Cisco ip phones and cme help

Hi,
Ina company which uses cisco call manager express with ip phones 7931, 7945 ,7975, 7911,7962…….
1- i want the configuration in which the user dial a pin code befor doing an outside call...?
2- i want to change the defalt configuration for the ip phones of days backlight not active to thursday and friday and the backlight in duration to 1:30.?
i did the followings commands but it doesn`t take an effect.
Router(config)# telephony-service
Router(config-telephony)# service phone daysBacklightNotActive 6
Router(config-telephony)# service phone backlightOnDuration 1:30
Router(config-telephony)# service phone backlightIdleTimeout 01:00
Router(config-telephony)# create cnf-files
Router(config-telephony)# reset all
3- i have ringtones files in the flash (sh flash attached) , i want all the ringtones appear on all the ip phones when i press settings then user prefrences and then rings- i can only see two ring tones.
thanks for your help

My reply may be too late to be of any help to you, but for the benefit of others:
Be sure you understand the different types of PoE out there. The Linksys PoE switch only supports the newer IEEE 802.3af PoE standard.
The 7940, 7960, 7905 and other older Cisco phones only support Cisco pre-standard PoE and thus will not work with the 802.3af Linksys Switch.
To use this switch, you will need to make sure you are using the newer 7070, 7961, 7941 phones with support both pre-standard and 802.3af PoE.
All the best,
John

Similar Messages

  • Recording for Cisco IP Phones and Cisco C90 Codec

    Hello
    We are looking for a solution that is capable to record both Cisco IP Phones and Cisco Codec C90.
    We are using CUCM 9.X for IP Phones and VCS 7.X for Cisco Codecs.
    Is their any third party solution available for both the requirements or do i have to go with TCS and any other third party recording solution.
    Thanks & Regards
    Aniket Patil

    My reply may be too late to be of any help to you, but for the benefit of others:
    Be sure you understand the different types of PoE out there. The Linksys PoE switch only supports the newer IEEE 802.3af PoE standard.
    The 7940, 7960, 7905 and other older Cisco phones only support Cisco pre-standard PoE and thus will not work with the 802.3af Linksys Switch.
    To use this switch, you will need to make sure you are using the newer 7070, 7961, 7941 phones with support both pre-standard and 802.3af PoE.
    All the best,
    John

  • Cisco ip phone and wired user authenticate form ISE

    Hi dears,
    I configurate wired users from Cisco ISE. The authentication protocol is Eap-fast, the external device is DC. The wired user authenticate from ISE normally. I use labminutes web sites for configuration video.
    Now the customer also want the cisco phone is authenticate from ISE. the physical connection is that: the cable connect to phone from switch. and one cable is connec from phone to pc.(standard physiacl connection.)
    I create new authentication policy and use mab, and  new authorization police.
    The problem is : the phone is authenticate is normally but the wired user want to authenticate but it can not authenticate.
    Can someone provide me a best practice configuration on ise and switch for phone and wired user authentication. or please say the source of problem.
    Thanks.

    interface GigabitEthernet1/0/48
     switchport access vlan 10
     switchport mode access
     switchport voice vlan 14
     ip access-group ACL-ALLOW in
     authentication event fail action next-method
     authentication event server dead action authorize vlan 20
     authentication event server alive action reinitialize
     authentication host-mode multi-auth
     authentication open
     authentication order dot1x mab
     authentication priority dot1x mab
     authentication port-control auto
     authentication periodic
     authentication timer reauthenticate server
     authentication violation restrict
     mab
     dot1x pae authenticator
     dot1x timeout tx-period 10
     spanning-tree portfast
    do you need ISE configuration??

  • Cisco 6921 Phones and CUCM 6.1

    We have bought some new 6921 Phones and want to know if I can use them on my CUCM 6.1.2.1000-13
    Are there instuctions?
    The phone does not appear in the Device Default list.
    Thank You
    Matt

    Hello,
    Already replied in another thread. Anyway, CallManager and CallManager Express (e.g. IOS gateways) support CDRs.
    Hope it helps, please rate if it does.
    Kind regards,
    - Adrian.

  • HT1766 I was attempting to backup my iphone 5 getting ready to update it to ios 7 and i accodentally restored it to the settings of my last phone which was an iphone 4s and it erased all my new pictures and info off my new phone and need help getting them

    I was attempting to backup my iphone 5 getting ready to update it to ios 7 and i accidentally restored it to the settings of my last phone which was an iphone 4s and it erased all my new pictures and info off my new phone and was wondering if anyone knows how i can get them back and restore it back like i has it?  Thanks

    That means you have not a backup before accidentally restore your new iPhone 5.
    So you should recover your new pictures and info with a third recovery tool.
    This blog has a useful tool to meet you.
    http://easy-iphone-recovery.blogspot.com/2013/09/iphone-recovery-resource.html
    In step 1, you should choose 'Recover from iOS Device' in the main interface and then following the steps to get your pictures and info back.
    Good Luck.

  • Transfer VOIP Calls Between Cisco Desk Phone and Cisco Jabber For IPhone 9.5

    Does anyone know how to transfer an active voip call from a Cisco IP Desk Phone to Cisco Jabber for IPhone?  I can transfer a call from Cisco Jabber for IPhone to my Cisco IP Desk Phone no problem.  I put the call on hold and then click "Resume" on my Cisco IP Desk Phone.  However I cannot do the same but the other way around.  If I put the call on hold on my Cisco IP Desk Phone, I see "no active call" on my Jabber client.  The only information I could find slighlty relevant was using the Mobility Key/Remote Destination Profile feature however this defeats the object as this will forward to an external number, e.g. mobile and I just want to transfer the call within the VOIP environment between the two devices that are using the same directory number.
    I am using Cisco Call Manager 9.1(2), Cisco Presence 9.1 and Cisco Jabber for IPhone 9.5.
    Any help would be greatly appreciated.
    Kind Regards,
    Paul Parker.

    Did you ever find an answer to this ?
    I am seeing the same behavior and trying so see if I can put calls on hold and pick them up both ways also.
    The only answer I seem to have found is to use park instead
    That would/should work but I would just prefer to hold/unhold
    Just not sure why we would not be able to hold/unhold on what is essentially a "shared" line
    Does anyone have this working for them ?

  • How to configure SGE2000P with CISCO 7900 phones and data VLAN

    Hello all
    I am having problem setting up SGE2000P switches to work with my default data VLAN and additional voice VLAN. I am configuring it to pick IP address for phones from voice VLAN which is working fine but when I connect a PC on phone port it is also picking up an IP from Voice VLAN while default VLAN is data with different scope of IP.
    Is there any good discussion or documents out there to help me resolve this issue before I pack these switches and purchase ESW 500 series. I have ESW 500 at another client and they are working fine out of the box but this guy is giving me hard time.
    Any suggestions help will be appreciated
    Mo

    HI Muhammed,
    I suggest you contact the Small Business Support Center for some help:
    http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
    Regards,
    Cindy Toy
    Cisco Small Business Community Manager
    for Cisco Small Business Products
    www.cisco.com/go/smallbizsupport
    twitter: CiscoSBsupport

  • Cisco CP7821 phone and CME10.0

    We have a brand new CME system and we have 2 CP7821 phone for common area's but i cant seem to find anything on how to get them to work. in fact when under telephony-service i run the "load ?" and that model is not even listed as a option. how then to i get those phones working?

    You may be able to add them as a generic SIP endpoint.  I don't have one of these phones in front of me but it should work as along as you can configure a SIP username/password on them.

  • I tried backing up my phone last night, it went on for 9 hours and then NOTHING happened? I got a new phone and need help

    What to do when your phone will not back up so you can transfer to a new device?

    If you have any iTunes Movies and TV Shows, remove them. iTunes Movies and TV Shows make up 75% of your backup time.
    example: Harry Potter and the Sorcerer's Stone takes up 4 GBs of iPhone Storage and costs 1-2 hours of backing up when it's on your hard drive.
    There's two ways to remove them if they're not necessary:
    iTunes - Phone Device - Checkbox "Only Sync Checked Music and Videos" below, then go to Movies and TV Shows tabs on iTunes itself and uncheck every single movie and TV show not needing to back up, then sync to remove them.
    iTunes - Phone Device - Movies and TV Shows - Sync "None" versus "Unwatched" or "All", then sync to remove them.
    Also, Video Camera movies if they are in your Photos. If they're on Camera Roll, remove those / move them to Photos. They take up large amounts of space.

  • I setup a Cisco Home Network and Need help Logging into It

    Hello, I have four 2521 routers and three 2954 switches.  I connected my ISPs modem from the ethernet port and plugged it into port 24 of one of my switches.  I also configured the switch for VTY access and gave it a login password.  I would like to log into the switch to configure it and telnet into all the other devices from a remote location.  But I am unable to ping the public address assigned to me by my ISP.  So I can't even telnet to the switch.  Help

    With help from elsewhere, I have learned how to change the colors and figured out a few other things. I have another question, though.
    I want to put a Twitter widget and a comment box on my website. I have the widget code from Twitter, but it is HTML and javascript or something. Can I just put these codes into the modules of the flash template? If you look at the template, you should see that it has modules that have editable HTML  text areas, but I don't know if it is limited to text or something, or if it will function correctly if I put other HTML codes in it such as script codes, etc in it.
    Also, if that works, does anyone know where I can get a code to put the comment box in one of the modules? I don't mean a contact box, I mean a widget where people can leave comments and the comments display on the page, like on a myspace profile. Just something simple that allows a visitor to leave a name and a text-only comment. I would also like to be able to selectively delete comments in case of spammers, etc.
    I found this, which might be what I am looking for, just a simple comment box, but this one is flash:
    http://activeden.net/item/commenting-with-no-database/69183?sso?WT.ac=search_item&WT.seg_1 =search_item&WT.z_author=flashBrian
    Message was edited by: ESJoeProductions

  • Cisco spa phone and '*' in the number

    Hello.
    I am set the phone dial plan (x.), but if i am enter the number ex:'45*' then phone show message "invalid number".
    How am i call to the number with "*" in middle?

    Try this Dial-Plan:
    (xx*|x.)
    Regards.

  • Cisco 6807 and 6800ia Swtich QOS for Cisco ip phones

    Does anyone have an example of configuring a 6800ia switch port connected to a 6807VSS parent for cisco ip phones qos.  Normally we'd use auto qos voip  but auto qos is not supported on 6800IA switches.
    Cant find any cisco documentation of what the IA switches port config should look like for a cisco ip phone.
    Any help would be appreciated.
    Thanks,
    Dave

    I'd leave QoS alone.

  • Cisco IP Phone 802.1x authentication with NPS

    Hi All,
    I would like to configure 802.1x authentication on both my Cisco ip phones and windows clients using NPS. So far i have tested the clients and it works however I am not finding any information on if NPS supports 802.1x on ip phones. Has anyone done a similar
    deployment using NPS. So far I am only seeing cisco ACS server being used as the policy server.

    Hi,
    Based on my research, it seems that you may enounter issues related to username(Basically Mircosoft only allows a 20 character user name, while the user name of the phone exceeds the 20 character limit and causes it to fail.) and certificate schema when
    configuring 802.1x authentication for Cisco IP phones.
    Best regards,
    Susie
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

  • 802.1x with Vlan assignment and IP phone and PC

    I have a Catalyst 4510R and I want to im plement 802.1x with dynamic VLAN assignment via Radius server. I am going to plug to switch ports Cisco IP phones and PCs (PCs are plugged in the IP phone).
    For this implementation I need to configure the switch port in mode trunk because I have voice vlan corresponding IP phone and data vlan corresponding to PC.
    However I have read that I can not enable 802.1x on a trunk port.
    How could I configure this?
    I need that when the PC is authenticated correctly is assigned to his cooresponding data vlan and the IP phone is in the voice vlan.
    Thanks

    You should configure the port as an access port with an aux-vlan. Here's an example:
    interface GigabitEthernet2/2
    switchport access vlan 701
    switchport mode access
    switchport voice vlan 702
    load-interval 30
    qos trust device cisco-phone
    qos trust cos
    auto qos voip cisco-phone
    dot1x pae authenticator
    dot1x port-control auto
    tx-queue 3
    bandwidth percent 33
    priority high
    shape percent 33
    spanning-tree portfast
    spanning-tree bpduguard enable
    service-policy output autoqos-voip-policy
    Hope this helps,

  • How can I connect a Cisco 7940 phone to a trixbox via SIP

    how can I connect a Cisco 7940 phone and CIsco 7970 to a trixbox via SIP

    ...by configuring the trixbox according to the required configuration and changing your firmware on the phones to SIP{
    =============================
    Please remember to rate useful posts, by clicking on the stars below.
    =============================

Maybe you are looking for

  • Ipod error -48

    Long time no visit! I haven't been here for a while coz all my ipod/itunes has been going so well - many updates went thru very easliy. Our household seems to be awash with ipods and 3 PCs running iTunes all very happily! However (groan!) I tried to

  • Set Tolerance Limits

    In this step, you specify the tolerance limits for each tolerance key for each company code. When processing an invoice, the R/3 System checks each item for variances between the invoice and the purchase order or goods receipt. The different types of

  • Withholding tax warning message

    Hi we maintain the witholding tax at invoice & payment level both in vendor master data, due to this system always deduct TDS twice at the time of posting. we want a check at the time of invociing and payment, system should ask about TDS whether this

  • URM Adapter

    Hi there, I've installed the URM Adapter for the first time, I want to Registering an External URM Source so I followed the instructions in the installation guide. The problem is that I'm a bit confused, I was wondering if someone can shed a light on

  • IPhone 3GS has gone completely dead, after telling me to connect to iTunes, after trying to update the software.

    My parents are about to recieve an upgrade to their contract which currently is an iPhone. They asked me to sync their iPhone to iTunes to save the settings, should they get an iPhone again. When I tried to sync the phone, iTunes prompted a software