Cisco IP SLA - RTTMON MIB - Problem setting values

Hi,
I am trying to use Cisco IP SLA to monitor QOS for voice data. I want to create a SLA operation from my NMS. I am using the RTTMON-MIB for this purpose. I was testing it out by creating an ICMP Echo operation, and I set the below values
rttMonCtrlAdminRttType.1 -Integer 9
rttMonEchoAdminProtocol.1 -Integer 27
rttMonEchoAdminTargetAddress.1 -OctetString "172.22.202.12"
rttMonEchoAdminTargetPort.1 -Integer 8000
rttMonEchoAdminInterval.1 -Integer 20
rttMonEchoAdminNumPackets.1 -Integer 100
rttMonCtrlAdminStatus.1 -Integer 4
rttMonScheduleAdminRttStartTime.1 -TimeTicks 1
rttMonScheduleAdminRttLife.1 -Integer 2147483647
I have set these values for an INDEX 1, using snmpset_requests. Can anyone tell me as to how do I go about with the indexing. I just chose 1 for the above eg and set the values. But I see the rttMonCtrlAdminIndex oid has not been updated with the new entry. Neither am I able to set the value of index as 1 for this oid using snmpset.
Can anyone please tell me how the indexing is done? Should I set the value of the index?
The other question is the format for the target ipadress? This OID accepts IP address as an Octet String. So '172.22.202.24' is ok? or should I convert it into some other format.
Regards
Roycey

The admin index is a random number which you must generate. It can be between 1 and 2147483647. Use your management station's pseudo-random number generator to pick an initial value. Then test it by polling rttMonCtrlAdminStatus for that index. If a row exists, pick a new index.
Yes, the IP address is of type OCTET STRING. You are setting it correctly.

Similar Messages

CISCO-RTTMON-MIB.my

In the MIB CISCO-RTTMON-MIB, for the notification 'rttMonLpdDiscoveryNotification', the first 2 varbinds are 'rttMplsVpnMonCtrlTag' and 'rttMonLpdGrpStatsTargetPE'. What's the diff b/w the two as both are addresses ?
Thanks in advance
Sunil

While both may be an address in your configuration, the two could be very different. The value of rttMplsVpnMonCtrlTag can be any string:
       "A string which is used by a managing application to
       identify the RTT target.       This string will be configured as rttMonCtrlAdminTag for all
       the operations configured by this Auto SAA L3 MPLS VPN.       The usage of this value in Auto SAA L3 MPLS VPN is same as
       rttMonCtrlAdminTag in RTT operation."
Where as the value of rttMonLpdGrpStatsTargetPE with also be an address.

Problem in Setting value in cells of jTable

I am trying to set values in the table by editing the cells, the problem is that once i enter some values in the cells and hit enter or click on next cell it gives an exception of stack overflow, i tried tracing i am getting all the values of the particular row and colums and the value which is entered,
public void setValueAt(Object aValue, int rowIndex, int columnIndex)
Object[] row = (Object[]) data.get(rowIndex);
row[columnIndex] = aValue;
super.fireTableCellUpdated(rowIndex, columnIndex);
but it is not executing the super.fireTableCellUpdated() function.
i will be thankful if you provide me with the solution for the above problem or provide me any other way.
Thank's in Advance.

Use the DefaultTableModel, then you don't have to write custom code for the setValueAt() method.
If you need further help then you need to create a [Short, Self Contained, Compilable and Executable, Example Program (SSCCE)|http://homepage1.nifty.com/algafield/sscce.html], that demonstrates the incorrect behaviour.
Don't forget to use the Code Formatting Tags so the posted code retains its original formatting. That is done by selecting the code and then clicking on the "Code" button above the question input area.

Cascading LOVs (APEX 4.1) problem, using in report does not set values

Hi,
i am using APEX 4.1.0.00.32 and i have a simple report as
SQL:*
SELECT * from region
WHERE region like '%'||P3_REGION||'%'
and country like '%'||P3_COUNTRY||'%'
and city like '%'||P3_CITY||'%'
Items:*
P3_REGION:
select distinct region as d, region as r from region
Display Null value: YES
Null display value: - select -
Null return value: +0+
P3_COUNTRY:
select distinct country as d, country as r from region where region = :P3_REGION
Display Null value: YES
Null display value: - select -
Null return value: +0+
Cascading LOV Parent Item(s): P3_REGION
P3_CITY:
+select distinct city as d, city as r from region where country = :P3_COUNTRY
Display Null value: YES
Null display value: - select -
Null return value: +0+
Cascading LOV Parent Item(s): P3_COUNTRY
The LOVs work fine and the correct values are displayed if cascading through them
So in the last step i want to filter the report with the values that were selected in the lovs. And this i get not working.
I tried to add a button with SUBMIT of the page. After choosing values in all LOVs and clicking the SUBMIT button the page submits, alle LOVs are cleared (with value - select -) and the report shows all rows.
I tried to change the button to "redirect to Page 3" and setting the values P3_REGION, P3_COUNTRY, P3_CITY to &P3_REGION., &P3_COUNTRY., &P3_CITY. but without success.
I tried to use the setting "Page Action when Value Changed" to "Submit" and/or "Redirect and set value" for all Item LOVs and/or only the last item LOV, but then the cascade of the LOVs does not work properly and the report does not change too.
I am confused as i don´t know what i can do until now. I think this should be an easy requirement to limit/filter the report with values in the LOVs.
Furthermore it should be possible to choose only the region LOV and then limit the report with that region (without choosing country and city)
Thanks in advance!

Hi Dan,
thank you for your answer. I have the solution now from Kleber_M, this works.
Dan McGhan wrote:
1. Use bind variables in my query. It would look something like:
SELECT *
FROM region
WHERE region LIKE '%'|| :P3_REGION ||'%'
AND country LIKE '%'|| :P3_COUNTRY ||'%'
AND city LIKE '%'|| :P3_CITY ||'%'
This was only a mistake when writing the post, i forgot the colon. I use bind variables of course.
2. Make sure you have a comma separated list of item names that the report depends on beneath the SQL Query where it says Page Items to Submit. This will make sure that the value of those items on the page are bound into session state prior to the query executing.I tried this, too, but without success...
3. Use Dynamic Actions to perform the refresh action when any of the three items changes. This would be both more performant and a better experience for the end user than a full page refresh.How can i do this. This sounds good, because when refreshing the page often some items oder actions are done that i don´t want to.
Regards,
Matze

CISCO-UNIFIED-COMPUTING-TC-MIB won't compile

Hello,
I'm trying to monitor my UCS C260 using SNMP traps sent to HP SIM. In order do import the Cisco MIBs into SIM, you compile a .cfg file. One of the MIBs, CISCO-UNIFIED-COMPUTING-TC-MIB, will not compile. When running the mcompile command, I get the following error message:
C:\Program Files\HP\Systems Insight Manager\mibs>mcompile CISCO-UNIFIED-COMPUTING-tc-MIB.mib
HP Systems Insight Manager Mib Compiler, Version 5.0.2.1
Copyright (c) 2003-2006 Hewlett Packard Corporation
Compiling CISCO-UNIFIED-COMPUTING-tc-MIB.mib
Line: 128: Error defining object: expected a label, found reserved symbol {
Mib compilation failed.
All of the other MIBs compile just fine and I don't see anything wrong with the MIB I downloaded from Cisco.
Any idea what might be going on here?
Attached is the MIB as well.

Chaps, i had the same issue, spoke with the chaps from Castle Rock and they confirmed this was due to bad coding within the MIB file.
I have succesfully compiled the version kindly amended by castlerock, they were quick to resolve this, their explanation as to the problem as below:
The problems with the MIB were that they are trying to enumerate the values with gauge and counter types. Only INTEGER/Integer32 types may have enumerated values (RFC2578, 7.1.1). There isn't a 64 bit integer type so they can't enumerate the Counter64 bit values. There were also problems trying to enumerate a textual-convention type (snmpAdminString) which is wrong in two ways - you can't enumerate a string value, and you can't nest a textual convention macro as a syntax in another (RFC1903, 3.5).
Please find the version i used attached.
Please feed back to the forum if this resolves the issue for your type of platform.....
Cheers
Barry

Dynamic action with set value on date field

Hi,
I'm using APEX 4.02
I'm trying to calculate the age based on the date of birth dynamically on a form. I'm trying to do this with a (advanced)dynamic action with set value.
I'm able to get this kind of action working based on a number field etc, but NEVER on a date field.
I've read all posts on this subject but so far no solution. Even if I try to simply copy the value over to another date field or typecast it to a string ( to_char function ) it does not work. So for me the problem seems to be in the source field being a date field.
I've tried using the source value as is in a select statement :
select :P33_GEBOORTEDATUM from dual;
and also type casted based on the date format :
select TO_DATE(:P33_GEBOORTEDATUM,'DD-MON-YYYY') from dual
but still no luck.
On the same form I don't have any issues as long as the calculation is based on number fields, but as soon as I start using dates all goes wrong.
Any suggestions would be greatly appreciated. If you need any extra info just let me know.
Cheers
Bas
b.t.w My application default date format is DD-MON-YYYY, maybe this has something to do with the issue .... ?
Edited by: user3338841 on 3-apr-2011 7:33

Hi,
Create a dynamic action named "set age" with following values.
Event: Change
Selection Type: Item(s)
Item(s): P1_DATE_OF_BIRTH
Action: Set value
Fire on page load: TRUE
Set Type: PL/SQL Expression
PL/SQL Expression: ROUND( (SYSDATE - :P1_DATE_OF_BIRTH)/365.24,0)
Page items to submit: P1_DATE_OF_BIRTH
Selection Type: Item(s)
Item(s): P1_AGE
Regards,
Kartik Patel
http://patelkartik.blogspot.com/
http://apex.oracle.com/pls/apex/f?p=9904351712:1

SQL Query (updateable report) Region - Conditionally Hide and Set Values

SQL Query (updateable report) Region - Conditionally Hide and Set Values
Outline of requirement :-
Master / Detail page with Detail updated on same page using SQL Query (updateable report).
The detail region has the following source
SELECT item_id,
       contract_id,
       CASE WHEN hardware_id IS NOT NULL THEN
               'HA'
            WHEN backup_dev_id IS NOT NULL THEN
               'BD'
            WHEN hardware_os_id IS NOT NULL THEN
               'HS'
       END item_type,
       hardware_id,
       backup_dev_id,
       hardware_os_id
FROM   "#OWNER#".support_items
WHERE contract_id = :P26_CONTRACT_IDThe table support_items implements arced relationships and has the following columns
CREATE TABLE SUPPORT_ITEMS
ITEM_ID         NUMBER                        NOT NULL,
CONTRACT_ID     NUMBER                        NOT NULL,
HARDWARE_ID     NUMBER,
BACKUP_DEV_ID   NUMBER,
HARDWARE_OS_ID NUMBER
)A check type constaint on support_items ensures that only one of the fk's is present.
      (    hardware_id    IS NOT NULL
       AND backup_dev_id IS NULL
       AND hardware_os_id IS NULL
OR    (    hardware_id    IS NULL
       AND backup_dev_id IS NOT NULL
       AND hardware_os_id IS NULL
OR    (    hardware_id    IS NULL
       AND backup_dev_id IS NULL
       AND hardware_os_id IS NOT NULL
      )    Hardware_Id is a FK to Hardware_Assets
Backup_dev_id is a FK to Backup_Devices
Hardware_os_id is a FK to Hardware_op_systems
The Tabular Form Element based on item_type column of SQL query is Displayed As Select List (based on LOV) referencing a named list of values which have the following properties
Display Value     Return Value
Hardware Asset    HA
Backup Device     BD
Computer System   HSThe Tabular Form Elements for the report attributes for hardware_id, backup_dev_id and hardware_os_id are all Displayed As Select List (Based on LOV).
What I want to do is only display the Select List for the FK depending on the value of the Select List on Item Type, e.g.
Item_Type is 'HA' then display Select List for hardware_id, do not display and set to NULL the Select Lists for backup_dev_id and hardware_os_id.
Item_Type is 'BB' then display Select List for backup_dev_id, do not display and set to NULL the Select Lists for hardware_id and hardware_os_id.
Item_Type is 'HS' then display Select List for hardware_os_id, do not display and set to NULL the Select Lists backup_dev_id and hardware_id.
There are properties on elements to conditionally display it but how do we reference the values of the SQL query Updateable region? they are not given a page item name?
Also on the Tabular For Elements there is an Edit tick against a report item - however when you go to the Column Attributes there is not a property with which you can control the Edit setting.
What's the best way of implementing this requirement in APEX 3.1?
Thanks.

>
Welcome to the forum: please read the FAQ and forum sticky threads (if you haven't done so already), and update your profile with a real handle instead of "user13515136".
When you have a problem you'll get a faster, more effective response by including as much relevant information as possible upfront. This should include:
<li>Full APEX version
<li>Full DB/version/edition/host OS
<li>Web server architecture (EPG, OHS or APEX listener/host OS)
<li>Browser(s) and version(s) used
<li>Theme
<li>Template(s)
<li>Region/item type(s) (making particular distinction as to whether a "report" is a standard report, an interactive report, or in fact an "updateable report" (i.e. a tabular form)
With APEX we're also fortunate to have a great resource in apex.oracle.com where we can reproduce and share problems. Reproducing things there is the best way to troubleshoot most issues, especially those relating to layout and visual formatting. If you expect a detailed answer then it's appropriate for you to take on a significant part of the effort by getting as far as possible with an example of the problem on apex.oracle.com before asking for assistance with specific issues, which we can then see at first hand.
I have a multi-row region that displays values and allows entries in a number of fields.Provide exact details of how this has been implemented. (An example on apex.oracle.com is always a good way to do this.)
I should like the fields to be conditional in that they do not permit entry, but still display, if certain conditions apply (e.g. older rows greyed out). Can this be done? Almost anything can be done, often in multiple ways. Which are appropriate may be dependent on a particular implementation, the skills available to implement it, and the effort you're willing to expend on it. Hence it's necessary to provide full details of what you've done so far...

Problems setting up username & password for SQL

Due to the outstanding advice I recieved from this excellent forum, I have managed to overcome my first problem with declaring a new Class.
This leads me to request help with my next biggest problem:
Setting up a user GUI that takes a "username" & "password" that will be used to access a password protected database.
I am a simple bloke, with simple thought processes, so please, go easy on me...
import java.awt.*;
import java.awt.event.*;
import javax.swing.*;
import java.sql.*;
public class DBQuery1 {
     String username = "" , password = "";
     public static void main(String[] arguments) {
          PassDB UPass = new PassDB();
          String data = "jdbc:odbc:JavaTestDataBase";
          try {
               Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
               Connection conn = DriverManager.getConnection(data, "" + username, "" + password);
               Statement st = conn.createStatement();
               ResultSet rec = st.executeQuery(
                    "SELECT Title, ContactID, First, Last, Dear FROM Contacts "
                    + "WHERE (Title='Mr') ORDER BY ContactID");
          /*     ResultSet rec2 = st.executeQuery(
                    "SELECT Subject, ContactID FROM Calls "
                    + "WHERE (Subject Is Not Null) ORDER BY ContactID");
          System.out.println("\nFirst Name\tSurname\t\tNick Name\t\tSubject\n");
          while(rec.next()) {
               System.out.println(rec.getString(3) + "\t\t" + rec.getString(4) + "\t\t" + rec.getString(5) /* + rec2.getString(1) */ );
          st.close();
          catch (SQLException s) {
               System.out.println("SQL Error: " + s.toString() + " " + s.getErrorCode() + " " + s.getSQLState());
          catch (Exception e) {
               System.out.println("Error: " + e.toString() + e.getMessage());
class PassDB extends javax.swing.JFrame implements ActionListener {
     String username = "", password = "";
     JTextField uname = new JTextField(10);
     JTextField pword = new JTextField(10);
     // JPasswordField pword = new JTextField(10);
     PassDB() {
          super("duBe's database logon");
          setSize(220, 160);
          setDefaultCloseOperation(EXIT_ON_CLOSE);
          JPanel pane = new JPanel();
          JLabel unameLabel = new JLabel ("Username: ");
          JLabel pwordLabel = new JLabel ("Password: ");
          JButton submit = new JButton("OK");
          submit.addActionListener(this);
          pane.add(unameLabel);
          pane.add(uname);
          pane.add(pwordLabel);
          pane.add(pword);
          pane.add(submit);
          setContentPane(pane);
          setVisible(true);
     public void actionPerformed(ActionEvent evt) {
          PassDB clicked = (PassDB)evt.getSource();
          username = uname.getText();
          password = pword.getText();
This code generates two errors, stating:
C:\Java_progs>javac DBQuery1.java
DBQuery1.java:14: non-static variable username cannot be referenced from a static context
Connection conn = DriverManager.getConnection(data, "" +
username, "" + password);
^
DBQuery1.java:14: non-static variable password cannot be referenced from a static context
Connection conn = DriverManager.getConnection(data, "" +
username, "" + password);
                ^
2 errors*****************************
The code works when I remove the reference to the variables "username" & "password" in Connection "conn" call & replace them with the actual username & password, but this is not exactly what I was after. I was hoping to make the program responsive to each individual user, not set in code.
I also would like to make the program pause after the call in "main" to "PassDB" to wait for "PassDB" to exit before continuing.
I would also like to make "PassDB" destroy itself after the "OK" button is pressed & the "username" & "password" set.
If that isn't enough for you, I would really like the program to search 2 different database tables, return their values & compare them to be sure that they are the same.
When I try & search 2 different tables, as in:
ResultSet rec = st.executeQuery(
                    "SELECT Title, ContactID, First, Last, Dear FROM Contacts "
                    + "WHERE (Title='Mr') ORDER BY ContactID");
               ResultSet rec2 = st.executeQuery(
                    "SELECT Subject, ContactID FROM Calls "
                    + "WHERE (Subject Is Not Null) ORDER BY ContactID")javac tells me that "ResultSet" is set to null 0
As always, I am extremely appreciative of any assistance you are able to offer.
Kind regards
duBedat
[email protected]

This is where I'm at now:
import java.awt.*;
import java.awt.event.*;
import javax.swing.*;
import java.sql.*;
public class DBQuery {
     static String username = "" ;
     static String password = "" ;
     public static void main(String[] arguments) {
     PassDB UPass = new PassDB();
     String data = "jdbc:odbc:JavaTestDataBase";
     try {
          Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
          Connection conn = DriverManager.getConnection(data, "" + DBQuery.username, "" + DBQuery.password);
          Statement st = conn.createStatement();
          ResultSet rec = st.executeQuery(
          "SELECT Title, ContactID, First, Last, Dear FROM Contacts "
          + "WHERE (Title='Mr') ORDER BY ContactID");
          /*     ResultSet rec2 = st.executeQuery(
               "SELECT Subject, ContactID FROM Calls "
               + "WHERE (Subject Is Not Null) ORDER BY ContactID");
          System.out.println("\nFirst Name\tSurname\t\tNick Name\t\tSubject\n");
          while(rec.next()) {
               System.out.println(rec.getString(3) + "\t\t" + rec.getString(4) + "\t\t" + rec.getString(5) /* + rec2.getString(1) */ );
          st.close();
     catch (SQLException s) {
          System.out.println("SQL Error: " + s.toString() + " " + s.getErrorCode() + " " + s.getSQLState());
     catch (Exception e) {
          System.out.println("Error: " + e.toString() + e.getMessage());
class PassDB extends javax.swing.JFrame implements ActionListener {
     static boolean getOut = false;
     JTextField uname = new JTextField(10);
     JTextField pword = new JTextField(10);
     // JPasswordField pword = new JTextField(10);
     public PassDB() {
          super("duBe's database logon");
          setSize(220, 160);
          setDefaultCloseOperation(EXIT_ON_CLOSE);
          JPanel pane = new JPanel();
          JLabel unameLabel = new JLabel ("Username: ");
          JLabel pwordLabel = new JLabel ("Password: ");
          JButton submit = new JButton("OK");
          submit.addActionListener(this);
          pane.add(unameLabel);
          pane.add(uname);
          pane.add(pwordLabel);
          pane.add(pword);
          pane.add(submit);
          setContentPane(pane);
          while(getOut == false)
               setVisible(true);
     public void actionPerformed(ActionEvent evt) {
          PassDB clicked = (PassDB)evt.getSource();
          DBQuery.username = uname.getText();
          DBQuery.password = pword.getText();
          getOut = true;
}          Any advice is greatly appreciated
duBe

Problems setting up an NFS server

Hi everybody,
I just completed my first arch install. :-)
I have a desktop and a laptop, and I installed Arch on the desktop (the laptop runs Ubuntu 9.10). I had a few difficulties here and there, but I now have the system up and running, and I'm very happy.
I have a problem setting up an NFS server. With Ubuntu everything was working, so I'm assuming that the Ubuntu machine (client) is set-up correctly. I'm trying to troubleshoot the arch box (server) now.
I followed this wiki article: http://wiki.archlinux.org/index.php/Nfs
Now, I have these problems:
- when I start the daemons, I get:
[root@myhost ~]# /etc/rc.d/rpcbind start
:: Starting rpcbind [FAIL]
[root@myhost ~]# /etc/rc.d/nfs-common start
:: Starting rpc.statd daemon [FAIL]
[root@myhost ~]# /etc/rc.d/nfs-server start
:: Mounting nfsd filesystem [DONE]
:: Exporting all directories [BUSY] exportfs: /etc/exports [3]: Neither 'subtree_check' or 'no_subtree_check' specified for export "192.168.1.1/24:/home".
Assuming default behaviour ('no_subtree_check').
NOTE: this default has changed since nfs-utils version 1.0.x
[DONE]
:: Starting rpc.nfsd daemon [FAIL]
- If I mount the share on the client with "sudo mount 192.168.1.20:/home /media/desktop", IT IS mounted but I can't browse it because I have no privileges to access the home directory for the user.
my /etc/exports looks like this:
# /etc/exports: the access control list for filesystems which may be exported
# to NFS clients. See exports(5).
/home 192.168.1.1/24(rw,sync,all_squash,anonuid=99,anongid=99))
/etc/conf.d/nfs-common.conf:
# Parameters to be passed to nfs-common (nfs clients & server) init script.
# If you do not set values for the NEED_ options, they will be attempted
# autodetected; this should be sufficient for most people. Valid alternatives
# for the NEED_ options are "yes" and "no".
# Do you want to start the statd daemon? It is not needed for NFSv4.
NEED_STATD=
# Options to pass to rpc.statd.
# See rpc.statd(8) for more details.
# N.B. statd normally runs on both client and server, and run-time
# options should be specified accordingly. Specifically, the Arch
# NFS init scripts require the --no-notify flag on the server,
# but not on the client e.g.
# STATD_OPTS="--no-notify -p 32765 -o 32766" -> server
# STATD_OPTS="-p 32765 -o 32766" -> client
STATD_OPTS="--no-notify"
# Options to pass to sm-notify
# e.g. SMNOTIFY_OPTS="-p 32764"
SMNOTIFY_OPTS=""
# Do you want to start the idmapd daemon? It is only needed for NFSv4.
NEED_IDMAPD=
# Options to pass to rpc.idmapd.
# See rpc.idmapd(8) for more details.
IDMAPD_OPTS=
# Do you want to start the gssd daemon? It is required for Kerberos mounts.
NEED_GSSD=
# Options to pass to rpc.gssd.
# See rpc.gssd(8) for more details.
GSSD_OPTS=
# Where to mount rpc_pipefs filesystem; the default is "/var/lib/nfs/rpc_pipefs".
PIPEFS_MOUNTPOINT=
# Options used to mount rpc_pipefs filesystem; the default is "defaults".
PIPEFS_MOUNTOPTS=
/etc/hosts.allow:
nfsd: 192.168.1.0/255.255.255.0
rpcbind: 192.168.1.0/255.255.255.0
mountd: 192.168.1.0/255.255.255.0
Any help would be very appreciated!

Thanks, I finally got it working.
I realized that even though both machines had the same group, my Ubuntu machine (client) group has GID 1000, while the Arch one has GID 1001. I created a group that has GID 1001 on the client, and now everything is working.
I'm wondering why my Arch username and group both have 1001 rather than 1000 (which I suppose would be the default number for the first user created).
Anyway, thanks again for your inputs.

Problems setting up JDBC

I recently downloaded mysql Connector for my project.
However, I have problems setting it up.
When I run my program, It gives me a class not defined error.
System.out.println("Registering Driver...");
Class.forName("com.mysql.jdbc.Driver").newInstance();
System.out.println("Connected to database");
System.out.println("Creating Connection");
connection= DriverManager.getConnection("jdbc:mysql://localhost:8080/neuis");
System.out.println("Connection created");
catch(Exception ex)
System.out.println("Error in loading jdbc Driver: "+ex);
ex.printStackTrace();
I have put the jar file of the JDBC Bridge in a folder
C:\Drivers\Sql Connector
I have also added the absolute path of the jar to the system classpath
The value put in is:
C:\Drivers\Sql Connector\mysql-connector-java-3.1.10-bin.jar.
I am not sure what the problem is because I was told by the API that this was all I needed to do. Are there any other files I need to include with the jar file? Also, Is there a specific folder I must put it in?
Thank you in advance.

Hi,
Take a look at the below link
http://www.cs.nott.ac.uk/TSG/manuals/databases/mysql/jdbc.html
may help you to setting up the jdbc with mysql
regards
MJ

Problems setting up MPLS

A Chairde,
Am having problems setting up MPLS between a AS5350 and 7609 , I have used commands stated in this link, enable MPLS incrementally on a network.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/switch_c/xcprt4/xcdtagc.pdf
The commands below are added to each router, and some troubleshooting.
7609
ip cef distributed
interface Loopback0
ip address 192.168.254.1 255.255.255.255
tag-switching advertise-tags
interface GigabitEthernet3/12
ip address 192.168.230.162 255.255.255.248
mpls label protocol tdp
tag-switching ip
AS5350
ip cef
mpls label protocol tdp
tag-switching advertise-tags
interface Loopback0
ip address 192.168.254.2 255.255.255.255
interface FastEthernet0/0
ip address 192.168.230.161 255.255.255.248
duplex auto
speed auto
mpls ip
h323-gateway voip interface
h323-gateway voip id cnibhco111 ipaddr 192.168.230.129 1719
h323-gateway voip h323-id cnibhco112
h323-gateway voip tech-prefix 71401
h323-gateway voip tech-prefix 0030
h323-gateway voip bind srcaddr 192.168.230.161
ip rsvp bandwidth 64 64
cnibhco112#sh tag-switching tdp neighbor
Peer TDP Ident: 192.168.254.1:0; Local TDP Ident 192.168.230.161:0
TCP connection: 192.168.254.1.49842 - 192.168.230.161.711
State: Oper; PIEs sent/rcvd: 18/23; Downstream
Up time: 00:12:54
TDP discovery sources:
FastEthernet0/0, Src IP addr: 192.168.230.162
Addresses bound to peer TDP Ident:
192.168.100.17 192.168.100.25 159.107.212.49 172.16.8.81
192.168.230.130 192.168.230.77 192.168.230.81 192.168.254.1
192.168.210.6 192.168.127.6 192.168.210.106 192.168.127.66
192.168.127.138 192.168.210.146 192.168.210.142 192.168.210.122
192.168.210.17 192.168.230.140 192.168.230.26 192.168.230.74
192.168.230.10 192.168.230.14 192.168.127.130 192.168.127.142
192.168.230.6 192.168.230.70 192.168.230.34 192.168.210.178
192.168.200.25 192.168.210.126 192.168.232.1 192.168.231.1
192.168.200.17 192.168.210.102 190.168.200.245 190.168.200.225
190.168.201.241 192.168.230.98 192.168.210.14 190.168.201.201
190.168.201.209 192.168.210.162 192.168.210.210 190.168.201.205
192.168.230.38 190.168.200.249 190.168.200.217 190.168.200.253
192.168.230.162
cnibhco112#
cnibhco112#sh tag-switching forwarding-table 192.168.254.1 detail
Local Outgoing Prefix Bytes tag Outgoing Next Hop
tag tag or VC or Tunnel Id switched interface
cnibhco112#traceroute 192.168.254.1
Type escape sequence to abort.
Tracing the route to 192.168.254.1
1 192.168.230.162 0 msec 0 msec *
cnibhco112#traceroute 192.168.230.162
Type escape sequence to abort.
Tracing the route to 192.168.230.162
1 192.168.230.162 0 msec 0 msec *
cnibhco112#

Ro,
Thanks for the respone, have been playin, with MPLS for last few hours.
The routing between the loopbacks is now working, can PING 7609 Loopback from AS5350 ,and vice versa. (used static routes).
Having problem with TDP / LDP on routers,
mpls label protocol ldp / tdp command works correctly on both routers, but the
tag-switching tdp router-id Loopback0 force
command works on the 7609, but when I add it onto the AS5350 , the command "mpls ldp router-id Loopback0 force" appears on the startup script.
The opposite is true for the 7609 , you add MPLS LDP command, and TAG-SWITCHING command appears instead.
Any Ideas, as different configs of this leave me with forwarding table with both tags added, but not been able to ping the loopbacks !!!
When I can ping bot loopbacks, the OUTGOING TAG , disapears.....
Problem is LOOPBACK Commands on bot routers default to LDP (AS5350) , or TDP (7609). Any Ideas ...
mpls label protocol tdp
tag-switching tdp router-id Loopback0 force
mpls label protocol tdp
mpls ldp router-id Loopback0 force
cnibhco100#sh tag-switching forwarding-table 192.168.254.2 detail
Local Outgoing Prefix Bytes tag Outgoing Next Ho
tag tag or VC or Tunnel Id switched interface
18 17 192.168.254.0/24 0 Gi3/12 192.168.2
MAC/Encaps=14/18, MRU=1500, Tag Stack{17}
00097CA3293000127FCDBA808847 00011000
No output feature configured
Per-packet load-sharing
cnibhco100#traceroute 192.168.254.2
Type escape sequence to abort.
Tracing the route to 192.168.254.2
1 192.168.230.161 [MPLS: Label 17 Exp 0] 0 msec 0 msec 0 msec
2 192.168.230.162 0 msec 0 msec 0 msec
But no PINGING 192.168.254.2
cnibhco112#sh tag-switching forwarding-table 192.168.254.1 detail
Local Outgoing Prefix Bytes tag Outgoing Next Hop
tag tag or VC or Tunnel Id switched interface
17 18 192.168.254.0/24 1915668 Fa0/0 192.168.230.162
MAC/Encaps=14/18, MRU=1500, Tag Stack{18}
00127FCDBA8000097CA329308847 00012000
No output feature configured
Per-packet load-sharing
cnibhco100#sh tag-switching forwarding-table 192.168.254.2 detail
Local Outgoing Prefix Bytes tag Outgoing Next Ho
tag tag or VC or Tunnel Id switched interface
18 17 192.168.254.0/24 752551 Gi3/12 192.168.2
MAC/Encaps=14/18, MRU=1500, Tag Stack{17}
00097CA3293000127FCDBA808847 00011000
No output feature configured
Per-packet load-sharing
WHEN BOTH LOCAL AND OUTGOING TAG, CANNOT PING EITHER WAY !!!
HAVE LABEL PROTOCOL AND LOOPBACK FORCE on AS5350
HAVE LABEL PROTOCOL ON 7609
WHEN ADD LOOPBACK FORCE on 7609 , CAN PING BOTH LOOPBACKS,
BUT OUTGOING TAG DISAPEARS
cnibhco112#PING 192.168.254.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.254.2, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
cnibhco112#sh tag-switching forwarding-table 192.168.254.1 detail
Local Outgoing Prefix Bytes tag Outgoing Next Hop
tag tag or VC or Tunnel Id switched interface
17 Untagged 192.168.254.0/24 598678 Fa0/0 192.168.230.162
MAC/Encaps=0/0, MRU=1504, Tag Stack{}
No output feature configured
Per-packet load-sharing
cnibhco112#
mpls label protocol tdp
tag-switching tdp router-id Loopback0 force

Mapping in BPM - set value of collection item

Hello,
is it possible to set value to exact item of collection in mapping step in netweaver BPM?
I need something like set(<collection_variable>,<item_index>,<item_value>) - so exact opposite of GET generic function, which gets specific item from collection.
Is it possible in NW BPM?

You dont have to apologize. I didnt meant that as offend.
I appreciate the possibility to discuss that topic with somebody, because discussion itself sometimes shows other perspective to the problem, which can lead to solution
Of course I wrote EJB function to solve that - but I cant believe that it isnt standard solution to that pretty common use case.
I think, that problem lays in very limited implementation of XPath into Netweaver BPM. I will bet my left hand, that in some future SP of BPM will SAP introduce something like this:
myCollection[1]/notificationId = notificationId
which is standard XPath way to do that

ALC-DSC-000-000 on a "Set Value" activity

I have in my form some hidden fields I want to set in the process, before user assignement. For this, I use the Set Value activity.
But when I tried to set a field of my form with a value, I got this error:
Internal error.: ALC-DSC-000-000: com.adobe.idp.dsc.DSCRuntimeException: Internal error.
     at com.adobe.idp.dsc.util.CoercionUtil.toDOMDocument(CoercionUtil.java:683)
     at com.adobe.idp.dsc.util.CoercionUtil.toDOMDocument(CoercionUtil.java:688)
     at com.adobe.idp.dsc.util.CoercionUtil.toType(CoercionUtil.java:974)
     at com.adobe.workflow.datatype.CoercionUtil.toType(CoercionUtil.java:168)
     at com.adobe.workflow.datatype.runtime.impl.pojo.POJODataTypeNode.getBoundValue(POJODataTypeNode.java:71)
     at com.adobe.workflow.datatype.runtime.impl.xml.XMLDataTypeNode.replaceContent(XMLDataTypeNode.java:267)
     at com.adobe.workflow.dom.InstanceElement.replaceContent(InstanceElement.java:241)
     at com.adobe.workflow.pat.service.PATExecutionContextImpl.setProcessDataValue(PATExecutionContextImpl.java:806)
     at com.adobe.workflow.pat.service.PATExecutionContextImpl.setProcessDataWithExpression(PATExecutionContextImpl.java:374)
     at com.adobe.idp.workflow.dsc.service.SetValueService.execute(SetValueService.java:54)
     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:79)
     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43)
     at java.lang.reflect.Method.invoke(Method.java:618)
     at com.adobe.idp.dsc.component.impl.DefaultPOJOInvokerImpl.invoke(DefaultPOJOInvokerImpl.java:118)
     at com.adobe.idp.workflow.dsc.invoker.WorkflowDSCInvoker.invoke(WorkflowDSCInvoker.java:153)
     at com.adobe.idp.dsc.interceptor.impl.InvocationInterceptor.intercept(InvocationInterceptor.java:140)
     at com.adobe.idp.dsc.interceptor.impl.RequestInterceptorChainImpl.proceed(RequestInterceptorChainImpl.java:60)
     at com.adobe.idp.dsc.transaction.interceptor.TransactionInterceptor$1.doInTransaction(TransactionInterceptor.java:74)
     at com.adobe.idp.dsc.transaction.impl.ejb.adapter.EjbTransactionCMTAdapterBean.execute(EjbTransactionCMTAdapterBean.java:342)
     at com.adobe.idp.dsc.transaction.impl.ejb.adapter.EjbTransactionCMTAdapterBean.doSupports(EjbTransactionCMTAdapterBean.java:212)
     at com.adobe.idp.dsc.transaction.impl.ejb.adapter.EJSLocalStatelessEjbTransactionCMTAdapter_caf58c4f.doSupports(Unknown Source)
     at com.adobe.idp.dsc.transaction.impl.ejb.EjbTransactionProvider.execute(EjbTransactionProvider.java:104)
     at com.adobe.idp.dsc.transaction.interceptor.TransactionInterceptor.intercept(TransactionInterceptor.java:72)
     at com.adobe.idp.dsc.interceptor.impl.RequestInterceptorChainImpl.proceed(RequestInterceptorChainImpl.java:60)
     at com.adobe.idp.dsc.interceptor.impl.InvocationStrategyInterceptor.intercept(InvocationStrategyInterceptor.java:55)
     at com.adobe.idp.dsc.interceptor.impl.RequestInterceptorChainImpl.proceed(RequestInterceptorChainImpl.java:60)
     at com.adobe.idp.dsc.interceptor.impl.InvalidStateInterceptor.intercept(InvalidStateInterceptor.java:37)
     at com.adobe.idp.dsc.interceptor.impl.RequestInterceptorChainImpl.proceed(RequestInterceptorChainImpl.java:60)
     at com.adobe.idp.dsc.interceptor.impl.AuthorizationInterceptor.intercept(AuthorizationInterceptor.java:132)
     at com.adobe.idp.dsc.interceptor.impl.RequestInterceptorChainImpl.proceed(RequestInterceptorChainImpl.java:60)
     at com.adobe.idp.dsc.interceptor.impl.JMXInterceptor.intercept(JMXInterceptor.java:48)
     at com.adobe.idp.dsc.interceptor.impl.RequestInterceptorChainImpl.proceed(RequestInterceptorChainImpl.java:60)
     at com.adobe.idp.dsc.engine.impl.ServiceEngineImpl.invoke(ServiceEngineImpl.java:115)
     at com.adobe.idp.dsc.routing.Router.routeRequest(Router.java:118)
     at com.adobe.idp.dsc.provider.impl.base.AbstractMessageReceiver.routeMessage(AbstractMessageReceiver.java:91)
     at com.adobe.idp.dsc.provider.impl.vm.VMMessageDispatcher.doSend(VMMessageDispatcher.java:215)
     at com.adobe.idp.dsc.provider.impl.base.AbstractMessageDispatcher.send(AbstractMessageDispatcher.java:57)
     at com.adobe.idp.dsc.clientsdk.ServiceClient.invoke(ServiceClient.java:208)
     at com.adobe.workflow.engine.PEUtil.invokeAction(PEUtil.java:724)
     at com.adobe.workflow.engine.SynchronousBranch.handleInvokeAction(SynchronousBranch.java:465)
     at com.adobe.workflow.engine.SynchronousBranch.execute(SynchronousBranch.java:862)
     at com.adobe.workflow.engine.ProcessEngineBMTBean.continueBranchAtAction(ProcessEngineBMTBean.java:2773)
     at com.adobe.workflow.engine.ProcessEngineBMTBean.asyncInvokeProcessCommand(ProcessEngineBMTBean.java:704)
     at com.adobe.workflow.engine.EJSLocalStatelessadobe_ProcessEngineBMTEJB_7d3cbd67.asyncInvokeProcessCommand(Unknown Source)
     at com.adobe.workflow.engine.ProcessCommandControllerBean.doOnMessage(ProcessCommandControllerBean.java:156)
     at com.adobe.workflow.engine.ProcessCommandControllerBean.onMessage(ProcessCommandControllerBean.java:99)
     at com.ibm.ejs.container.MessageEndpointHandler.invokeMdbMethod(MessageEndpointHandler.java:1014)
     at com.ibm.ejs.container.MessageEndpointHandler.invoke(MessageEndpointHandler.java:747)
     at $Proxy0.onMessage(Unknown Source)
     at com.ibm.ws.sib.api.jmsra.impl.JmsJcaEndpointInvokerImpl.invokeEndpoint(JmsJcaEndpointInvokerImpl.java:201)
     at com.ibm.ws.sib.ra.inbound.impl.SibRaDispatcher.dispatch(SibRaDispatcher.java:768)
     at com.ibm.ws.sib.ra.inbound.impl.SibRaSingleProcessListener$SibRaWork.run(SibRaSingleProcessListener.java:584)
     at com.ibm.ejs.j2c.work.WorkProxy.run(WorkProxy.java:419)
     at com.ibm.ws.util.ThreadPool$Worker.run(ThreadPool.java:1473)
Caused by: ALC-DSC-119-000: com.adobe.idp.dsc.util.InvalidCoercionException: Cannot coerce object: [B@10e410e4 of type: [B to type: interface org.w3c.dom.Document
     at org.apache.xerces.parsers.DOMParser.parse(Unknown Source)
     at org.apache.xerces.jaxp.DocumentBuilderImpl.parse(Unknown Source)
     at com.adobe.idp.dsc.util.DOMUtil.parseDocumentFromString(DOMUtil.java:167)
     at com.adobe.idp.dsc.util.DOMUtil.parseDocumentFromString(DOMUtil.java:129)
     at com.adobe.idp.dsc.util.DOMUtil.parseDocumentFromStream(DOMUtil.java:235)
     at com.adobe.idp.dsc.util.CoercionUtil.toDOMDocument(CoercionUtil.java:670)
     ... 54 more
It seems to be an xml parsing problem. Maybe a mistake in the xml schema of my form? For the moment, I don't see any mistake in my schema.
Any idea?

Here is a screenshort of the part of my workflow:
In the mappings of the "Set Value" activity, I have one line with those properties:
Location: /process_data/bonusValidationForm/object/data/xdp/datasets/data/BonusValidationForm/buMan agerID
Expression: /process_data/currentUser/object/@userId
Where:
bonusValidationForm is a process variable of my workflow that point my xdp form
buManagerID is the textfield I want to set
currentUser is a process variable (type User) that was well setted by the task Find BU Manager

ADF Faces: How do I set values for input controls in an af:table

Use case: user enters master/detail information into an input form using an af:table for the desired number of detail rows.
I have an ADF Faces input form with master level input controls, and an af:table (bound to a backing bean CoreTable) for the detail data set.
The input controls are value bound to updateable view objects built from entity objects, with the appropriate view links providing master/detail iterators.
Once the user has entered the master keys (via inputTexts, and selectOneChoices), I create a row in the detail VO, thus creating a visible blank row in the af:table.
The user then completes the key for the detail row (in the af:table) by selecting a value in a selectOneChoice (in a af:column) with autoSubmit on and a valueChangeListener that sets the VO row attribute with the new value.
The user then continues to enter into the remaining inputTexts and selectOneChoices in the af:columns until all values have been entered.
I do not have autoSubmit on for any input controls in the af:columns other than the key, for performance improvement.
The user can then use a command button (which has an action method) to create another row in the af:table.
But, (in the action method) I need to set the values for the 1st detail VO row attributes, from the input controls, before creating another row.
The input controls are bound to backing bean CoreInputText and CoreSelectOneChoice objects, and they have not set their values at this point, even though I have partialSubmit on for the "New Row" command button.
I do not value bind the input controls in the af:columns to the backing bean objects, because we need to display data for all rows entered into the af:table.
Any advice on the best way to perform this operation would be very appreciated!!!!

Thanks for the reply Steve!!
Yes, I followed the techniques in Screencast#7, and it works great in my edit page.
But I am having problems with my input form.
I actually have master/detail/detail relationship for which I am creating an input form.
I created the input form as a copy of the edit form, and am making revisions as necessary.
I created new view objects for the input form (from my three entity objects), which have the "Tuning" set to retrieve "No Rows (i.e. used only for inserting new rows)"
I added an invokeAction that binds the "CreateInsert" action on the master iterator, so when the page is first displayed, the master level controls are available for data entry (as in 13.6.2 in the Developers Guide): but the first level detail controls are not rendered, and the af:table (for the second level detail) is rendered but with no rows.
Once the user enters key values for the master (a three part key), I manually create a first level detail row by executing the "CreateInsert" action binding for the first level detail iterator.
Continuing on, the user then enters a key value for the first level detail I manually create a second level detail row using it's "CreateInsert" action binding.
Now the user has a form with all master and first level detail controls completed and one empty row in the af:table for it's first entry.
The key column in the af:table has autoSubmit on, and an value change listener. That listener uses it's getNewValue() to set the key value ("locationCode" in this case) using
setLocationCode from the ViewRowImpl. Here is that value change listener:
public void locationChanged(ValueChangeEvent event) {
if (null != event.getNewValue()) {
LocObsCreateViewRowImpl locCreateRow = (LocObsCreateViewRowImpl)appMod.findViewObject("LocObsCreateView").getCurrentRow();
if (null == locCreateRow.getLocationCode()) {
locCreateRow.setLocationCode(event.getNewValue().toString());
Now comes my problem: once they have entered the values in the remaining columns, they can use a command button to create another row in the 2nd detail iterator, thus creating another visible empty row in the af:table. But the values from the first row (other than the key column) are not assigned to the row in the collection and I can't figure out how to set values in the collection's row.
I imagine I'm missing something using bindings and the Request Processing Lifecycle, and after reading this I can see how much manual work is going on.
The users have specified the need to have all information available on one page, so I've designed it so they can insert and iterate through the first level detail collection.
They have also asked to not use the mouse; they are looking for a "heads-down-data-entry" system.
Again, I really appreciate any advice you could give.
Jeffrey

Set value to system matrix (38) cell

Hello,
Thanks for your reply.
I need to set value for some UDF on a system matrix (38). Crurrently ,I use following code:
public void SetValue(string columnUniqueId, int matrixRowIndex, string value);
(I'm using the coresuite framwork)
The coresponding way in SDK would be:
oMatrix.Columns.Item("columnUniqueId").Cells.Item("matrixRowIndex").Specific.value = "value"
This works but when I have more than 10 UDF to fill together, the performance is bad. It takes nearly 3-4 seconds to load one item(row).
Is there any fast way to set the value? Or is there any other suggestion how to do it?

No, the problem is not by loading of UDFs by a existing document.
But when you create a new document and you add a new postion to the document by choosing an item. Then our AddOn copies the UDF values from the item master data into the corresponding UDFs in the postion. At this moment I have to write them manually.
The best would be when the UDFs in the Item Master Data would be autiomatically created also in the postion of documents. Because in this way they would be automatically loaded by SBO itself.
I think SBO has a mistake in its design by here.

Cisco IP SLA - RTTMON MIB - Problem setting values

Similar Messages

Maybe you are looking for