Cisco Hreap WLC and Apple TV

We are having problems getting apple tv to work for a customer. We have this working on a different controller and the AP (non Hreap). The AP/SSID that is having problems is setup the same (Blocking is set to disabled, and mutlicast is enabled). This one is setup for hreap, is that the problem, is it possible to utilize the airplay with an hreap installation?
Thanks,
Joe

Hi Joe,
What is the wlc model and code running on it?
Is the concerned WLAN enabled for local switching?
- If its in local switching mode, AP multicast mode set to multicast-to-multicast mode will not work, basically not supported. Is that the case?
- If its centrally switched it should work.
- Check if you have other multicast settings set-up correctly, global multicast and IGMP snooping enable.
I assume multicast routing is enabled on all WLc management, AP manager/AP, client vlan.
Regards
Sahil

Similar Messages

Cisco 8510 WLC and RTU licence

Hi Guys,
I have a simular issue where is shows the status as active, not-in-use.
What does this mean and how do I get this to be in use.
This is a Controller with HA-SKU license.
The licenses has been inherited from the Primary Controller.
Any license on HA-SKU controller is disregarded.
Feature name: ap_count (adder)
License type: Permanent
License state: Active, Not-In-Use
License Nodelocked: No
RTU License Count: 50
Hope to hear from you soon.
Regards,
Clifton.

Hi,
since this is a HA-SKU WLC, and the license is inherited from the active then no need to have a permenant license on it.
is the HA working fine?
please review the following link for the HA licensing requirements
http://www.cisco.com/en/US/products/ps10315/products_tech_note09186a0080bd3504.shtml#licensing

Cisco Linksys Routers and Apple Products?

I have to seriously ask if there is simply an incompatibility between Cisco Linksys and Apple products?
I have both the WRT600N and the new E3000. Both are exhibiting the same behavior with my Apple products.
On the wireless connection, I am unable to get a download rate from the Internet, higher then maybe 1.2 - 1.5Mbps. Most of the time it is far lower. I am always using the same site for testing. www.speedtest.net and I always use the same testing server for Dallas, TX.
My ISP is Clear, and when going to www.speedtest.net while using the wired connection on my MacBook Pro, I get a download speed of between 5.5 and 8.2 Mbps.
The upload speed is not changed whether I am using the wired or wireless connection. I also notice the severe difference in speed when I use the Wi-Fi on my iPhone. My 3G connection is faster then the Wi-Fi...
So, is there an advanced config for the wireless that makes it behave better with Apple devices?
I have locked the config so far to 802.11g on the 2.4Ghz transceiver and 802.11n on the 5Ghz receiver. I have also set it not to broadcast the BSSID for either as I live in an apartment complex and I do not want to advertise my network to everyone else. I use WPA personal on the 802.11g network and WPA2 Personal on the 802.11n network.
The settings on the advanced wireless screen in the router config for my E3000 are the defaults.
I have tried nearly everything I can think of. I am now beseeching the help of the community at large in the hopes of gleaning some information that I did not already have. Also I hate the new Cisco Connect app.
On a side note, I was very disappointed to learn that while the WRT600N supported IPv6, the E3000 does not. As a result it seems my wired connection on the MacBook Pro is not performing as well as it did on the WRT600N.
If anyone from Cisco see's this, PLEASE re-add support for IPv6 to your routers. It makes no sense to move backwards now.

Which band you are using to connect the wireless computer...?
Is your other computers are working fine...?
If you are using 5GHz on the router to connect your Mac computer then,make sure the wireless adapter does support 5GHz.
Try the following settings...
Keep the Network Mode as "Mixed".For 2.4GHz...Set the Radio Band to Wide-40MHz and change the Wide channel to 9 and Standard Channel to 11-2.462GHz..For 5GHz...Set the Radio Band to Wide-40MHz and change the Wide channel to159 and Standard Channel to 161-5.805GHz.Click on Advanced Wireless Settings...Change the Beacon Interval to 75,Change the Fragmentation Threshold to 2304,Change the RTS Threshold to 2304 and Click on Save Settings...
Now,power cycle the router and check.

Help required to implement Cisco 2504 WLC and 1042 Access Points

Hi,
My name is Vidya Sagar. I am new to Wireless technology. We are planning to implement Wireless in our office. I have given the requirements below. Kindly go through the details and let me know how to start.
We have purchased Cisco 2504 Wireless Controller (One) and Ciscon 1042 Access Points (Five). At present I am going to use 3 access points only.
I have attached a simple diagram of our office network. We have more than 30 VLANs configured in Core Switch, we are planning to give wifi access to only 3 VLANs.
1. VLAN 121 ( IP Segment - 10.52.121.0 /24)
2. VLAN 116 ( IP Segment - 10.52.116.0 /24)
3. VLAN 100 ( IP Segment - 192.168.100.0 /24) (Guest)
Please give me a implementation plan to do this. I would like to use LDAP or ACS for authentication purpose.
Regards,
Vidya Sagar

Lets just do this simple first before you start using ACS as that will require a certificate installed on the ACS for using PEAP.
So first off, the WLC we will say is in vlan 10. When you are going through the startup wizard, make sure you define the vlan tag to 10 on the management interface. Make sure your virtual interface is an IP address that is not routed in your network, like an out of band IP.
Make sure the WLC time is correct or use NTP!!!!
Now you should be able to http or https to the WLC. I would upgrade the code to v7.4 and install the FUS image. Please reference this link for the upgrade procedure. You don't have to upgrade now... I would wait till you get everything working first.
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn74.html
Now I would connect the APs on the same vlan as the WLC for now. Make sure there is dhcp on that subnet. Once the APs have joined, then you can move them to any subnet you want. Since you don't have many APs it would be okay to leave them in the same vlan as the WLC management or out them on any other vlan you choose. The APs will be connected to an access port NOT a trunk port!!!!
The WLC will need to be connected on a dot1q trunk port only allowing vlans 10,100,116,121. The 2504 running v7.4 will support LAG (etherchannel). Any ways, your switch port should look like this for example only
Interface gigabit1/0/1
description WLC2504
switch port trunk encapsulation dot1q
switchoort mode trunk
switch trunk allowed vlans 10,100,116,121
spanning-tree portfast trunk
channel-mode group 10 mode on << only for v7.4 if you use lag
Don't connect all four ports right now, just port one!!!!
Your Guest vlan, you will need to create an ACL to block traffic from accessing the internal network. You might want to allow dhcp and DNS bit I would leave it open first until you can verify everything is working.
Now on the WLC you need to create a dynamic interface for vlan 100, 116, and 121. If you click on the Controller tab in the GUI and click on interfaces on the left hand side, that will take you to where you can add/delete/modify your interfaces. When creating these interfaces, make sure you add the dhcp server IP address for the primary and or backup.
Now that you have your dynamic interfaces created, its time I create your SSID. Now click on the WLAN tab on the GUI and click on WLAN and then on the too right select Create New and then click go. Select WLAN on the drop down menu and then for the profile name I would use the SSID name also for simplicity.lean e the WLAN id to 1 for this and 2 for the next and so on. After defining these and clicking Apply you can now define your SSID. On the General tab, enable the status and leave the radio policy to all for now, you can decide later what you want to use. Choose your interface you wan to place this SSID on and enable Broadcast SSID for now and leave everything else alone. Now click on the Security tab and on the layer 2 Security, leave it at WPA + WPA2, only check WPA2 Policy and for WPA2 encryption choose AES only. Now go to the bottom of that screen and choose PSk. We will do pre shared key for now so you get to understand the setup and make sure everything is working first. Now on the PSK format, choose ASCII and put your pre shared key in the input box. Make this simple to for testing. You don't want to put in symbols or anything like that. When you are don with that, check apply on the top right and test.
Now you can repeat this with your other SSIDs just to test. Your guest network you can leave open for now to test open authentication.
Here are some links for the WebAuth feature:
https://supportforums.cisco.com/docs/DOC-13954
http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a0080b1a506.shtml
Now if you want to use ACS with PEAP, here is some links for that:
https://supportforums.cisco.com/videos/2499
http://www.cisco.com/en/US/products/ps10315/products_configuration_example09186a0080bd1100.shtml
https://www.google.com/url?sa=t&source=web&cd=8&ved=0CFQQtwIwBw&url=http%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3DWk_bRdmsQlA&ei=_BEyUeCYM8TdqAHHsICAAw&usg=AFQjCNF8PiVBQK1Kipb4j8AzD153bKtmgA&sig2=smHhNVmCr2of2NzbnDhGmw
Well that is it, hopefully you can get the wireless up for testing and verifying everything works!
Sent from Cisco Technical Support iPhone App

Cisco 526 WLC and 2106 WLC in one Mobility Group

Hi,
is it possbile to build a solution with one Cisco 526 Wireless Express Mobility Controller and one Cisco 2106 Wireless LAN Controller in one Mobility Group regarding seamless roaming??
Thank for your answers
Best regards
Stephan

I don't know if it is possible, but I would think if you had any issues, TAC wouldn't support it. Try opening a case with TAC to see.

Prime Infrastructure 2.2- problems: Wired Detailed Device Inventory report not running / Cisco 5500 WLCs no listed in subgroup

New installation of Prime Infrastructure 2.2.0 (PI-VA-2.2.0.0.158.ova)
installed fixes/software/device packs:
PI 2.2.1 Poodle Fix (installed)
PI 2.2.1 Maintenance Release (installed,ncs stopped,rebooted)
Prime Infrastrucutre 2.2 Device Pack 3 (installed,ncs stopped,rebooted)
Licences installed (ncs stopped,rebooted)
Added all devices via Bulk Import (Inventory>Device Management>Network Devices)
Problem 1:
The Cisco 5500 WLCs are not listed in Inventory>Device Management>Network Devices (see screen shot) but listed under "All Devices"!
The Cisco 4400 WLCs and the 8500 WLCs are listed within their subgroup.
Devices are in "Managed State"
Problem 2: fixed! (Browser issue)
Problem 3:
Unable to run "Wired Detailed Device Inventory" report because I get the error message: Failed to run report: Unable to retrieve data for: Chassis Information (if Chassis Information is selected, if System Information is selected I get the error message with ...retrieve data for:System Information)
All devices do have an "Admin Status = Managed" and the Last Inventory Collections Status = Completed.
Has anyone the same issues or a tip for me?
Another topic, the "User Defined Fileds" are not exported when with running a "Device Export" (Inventory > Device Management > Network Devices). ;-(
BR
Bastian

Hallo Bastian,
I think you still have browser issue, Using IE is still the best with Prime.
I have exactly same prime 2.2 and installed fixes/software/device packs.
I have no problem I can see all views. I use now IE 11, with Chrome 42.0.2311.90 and firefox 37.01 I have problems too with lots of views. You have not tell what browser + version you have.
Since you have same prime 2.2 as me. I have other problems, can you check yours?
Can you see a functional CLI template page at Configuration > Templates > Features & Technologies:
https://supportforums.cisco.com/discussion/12481691/can-cisco-prime-22-still-do-simple-ad-hoc-deployment-job-cli-over-all-switches
Do you have SNMP Connectivity Failed while Verify Credentials has no errors all green and checked.
https://supportforums.cisco.com/discussion/12494786/snmp-request-exceeds-internal-data-buffer-512-bytes-prime-22-asa-5545

Cisco 5760 WLC initial config

Hi,
I am configuring up a Cisco 5760 WLC and wondering if it is required to put in a default route? In this document it says to put one in but i dont see why it is needed as it is connected to a switch via a layer 2 Trunk.
Reference:
https://supportforums.cisco.com/docs/DOC-34430
Another question, since there is no more Dynamic Interfaces and they are replaced with Layer 2 & 3 interfaces instead. Do all Layer 2 interfaces you create require a layer 3 interface IP address to be configured also? As shown below:
Thanks

So by default the 5760 has IP routing enabled so you will need to put in a default route. A default gateway won't work unless you disable IP routing first.
Sent from Cisco Technical Support iPhone App

WLC and LWAP Registration Log Question

We have a Cisco 4404 WLC and and about 70 Cisco 1131 APs. I am very new to the Cisco WLC and I need to know how to view its AP registration and unregistration logs. We have a AP that has unregistered and we can't seem to find what switchport it was attached to. It would be helpful to know the IP address and ideally any CDP information it had. Unfortunately you can only view this information in the WLC if the AP is registered, but at this point it is not. Any help would be appreciated.

You will not be able to find that info unless you still see the information on the log about the AP. You would have to either review the switch cdp info as long as the AP is still functioning or else you will just need to physically track it down. If you have WCS or NCS, you should be able to review the past history and the maps would show you where that AP was located if the ap were positioned correctly.
Thanks,
Scott Fella
Sent from my iPhone

Cisco wlc and steel belted radius

we have cisco wlc controller that have two ssid one for user and one for guest
we need the user in ssid 1 take user name and password from user group in active directory through steel belted radiu
please send to me any integrated guide between cisco wlc and steel belted radius
regards

Hi Mohammad,
I am unaware of a specific Steel Belted RADIUS intrgration guide for the WLCs, however the configuration process on the controller will be the same:
Cisco WLC Configuration Guide 7.0 - Configuring RADIUS:
http://www.cisco.com/en/US/docs/wireless/controller/7.0/configuration/guide/c70sol.html#wp1388328
You may wish to contact your RADIUS vendor for additional configuration steps on the server.
Best,
Drew

Cisco WLC and Microsoft NAP

Hi, I want to integrate my Cisco WLC directly into Microsoft NAP. Is this possible?
Thanks

follow the table in the link http://www.cisco.com/en/US/docs/security/nac-nap/1.0/release/notes/NACNAPRN.html#wp1134942 for the integration of WLC and Microsoft NAP

Mobility between Cisco WLC and Meraki(other vendor)

Is it possible that users can roam between Cisco WLC and other vendor wireless gear? Meraki keeps saying it is possible.
They keep saying it is a IEEE feature and everone should support but I do not understand how?

While theoretically possible with the adoption of capwap, it would require all the manufacturers to follow the specs exactly the same. Kind of like hearding cats, not impossible, but highly unlikely.. That's just my opinion
Sent from Cisco Technical Support iPad App

Cisco Valet and Apple TV2 problem.

I just installed a new Cisco Valet router, and though my lap and desktops work fine, I'm unable to get past the "setting time and date" notification when trying to wirelessly connect my Appletv. I tried rebooting the module, but even after waiting considerable time, I simply end up with the screensaver. Any suggestions would be appreciated from this new member
Bob

What is the answer to that problem? I have a cisco router and have the same issue. Thanks

Problem share folder WLC and pc macbookpro

I am doing a migration from my wireless network in the old network in the PC MacBookPro I can see shared files on the network. But when I connect to the SSID configured on the WLC and I can not see shared files on the network. I have no ACL configured on the SSID.

Bonjour is a non-routabe multicast based service. A trick I use sometimes is to configure the WLAN to be in hreap mode if the ap is located locally to the target bonjour device.if your running in local mode, make sure they are on the same vlan and global multicast is enabled.
Sent from Cisco Technical Support iPad App

Cisco 4404 WLC causing a DOS attack several times a day

Hi Everyone
Excuse if this is a duplicate post, but I have searched the forums, but no joy. I also posted it in wireless security as this is where I felt it fits.
Anyway onto my issue:
I manage a CISCO 4404 WLC with about 46 access points across our WAN. System works very well, serving trusted users, guests etc very well.
However, over the last month or two we have had an issue where we have had high load on our WAN.
We have traced this down to the CISCO 4404, about 3-4 times a day, the controller connects to every access point and transmits about 5-8mb of data on port 5427. This in itself would not be a problem, but it connects to all 46 at the same time.
Yes, 46 x 5mb = no WAN for about 2-5 minutes.
ARGH!
So can anyone sugest where I start to look? I am happy to post configs etc. Firmware 7.0.230
Cheers

Hi Steve
Yes it is the capwap port. The remote access points are in hreap mode and servicing trusted network access (802.1x) and guest access is tunnelled across the wan with local breakout from the 4404 via a dedicated vlan. The guest wireless is wpa2.
As the traffic originates from the 4404 and goes to all access points we don't believe it is a network breach. I always hate the phrase "it affects everyone", it usually does not, however in this instance the packeteer shows it does connect to every access point.
DNS is also configured so when new access points are connected they get auto join and get a base configuration.
This issue has been going on since at least Christmas and we put a packeteer box between our wan and our local network. We can say it is the 4404.

Boot camp with Cisco VPN client and smart card

Looking at a Macbook or Macbook Air and the only reason I need to run windows is to be able to access my work network through the Cisco VPN client and my Smartcard then use remote desktop. From my understanding if I run Bootcamp it should work am I correct? Im going to an Apple store tomorrow hopefully they can help too.
Thanks

mrbacklash wrote:
Ok with that being said will the MBA 11.6 1.4ghz have the guts to make it run mostly internet based programs over the VPN connection?
I think if you are running apps over the Internet the bottleneck will be the Internet and your VPN bandwidth. Your computer can certainly execute faster than Internet communications.
Besides, Internet or remote applications run on the remote server. All your local computer does is local processing of the data if necessary.
Message was edited by: BobTheFisherman

Cisco Hreap WLC and Apple TV

Similar Messages

Maybe you are looking for