Cisco IOS XE for 5508 and 2504 WLCs

Hi,
does anybody know whether new IOS XE introduced for WLC 5760 will be also available for 5508 and 2504 series controllers?
Thank you.
Regards
Karel Navratil

No it will not be.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Similar Messages

Configuring Guest Access using 2 LWAPs and 2504 WLC

Please advise,
I have 2 APs, Cisco Aironet 1040, and 2504 WLC.
Is it possible to configure guest access (Guest SSID/VLAN and Corporative SSID/VLAN) without dedicated guest WLC in DMZ?

Yes you can. You can have up to 16 SSIDs per AP, but not suggested to have all 16. You can either use one port on the 2504 for both SSID/vlan or specify which port is for corporate and which one is for guest.
Thanks,
Scott Fella
Sent from my iPhone

Flex 4.5:Convert mxml project into IOS project for ipad and iphone

Hi All,
I created a mxml project and now i want to convert the same project in Flex builder 4.5 IOS project for iphone and ipad but its seems the mobile project doesnot support mxml.
I am using module and moduleloader and in Flex 4.5, they said the use of this is discourage. I didi not get any alternative of them.
Please help me to convert this application in IOS.
Thanks,
Saurabh Shrotriya

Modules are not supported on iOS due to Apple's App Store terms of service.

HT201210 Keep getting error 9006 when updating iOS system for iPOD and iPHONE and not sure what to do, any solutions

Keep getting error 9006 when updating iOS system for iPOD and iPHONE and not sure what to do, any solutions?

Errors related to third-party security software
Error 2, 4 (or -4), 6, 1000, and 9006
Follow the steps to troubleshoot security software. Often, uninstalling third-party security software will resolve these errors.
There may be third-party software that modifies your default packet size in Windows by inserting a TcpWindowSize entry into your registry. An incorrectly set default packet size can cause these errors. Contact the manufacturer of the software that installed the packet size modification for assistance or follow this article by Microsoft: How to reset Internet Protocol (TCP/IP).
Verify that access to ports 80 and 443 are allowed on your network.
Verify that communication to albert.apple.com or phobos.apple.com isn't blocked by a firewall or other Internet security setting.
Discard the .ipsw file, open iTunes and attempt to download the update again. See the steps under "Advanced steps > Rename, move, or delete the iOS software file (.ipsw)" below for file locations.
Restore your device while connected to a different network.
Restore using a different computer.
Errors related to downgrading iOS

881 IOS support for IPSEC and OSPF

Is there an IOS image for the 881 that contains IPSEC feature set AND support for OSPF? I recently purchased an 881 and it came default with this system image "c880data-universalk9-mz.152-4.M4.bin", however this image does not support OSPF. I need an IOS image that supports both OSPF and IPSEC feature sets. Please advise.

hi,
according to cisco's FN, you might need a c880data-universalk9-mz.153-2.T1.bin.

HT4623 itunes keep saying theres network setting or connectivity issues after downloading ios 7 for hours and never completes the download. What do I do?

Hi,
I really hope someone can help me. Ive been trying to download the newest ios 7 for 2 days. It always starts very slow and says it will take up to 5 hours. IT ususally downloads for about 2 hours before showing an error and claiming |II have newtwork setting issues or connectivity problems but my internet connection is fine. This is soooo frustrating I cant keep wasting all this time for nothing!!!! Eveytime the error shows up I have to rstart downloading from the beginning! Please HELP ME

1.Turn off your device. If you can't turn it off, press and hold the Sleep/Wake and Home buttons at the same time and wait a few seconds for it to turn off.
2.Plug the device's USB cable into your computer only.
3.Hold down the device's Home button as you connect the USB cable to it.
4.When you see the Connect to iTunes screen, release the Home button. If you don't see this screen, try steps 1 through 3 one more time.
5.Use iTunes to restore your device.
Additional Information:
If you started your device in recovery mode by mistake, restart it to exit recovery mode. Or you can just wait—after 15 minutes the device will exit recovery mode by itself. If you want a faster way to solve iPad Stuck in Recovery Mode, try iPad data recovery software.

Cisco IOS Zone Based Firewall and IPv6

Hello,
I am trying to setup IPv6 tunnel to tunnel-broker Hurrican Electrics. IPv6 connection is working OK only if I disable zone security on WAN interface (Fe0 - IPv4 interface).
Which protocols must be alloved to and from router?
IOS version: 15.1.2T1 (Adv.ip services)
Setup:
HE (tunnel-broker) --- Internet (IPv4) ---- Cisco 1812 (Fe0 (IPv4) and interface tunnel 1 (IPv6))
Config on router:
IPv4 (self to internet and internet to self)
policy-map type inspect Outside2Router-pmap
class type inspect SSHaccess-cmap
inspect
class type inspect ICMP-cmap
inspect
class type inspect IPSEC-cmap
pass
class type inspect Protocol41-cmap
pass log
class class-default
drop
interface Tunnel1
description Hurricane Electric IPv6 Tunnel Broker
no ip address
zone-member security IPv6tunnel
ipv6 address 2001:47:25:105B::2/64
ipv6 enable
ipv6 mtu 1300
tunnel source FastEthernet0
tunnel mode ipv6ip
tunnel destination xxx.66.80.98
interface FastEthernet0
description WAN interface
ip address xxx.xxx.252.84 255.255.0.0
no ip redirects
no ip unreachables
no ip proxy-arp
zone-member security WAN
duplex auto
speed auto
zone-pair security IPv6Tunnel_2_WAN source IPv6tunnel destination WAN
service-policy type inspect IPv6-out-pmap
zone-pair security WAN_2_IPv6tunnel source WAN destination IPv6tunnel
service-policy type inspect IPv6-out-pmap
policy-map type inspect IPv6-out-pmap
class type inspect IPv6-internet-class
inspect
class class-default
drop
class-map type inspect match-all IPv6-internet-class
match protocol tcp
match protocol udp
match protocol icmp
match protocol ftp
ipv6 route ::/0 Tunnel1
ipv6 unicast-routing
ipv6 cef
parameter-map type inspect v6-param-map
ipv6 routing-header-enforcement loose
sessions maximum 10000

OK, removed the cmap the packet was getting dropped on, so the current self to wan zone-pair policy map looks like this:
policy-map type inspect pm-selftowan
class type inspect cm-selftowan-he-out
inspect
class type inspect cm-dhcpwan
pass
class class-default
drop
class-map type inspect match-all cm-selftowan-he-out
match access-group name HETunnelOutbound
ip access-list extended HETunnelOutbound
permit 41 any any
permit ip any host 64.62.200.2
permit ip any host 66.220.2.74
permit ip any host 216.66.80.26
Now we see the same error, just on the 'new' first cmap in the pmap:
*Oct 5 02:39:31.316 GMT: %FW-6-DROP_PKT: Dropping Unknown-l4 session :0 216.66.80.26:0 on zone-pair selftowan class cm-selftowan-he-out due to Invalid Segment with ip ident 0
Yet as you can see above, we are allowing proto 41 any any.
I didn't expect any other result really since the previous cmap had 'permit ip any any' but still
any ideas?
Thanks,
//TrX
EDIT: Out of curiosity after reading this post: https://supportforums.cisco.com/thread/2043222?decorator=print&displayFullThread=true
I decided to change the outbound cm-selftowan-he-out action to 'pass'.
I suddently noticed the following log:
*Oct 5 02:39:31.316 GMT: %FW-6-DROP_PKT: Dropping Unknown-l4 session 216.66.80.26:0 :0 on zone-pair wantoself class cm-wantoself-he-in due to Invalid Segment with ip ident 0
Notice this is now inbound having trouble where as before was outbound.
I changed the inbound pmap policy for cmap cm-wantoself-he-in to pass also and IPv6 PACKETS ARE GETTING ICMP6 REPLIES FROM GOOGLE!
Looking at the original outbound PMAP:
policy-map type inspect pm-selftowan
class type inspect cm-selftowan
inspect
class type inspect cm-selftowan-he-out
inspect
class type inspect cm-dhcpwan
pass
class class-default
drop
cm-selftowan has always been infront of cm-selftowan-he-out, and because that is ip any any, it has been 'grabbing' the IP proto 41 packets and doing ip inspect on them (which fails as it seems ip inspect only handles a handful of proto's).
This is why setting cm-selftowan-he-out and cm-wantoself-he-in both to 'pass' instead of 'inspect' in the past has not been doing anything, because the outbound packets were never getting to the cm-selftowan-he-out cmap.
Would never have got to this without ip inspect log. Why didn't I think of just trying ip inspect logging two days ago!
Anyway, thank you, I have now restored my faith in my own knowledge of ZBF!
Hope this helps the OP too
//TrX

Cisco IOS supporting both voice and vpn

Hi Friends
i have one 2821 router.Can any one suggesting which ios will support both voice and vpn?

Questions like this are better/faster answered by checking feature navigator.
http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp
My suggestion is to run an MD release.
Also a big dated document:
http://www.cisco.com/en/US/products/sw/iosswrel/ps1834/products_tech_note09186a00800fb9d9.shtml
For old software and hardware you can also check out Figure 1 here:
http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps708/product_bulletin_c25_506007.html
M.

Cisco WAAS MIB for CPU AND MEMORY

Hi,
I am looking to query Cisco WAAS WAVE and SRE device for basic stuff cpu, memory, interface.
I managed to get the CPU stats via SNMP using HOST-RESOURCES-MIB, however i cannot use the memory usage utilisation.
Can you please help.
Furthermore, I wanted to have some environmental values, temperature. Is there any MIB for that purpose.
Thanks

There's a "Show cpu " commmand availabe. Type help or '?' for a list of available commands.

Configuring Cisco Aironet 1140 for Radius and setting up a Radius server

guys i need some help setting up my Radius to work with cisco aironet 1140, i am new at this however i was tasked with setting up a Radius server and setting our AP with WPA2- enterprise so users can log into our AP using AD credentials.
When i try to setup on the AP a new SSID i do not see the option for WPA2- enterprise?

Here are other links with examples:
https://supportforums.cisco.com/thread/331581
http://targetcisco.blogspot.com/2011/03/cisco-autonomous-access-point.html
http://downloads.avaya.com/css/P8/documents/100041614
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Just updated to iOS 6 for iPhone, and now Yahoo takes forever to load.

Help! I updated my iPhone 4 to iOS 6 and now my Yahoo mail either takes forever to load, or never loads at all. Both receiving and sending are sketchy and go at a snail's pace.
I've scoured the Internet and tried all the fixes - deleted account and added again (multiple times), restarted phone, added yahoo account as "other", logged in from a computer, turned off iCloud...
It's driving me bonkers... What am I missing? Yahoo mail still works fine on my iPad, which is running the older iOS.
Heeeeeelp!

iOS: Not responding or does not turn on
Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is the thing to do

Bug? Cisco Jabber Video for TelePresence and spanish keyboard

Hello everybody,
because of a customer request I checked Jabber Video with spanish keyboard configured (traditional sort) an figured out, that with this configuration the Jabber Client (tested with 4.2, 4.6 and 4.8.8) doesn't accept the pound key when it is pressed on the keyboard. In Word for example the pound key works as expected. At the moment I told the customer to use the "onboard" keyboard in the Jabber Video client, but I think it is a bug (don't know if it's a bug in Jabber Video or Windows 7). Has anyone experienced the same? Maybe this will be fixed in future?
Regards, Daniel

You can have both "free" and "enterprise" versions installed on a Mac.
If you already have "enterprise" version installed on a PC, and you install the "free" version, the registry settings will be changed and server setting locked to
https://sjc1-movi-pr-bootproxy-vip.ciscojabbervideo.com/endpoint/configuration
when you install the "free" version, so ,no, you can't have both versions installed on the same PC.
You can change the registry settings so it's not locked to the Cisco server, but then you might as well just have the "enterprise" version installed and just edit the internal server settings to use the above URL if you want to make it behave as the "free" version.
There's no difference, clientwise, between the two, the server settings determines which server it will register with, and provisioning settings will change accordingly.
/jens

Cisco MDS Vsan for EVA8100 and EMC Clariion (Same or Seperate)

We have EMC Clariion Frame CX600,CX700 and Cisco MDS Fabric with 2 VSANS currently.
We have just procured EVA8100 and wanted to find out, do we create 2 additional VSANS to support it or add EVA8100 in the existing VSANS.
IVR is not enabled on Cisco MDS.
Also we'll be phasing out the EMC frames and want to migrate data from Clariion LUNS , so debating to put EVA8100 in same VSANS, so data can be migrated over same VSANS.
Also heard that earlier if EMC Clariion was brought online before EVA frame then CommandView would not find EVA, so EVA needs to be booted first (May have been fixed).
Thanks

G'day,
You do not need to create new vsan's when adding new devices to a fabric. You will however need to change the zoning configuration to allow hosts to see the newly attached storage array.
VSAN's are a way of segregating traffic within a single physical fabric. One good method of using them is to segregate development from production traffic.
For further info on VSAN's see "http://www.cisco.com/en/US/netsol/ns340/ns394/ns259/ns261/networking_solutions_white_paper09186a0080114c21.shtml"
Cheers

Cisco ISE protocols for ldap and Windows wireless client

Only the protocols below are supported by ise in combination with ldap identity sources.
EAP-GTC, PAP, EAP-TLS, PEAP-TLS.
Mac OS devices seem to be able to use these but Windows users seem to be having problems. How should windows users connect with ise that only uses ldap?

Mathieu,
Take a look at the user guide for NAM -
http://www.cisco.com/en/US/docs/security/vpn_client/anyconnect/anyconnect30/administration/guide/ac04namconfig.html
You will see the protocols support like GTC that should allow you not to have to deploy certs.
Thanks.
Tarik Admani
*Please rate helpful posts*

Cisco IOS IPS in Cisco 2921/k9 router

Hi All,
I have a router of Cisco 2921 series (C2921/K9) basic box with IP BAse IOS image (SL-29-IPB-K9 IOS). I would like to enable IOS Level IPS feature on this Router now. Based on the Cisco Document i have found i need to purchase an additonal subscripton license to enale the IPS feature. My querry is-
Will it support on the Basic IP Base IOS or do i need to change the IOS?
If i need to purchase the Subscription Licesne, how can i get the part number and cost for the same?
Do i need to buy any addtional module for this like (NME-IPS-K9) ?
Thanks in advance for your quick support
regards
Sunny

Hi Sunny
1. Yes you can enable IPS on IOS with the security license, without buying a subscription, but this would make little sense - new signatures are being released all the time so you would not be protected from recently discovered vulnerabilities/attacks.
2. Correct, the modules and appliances run a different kind of software and are much more powerful
3. If you add the module, you do NOT need the security license. It would still be advised to get a subscription license to get signature updates for the module.
I hope this helps, let us know.
regards
Herbert
jacob.samuel wrote:Dear Herbert,Thanks alot for the wonderful post. It clear most of my doubts. Still i kindly need to know few more points-1) Cant we enable IPS Feature on 2921/K9 router (with Sec license or 2921Sec/K9 bundle) without signature subscription license (is it a must? it is for getting updates of signatures and for support only, right?)2) I came to know from a distributor pre-sales engineer that the Cisco IOS Level Intrusion Protection is not going to provide the full feature of IPS like NME module or IPS Applinace. Is that right?3) If i add NME-IPS-K9 Module to my 2921 Router, without enabling Sec License, can i enable IPS feature on the Router. Or is it a must that i need to buy Sec License (SL-29-SEC-K9)?Attaching the Datasheet of NME-IPS-K9 module (Page num 5 above Table 3) mentione as follows-Cisco IOS Software Feature Sets and ReleaseTable 3 lists the required Cisco IOS feature sets and releases for Cisco IPS AIM and IPS NME on the Cisco 1841,
2800 and 3800 series Integrated Services Routers Note that, IPS NME on the Cisco 2900 and 3900 Integrated
Services Routers does not require a Security Feature license.
In that case if i buy a module i can install it on the 2921K9 box directly and can enable the IPS feature right? I dont need any License and additonal signature subscription here to enable the IPS feature (if i dont need signature updates and support) right?
thanks alot for the support.
regards
Sunny

Cisco IOS XE for 5508 and 2504 WLCs

Similar Messages

Maybe you are looking for