Cisco IP Phone 7945-G or 7965-G screen goes blank randomly with SCCP firmware 9.2(3) on CUCM 8.6(2a)
Hello everybody,
I have the following situation:
A WAN VoIP network, with centralized call processing model (central site and few branches)
Cisco IP Phones 7945-G and 7965-G running SCCP
Cisco Unified Communications Manager 8.6(2a)
SCCP firmware Release 9.2(3) for the above mentioned hardware models
The problem that occurs randomly is that either when the firmware was SCCP firmware Release 9.2(1), or it was upgraded to SCCP firmware Release 9.2(3), approximately 5 Cisco IP Phones, the screen goes blank, the phone being still operational (but difficult to operate in such circumstances), and the problem persists until it is disconnected from PoE, and re-connected.
Please if possible, any solution to this problem is much appreciated.
Thank you in advance.
Radu
Hello again,
In addition to what I already mentioned, I would like to detail a few aspects, in order to be more specific with this behavior:
- From the total number of Cisco IP phones which is less than 1000, this behavior happened randomly, within 1 month and 3 weeks
- Actually, it was a total number of 8 Cisco IP phones whose display went off, 4 being located in Headquarters, and from the other 4, 3 were in the same Branch, and 1 in another Branch
- Also, 7 IP phones are connected in non-Cisco switches with PoE, and 1 IP Phone was power supplied from AC adapter
- initially, all existing IP phones had firmware Release 9.2(1) for 7945G and 7965G, and the mentioned behavior happened with 4 IP phones
- then, for all IP phones, it were upgraded to firmware Release 9.2(3) for 7945G and 7965G, but problem re-appeared with other 4 IP phones
The only solution that solved the issue for each IP phone was to disconnect the power from the IP phones.
I hope that you might help me on how to get solving this problem, and I am looking forward for any useful idea or solution.
Many thanks in advance.
Regards,
Radu
Similar Messages
-
When I am on a phone call and I double click the button to go to my home screen, then open another application (usually my calendar program, Calengoo), my screen goes blank and I am not able to return to either the app, the phone, or the home screen. If I am speaking to a person, if they hang up then I am back to the phone application. If I'm leaving a message, I am unable to return to the phone screen to end the call, and have to wait until the other phone hangs up. I'm also unable to switch back and forth to look at my calendar if I'm calling someone about scheduling. This has only started happening since the most recent iOs update. I run into situations similar to this about once per day during the work week, as I use my phone is this manner quite often. While not life altering it is quite frustrating. Can anyone here help me figure out a way to avoid this? If it helps, I have noticed a general downgrade in overall performance starting two system updates ago (apps opening more slowly, closing unexpectedly more often, etc.). I have an iPhone 3GS with the latest OS update.
Thank you for any help or suggestions,
ChrisI could be corrupted backup.
You can check the notification settings for message.
Settings>Notification Center>Messages>Alert Style
It should be on Banners or Alerts.
Settings>Messages> Turn on Imessage and send as SMS and below that "Blocked" to check if you have any numbers block might be blocking the message.
You can also do a hard reset by holding power and home till it restarts and release after seeing the apple logo.
Still doesn't work? Settings>General>Reset>Reset all settings -
My phone screen goes blank and after a minute or so goes back to home screen. why?
hello. my phone screen goes blank and after a minute or so goes back to home screen. why? any help please?
Howdy mbaeguasu,
It sounds like your iPhone may be restarting unexpectedly while you’re using it. Take a look at the article linked below and, if you haven't already, try installing the latest version of iOS on your device.
If your iOS device restarts, displays the Apple logo, or powers off while you're using it - Apple Support
So long,
-Jason -
whenevenr I call a person sometimes the phone gives me an option of callback and end when I press the callback button the whole screen goes blank and only the upper Taskbar where it shows network provider , time and battery percentage is shown
Standard troubleshooting...
Try a reset by pressing the home and sleep buttons until you see the Apple logo, ignoring the slider if, it comes up. Takes about 5-15 secs of button holding and you won't lose any data or settings.
Remove all apps from Recently Used list...
- From any Home Screen, double tap the home button to bring up the Recents List
- Tap and hold any icon in this list until they wiggle
- Press the red (-) to delete all apps from this list.
- Press the home button twice when done.
If still a problem restore with your backup.
If still a problem restore as new, i.e. without your backup. See how it runs with nothing synced to it.
If still a problem, it's likely a hardware issue. -
It seems that after 911 fix(update) my phone screen goes blank after dialing and to enter voice mail I code have to keep pressing unlock button for screen to return for split second for each code digit. Has anyone else seen this behavior?
Thanks,
enrI noticed exactly the same thing. It's a struggle to retrieve my voicemail because the screen goes blank and by the time I finally get to finish entering my voicemail password, the Verizon system times out and says goodbye.
COME ON VERIZON, MY PHONE IS NOT USEABLE LIKE THIS !!!
One thing gets fixed, 3 things get broken. Enough already.
Instead of giving us half-a*s "band-aid" updates, let's get us updated to FROYO and fix the darn phone the right way. -
I have a Sony Ericsson Zylo. When I slide open the phone the screen goes blank. Can anyone help?
I have a Sony Ericsson Zylo and when I slide open the phone the screen goes blank.
http://talk.sonyericsson.com/message/10220#10220 Link to similar thread.
-
I cannot access my device. The screen is blank however it has power. The phone will ring but since the screen is blank I cannot answer. It seems to be dead but has power?
When restoring to factory defaults/new iPod fails to resolve a problem that indicates a hardware problem an an appointent at the Genus Bar of an Apple store is in order.
Check your warranty coverage here:
Apple - Support - Check Your Service and Support Coverage -
http://www.youtube.com/watch?v=rY_WU8WadXE
Did you perform a battery pull afterwards?
With the phone POWERED ON, remove the battery for 15-30 seconds, then reinsert and wait for the phone to completely reboot.
"Cats may taste like chicken, but they have more bones than rabbits."
Blackberry 101
Tips & Tricks
Videos to learn from on youtube -
Screen goes blank while using phone
If this happens with your 3G, I bet it's because it's in a case you purchased for the old model. Take it out of the case and see if it works.
Do you use a case or sleeve on your iPhone? If the case blocks the proximity sensor(s), the phone may still think you are holding it next to your face and black out the display so you don't disconnect or do something else unintended "by cheek."
I had this problem too and fixed it by modifying the el cheapo holster case with a razor blade - works fine now. Depending on which iPhone model you have, there will be one or two proximity sensors to the left or right of the earpiece speaker at the top of the phone. Make sure this area is clear, and you should be fine. This also fixes any problems people are having with random screen bright/dark changes since the light sensor is located in the same area. -
Cisco IP Phone 7962 not registering with CME 9
Dear Experts,
I have CME router 2811 with 15 - 6921 phones and added 1 new Cisco 7962 phone. All the 6921 phones are registered and working fine.
7962 phone does not register and the screen goes blank after the phone boot. Software version the phone is running is 9.3.1 SR2-1S
Verified the CNF File is created
tftp-server system:/its/vrf1/XMLDefault7962.cnf.xml alias SEP501CBFFC8735.cnf.xml
Here is the configuration on the router.
ip dhcp pool VOICE
network 192.168.10.0 255.255.255.0
default-router 192.168.10.1
option 150 ip 192.168.10.1
ephone-dn 11 octo-line
number 2211
label ABC 2221
name ABC
ephone 11
device-security-mode none
mac-address 501C.BFFC.8735
type 7962
button 1:11
The results of the debug tftp events are as below -
Oct 26 17:52:06.491: TFTP: Looking for CTLSEP501CBFFC8735.tlv
Oct 26 17:52:06.595: TFTP: Looking for ITLSEP501CBFFC8735.tlv
Oct 26 17:52:06.699: TFTP: Looking for ITLFile.tlv
Oct 26 17:52:06.931: TFTP: Looking for SEP501CBFFC8735.cnf.xml
Oct 26 17:52:07.487: TFTP: Opened system:/its/vrf1/XMLDefault7962.cnf.xml, fd 10, size 1278 for process 366
Oct 26 17:52:07.495: TFTP: Finished system:/its/vrf1/XMLDefault7962.cnf.xml, time 00:00:00 for process 366
Oct 26 17:52:09.799: TFTP: Looking for English_United_States/mk-sccp.jar
Oct 26 17:52:10.119: TFTP: Looking for United_States/g3-tones.xml
Oct 26 17:52:11.067: New Skinny socket accepted [2] from 0, sub 1 (15 active)
Oct 26 17:52:11.067: sin_family 2, sin_port 49152, in_addr 192.168.110.30
Oct 26 17:52:11.067: skinny_add_socket 2 192.168.110.30 49152
Oct 26 17:52:11.799: Cannot find device entry on socket fd 7 for message 346
Oct 26 17:52:11.799: Got wrong skinny message size 1836597052 on socket fd 7
Oct 26 17:52:11.799: Got wrong skinny message size 824327534 on socket fd 7
Oct 26 17:52:11.799: Got wrong skinny message size 1735289188 on socket fd 7
Oct 26 17:52:11.799: Got wrong skinny message size 1007304255 on socket fd 7
Oct 26 17:52:11.799: Got wrong skinny message size 1918987361 on socket fd 7
Oct 26 17:52:11.799: Got wrong skinny message size 1632510061 on socket fd 7
Oct 26 17:52:11.799: Got wrong skinny message size 1333032271 on socket fd 7 ... .so on
Oct 26 17:52:11.815: Got wrong skinny message size 2622 on socket fd 7
Oct 26 17:52:11.815: Got wrong skinny message size 0 on socket fd 7
Oct 26 17:52:11.815: Got wrong skinny message size 0 on socket fd 7
Oct 26 17:52:11.815: Got wrong skinny message size 0 on socket fd 7
Oct 26 17:52:11.815: Got wrong skinny message size 0 on socket fd 7
Oct 26 17:52:11.815: Got wrong skinny message size 0 on socket fd 7
Oct 26 17:52:11.815: Got wrong skinny message size 0 on socket fd 7
Oct 26 17:52:11.815: Got wrong skinny message size 0 on socket fd 7
Oct 26 17:52:11.815: Got wrong skinny message size 0 on socket fd 7
Oct 26 17:52:11.815: Got wrong skinny message size 0 on socket fd 7
Oct 26 17:52:11.815: Got wrong skinny message size 0 on socket fd 7
Oct 26 17:52:11.815: Got wrong skinny message size 0 on socket fd 7
Oct 26 17:52:11.815: Got wrong skinny message size 0 on socket fd 7
Oct 26 17:52:11.815: Got wrong skinny message size 0 on socket fd 7
Oct 26 17:52:11.815: Got wrong skinny message size 0 on socket fd 7
Oct 26 17:52:11.815: Got wrong skinny message size 0 on socket fd 7.. so on
Oct 26 17:52:11.883: Cannot find device entry on socket fd 7 for message 0
Oct 26 17:52:11.883: Got wrong skinny message size -2056126442 on socket fd 7
Oct 26 17:52:11.883: Got wrong skinny message size -54584240 on socket fd 7
Oct 26 17:52:11.883: Got wrong skinny message size 3 on socket fd 7
Oct 26 17:52:11.883: Got wrong skinny message size 0 on socket fd 7
Oct 26 17:52:11.883: Got wrong skinny message size 0 on socket fd 7
Oct 26 17:52:11.883: Got wrong skinny message size 825045805 on socket fd 7
Oct 26 17:52:11.883: Got wrong skinny message size 0 on socket fd 7
Oct 26 17:52:21.915: Cannot find device entry on socket fd 7 for message 0
Oct 26 17:52:41.995: Cannot find device entry on socket fd 7 for message 0
Oct 26 17:53:02.064: Cannot find device entry on socket fd 7 for message 0
ADVILLA-2811#
Oct 26 17:54:24.556: socket 3 fatal error 260! can't read msg header with size -1, fd 3
Oct 26 17:54:24.556: it's a stale socket! delete it!!
Please advise the issue.. thanks..This could be a compatibility issue. Looking at the feature matrix, 15.1 is CME8.8 and only has support for SCCP42.9-2-1S.loads. Even the latest CME (10.5) only has listed support for 9.2.1 on 7962.
I would try downgrading the phone firmware to 9.2.1 and see if you continue to have the issue.
Also, make sure you are advertising all the following files on TFTP:
SCCP42.9-2-1S.loads
apps42.9-2-1TH1-13.sbn
cnu42.9-2-1TH1-13.sbn
cvm42sccp.9-2-1TH1-13.sbn
dsp42.9-2-1TH1-13.sbn
jar42sccp.9-2-1TH1-13.sbn
term42.default.loads
term62.default.loads -
When I use the I-Phone, on a call, then I take the phone away from my ear, the screen goes black. The call doesn't end, just the screen goes black.
Does this happen on calls that you initiate or calls that come in while the phone is asleep? If its only on calls that come in while the phone is asleep, that would be normal behavior. After a call comes in, the iPhone returns to the state it was in before the call. Also, as Tamara suggested, if you are using a case for the iPhone, make sure it isn't covering any of the proximity sensors under the top of the glass.
-
Phone blinks, has stripes that obscure screen.
Phone blinks, has stripes that obscure screen, tried hard reset with out change. Have Googled for solutions and found many people with same problem but no fixes.
The talking "phone" functions have worked OK since I bought the phone. But now can often not see the screen adequately. However the app functions that involve heavier web use, face book, note taking, etc often never complete.Hi Gezenplat,
You need a phone that works without screen issues! Since you have already done a hard reset http://vz.to/YA8BX6 and it did not resolve the issue, you most likely need a replacement device. Is your phone within the 1 year manufacturer's warranty? If so, you may qualify for a free warranty replacement http://vz.to/uyYF0o as long as no physical/water damage exist. Do you have insurance? If so, you can process claim PhoneClaim.com/Verizon online and get an insurance replacement pronto!
Antonio_VZW
Please follow us on twitter @VZWSupport -
I have cisco phone 7945 and I have upgraded it to SIP but the phone keep registering and never seem to register with my asterisk PBX.
Kindly view my SEP(mac).cnf.xml file for any error.
<?xml version="1.0" encoding="UTF-8"?>
<!-- created with XMLSpear -->
<device>
<deviceProtocol>SIP</deviceProtocol>
<sshUserId>admin</sshUserId>
<sshPassword>password</sshPassword>
<devicePool>
<dateTimeSetting>
<dateTemplate>D/M/Y</dateTemplate>
<timeZone>Central Standard/Daylight Time</timeZone>
<ntps>
<ntp>
<name>172.100.101.229</name>
<ntpMode>Unicast</ntpMode>
</ntp>
</ntps>
</dateTimeSetting>
<callManagerGroup>
<members>
<member priority="0">
<callManager>
<ports>
<ethernetPhonePort>2000</ethernetPhonePort>
<sipPort>5060</sipPort>
<securedSipPort>5062</securedSipPort>
</ports>
<processNodeName>172.100.101.229</processNodeName>
</callManager>
</member>
</members>
</callManagerGroup>
</devicePool>
<sipProfile>
<sipProxies>
<backupProxy>172.100.101.229</backupProxy>
<backupProxyPort>5060</backupProxyPort>
<emergencyProxy></emergencyProxy>
<emergencyProxyPort></emergencyProxyPort>
<outboundProxy></outboundProxy>
<outboundProxyPort></outboundProxyPort>
<registerWithProxy>true</registerWithProxy>
</sipProxies>
<sipCallFeatures>
<cnfJoinEnabled>true</cnfJoinEnabled>
<callForwardURI>x-serviceuri-cfwdall</callForwardURI>
<callPickupURI>x-cisco-serviceuri-pickup</callPickupURI>
<callPickupListURI>x-cisco-serviceuri-opickup</callPickupListURI>
<callPickupGroupURI>x-cisco-serviceuri-gpickup</callPickupGroupURI>
<meetMeServiceURI>x-cisco-serviceuri-meetme</meetMeServiceURI>
<abbreviatedDialURI>x-cisco-serviceuri-abbrdial</abbreviatedDialURI>
<rfc2543Hold>true</rfc2543Hold>
<callHoldRingback>2</callHoldRingback>
<localCfwdEnable>true</localCfwdEnable>
<semiAttendedTransfer>true</semiAttendedTransfer>
<anonymousCallBlock>2</anonymousCallBlock>
<callerIdBlocking>2</callerIdBlocking>
<dndControl>0</dndControl>
<remoteCcEnable>true</remoteCcEnable>
</sipCallFeatures>
<sipStack>
<sipInviteRetx>6</sipInviteRetx>
<sipRetx>10</sipRetx>
<timerInviteExpires>180</timerInviteExpires>
<timerRegisterExpires>240</timerRegisterExpires>
<timerRegisterDelta>5</timerRegisterDelta>
<timerKeepAliveExpires>120</timerKeepAliveExpires>
<timerSubscribeExpires>120</timerSubscribeExpires>
<timerSubscribeDelta>5</timerSubscribeDelta>
<timerT1>500</timerT1>
<timerT2>4000</timerT2>
<maxRedirects>70</maxRedirects>
<remotePartyID>false</remotePartyID>
<userInfo>None</userInfo>
</sipStack>
<autoAnswerTimer>1</autoAnswerTimer>
<autoAnswerAltBehavior>false</autoAnswerAltBehavior>
<autoAnswerOverride>true</autoAnswerOverride>
<transferOnhookEnabled>false</transferOnhookEnabled>
<enableVad>false</enableVad>
<preferredCodec>g729</preferredCodec>
<dtmfAvtPayload>101</dtmfAvtPayload>
<dtmfDbLevel>3</dtmfDbLevel>
<dtmfOutofBand>avt</dtmfOutofBand>
<alwaysUsePrimeLine>false</alwaysUsePrimeLine>
<alwaysUsePrimeLineVoiceMail>false</alwaysUsePrimeLineVoiceMail>
<kpml>3</kpml>
<phoneLabel>LIGHTNING</phoneLabel>
<stutterMsgWaiting>1</stutterMsgWaiting>
<callStats>false</callStats>
<silentPeriodBetweenCallWaitingBursts>10</silentPeriodBetweenCallWaitingBursts>
<disableLocalSpeedDialConfig>false</disableLocalSpeedDialConfig>
<sipLines>
<line button="1">
<featureID>9</featureID>
<featureLabel>101</featureLabel>
<proxy>172.100.101.229</proxy>
<port>5060</port>
<name>101</name>
<displayName>101</displayName>
<autoAnswer>
<autoAnswerEnabled>10</autoAnswerEnabled>
</autoAnswer>
<callWaiting>3</callWaiting>
<authName>101</authName>
<authPassword>line secret</authPassword>
<sharedLine>false</sharedLine>
<messageWaitingLampPolicy>1</messageWaitingLampPolicy>
<messagesNumber>*99</messagesNumber>
<ringSettingIdle>4</ringSettingIdle>
<ringSettingActive>5</ringSettingActive>
<contact>101</contact>
<forwardCallInfoDisplay>
<callerName>true</callerName>
<callerNumber>false</callerNumber>
<redirectedNumber>false</redirectedNumber>
<dialedNumber>true</dialedNumber>
</forwardCallInfoDisplay>
</line>
<line button="2">
<featureID>20</featureID>
<featureLabel>Menu</featureLabel>
<serviceURI>http://example.domain.ext/services/menu.xml</serviceURI>
</line>
</sipLines>
<voipControlPort>5060</voipControlPort>
<startMediaPort>16348</startMediaPort>
<stopMediaPort>20134</stopMediaPort>
<dscpForAudio>184</dscpForAudio>
<ringSettingBusyStationPolicy>0</ringSettingBusyStationPolicy>
<dialTemplate>dialplan.xml</dialTemplate>
<softKeyFile></softKeyFile>
</sipProfile>
<commonProfile>
<phonePassword></phonePassword>
<backgroundImageAccess>true</backgroundImageAccess>
<callLogBlfEnabled>2</callLogBlfEnabled>
</commonProfile>
<loadInformation>SIP45.8-5-4S</loadInformation>
<vendorConfig>
<disableSpeaker>false</disableSpeaker>
<disableSpeakerAndHeadset>false</disableSpeakerAndHeadset>
<pcPort>0</pcPort>
<settingsAccess>1</settingsAccess>
<garp>0</garp>
<voiceVlanAccess>0</voiceVlanAccess>
<videoCapability>0</videoCapability>
<autoSelectLineEnable>0</autoSelectLineEnable>
<webAccess>0</webAccess>
<daysDisplayNotActive>1,2,3,4,5,6,7</daysDisplayNotActive>
<displayOnTime>00:00</displayOnTime>
<displayOnDuration>00:00</displayOnDuration>
<displayIdleTimeout>00:00</displayIdleTimeout>
<spanToPCPort>1</spanToPCPort>
<loggingDisplay>1</loggingDisplay>
<loadServer></loadServer>
</vendorConfig>
<userLocale>
<name></name>
<uid></uid>
<langCode>en_US</langCode>
<version>1.0.0.0-1</version>
<winCharSet>iso-8859-1</winCharSet>
</userLocale>
<networkLocale></networkLocale>
<networkLocaleInfo>
<name></name>
<uid></uid>
<version>1.0.0.0-1</version>
</networkLocaleInfo>
<deviceSecurityMode>1</deviceSecurityMode>
<authenticationURL>http://example.domain.ext/services/authenticate.php</authenticationURL>
<directoryURL>http://example.domain.ext/services/directory.php</directoryURL>
<servicesURL>http://example.domain.ext/services/menu.xml</servicesURL>
<idleURL></idleURL>
<informationURL></informationURL>
<messagesURL></messagesURL>
<proxyServerURL></proxyServerURL>
<dscpForSCCPPhoneConfig>96</dscpForSCCPPhoneConfig>
<dscpForSCCPPhoneServices>0</dscpForSCCPPhoneServices>
<dscpForCm2Dvce>96</dscpForCm2Dvce>
<transportLayerProtocol>4</transportLayerProtocol>
<capfAuthMode>0</capfAuthMode>
<capfList>
<capf>
<phonePort>3804</phonePort>
</capf>
</capfList>
<certHash></certHash>
<encrConfig>false</encrConfig>
</device>Hi Godfrey,
Could you please collect packet capture from the back of the phone when it tries to register using the link:
https://supportforums.cisco.com/document/44741/collecting-packet-capture-cisco-ip-phone
If the IP phone port is not spanned, then you have to collect the sniffers from the switchport where the phone is connected to. You have to span the switch port and collect the sniffer captures
~Amit -
Cisco SIP Phone 9971 won't register on CME 8.6 or 8.5 Please HELP
Please help me , I have problem with registering Cisco SIP phone 9971 with CME 8.6 on ISR 2901.
I configured CME for SIP clients, then I add configuration for 9971 phone and create profiles. Phone downloaded SEP...xml file from CME,after that phone look for g4-tones.xml and gd-sip.jar files, I added them to CME after that phone downloaded them and reboot. Now phone is stuck in some kind of loop and does not register on CME.
On phone log I can see repeting next few messeges.
12:01:58a No DNS Server IP
12:01:59a Updating Trust list
12:01:59a No Trust List instaled
12:01:59a SEP04C5AB03B0D.cnf.xml (TFTP) // at this time phone download SEP...xml file from CME
12:02:00a VPN Error: VPN is not Configured
on CME if issue DEBUG TFTP EVENTS i receive next few lines
*Aug 18 18:20:19.891: TFTP: Looking for CTLSEP04C5A4B03B0D.tlv
*Aug 18 18:20:19.987: TFTP: Looking for ITLSEP04C5A4B03B0D.tlv
*Aug 18 18:20:20.083: TFTP: Looking for ITLFile.tlv
*Aug 18 18:20:20.347: TFTP: Looking for SEP04C5A4B03B0D.cnf.xml
*Aug 18 18:20:20.351: TFTP: Opened flash:/SEP04C5A4B03B0D.cnf.xml, fd 14, size 4585 for process 141
*Aug 18 18:20:20.363: TFTP: Finished flash:/SEP04C5A4B03B0D.cnf.xml, time 00:00:00 for process 141
here you can see verison info of CME
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 24-Mar-11 15:31 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE (fc1)
ELTOSAN_ROUTER uptime is 1 hour, 50 minutes
System returned to ROM by reload at 16:29:20 UTC Thu Aug 18 2011
System image file is "flash:/c2900-universalk9-mz.SPA.151-4.M.bin"
Last reload type: Normal Reload
Last reload reason: Reload Command
Cisco CISCO2901/K9 (revision 1.0) with 471040K/53248K bytes of memory.
Processor board ID FGL1508252Y
3 Gigabit Ethernet interfaces
2 terminal lines
1 Virtual Private Network (VPN) Module
4 Voice FXO interfaces
4 Voice FXS interfaces
1 Internal Services Module (ISM) with Services Ready Engine (SRE)
Survivable Remote Site Voicemail (SRSV) on Cisco Unity Express (CUE) 8.5.1 in slot/sub-slot 0/0
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
254464K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device# PID SN
*0 CISCO2901/K9 xxxxxxxxxxxxx
Technology Package License Information for Module:'c2900'
Technology Technology-package Technology-package
Current Type Next reboot
ipbase ipbasek9 Permanent ipbasek9
security securityk9 Permanent securityk9
uc uck9 Permanent uck9
data None None None
Configuration register is 0x2102
this is RUNNING CONFIGURATION
! Last configuration change at 16:10:12 UTC Thu Aug 18 2011
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname ELTOSAN_ROUTER
boot-start-marker
boot system flash:/c2900-universalk9-mz.SPA.151-4.M.bin
boot-end-marker
no aaa new-model
no ipv6 cef
ip source-route
no ip routing
no ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.5.1 192.168.5.10
ip dhcp excluded-address 192.168.5.200 192.168.5.255
ip dhcp pool phone
network 192.168.5.0 255.255.255.0
default-router 192.168.5.251
option 150 ip 192.168.5.251
ip dhcp pool data
relay source 192.168.2.0 255.255.255.0
relay destination 192.168.2.201
multilink bundle-name authenticated
crypto pki token default removal timeout 0
voice-card 0
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
fax protocol pass-through g711alaw
sip
registrar server expires max 3600 min 120
voice register global
mode cme
source-address 192.168.5.251 port 5060
max-dn 6
max-pool 6
load 9971 sip9971.9-1-1SR1.loads
authenticate register
tftp-path flash:
create profile sync 0005135312289902
voice register dn 1
number 207
allow watch
name GossaVM
label 207
voice register dn 3
number 101
name Dejan
label 101
mwi
voice register pool 1
id mac 000C.29C5.0011
number 1 dn 1
dtmf-relay sip-notify
username testvm password testera
codec g711alaw
voice register pool 3
id mac 04C5.A4B0.3B0D
type 9971
number 3 dn 3
presence call-list
dtmf-relay rtp-nte
username dejan password 1234
codec g711alaw
no vad
license udi pid CISCO2901/K9 sn xxxxxxxxxxxx
hw-module ism 0
hw-module pvdm 0/0
redundancy
interface GigabitEthernet0/0
description INTERFACE INTERNAL
no ip address
no ip route-cache
duplex auto
speed auto
no mop enabled
interface GigabitEthernet0/0.2
description LAN DATA
encapsulation dot1Q 2
ip address 192.168.2.251 255.255.255.0
no ip route-cache
interface GigabitEthernet0/0.5
description LAN VOICE
encapsulation dot1Q 5
ip address 192.168.5.251 255.255.255.0
no ip route-cache
interface ISM0/0
no ip address
no ip route-cache
shutdown
!Application: SRSV-CUE Running on ISM
interface GigabitEthernet0/1
no ip address
no ip route-cache
shutdown
duplex auto
speed auto
interface ISM0/1
description Internal switch interface connected to Internal Service Module
shutdown
interface Vlan1
no ip address
no ip route-cache
shutdown
ip forward-protocol nd
no ip http server
no ip http secure-server
snmp-server community public RO
tftp-server flash:dkern9971.100609R2-9-1-1SR1.sebn alias dkern9971.100609R2-9-1-1SR1.sebn
tftp-server flash:kern9971.9-1-1SR1.sebn alias kern9971.9-1-1SR1.sebn
tftp-server flash:rootfs9971.9-1-1SR1.sebn alias rootfs9971.9-1-1SR1.sebn
tftp-server flash:sboot9971.031610R1-9-1-1SR1.sebn alias sboot9971.031610R1-9-1-1SR1.sebn
tftp-server flash:skern9971.022809R2-9-1-1SR1.sebn alias skern9971.022809R2-9-1-1SR1.sebn
tftp-server flash:sip9971.9-1-1SR1.loads alias sip9971.9-1-1SR1.loads
tftp-server flash:United_States/g4-tones.xml
tftp-server flash:English_United_States/gd-sip.jar
control-plane
voice-port 0/0/0
voice-port 0/0/1
voice-port 0/0/2
voice-port 0/0/3
voice-port 0/1/0
voice-port 0/1/1
voice-port 0/1/2
voice-port 0/1/3
mgcp profile default
gatekeeper
shutdown
line con 0
line aux 0
line 67
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
password jebiga
login
transport input all
end
I did not have any kind of problem with X-LITE to register to CME. also try with few SCCP phones 7940 and I did not any kind of problem .
this is content of SEP....xml file for 9971
<device>
<deviceProtocol>SIP</deviceProtocol>
<devicePool>
<dateTimeSetting>
<dateTemplate>M/D/YA</dateTemplate>
<timeZone>Pacific Standard/Daylight Time</timeZone>
<ntps>
<ntp priority="0">
<name>0.0.0.0</name>
<ntpMode>unicast</ntpMode>
</ntp>
</ntps>
</dateTimeSetting>
<callManagerGroup>
<members>
<member priority="0">
<callManager>
<ports>
<sipPort>5060</sipPort>
</ports>
<processNodeName>192.168.5.251</processNodeName>
</callManager>
</member>
</members>
</callManagerGroup>
</devicePool>
<sipProfile>
<sipProxies>
<registerWithProxy>true</registerWithProxy>
</sipProxies>
<sipCallFeatures>
<cnfJoinEnabled>true</cnfJoinEnabled>
<localCfwdEnable>true</localCfwdEnable>
<callForwardURI>service-uri-cfwdall</callForwardURI>
<callPickupURI>service-uri-pickup</callPickupURI>
<callPickupGroupURI>service-uri-gpickup</callPickupGroupURI>
<callHoldRingback>2</callHoldRingback>
<semiAttendedTransfer>true</semiAttendedTransfer>
<anonymousCallBlock>2</anonymousCallBlock>
<callerIdBlocking>2</callerIdBlocking>
<dndControl>2</dndControl>
<remoteCcEnable>true</remoteCcEnable>
</sipCallFeatures>
<sipStack>
<remotePartyID>true</remotePartyID>
</sipStack>
<sipLines>
<line button="1" lineIndex="1">
<featureID>9</featureID>
<featureLabel></featureLabel>
<proxy>USECALLMANAGER</proxy>
<port>5060</port>
<name></name>
<displayName></displayName>
<autoAnswer>
<autoAnswerEnabled>2</autoAnswerEnabled>
</autoAnswer>
<callWaiting>1</callWaiting>
<authName>dejan</authName>
<authPassword>1234</authPassword>
<sharedLine>false</sharedLine>
<messagesNumber></messagesNumber>
<ringSettingActive>5</ringSettingActive>
<forwardCallInfoDisplay>
<callerName>true</callerName>
<callerNumber>true</callerNumber>
<redirectedNumber>true</redirectedNumber>
<dialedNumber>true</dialedNumber>
</forwardCallInfoDisplay>
</line>
<line button="2" lineIndex="2">
<featureID>9</featureID>
<featureLabel>101</featureLabel>
<proxy>USECALLMANAGER</proxy>
<port>5060</port>
<name>101</name>
<displayName>Dejan Rakic</displayName>
<autoAnswer>
<autoAnswerEnabled>2</autoAnswerEnabled>
</autoAnswer>
<callWaiting>1</callWaiting>
<authName>dejan</authName>
<authPassword>1234</authPassword>
<sharedLine>false</sharedLine>
<messagesNumber></messagesNumber>
<ringSettingActive>5</ringSettingActive>
<forwardCallInfoDisplay>
<callerName>true</callerName>
<callerNumber>true</callerNumber>
<redirectedNumber>true</redirectedNumber>
<dialedNumber>true</dialedNumber>
</forwardCallInfoDisplay>
</line>
</sipLines>
<enableVad>true</enableVad>
<preferredCodec>g711alaw</preferredCodec>
<dialTemplate></dialTemplate>
<kpml>1</kpml>
<phoneLabel></phoneLabel>
<stutterMsgWaiting>2</stutterMsgWaiting>
<disableLocalSpeedDialConfig>true</disableLocalSpeedDialConfig>
<dscpForAudio>184</dscpForAudio>
<dscpVideo>136</dscpVideo>
</sipProfile>
<commonProfile>
<phonePassword>1234</phonePassword>
<callLogBlfEnabled>2</callLogBlfEnabled>
</commonProfile>
<featurePolicyFile>featurePolicyDefault.xml</featurePolicyFile>
<loadInformation>sip9971.9-1-1SR1.loads</loadInformation>
<vendorConfig>
</vendorConfig>
<commonConfig>
<videoCapability>0</videoCapability>
<ciscoCamera>0</ciscoCamera>
</commonConfig>
<sshUserId>dejan</sshUserId>
<sshPassword>1234</sshPassword>
<userId></userId>
<phoneServices>
<provisioning>2</provisioning>
<phoneService type="1" category="0">
<name>Missed Calls</name>
<phoneLabel></phoneLabel>
<url>Application:Cisco/MissedCalls</url>
<vendor></vendor>
<version></version>
</phoneService>
<phoneService type="1" category="0">
<name>Received Calls</name>
<phoneLabel></phoneLabel>
<url>Application:Cisco/ReceivedCalls</url>
<vendor></vendor>
<version></version>
</phoneService>
<phoneService type="1" category="0">
<name>Placed Calls</name>
<phoneLabel></phoneLabel>
<url>Application:Cisco/PlacedCalls</url>
<vendor></vendor>
<version></version>
</phoneService>
<phoneService type="2" category="0">
<name>Voicemail</name>
<phoneLabel></phoneLabel>
<url>Application:Cisco/Voicemail</url>
<vendor></vendor>
<version></version>
</phoneService>
</phoneServices>
<versionStamp>0131511014412102</versionStamp>
<userLocale>
<name>English_United_States</name>
<langCode>en</langCode>
</userLocale>
<networkLocale>United_States</networkLocale>
<networkLocaleInfo>
<name>United_States</name>
</networkLocaleInfo>
<authenticationURL></authenticationURL>
<directoryURL></directoryURL>
<servicesURL>http://192.168.5.251:80/CMEserverForPhone/serviceurl</servicesURL>
<dscpForSCCPPhoneServices>0</dscpForSCCPPhoneServices>
<dscpForCm2Dvce>96</dscpForCm2Dvce>
<transportLayerProtocol>2</transportLayerProtocol>
</device>Hello,
I'm facing exactly the same problem, that is:
a Cisco SIP Phone 9971 won't register on CME 8.6 running on a 2811
I have read all the postings to this Forum, but I have not been able to solve it.
In my case the commands voice register dn and voice register pool are OK.
So frankly, I have no idea what I could be missing.
I'm pasting the Router's config.
I hope somebody is able to point me in the right direction.
Here is the config. Thank you!
C2811#sh run
Building configuration...
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname C2811
no aaa new-model
dot11 syslog
ip source-route
ip cef
ip dhcp excluded-address 172.25.140.1 172.25.140.10
ip dhcp excluded-address 172.35.140.1 172.35.140.10
ip dhcp pool Data
network 172.25.140.0 255.255.255.0
default-router 172.25.140.1
option 150 ip 172.25.140.1
dns-server 172.25.140.1
ip dhcp pool Voice
network 172.35.140.0 255.255.255.0
default-router 172.35.140.1
option 150 ip 172.35.140.1
dns-server 172.35.140.1
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
voice service voip
allow-connections sip to sip
sip
registrar server expires max 3600 min 120
voice register global
mode cme
source-address 172.25.140.1 port 5060
max-dn 40
max-pool 42
load 9971 sip9971.9-4-1-9.loads
authenticate register
authenticate realm cisco
tftp-path flash:
create profile sync 0004820400584603
voice register dn 1
number 1010
allow watch
name Phone10
label Phone10
mwi
voice register pool 1
id mac 189C.5DB6.BD09
type 9971
number 1 dn 1
presence call-list
dtmf-relay rtp-nte
username adm password adm
call-forward b2bua busy 68600
codec g711ulaw
no vad
camera
video
voice-card 0
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-1879153754
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1879153754
revocation-check none
rsakeypair TP-self-signed-1879153754
crypto pki certificate chain TP-self-signed-1879153754
certificate self-signed 01
(details ommited)
license udi pid CISCO2811 sn FTX1146A44H
username admin privilege 15 password 0 admin
redundancy
interface FastEthernet0/0
no ip address
duplex auto
speed auto
interface FastEthernet0/0.25
description Data VLAN
encapsulation dot1Q 25
ip address 172.25.140.1 255.255.255.0
interface FastEthernet0/0.35
description Voice VLAN
encapsulation dot1Q 35
ip address 172.35.140.1 255.255.255.0
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 600 life 86400 requests 10000
tftp-server flash:P00308010200.bin
tftp-server flash:P00308010200.sbn
tftp-server flash:P00308010200.sb2
tftp-server flash:P00308010200.loads
tftp-server flash:SCCP42.9-3-1SR3-1S.loads
tftp-server flash:apps42.9-3-1ES19.sbn
tftp-server flash:cnu42.9-3-1ES19.sbn
tftp-server flash:cvm42sccp.9-3-1ES19.sbn
tftp-server flash:dsp42.9-3-1ES19.sbn
tftp-server flash:jar42sccp.9-3-1ES19.sbn
tftp-server flash:term42.default.loads
tftp-server flash:term62.default.loads
tftp-server flash:SCCP45.9-3-1SR3-1S.loads
tftp-server flash:apps45.9-3-1ES19.sbn
tftp-server flash:cnu45.9-3-1ES19.sbn
tftp-server flash:cvm45sccp.9-3-1ES19.sbn
tftp-server flash:dsp45.9-3-1ES19.sbn
tftp-server flash:jar45sccp.9-3-1ES19.sbn
tftp-server flash:term45.default.loads
tftp-server flash:term65.default.loads
tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
ml
tftp-server flash:sip9971.9-4-1-9.loads
tftp-server flash:kern9971.9-4-1-9.sebn
tftp-server flash:rootfs9971.9-4-1-9.sebn
tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
control-plane
mgcp profile default
telephony-service
max-ephones 24
max-dn 48
ip source-address 172.25.140.1 port 2000
cnf-file location flash:
load 7960-7940 P00308010200
load 7942 SCCP42.9-3-1SR3-1S.loads
load 7945 SCCP45.9-3-1SR3-1S.loads
load 7962 SCCP42.9-3-1SR3-1S.loads
load 7965 SCCP45.9-3-1SR3-1S.loads
max-conferences 8 gain -6
dn-webedit
transfer-system full-consult
create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
ephone-dn 1
number 1001
description Phone 1
name Phone 1
hold-alert 30 originator
ephone-dn 2
number 1002
description Phone 2
name Phone 2
hold-alert 30 originator
ephone-dn 3
number 1003
description Phone 3
name Phone 3
hold-alert 30 originator
ephone 1
device-security-mode none
mac-address 001C.58FB.6E0F
button 1:1
ephone 2
device-security-mode none
mac-address 0014.A981.7F8A
button 1:2
ephone 3
device-security-mode none
mac-address 0006.5356.A4B8
button 1:3
alias exec con conf t
alias exec sib show ip int brief
alias exec srb show run | b
alias exec sri show run int
line con 0
exec-timeout 0 0
logging synchronous
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
transport output telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
transport output telnet ssh
scheduler allocate 20000 1000
ntp master 1
end
C2811# -
Cisco SIP Phone 9971 won't register on CME 8.6
Hello,
I'm facing a very strange problem:
a Cisco SIP Phone 9971 won't register on CME 8.6 running on a 2811
I have read all the related-postings to this and other Forum, but I have not been able to solve it.
One of the "potential solutions" was to make sure that the Phone had a Line configured.
But I think that the commands voice register dn and voice register pool are properly configured (see config below)
So frankly, I have no idea what I could be missing.
I'm pasting the Router's config.
I hope somebody is able to point me in the right direction.
Here is the config. Thank you!
C2811#sh run
Building configuration...
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname C2811
no aaa new-model
dot11 syslog
ip source-route
ip cef
ip dhcp excluded-address 172.25.140.1 172.25.140.10
ip dhcp excluded-address 172.35.140.1 172.35.140.10
ip dhcp pool Data
network 172.25.140.0 255.255.255.0
default-router 172.25.140.1
option 150 ip 172.25.140.1
dns-server 172.25.140.1
ip dhcp pool Voice
network 172.35.140.0 255.255.255.0
default-router 172.35.140.1
option 150 ip 172.35.140.1
dns-server 172.35.140.1
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
voice service voip
allow-connections sip to sip
sip
registrar server expires max 3600 min 120
voice register global
mode cme
source-address 172.25.140.1 port 5060
max-dn 40
max-pool 42
load 9971 sip9971.9-4-1-9.loads
authenticate register
authenticate realm cisco
tftp-path flash:
create profile sync 0004820400584603
voice register dn 1
number 1010
allow watch
name Phone10
label Phone10
mwi
voice register pool 1
id mac 189C.5DB6.BD09
type 9971
number 1 dn 1
presence call-list
dtmf-relay rtp-nte
username adm password adm
call-forward b2bua busy 68600
codec g711ulaw
no vad
camera
video
voice-card 0
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-1879153754
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1879153754
revocation-check none
rsakeypair TP-self-signed-1879153754
crypto pki certificate chain TP-self-signed-1879153754
certificate self-signed 01
(details ommited)
license udi pid CISCO2811 sn FTX1146A44H
username admin privilege 15 password 0 admin
redundancy
interface FastEthernet0/0
no ip address
duplex auto
speed auto
interface FastEthernet0/0.25
description Data VLAN
encapsulation dot1Q 25
ip address 172.25.140.1 255.255.255.0
interface FastEthernet0/0.35
description Voice VLAN
encapsulation dot1Q 35
ip address 172.35.140.1 255.255.255.0
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 600 life 86400 requests 10000
tftp-server flash:P00308010200.bin
tftp-server flash:P00308010200.sbn
tftp-server flash:P00308010200.sb2
tftp-server flash:P00308010200.loads
tftp-server flash:SCCP42.9-3-1SR3-1S.loads
tftp-server flash:apps42.9-3-1ES19.sbn
tftp-server flash:cnu42.9-3-1ES19.sbn
tftp-server flash:cvm42sccp.9-3-1ES19.sbn
tftp-server flash:dsp42.9-3-1ES19.sbn
tftp-server flash:jar42sccp.9-3-1ES19.sbn
tftp-server flash:term42.default.loads
tftp-server flash:term62.default.loads
tftp-server flash:SCCP45.9-3-1SR3-1S.loads
tftp-server flash:apps45.9-3-1ES19.sbn
tftp-server flash:cnu45.9-3-1ES19.sbn
tftp-server flash:cvm45sccp.9-3-1ES19.sbn
tftp-server flash:dsp45.9-3-1ES19.sbn
tftp-server flash:jar45sccp.9-3-1ES19.sbn
tftp-server flash:term45.default.loads
tftp-server flash:term65.default.loads
tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
ml
tftp-server flash:sip9971.9-4-1-9.loads
tftp-server flash:kern9971.9-4-1-9.sebn
tftp-server flash:rootfs9971.9-4-1-9.sebn
tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
control-plane
mgcp profile default
telephony-service
max-ephones 24
max-dn 48
ip source-address 172.25.140.1 port 2000
cnf-file location flash:
load 7960-7940 P00308010200
load 7942 SCCP42.9-3-1SR3-1S.loads
load 7945 SCCP45.9-3-1SR3-1S.loads
load 7962 SCCP42.9-3-1SR3-1S.loads
load 7965 SCCP45.9-3-1SR3-1S.loads
max-conferences 8 gain -6
dn-webedit
transfer-system full-consult
create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
ephone-dn 1
number 1001
description Phone 1
name Phone 1
hold-alert 30 originator
ephone-dn 2
number 1002
description Phone 2
name Phone 2
hold-alert 30 originator
ephone-dn 3
number 1003
description Phone 3
name Phone 3
hold-alert 30 originator
ephone 1
device-security-mode none
mac-address 001C.58FB.6E0F
button 1:1
ephone 2
device-security-mode none
mac-address 0014.A981.7F8A
button 1:2
ephone 3
device-security-mode none
mac-address 0006.5356.A4B8
button 1:3
alias exec con conf t
alias exec sib show ip int brief
alias exec srb show run | b
alias exec sri show run int
line con 0
exec-timeout 0 0
logging synchronous
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
transport output telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
transport output telnet ssh
scheduler allocate 20000 1000
ntp master 1
end
C2811#Thank you for your reply.
I did some debugs and the results are very strange!
This is what I got:
Feb 24 18:01:12.219: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 400 Bad Request
Via: SIP/2.0/UDP 172.35.140.12:5060;branch=z9hG4bK08011844
From: ;tag=189c5db6bd09000260cf3daf-289a76d1
To: ;tag=52488-160A
Date: Mon, 24 Feb 2014 18:01:12 GMT
Call-ID: [email protected]
CSeq: 1000 REFER
Content-Length: 0
Contact:
Feb 24 18:01:12.291: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Received:
REGISTER sip:172.25.140.1 SIP/2.0
Via: SIP/2.0/UDP 172.35.140.12:5060;branch=z9hG4bK1e9ad079
From: ;tag=189c5db6bd0900032df02e9c-25d79707
To:
Call-ID: [email protected]
Max-Forwards: 70
Date: Fri, 01 Jan 1982 00:02:41 GMT
CSeq: 101 REGISTER
User-Agent: Cisco-CP9971/9.4.1
Contact: ;+sip.instance="
000000-0000-0000-0000-189c5db6bd09>";+u.sip!devicename.ccm.cisco.com="SEP189C5DB
6BD09";+u.sip!model.ccm.cisco.com="493";video
Supported: replaces,join,sdp-anat,norefersub,resource-priority,extended-refer,X-
cisco-callinfo,X-cisco-serviceuri,X-cisco-escapecodes,X-cisco-service-control,X-
cisco-srtp-fallback,X-cisco-monrec,X-cisco-config,X-cisco-sis-6.0.2,X-cisco-xsi-
8.0.1
Content-Length: 0
Reason: SIP;cause=200;text="cisco-alarm:22 Name=SEP189C5DB6BD09 ActiveLoad=sip99
71.9-4-1-9.loads InactiveLoad=sip9971.9-3-2SR1-1.loads Last=reset-reset"
Expires: 3600
Feb 24 18:01:12.395: voice_reg_get_reg_expires_timer: no voice register pool found
Feb 24 18:01:12.395: VOICE_REG_POOL: Register request for (1010) from (172.35.140.12)
Feb 24 18:01:12.395: VOICE_REG_POOL: Contact matches pool 1 number list 1
Feb 24 18:01:12.395: VOICE_REG_POOL: No entry for (172.35.140.12) found in srst contact table
Feb 24 18:01:12.395: VOICE_REG_POOL: key(1010) contact(172.35.140.12:5060) add to contact table
Feb 24 18:01:12.395: VOICE_REG_POOL: No entry for (1010) found in contact table
Feb 24 18:01:12.399: VOICE_REG_POOL: key(1010) contact(172.35.140.12) added to contact table
Feb 24 18:01:12.399: VOICE_REG_POOL: key(172.35.140.12) contact(1010) add to srst contact table
Feb 24 18:01:12.399: VOICE_REG_POOL: No entry for (172.35.140.12) found in srst contact table
Feb 24 18:01:12.399: VOICE_REG_POOL: key(172.35.140.12) contact(1010) added to srst contact table
Feb 24 18:01:12.399: VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
But right after these errors, I get the following:
Feb 24 18:01:12.399: VOICE_REG_POOL: Creating param container for dial-peer 4000
1.VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
VOICE_REG_POOL pool_tag(1), dn_tag(1)
Feb 24 18:01:12.399: VOICE_REG_POOL: Created dial-peer entry of type 0
Feb 24 18:01:12.399: VOICE_REG_POOL: Registration successful for 1010, registration id is 1
Feb 24 18:01:12.411: VOICE_REG_POOL: Contact matches pool 1 number list 1
Feb 24 18:01:12.411: VOICE_REG_POOL: GW SIS: X-cisco-cme-sis-1.0.0
Feb 24 18:01:12.411: VOICE REGISTER POOL-1 has registered.
Name:SEP189C5DB6BD09 IP:172.35.140.12 DeviceType:Phone
Feb 24 18:01:12.411: VOICE_REG_POOL: Pool[1]: service-control (reset type: 2) message sent to sip:[email protected]
Feb 24 18:01:12.411: voice_reg_privacy_update_to_phone: delay sending privacy update during bulk registration
Feb 24 18:01:12.415: //1/7B0070C28003/SIP/Msg/ccsipDisplayMsg:
====================
And when I do a sh voice register pool, I get the following:
C2811#sh voice register pool 1
Pool Tag 1
Config:
Mac address is 189C.5DB6.BD09
Type is 9971
Number list 1 : DN 1
Proxy Ip address is 0.0.0.0
Current Phone load version is Cisco-CP9971/9.4.1
DTMF Relay is enabled, rtp-nte
Call Waiting is enabled
DnD is disabled
Video is enabled
Camera is enabled
Busy trigger per button value is 0
call-forward b2bua busy 68600
keep-conference is enabled
registration expires timer max is 3600 and min is 120
username adm password adm
kpml signal is enabled
Lpcor Type is none
blf call list is enabled
Transport type is udp
service-control mechanism is supported
registration Call ID is [email protected]
Registration method: per line
Privacy feature is not configured.
Privacy button is disabled
active primary line is: 1010
contact IP address: 172.35.140.12 port 5060
Phone SIS Version: 6.0.2
GW SIS Version: 1.0.0
Dialpeers created:
Dial-peers for Pool 1:
dial-peer voice 40001 voip
destination-pattern 1010
session target ipv4:172.35.140.12:5060
session protocol sipv2
dtmf-relay rtp-nte
digit collect kpml
codec g711ulaw bytes 160
no vad
call-fwd-busy 68600
after-hours-exempt FALSE
Statistics:
Active registrations : 4
Total SIP phones registered: 1
Total Registration Statistics
Registration requests : 4
Registration success : 4
Registration failed : 0
unRegister requests : 0
unRegister success : 0
unRegister failed : 0
Attempts to register
after last unregister : 0
Last register request time : 18:11:43.551 UTC Mon Feb 24 2014
Last unregister request time :
Register success time : 18:11:43.551 UTC Mon Feb 24 2014
Unregister success time :
C2811#
So apparently the Phone is actually registered!
However, the Phone screens still shows this message: Phone Not Registered.
So frankly I don't understand what's going on!
I really hope somebody can help. Thanks!
Maybe you are looking for
-
Using one copy of Windows to install via boot camp and on a virtual machine?
I have a copy on windows 7 coming in the post and I was wondering if it is possible to install windows 7 via boot camp when I want to do something more memory intensive such as gaming and also install it on a virtual machine such as virtual box just
-
Mac G4 Won't Boot Completely After Restart
I fired up my Mac G4 and ran software update and installed the 10.4.11 update. When I restarted to complete the install the computer gets hung up -- a blue screen with the gear icon turning and turning. It worked fine before I did the update. I've re
-
Recovering iPhone data after crashed HD.
I lost my computer HD and my iPhone backup was not updated. How do I get my data back from the iPhone (contacts, pictures)? Apps and Music is connected to the app store, but the rest? I'm a Mac OS X user.
-
How to delete my posts on this forum
Hi, Can someone tell me how I can delete my posts and any reply's to them, as people googling the site name can see the posts and my issues. This including a client who is very upset that they can all be seen. Thanks, help needed urgently. Annie
-
Is there any tool that lets you control your iPhone from a PC? I have a friend who recently purchased an iPhone but lives far away and needs help setting up a few things. I was thinking if there was something you could use to show the screen and cont