols_wait_setup_ack:
Jan 25 11:48:35.313: [0/3/0] set signal state = 0xC timestamp = 0fxols_check_auto_call
Jan 25 11:48:35.321: htsp_process_event: [0/3/0, FXOLS_PROCEEDING, E_HTSP_PROCEEDING]fxols_offhook_proc
Jan 25 11:48:35.321: htsp_timer - 120000 msechtsp_alert_notify
Jan 25 11:48:35.389: htsp_process_event: [0/3/0, FXOLS_PROCEEDING, E_HTSP_ALERT]fxols_offhook_alerthtsp_call_service_msghtsp_call_service_msg not EFXS (2)
Jan 25 11:48:35.509: htsp_call_bridged invokedhtsp_call_service_msghtsp_call_service_msg not EFXS (2)
Jan 25 11:48:35.513: htsp_process_event: [0/3/0, FXOLS_PROCEEDING, E_HTSP_CONNECT]fxols_offhook_connect
Jan 25 11:48:35.513: htsp_timer_stop
Jan 25 11:48:35.521: htsp_process_event: [0/3/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
Jan 25 11:48:35.585: htsp_process_event: [0/3/0, FXOLS_CONNECT, E_DSP_SIG_0110]fxols_rvs_battery
Jan 25 11:48:35.585: htsp_timer_stop2
sh voice po su
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
=============== == ============ ===== ==== ======== ======== ==
0/3/0 -- fxo-ls up up idle off-hook y
0/3/1 -- fxo-ls up dorm idle on-hook y
50/0/1 1 efxs up up on-hook idle y
50/0/1 2 efxs up up on-hook idle y
PWR FAILOVER PORT PSTN FAILOVER PORT
================= ==================
Jan 25 11:48:43.857: htsp_process_event: [0/3/0, FXOLS_CONNECT, E_DSP_SUP_DISCONNECT]fxols_conn_sup_disc
Jan 25 11:48:43.857: htsp_timer2 - 5000 msec
Madaba_Maint#
Jan 25 11:48:48.856: htsp_process_event: [0/3/0, FXOLS_CONNECT, E_HTSP_EVENT_TIMER2]fxols_disc_confirm
Jan 25 11:48:48.856: htsp_timer_stop
Jan 25 11:48:48.856: htsp_timer_stop2
Jan 25 11:48:48.856: htsp_timer_stop3
Jan 25 11:48:48.860: htsp_timer_stop3
Jan 25 11:48:48.876: htsp_process_event: [0/3/0, FXOLS_REMOTE_RELEASE, E_HTSP_RELEASE_REQ]fxols_offhook_release
Jan 25 11:48:48.876: htsp_timer_stop
Jan 25 11:48:48.876: htsp_timer_stop2
Jan 25 11:48:48.876: htsp_timer_stop3
Jan 25 11:48:48.876: [0/3/0] set signal state = 0x4 timestamp = 0
Jan 25 11:48:48.876: htsp_timer - 300 msec
Jan 25 11:48:49.148: htsp_process_event: [0/3/0, FXOLS_GUARD_OUT, E_DSP_SIG_0110]
Jan 25 11:48:49.176: htsp_process_event: [0/3/0, FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER]fxols_guard_out_timeout
Jan 25 11:48:49.176: fxols_dsp_prealloc_clid_wait. Line reversal alerting DSP preallocation done
Jan 25 11:48:49.176: [0/3/0] htsp_start_caller_id_rx:ETSI_DTMF
Jan 25 11:48:49.176: htsp_start_caller_id_rx create dsp_stream_manager
Jan 25 11:48:49.176: htsp_process_event: [0/3/0, FXOLS_ONHOOK, E_DSP_SIG_0100]
Jan 25 11:48:49.176: [0/3/0] htsp_dsm_create_success returns 1
Madaba_Maint#sh voice po su
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
=============== == ============ ===== ==== ======== ======== ==
0/3/0 -- fxo-ls up dorm idle on-hook y
0/3/1 -- fxo-ls up dorm idle on-hook y
50/0/1 1 efxs up up on-hook idle y
50/0/1 2 efxs up up on-hook idle y
this is a debug for a call that is take a long time to disconnected:
Jan 25 11:49:42.267: [0/3/0] htsp_dsm_feature_notify_cb returns 2 id=DSM_FEATURE_SM_CALLERID_RX
Jan 25 11:49:42.267: htsp_process_event: [0/3/0, FXOLS_ONHOOK, E_HTSP_CALLERID_RX_DONE]
Jan 25 11:49:42.267: [0/3/0] htsp_stop_caller_id_rx. message length 11
Jan 25 11:49:42.271: [0/3/0] htsp_dsm_close_done
Jan 25 11:49:43.999: htsp_process_event: [0/3/0, FXOLS_ONHOOK, E_DSP_SIG_0000]fxols_onhook_ringing
Jan 25 11:49:43.999: htsp_timer - 125 msec
Jan 25 11:49:44.127: htsp_process_event: [0/3/0, FXOLS_WAIT_RING_MIN, E_HTSP_EVENT_TIMER]fxols_wait_ring_min_timer
Jan 25 11:49:44.127: htsp_timer - 10000 msec
Jan 25 11:49:45.279: htsp_process_event: [0/3/0, FXOLS_RINGING, E_DSP_SIG_0100]
Jan 25 11:49:45.279: fxols_ringing_not
Jan 25 11:49:45.279: htsp_timer_stop
Jan 25 11:49:45.279: htsp_timer_stop3 htsp_setup_ind
Jan 25 11:49:45.279: [0/3/0] get_fxo_caller_id:Caller ID received. Message type=129 length=11 checksum=00
Jan 25 11:49:45.279: [0/3/0] Caller ID String 44 30 36 35 36 37 39 31 34 31
Jan 25 11:49:45.279: [0/3/0] get_fxo_caller_id calling num=065679141 calling name= calling time=01/25 13:49
Jan 25 11:49:45.283: htsp_process_event: [0/3/0, FXOLS_WAIT_SETUP_ACK, E_HTSP_SETUP_ACK]
Jan 25 11:49:45.283: fxols_wait_setup_ack:
Jan 25 11:49:45.287: [0/3/0] set signal state = 0xC timestamp = 0fxols_check_auto_call
Jan 25 11:49:45.291: htsp_process_event: [0/3/0, FXOLS_PROCEEDING, E_HTSP_PROCEEDING]fxols_offhook_proc
Jan 25 11:49:45.291: htsp_timer - 120000 msechtsp_alert_notify
Jan 25 11:49:45.379: htsp_process_event: [0/3/0, FXOLS_PROCEEDING, E_HTSP_ALERT]fxols_offhook_alerthtsp_call_service_msghtsp_call_service_msg not EFXS (2)
Jan 25 11:49:45.495: htsp_call_bridged invokedhtsp_call_service_msghtsp_call_service_msg not EFXS (2)
Jan 25 11:49:45.503: htsp_process_event: [0/3/0, FXOLS_PROCEEDING, E_HTSP_CONNECT]fxols_offhook_connect
Jan 25 11:49:45.503: htsp_timer_stop
Jan 25 11:49:45.507: htsp_process_event: [0/3/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
Jan 25 11:49:45.559: htsp_process_event: [0/3/0, FXOLS_CONNECT, E_DSP_SIG_0110]fxols_rvs_battery
Jan 25 11:49:45.559: htsp_timer_stop2
sh voice po su
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
=============== == ============ ===== ==== ======== ======== ==
0/3/0 -- fxo-ls up up idle off-hook y
0/3/1 -- fxo-ls up dorm idle on-hook y
50/0/1 1 efxs up up on-hook idle y
50/0/1 2 efxs up up on-hook idle y
Jan 25 11:50:30.387: htsp_timer_stop3
Jan 25 11:50:30.399: htsp_process_event: [0/3/0, FXOLS_CONNECT, E_HTSP_RELEASE_REQ]fxols_offhook_release
Jan 25 11:50:30.399: htsp_timer_stop
Jan 25 11:50:30.399: htsp_timer_stop2
Jan 25 11:50:30.399: htsp_timer_stop3
Jan 25 11:50:30.399: [0/3/0] set signal state = 0x4 timestamp = 0
Jan 25 11:50:30.399: htsp_timer - 300 msec
Jan 25 11:50:30.671: htsp_process_event: [0/3/0, FXOLS_GUARD_OUT, E_DSP_SIG_0110]
Jan 25 11:50:30.699: htsp_process_event: [0/3/0, FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER]fxols_guard_out_timeout
Jan 25 11:50:30.699: fxols_dsp_prealloc_clid_wait. Line reversal alerting DSP preallocation done
Jan 25 11:50:30.699: [0/3/0] htsp_start_caller_id_rx:ETSI_DTMF
Jan 25 11:50:30.699: htsp_start_caller_id_rx create dsp_stream_manager
Jan 25 11:50:30.699: htsp_process_event: [0/3/0, FXOLS_ONHOOK, E_DSP_SIG_0100]
Jan 25 11:50:30.699: [0/3/0] htsp_dsm_create_success returns 1
So what can we do? what is the wronge of my configuration?anyone can help?
-
Hi All,
I have an issue with call disconnect on FXO port. Call are getting disconnected as soon as it connects.
I observed the call takes the port 0/20 which has the command supervisory disconnect anytone
but in other ports I see supervisory disconnect dualtone mid-call
so I have changed with the second and got it working for some calls, In the debug vpm singal debugs I see remote device releases the call.
Could you tell me how this works and what are the debugs we could check to see what is the exact problem?
Number dialled are : 361000, 352788
Can you check? Logs and sh run is attached.
Thanks,
Lajith PBeside that what you said Laith - I still think that you need specific tones for disconnect on FXO and only then your voice setup is going to work as it should. I can't comment on different version of IOS-es but maybe your previous one was better in handling this type of problem...if you don't have any specific requirement and must use 15.1 IOS you can always revert back to 15.0 and continue using your ports as already...
But if I was on your place - I would solve this problem once for all and then you don't have to worry about some upcoming new IOS
HTH,
Dragan -
Need a sample cme with multiple fxo ports, hunt fashion
hi,
anyone kind enough to provide a sample working configuration of multiple fxo ports (each being a pstn line) and I assuming the telco is doing hunting...
so let's say 4 lines, if line 1 is busy the call is sent by the telco on line 2 and so on...
incoming and outgoing.
thank you very much!!
I did google it and can't find anything with multiple fxo ports.trunk group 1
max-calls voice 4 (or however many POTS lines you want to use)
hunt-scheme round-robin (or whatever method you like)
voice-port 0/0/0
trunk-group 1
connection plar opx XXXX (extension)
caller-id enable
voice-port 0/0/1
trunk-group 1
connection plar opx XXXX
caller-id enable
voice-port 0/0/2
trunk-group 1
connection plar opx XXXX
caller-id enable
voice-port 0/0/3
trunk-group 1
connection plar opx XXXX
caller-id enable
dial-peer voice 1 pots ( I like creating this for troubleshooting, by default cisco router accept incoming calls)
trunkgroup 1
incoming called-number .
direct-inward-dial
dial-peer voice 2 pots
trunkgroup 1
destination-pattern 8[2-9]...... (8 for an outside line or 9 or nothing, then adjust your forward-digits to match)
forward-digits 7
dial-peer voice 3 pots
trunkgroup 1
destination-pattern 81[2-9]..[2-9]......
forward-digits 11
dial-peer voice 4 pots
trunkgroup 1
destination-pattern 8911
forward-digits 3
dial-peer voice 5 pots
trunkgroup 1
destination-pattern 911
forward-digits 3 -
I need a sample config for a 2650XM with FXO ports that will be used to route incoming calls to a particular group and that same group will be making calls out that same gateway. I am on CCM 3.3(3)sr3.
If anyone can help me or point me to documentation that would help I would greatly appreciate it.Here is some information -
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a0080094636.shtml
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_configuration_example09186a0080094852.shtml
For a basic H323 gateway, the following would work :
interface ethernet 0/0
ip address 100.1.1.1 255.255.255.0
h323-gateway voip bind srcaddr 100.1.1.1
voice-port 1/0/0
description - fxo to Call manager
connection plar opx 1000
dial-peer voice 1 voip
description - VOIP calls to call manager
destination-pattern 1000
session target ipv4:100.1.1.100
codec g711ulaw
dtmf-relay h245-alphanumeric
ip precedence 5
dial-peer 10 pots
destination-pattern 0
port 1/0/0
Create a H323 gateway in the CM config and give it the name of the router's ethernet IP address.
Create a route pattern of 0.XXXXXXXX where the XXXX's represent the digit string to send out to the PSTN , so each X represents a unique digit.
Point the route pattern to the H323 gateway , and under called party transforms set the discard digits to none, so the called number that hits the gateway router is prepended with a 0. This 0 will be stripped off by the router POTS dial peer, but it will leave the rest of the string intact. -
Cisco UC 520 FXO port, dual or single line?
I am needing to configure the FXO ports on a UC 520 to accept 2 numbers instead of just 1, is this possible?
timer media-inactive To enable the timer for media inactivity detection using the digital signal processor (DSP) (based on RTP as the only criterion) and to configure a multiplication factor based on the real-time control protocol (RTCP) timer interval, use the timer media-inactive command in gateway configuration mode. To reset to the default, use the no form of this command. timer media-inactive multiple no timer media-inactive multiple
When the timer media-inactive command is used, the gateway uses the inactivity timer as a combination of the timer media-inactive command and the ip rtcp report interval command. The timer media-inactive command uses DSP statistics. This capability is based on the configuration of callfeature parameters using application command-line interface (CLI) to enable control. The media are considered inactive only if there is no transfer of RTP packets in the send direction and no RTP packets in the receive direction. If RTP is present in either the send or receive direction, it is considered active. In this mode, DSP filters out any comfort noise packets, and the presence of any comfort noise packet is considered inactivity in either direction. The multiple argument (or multiplication factor) is multiplied by the interval that is set using the ip rtcp report interval command. This command configures the average interval between successive RTCP report transmissions for a given voice session. For example, if the value argument is set to 25,000 milliseconds, an RTCP report is sent every 25 seconds, on average. If no RTP packets are received during the calculated interval, the call is disconnected. The gateway signals the disconnect to the VoIP network and the time-division multiplexing (TDM) network so that upstream and downstream devices can clear their resources.
Sent from Cisco Technical Support iPad App -
Airport Extreme dropping connection with a Cisco 5 port Giga switch
I've connected a Cisco 5 port Giga switch SG100D-05 to one of the LAN ports of the Airport Extreme and for some reason the connection is being dropped or it fails to connect. Any idea of why this is happening and how can it be fixed?
If you have not already done so, you might want to do some basic troubleshooting to try to isolate the cause of the issue.
To do that, temporarily disconnect the switch and power it off. Connect a computer with an Ethernet port on it to the LAN port on AirPort Extreme and turn off the wireless on the computer.
Test to see you can get a good Internet connection this way.
If you can, then you know that the LAN port on the AirPort Extreme is functioning correctly and your troubleshooting efforts will need to focus on testing each port on the Cisco switch.
If you cannot get a good connection with the computer connected directly to the AirPort Extreme, try another Ethernet cable that you know is working to eliminate the possibility of a bad Ethernet cable, which is the culprit more often than you might think.
Please post back on the results of your testing. -
Configuring Paging system to interface with an FXO port
Hello
Wanted to see if there is some good documentation on configuring my fxo port on my gateway to interface with a paging system?
Thank you for your helpHi Joseph,
It really depends on the type of overhead paging system you're intending to use. The documentation for the paging system being used usually specifies exactly what type of circuit is required.
Kind regards,
Craig -
Partitioning FXO port for different users on Cisco CME 2911or UC540
Hello,
we have 10 users in our network and we have 4 FXO port and lines connected to them, we would like to implement this requirement on our network below;
2 users will have access to FXO port 1
3 users will have access to FXO port 2
3 users will have access to FXO port 3
2 users will have access to FXO port 4
please, i have searched for the features on UC540 but no avail, everyone is going out on all port but i only want 2 users to be able to access a port then others should not.
please, how do i archieve this.
please, replyYou would need something called Class of Restriction.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeadm/cmeblock.html#65477
Basically, you put "locks" on your outgoing dial-peers which are referencing your analog ports, and then you give certain "keys" to the directory numbers you wish to unlock those locks. -
Cisco Catalyst 4507R+E with WS-X4748 blade, ports not working
I have a Cisco Catalyst 4507R+E (with Sup7-E) and two blades; one WS-X4748-RJ45V+E and one WS-X4648-RJ45-E.
When I connect a device to a port on the WS-X4748-RJ45V+E blade the port will not come up, show interface shows the status as "notconnect". When I connect the same device to the WS-X4648-RJ45-E blade the interface comes up.
The WS-X4748-RJ45V+E blade seems to have initialised okay, it appears in the output of "show module" as OK.
I get exactly the same effect on a second, identically configured Catalyst 4507R+E.
The software version is IOS XE 3.1.0SG, which according to the release notes supports the WS-X4748-RJ45V+E blade. Has anybody else seen anything like this?I have 2 Core switches, single SUP on each.
Line cards #1 and #2 randomly stop forwarding packets, only solution is to reload the switch ( hw-module reset does not work ). I have cat4500e-universalk9.SPA.03.05.00.E.152-1.E.bin and the sympton looks the same as the described one,
although the code is newer than 3.2.2SG.
Now we are downgrading to cat4500e-universalk9.SPA.03.04.02.SG.151-2.SG2.bin to check if that solves the issue,
otherwise we´ll try removing/re-inserting the modules, and if issue persists, most probably RMA the Core1.
We´ve sent a show tech to Cisco support while the issue was happening.
Current modules on the Core switches.
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 48 10/100/1000BaseT EEE (RJ45) WS-X4748-RJ45-E CAT1627L48B
2 48 10/100/1000BaseT EEE (RJ45) WS-X4748-RJ45-E CAT1629L0ZY
3 4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7-E CAT1629L1PD
5 12 1000BaseX (SFP) WS-X4612-SFP-E JAE163007EO
M MAC addresses Hw Fw Sw Status
--+--------------------------------+---+------------+----------------+---------
1 30f7.0d57.80c0 to 30f7.0d57.80ef 1.1 Ok
2 30f7.0dac.fd40 to 30f7.0dac.fd6f 1.1 Ok
3 30f7.0dca.6c00 to 30f7.0dca.6c03 2.1 15.0(1r)SG10 03.05.00.E Ok
5 a493.4c44.13e8 to a493.4c44.13f3 1.1 Ok
Mod Redundancy role Operating mode Redundancy status
----+-------------------+-------------------+----------------------------------
3 Active Supervisor SSO Active -
How to check UC560 FXO Port Not Problem Question
Dear All,
We are newbie on Cisco UC560.
Our customer use Cisco UC560, ESW-520-24P and Cisco SPA 502G and 508G for their branch office replace old traditional PBX. Cisco UC560 have built-in VIC2-4FXO and VIC2-4FXS.
Our customer PSTN line connected to UC560 FXO port (1 line PSTN).
We receive report from our customer that they cannot make a call to PSTN and receive call from PSTN that connected to UC560 FXO port (on physical FXO port LED Green turn on). When the problem happen our customer has restart UC560 or shutdown FXO port from CLI.
We have do some test to our customer UC560.
- Moving PSTN line to another FXO port (example: port from 0/1/0 to 0/1/1). The result is same (cannot make call to PSTN and receive call from PSTN)
Today, We have checked on our customer UC560 via show voice port summary and found that port0/1/2 and 0/1/3 OPER status is up wihout cable connected to this port.
Our question:
- What command on UC560 to make sure FXO port on UC560 doesn't have problem?
We attach:
show tech-support voice
show tech-support
We hope you can give us information about this.
Thanks For Your AttentionHi There,
If you cannot find the Indonesian "Disconnect Supervision" you may get away with using Singapores "Disconnect Supervision" as your carrier networks are similar to each other
Cheers,
David Trad. -
hi,
I have a 2801 CME and 2 fxo lines. Some times when both lines are seized (because of incoming and outgoing call) and after the phones are on hook the lines are still seized and are not released and when i removed the cables from fxo port, the led on each port start to blink in sequence and then when i reconnected, the port was busy again.. so i had to reboot the router to make it work. i changed the slot but dont think that it will cause any difference..do i need to upgrade the ios or some other issue..when i am calling the disconnect is fine but it happens some time when the line get stuck i have to reboot the router. one more thing when i changed the slot of the card the router didnt detected the change of slot and was showing fxo port on old slot. i rebooted the router to detect the fxo card on the right slot..sorry for the double post but no body was replying to i post it again..
Currently Being Moderated
May 12, 2012 11:49 AM (in response to Naresh Rathore)
FXO lines stuck/hang (2801 CME)
hi following is the sh run and sh version. cme output portion is removed
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.02.03 14:27:39 =~=~=~=~=~=~=~=~=~=~=~=
User Access Verification
Username: admin
Password:
Router_Home>en
Password:
Router_Home#term
Router_Home#terminal le
Router_Home#terminal length n 512
Router_Home#sh run
Building configuration...
Current configuration : 15203 bytes
! Last configuration change at 14:41:02 UTC Thu Feb 3 2011 by admin
! NVRAM config last updated at 14:38:09 UTC Thu Feb 3 2011 by admin
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router_Home
boot-start-marker
boot-end-marker
enable password cisco
no aaa new-model
clock calendar-valid
crypto pki trustpoint TP-self-signed-2416845307
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2416845307
revocation-check none
rsakeypair TP-self-signed-2416845307
crypto pki certificate chain TP-self-signed-2416845307
certificate self-signed 01
30820243 308201AC A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 32343136 38343533 3037301E 170D3131 30323032 31373332
34335A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D32 34313638
34353330 3730819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100DFAC E4312F46 0F2BF242 E55FE0C1 73DC95F2 B2844295 DA691CE3 D9A202B1
77B1B0C3 5AE3D936 C4D786DB 7CFA6624 024C6A82 A29B3AAC 3BA89A77 5425A97A
6D79A88A C1327171 C88AA5E0 AB52F461 87FB472E A7622955 17C8F22C 58842EF4
4DFA422A 54E6B96A FA536C59 BD93FDCD 872C0586 08117535 2D13F1E0 A53E65AB
FE470203 010001A3 6B306930 0F060355 1D130101 FF040530 030101FF 30160603
551D1104 0F300D82 0B526F75 7465725F 486F6D65 301F0603 551D2304 18301680
14E940B0 E437790B 4B825CD2 0FA9020F 63C9ED3A ED301D06 03551D0E 04160414
E940B0E4 37790B4B 825CD20F A9020F63 C9ED3AED 300D0609 2A864886 F70D0101
04050003 8181006B D6136D19 6EF4DDCD B3AF591E 57B9B831 79578799 03862FCF
4AF772DE AC72FC85 3F6B6B20 81F528F0 F7B2CBD0 E9795060 C46AB102 AE2CDF53
11C39D67 B49A7AE8 FB619A0F 525543F7 8BA1D52C CABEFFEB 9E5EC7E7 938AA602
84F1ECD2 303E8609 A9AB0699 9078051B 1853BC9A 4B45F2A2 204310D5 8B34B5DD
2FA51064 EFF5D4
quit
dot11 syslog
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.168.0.1
ip dhcp excluded-address 10.168.0.2
ip dhcp excluded-address 10.168.10.1
ip dhcp excluded-address 10.168.10.2
ip dhcp excluded-address 10.168.111.1 10.168.111.6
ip dhcp pool Data
network 10.168.0.0 255.255.255.0
default-router 10.168.0.1
option 150 ip 10.168.10.1
dns-server 212.72.1.186 212.72.23.4
ip dhcp pool VOICE
network 10.168.10.0 255.255.255.0
default-router 10.168.10.1
option 150 ip 10.168.10.1
ip dhcp pool WLAN
network 10.168.111.0 255.255.255.0
default-router 10.168.111.1
option 150 ip 10.168.10.1
dns-server 212.72.1.186 212.72.23.4
ip host members.dyndns.org 204.13.248.112
ip name-server 212.72.1.186
ip name-server 212.72.23.4
ip ddns update method example_dyndns
HTTP
add http://whatisthis:[email protected]/nic/update?system=dyndns&hostname=<h>&myip=<a>
interval maximum 28 0 0 0
interval minimum 28 0 0 0
multilink bundle-name authenticated
voice-card 0
dsp services dspfarm
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
no supplementary-service h450.2
no supplementary-service h450.3
supplementary-service h450.12
h323
sip
registrar server expires max 600 min 60
username xxxxx password 0 xxxx
archive
log config
hidekeys
interface FastEthernet0/0
no ip address
ip nat inside
ip virtual-reassembly
speed auto
full-duplex
no keepalive
interface FastEthernet0/0.2
description ***** Voice LAN ******
encapsulation dot1Q 2
ip address 10.168.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface FastEthernet0/0.3
description ***** Data LAN ******
encapsulation dot1Q 3
ip address 10.168.0.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface FastEthernet0/0.4
description ***** Wireless LAN ******
encapsulation dot1Q 4
ip address 10.168.111.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface FastEthernet0/1
description $ES_WAN$
no ip address
shutdown
duplex auto
speed auto
interface ATM0/1/0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
interface ATM0/1/0.1 point-to-point
pvc 0/35
pppoe-client dial-pool-number 1
interface Dialer0
no ip address
interface Dialer1
mtu 1492
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1452
ip nat outside
ip virtual-reassembly
encapsulation ppp
ip route-cache flow
ip tcp adjust-mss 1412
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname xxxx
ppp chap password 0 xxxxx
ppp pap sent-username xxxx password 0 xxxxx
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer1
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip dns server
ip nat inside source list 101 interface Dialer1 overload
ip nat inside source route-map NAT_RMAP interface Dialer0 overload
access-list 101 permit ip 10.168.0.0 0.0.0.255 any
access-list 101 permit ip 10.168.111.0 0.0.0.255 any
route-map NAT_RMAP permit 10
match ip address 101
control-plane
voice-port 0/0/0
supervisor disconnect dualtone mid-call
input gain 14
compand-type a-law
cptone BE
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 121
impedance complex2
caller-id alerting dsp-pre-allocate
voice-port 0/0/1
supervisor disconnect dualtone mid-call
input gain 14
compand-type a-law
cptone BE
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 121
impedance complex2
caller-id alerting dsp-pre-allocate
voice-port 0/0/2
supervisor disconnect dualtone mid-call
input gain 14
compand-type a-law
cptone BE
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 121
impedance complex2
caller-id alerting dsp-pre-allocate
voice-port 0/0/3
supervisor disconnect dualtone mid-call
input gain 14
compand-type a-law
cptone BE
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 121
impedance complex2
caller-id alerting dsp-pre-allocate
dial-peer cor custom
name local
name longdistance
dial-peer cor list call-local
member local
dial-peer cor list call-longdistance
member longdistance
dial-peer cor list manager
member local
member longdistance
dial-peer cor list other
member local
dial-peer voice 1 pots
corlist outgoing call-longdistance
destination-pattern 0.T
port 0/0/0
dial-peer voice 2 pots
corlist outgoing call-longdistance
destination-pattern 0.T
port 0/0/1
dial-peer voice 3 pots
corlist outgoing call-longdistance
destination-pattern 0.T
port 0/0/2
dial-peer voice 4 pots
corlist outgoing call-longdistance
destination-pattern 0.T
port 0/0/3
dial-peer voice 5 pots
corlist outgoing call-local
destination-pattern 0[2,9].......
port 0/0/0
dial-peer voice 6 pots
corlist outgoing call-local
destination-pattern 0[2,9].......
port 0/0/1
dial-peer voice 7 pots
corlist outgoing call-local
destination-pattern 0[2,9].......
port 0/0/2
dial-peer voice 8 pots
corlist outgoing call-local
destination-pattern 0[2,9].......
port 0/0/3
dial-peer voice 9 pots
corlist outgoing call-local
destination-pattern 0800T
port 0/0/0
prefix 800
dial-peer voice 10 pots
corlist outgoing call-local
destination-pattern 0800T
port 0/0/1
prefix 800
dial-peer voice 11 pots
corlist outgoing call-local
destination-pattern 0800T
port 0/0/2
prefix 800
dial-peer voice 12 pots
corlist outgoing call-local
destination-pattern 0800T
port 0/0/3
prefix 800
telephony-service
no auto-reg-ephone
max-ephones 25
max-dn 25
ip source-address 10.168.10.1 port 2000
auto assign 1 to 20
timeouts interdigit 5
system message Home
max-conferences 8 gain -6
call-forward pattern .T
dn-webedit
transfer-system full-consult dss
transfer-pattern .T
ephone-dn 1 dual-line
number 101
label M.M Office (101)
description M.M Office (101)
name M.M Office
ephone 1
device-security-mode none
video
mac-address 1C17.D3C3.7A31
speed-dial 1 102 label "abc"
speed-dial 2 103 label "def"
speed-dial 3 104 label "hij"
speed-dial 4 113 label "klm"
speed-dial 5 104 label "nop"
speed-dial 6 105 label "qrst"
speed-dial 7 105 label "uvw"
type 7975
button 1:1 2:21
ephone-hunt 1 sequential
pilot 150
list 121
line con 0
exec-timeout 0 0
logging synchronous
login local
line aux 0
line vty 0 4
login local
transport input telnet
scheduler allocate 20000 1000
ntp master 2
ntp update-calendar
end
Router_Home#sh di
Router_Home#sh dia
% Ambiguous command: "sh dia"
Router_Home#sh ds
Router_Home#sh dsv p
Router_Home#sh dspfarm
% Incomplete command.
Router_Home#sh dspfarm ?
all Display all DSPFARM global info
dsp Display DSPFARM DSPs information
profile Display DSPFARM profiles
Router_Home#sh dspfarm ds
Router_Home#sh dspfarm dsp
% Incomplete command.
Router_Home#sh dspfarm dsp all
Total number of DSPFARM DSP channel(s) 0
Router_Home#sh ver
Router_Home#sh version
Cisco IOS Software, 2801 Software (C2801-ADVIPSERVICESK9-M), Version 12.4(15)T10, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 14-Sep-09 14:51 by prod_rel_team
ROM: System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)
Router_Home uptime is 21 hours, 11 minutes
System returned to ROM by power-on
System restarted at 17:31:27 UTC Wed Feb 2 2011
System image file is "flash:c2801-advipservicesk9-mz.124-15.T10.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 2801 (revision 6.0) with 237568K/24576K bytes of memory.
Processor board ID FCZ10491208
2 FastEthernet interfaces
1 ATM interface
2 Virtual Private Network (VPN) Modules
4 Voice FXO interfaces
1 DSP, 8 Voice resources
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
Router_Home#exit
RegardsActually this has been answered already:
https://supportforums.cisco.com/thread/2148571?tstart=0
please do not open duplicate threads. You can delete you post using the Actions panel on the right.
Maybe you are looking for
-
CD Audio and CD Digital controlled by Wave/MP3 sli
Using Platinum Li've! card with digital I/O daughter card. I have connected CD ROM (4 pin) cable to CD In on soundcard and DVD to CD SPDIF in on card (2 pin cable) but both devices are still controlled by the wave/mp3 slider on the surround sound mix
-
Help ! my new ipod touch becomes a brick.
I tried to upgrade iOS of my iPod to latest version 4.3.2, the upgrade process returned unexpected error 1602, I then tried to restore it back to factory setting, but it hang for a few hours. Now it does not want to boot up. What should I do now ?
-
I'm trying to create an applescript to install printers - cant seem to get it to work
So I'm running 10.7and I'm trying to create an applescript to install printers. I'm able to run the first command without issues but the other two keeps giving me error messages in applescript. I assume its because the other two commands have spaces
-
Urgent-------ACLs with Custom Realm.
Can anyone list acls that have to define in my Custom Realm to start default server successfully? Thanks.
-
Im looking to order 2 photo books (separate files)and need to know what the general shipping turnaround is to Adelaide, South Australia. The window specifies the only option is standard shipping and order will be despatched within 3-4 days - is Expre