Cisco Ironport management interface IP configuration?

Hi,
For configuring the management interface IP for Cisco Ironport device, should it be on the public IP address or private IP address? Could you please confirm the IP address desing for the ironport management interface? thanks
arman

Greetings Aman,
The answer to this question depends on several factors, what you intend to do with the appliance, how you intend on allowing access to the appliance and where it sits in your network. Typically customers will utilize the management interface on their internal network thus giving it a private IP. This way the web interface, ssh and ftp access are allowed internally but not to the public.  Those services can be enabled on other interfaces as well, but the most common practice is to set up the management interface for internal access only on your private network.
Christopher C Smith
CSE
Cisco IronPort Customer Support 

Similar Messages

  • What is the cisco ironport C680 and M680 configuration backup file size?

    what is the cisco ironport C680 and M680 configuration backup file size?

    Size of the XML itself?  That is going to vary based on what you have configured, total lines of code, and # of appliances you may/may not have in cluster.
    M680, based on SMA as stand-alone, should be similar --- you are probably looking @ < 1 MB... 
    Looking @ my test environment, in which I have a nightly cron job set to grab a backup of...
    -rw-rw----  1 robert robert 161115 Sep 26 02:00 C000V-564D1A718795ACFEXXXX-YYYYBAD60A5A-20140926T020002.xml
    So, 161115 bytes = .15 MB
    -Robert

  • Cisco call manager Network Failover Configuration

    Hi all,
    I have a cisco call manager 6.0.
    The server is configured and is functioning very well.
    Only  today I realized that the server MCS has two NIC and there is the  possibility to configure a networ failover by cli interface.
    Now the question are:
    is it possible to configure this function now without problem?
    if yes what are the ordered steps to follow?
    Thanks all.

    Hi
    you can use EtherChannel, 2 phisical ports as 1 logical

  • Cisco ironport 370 to 670 Configuration Compatibility Issue

    I have currently Cisco IronPort S360 and want to Upgade with Cisco S670, upload configuration file of Cisco ironport 360 in &760 but unable to succeed.becasue of compatibility issue of OS .any one can help me regarding how to compatible .
    Regards,
    Shafiq

    Hi Shafiq,
    Please open a ticket and send both of your configuration files with the ticket. The CSE will need to verify that the network interfaces are the same or modify your xml file to allow it to be successfully uploaded to the new 670.
    Sincerely,
    Erik Kaiser
    WSA CSE
    WSA Cisco Forums Moderator

  • Help with Cisco 5508 management interface

    Hello,
    I'm trying to verify some behaviors I'm seeing with my 5508 controller setup and forgive me for missing anything obvious, I've zero experience with this hardware and clueless on the best practices. With that said... out of the box I ran through the AutoInstall process.
    I gave my service port an IP address on my subnet, 10.10.8.0/24 vlan 100 and gave the management interface the ip address 10.10.30.5/24 vlan 130
    From my host I can ping the management interace 10.10.30.5 and the interface gateway 10.10.30.1
    I cannot connect to the controller via 10.10.30.5 either through the web GUI or telnet
    I can connect to the controller via 10.10.8.200 both through the web interface and telnet
    while connected to the service port, I can ping the management port IP but I cannot ping the 10.10.30.1 gateway.
    We have attached two test 3502I AP's and they found the controller and pulled correct ip addresses, clients can authenticate and access network resources as well as the Internet so for the most part, things are working but it concerns me that the management interface can't ping its own gateway.
    Keep in mind, I did no other configurations besides what got configured in the AutoInstall process. What should I look at to resolve?
    Thanks!
    Mike

    The service port is for out of band management and should not be connected to the network.  If connected tot he network, it should not have connectivity to the management interface of the wlc. 
    You can create an ACL to block the service port ip to the managment vlan if you want.  I normally do not connect the service port to the network.

  • Cisco UCS Managment interface

    Hi Dear
    Which is the function of the management interface of a Cisco UCS server? Only monitoring ?
    Best Regards

    Hi,
    The management interface present in the Cisco UCS C-Series is a out-of-band interface that provides to you access to Cisco Integrated Management Controller (CIMC) where you can perform all management/monitoring tasks related the hardware set.
    You can find more information about the CIMC in this link:
    http://www.cisco.com/c/en/us/support/servers-unified-computing/ucs-c-series-integrated-management-controller/tsd-products-support-series-home.html
    Regards,
    Richard

  • 5508 WLC HA pair - change management interface settings

    Hi,
    We have a pair of 5508 WLC's in a HA configuration that is working well at the moment, however I have noticed that the management interface is configured as untagged. I would like to change this to tagged and change the attached switch to trunk for these devices but if I try and edit the management interface through the GUI the VLAN and IP address section is greyed out and cannot be changed. While I could attempt it through the CLI and am comfortable doing that, the fact that it cannot be changed through the GUI implies that this should not be changed and so I am after further information. I don't have any lab equipment other than the HA pair in production so I cannot try changing it through the CLI at the moment. 
    The WLC's are in LAG mode if that makes any difference. I realise there may be downtime required for making this change but I am trying to work out the steps to get this done without having to drastically reconfigure things. 
    Any assistance would be appreciated. 

    Introduction of New Interfaces for HA Interaction
    Redundancy Management Interface
    The IP address on this interface should be configured in the same subnet as the management interface. This interface will check the health of the Active WLC via network infrastructure once the Active WLC does not respond to Keepalive messages on the Redundant Port. This provides an additional health check of the network and Active WLC, and confirms if switchover should or should not be executed. Also, the Standby WLC uses this interface in order to source ICMP ping packets to check gateway reachability. This interface is also used in order to send notifications from the Active WLC to the Standby WLC in the event of Box failure or Manual Reset. The Standby WLC will use this interface in order to communicate to Syslog, the NTP server, and the TFTP server for any configuration upload.
    Redundancy Port
    This interface has a very important role in the new HA architecture. Bulk configuration during boot up and incremental configuration are synced from the Active WLC to the Standby WLC using the Redundant Port. WLCs in a HA setup will use this port to perform HA role negotiation. The Redundancy Port is also used in order to check peer reachability sending UDP keep-alive messages every 100 msec (default timer) from the Standby WLC to the Active WLC. Also, in the event of a box failure, the Active WLC will send notification to the Standby WLC via the Redundant Port. If the NTP server is not configured, a manual time sync is performed from the Active WLC to the Standby WLC on the Redundant Port. This port in case of standalone controller and redundancy VLAN in case of WISM-2 will be assigned an auto generated IP Address where last 2 octets are picked from the last 2 octets of Redundancy Management Interface (the first 2 octets are always 169.254).

  • Cisco IronPort AsyncOS 6.7.6-068 for Management GA Notification

    Cisco is pleased to announce the General Availability (GA) of a new major release of AsyncOS 6.7.6-068 for
    Management to all customers. This release applies to all our Security Management Appliances (M-Series).
    AsyncOS 6.7.6-068 for Management enables Centralized Tracking and Reporting for the new features introduced in AsyncOS 7.0 for Email.
    New Features and Enhancements in AsyncOS 6.7.6-068 for Management
    New Feature: Centralized support for the reporting and tracking changes in the AsyncOS for Email release 7.0:
    RSA Data Loss Prevention
    Marketing Message Detection
    New Feature: Reporting by ESA Groups
    Enhanced: Domain-Based Executive Summary Report now configurable by:
    Domain of Email Server
    Domain of Email Address
    Fixes in AsyncOS 6.7.6-068 for Management
    Fixed: MemoryError after losing Housekeeper thread [Defect ID: 52048]
    Fixed: The Show Details link results in a timeout [Defect ID: 51558]
    Fixed: Safelist/Blocklist should be exportable via CLI [Defect ID: 43360]
    Fixed: LDAP Query strips spaces [Defect ID: 46099]
    Fixed: Tracking database time does not update after system timezone is changed [Defect ID: 49407]
    Fixed: Application error when accessing Online Help from the End User Spam Quarantine page [Defect ID: 52395]
    This release has gone through our beta program, internal soak tests and is also running in production at our FCS customers.
    Please upgrade at your convenience and let us know how you like this new release!
    Cheers,
    Jakob

    Hi,
    We identified an issue in AsyncOS 6.7.6-068 for Management that under certain circumstances can cause loss of historical reporting data when reporting groups are configured. To ensure a high quality release, further testing on our side is required.
    6.7.6-068 is no longer available for upgrade to your M-Series appliances.
    If you already upgraded to 6.7.6-068 we strongly recommend to disable group based reporting to avoid being affected.
    We expect to release a new improved build of 6.7.6 shortly and apologize for any inconvenience or confusion this might have caused.
    If you are required to upgrade to 6.7.6 before a new build is available, please contact Cisco IronPort Customer Support.
    I'll let you know once the new build is available...
    Best Regards,
    Jakob

  • Configuring management interface in transparent firewall

    Hi there, 
    I know I have been asking basic questions. But I have 5520 with VPN plus license. 
    This firewall is in transparent mode now. How do I configure the management IP on this( I mean is there a dedicated management interface or what)
    Regards, 
    Yad Singh

    Hi,
    Consider ASA in transparent mode just like a Layer 2 Switch , where you would have to define an SVI or IP address for management.
    In the Case of ASA device , on ASA 8.2 and before , you can only configure one single IP address for management.
    On the ASA 8.4 and above , we have something know as Bridge groups which are configured for the management IP address.
    Refer these documents:-
    http://www.cisco.com/c/en/us/td/docs/security/asa/asa82/configuration/guide/config/fwmode.html#wp1201980
    http://www.cisco.com/c/en/us/td/docs/security/asa/asa84/configuration/guide/asa_84_cli_config/mode_fw.html#wp1367568
    http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/97853-Transparent-firewall.html
    Let me know if you have any queries.
    Thanks and Regards,
    Vibhor Amrodia

  • Ironport WSA - Management interface

    Hello,
    I have installed one Ironport WSA appliance for my customer.
    I would configure the following interface :
    -M1 : for the management
    -P1 : for the production interface
    -T1 : for L4 inspection
    I have specified a default route for M1 and P1.
    When I tryed to ping Internet or perform an update of the WSA, I watched the request exit by the M1 interface.
    It doesn't work because the management network can't exit in Internet (it's the policy of the customer).
    -It's normal that the upgrade of WSA and the ping exit by the M1 interface ?
    -If I want perform authentication in NTLM (with an AD domain) the request with the server and the client is performed with P1 or M1 ?
    -The upgrade of antivirus & sensor base use M1 or P1 ?
    -I thinked that M1 was only used for the management of the WSA (SSH and HTTPS).
    -How the WSA appliance can manage two default routes ?
    Can you give me more information about M1 and P1 and the role of each one ?
    Best Regards
    Cédric

    You can change the route that the update and upgrades use by going to System Adminstration>Upgrade and Update Settings.  Then click on the "Edit Update Settings".  You can pick the routing table/interface here.  By default its set to the managment interface.
    I'm fairly sure that the NTLM traffice from the WSA to the domain is via the managment interface.
    P1 is for the proxy traffic. Whatever way you get internet traffice to the box, it goes through P1, in and out (unless you use P2)
    M1 is for all of the other stuff: web management, ssh, updates, ldap/ntauth, etc.

  • Cisco ISE managing configuration

    Is there a built-in mechansim for revision control in Cisco ISE? If not built-in, then what is the other way? I have been trying to look for documentation online but didn't find any.
    Just to explain what I am looking for:
    A way to properly manage all the configuration changes to ISE node.  Changes are  usually identified by a number or letter code, termed the "revision  number". For example, an initial  set of files is "revision 1". When the first change is made, the  resulting set is "revision 2", and so on. Each revision is associated  with a timestamp  and the person making the change. Revisions can be compared, restored, and with some types of files, merged.
    I ask this because "show run" output in ISE CLI does not give all the configuration details. How can we maintain the history of configurations?
    PS: I rate useful posts
    Thanks,
    Kashish

    There is not a way to track which version a specific ISE configuration is on. The ADE-OS configuration, or cli configuration typically is static once the repositories, dns info...etc is all set and done. For the application database you can setup a timer where an automatic backup is generated, from there you can manage what dates a backup is good for.
    Thanks,
    Tarik Admani
    *Please rate helpful posts*

  • Configuring Cisco/IronPort plugin for Outlook with CRES

    With the discontinuation of the IronPort IEA appliances we are getting ready to move from our on-premise IEA appliances to CRES.  I have a demo key for Encryption that I am running on my C660s and I have an Outlook client configured with the Email Security Plug-In version 7.2.0.39.  Currently the Outlook Plug in is configured to point to our on premise IEA appliances for the Server URL attribute in Desktop Encryption Options and is working great.
    My question is, what do I use to connect it to CRES for desktop encryption?
    The Admin guide "Cisco IronPort Email Security Plug-in 7.2 Administrator Guide" page 4-46 just says "Server URL Enter the URL for your  Encryption server."
    Thanks

    Hi Jason,
    Thanks for your question.  The short answer is https://res.cisco.com:443 HOWEVER please note the following two points.  First, you will need a CRES account, so that you can download a token to use with the plugin, to authenticate to CRES; you cannot use the default token which you have probably been using with your IEA.  Second, using the current Outlook plug-in version 7.2 with CRES is not supported; it works, but it is not supported.  There are plans to release a supported version.

  • Cisco Provisioning Manager 2.1 bulk service area detailed configuring

    Hi folks,
    I'm really stuck and need some help desperately.
    I have bought Cisco Provisioning Manager 2.1 for 5000 handsets and I have isntalled the product ok however I am now at the stage where I need to configure the service areas. I have some 45 sites which equates to about 350 service areas.
    Service Area for each site with the following differences:
    - Odd Device, Present CLI
    - Even Device, Present CLI
    - Odd Device, Restrict CLI
    - Even Device, Restrict CLI
    Can someone please advise me a way to bulk configure these detailed attributes with some tool or a let me know of a customer northbound API application that has been written to do make this painful exercise much less painful?
    I estimate its going to take me 5 weeks full time to click through each thing and configure it..
    Please help!
    Cheers
    Beau

    You can bulk load (with batch provisioning) the Service Areas...  I did this by exporting my phones into a CSV file from Communications Manager, and then filtered it for the fields required for the SAs.  Then you just follow the instructions for batch provisioning that start here:  http://www.cisco.com/en/US/customer/docs/net_mgmt/cisco_unified_provisioning_manager/2.1/user/guide/infrstct.html#wp1051558
    I hope that helps...
    --Joe

  • Cisco ASA won't send Syslog out management interface

    I have been trying to get my ASA to send syslog out of the management interface without any luck. When I do a packet tracer it says that the global implicit deny rule is blocking it, but I tried to add a permit all in front of it and it still blocks it. Everything is configured correctly from what I can tell and the static routes and routing are correct. This has me baffled. Does anyone know what might be causing this or what I should look at in the config to get this working?

    Hi Mark,
          Talking of packet tracer, it would give you correct output for a through the box traffic, not for to the box or from the box traffic.
    So firstly we have two questions:
    1) Is this a through the box traffic, then you need to permit the traffic through ACL(if from lower sec level to higher) and add a NAT statement(depending on the ASA IOS Version you are using anything above 8.2.5 wont require a NAT).
    2) If this is a syslog from the firewall scenario, then you need to make sure to get the following logging configuration on ASA
    -enable logging
    -logging host management X.X.X.X --------(X.X.X.X is the ip of the syslog server)
    -logging trap debugging ----------(debugging is the level, you could use any other too, but to check would sugest this one)
    -Further if you have already sorted out till here, get us the following outputs:
    -show run
    -show logging
    -show logging queue
    Hope it helps
    Cheers,
    Naveen
    Please Rate Helpful posts.

  • Monitoring Cisco UCS Manager via HP System Information Manager 7.1 (SIM)

    I am working with a customer to configure HP System Information Manager 7.1 (SIM) to monitor their Cisco UCS Manager.
    The customer is looking to monitor the following:
    - CPU Utilization on manager, blades, servers, etc...
    - Memory utilization
    - Network utilization
    - System inventory
    Alerting is needed for the following:
    - Hardware failures: memory, power supply, drive, etc...
    - Predictive failures
    - Alert messages
    I have the list of all the MIBs provided by Cisco but an having the following issues while loading them into HP SIM.
    While loading MIB "CISCO-UNIFIED-COMPUTING-TC-MIB" I get the following error message:
    Line 128: Error defining object: expected a label, found reserved symbol {
    Line in MIB: SYNTAX Gauge32 {
    Guage32 is imported from SNMPv2-SMI MIB
    To get past this error I found a version of the MIB that removes all the textual conventions that where causing errors.  I have attached the fixed MIB file to this discussion. With the fixed version of the MIB installed in SIM everything compiles and installs except the following two MIBS. CISCO-UNIFIED-COMPUTING-NOTIFS-MIBCISCO-UNIFIED-COMPUTING-CONFORM-MIB Questions:
    1. Is there any way to get the CISCO-UNIFIED-COMPUTING-TC-MIB MIB to install correctly into HP SIM?
    2. Is my MIB load order setup correctly?
    3. Has anyone had success getting HP SIM to monitor and alert for Cisco UCS manager?
    MIB Load Order:
    SNMPv2-SMI
    SNMPv2-TC
    SNMP-FRAMEWORK-MIB
    RFC1213-MIB
    IF-MIB
    CISCO-SMI
    CISCO-ST-TC
    ENTITY-MIB
    INET-ADDRESS-MIB
    CISCO-UNIFIED-COMPUTING-MIB
    CISCO-UNIFIED-COMPUTING-TC-MIB
    CISCO-UNIFIED-COMPUTING-FAULT-MIB
    CISCO-UNIFIED-COMPUTING-NOTIFS-MIB
    CISCO-UNIFIED-COMPUTING-AAA-MIB
    CISCO-UNIFIED-COMPUTING-ADAPTOR-MIB
    CISCO-UNIFIED-COMPUTING-BIOS-MIB
    CISCO-UNIFIED-COMPUTING-BMC-MIB
    CISCO-UNIFIED-COMPUTING-CALLHOME-MIB
    CISCO-UNIFIED-COMPUTING-CAPABILITY-MIB
    CISCO-UNIFIED-COMPUTING-COMM-MIB
    CISCO-UNIFIED-COMPUTING-COMPUTE-MIB
    CISCO-UNIFIED-COMPUTING-CONFORM-MIB
    CISCO-UNIFIED-COMPUTING-DCX-MIB
    CISCO-UNIFIED-COMPUTING-DHCP-MIB
    CISCO-UNIFIED-COMPUTING-DIAG-MIB
    CISCO-UNIFIED-COMPUTING-DPSEC-MIB
    CISCO-UNIFIED-COMPUTING-EPQOS-MIB
    CISCO-UNIFIED-COMPUTING-EQUIPMENT-MIB
    CISCO-UNIFIED-COMPUTING-ETHER-MIB
    CISCO-UNIFIED-COMPUTING-EVENT-MIB
    CISCO-UNIFIED-COMPUTING-EXTMGMT-MIB
    CISCO-UNIFIED-COMPUTING-EXTVMM-MIB
    CISCO-UNIFIED-COMPUTING-FABRIC-MIB
    CISCO-UNIFIED-COMPUTING-FC-MIB
    CISCO-UNIFIED-COMPUTING-FCPOOL-MIB
    CISCO-UNIFIED-COMPUTING-FIRMWARE-MIB
    CISCO-UNIFIED-COMPUTING-FLOWCTRL-MIB
    CISCO-UNIFIED-COMPUTING-HOSTIMG-MIB
    CISCO-UNIFIED-COMPUTING-IMGPROV-MIB
    CISCO-UNIFIED-COMPUTING-IMGSEC-MIB
    CISCO-UNIFIED-COMPUTING-IPPOOL-MIB
    CISCO-UNIFIED-COMPUTING-IQNPOOL-MIB
    CISCO-UNIFIED-COMPUTING-ISCSI-MIB
    CISCO-UNIFIED-COMPUTING-LICENSE-MIB
    CISCO-UNIFIED-COMPUTING-LLDP-MIB
    CISCO-UNIFIED-COMPUTING-LSBOOT-MIB
    CISCO-UNIFIED-COMPUTING-LSMAINT-MIB
    CISCO-UNIFIED-COMPUTING-LS-MIB
    CISCO-UNIFIED-COMPUTING-MACPOOL-MIB
    CISCO-UNIFIED-COMPUTING-MAPPINGS-MIB
    CISCO-UNIFIED-COMPUTING-MEMORY-MIB
    CISCO-UNIFIED-COMPUTING-MGMT-MIB
    CISCO-UNIFIED-COMPUTING-NETWORK-MIB
    CISCO-UNIFIED-COMPUTING-NWCTRL-MIB
    CISCO-UNIFIED-COMPUTING-ORG-MIB
    CISCO-UNIFIED-COMPUTING-OS-MIB
    CISCO-UNIFIED-COMPUTING-PCI-MIB
    CISCO-UNIFIED-COMPUTING-PKI-MIB
    CISCO-UNIFIED-COMPUTING-PORT-MIB
    CISCO-UNIFIED-COMPUTING-POWER-MIB
    CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB
    CISCO-UNIFIED-COMPUTING-PROC-MIB
    CISCO-UNIFIED-COMPUTING-QOSCLASS-MIB
    CISCO-UNIFIED-COMPUTING-SOL-MIB
    CISCO-UNIFIED-COMPUTING-STATS-MIB
    CISCO-UNIFIED-COMPUTING-STORAGE-MIB
    CISCO-UNIFIED-COMPUTING-SW-MIB
    CISCO-UNIFIED-COMPUTING-SYSDEBUG-MIB
    CISCO-UNIFIED-COMPUTING-SYSFILE-MIB
    CISCO-UNIFIED-COMPUTING-TOP-MIB
    CISCO-UNIFIED-COMPUTING-TRIG-MIB
    CISCO-UNIFIED-COMPUTING-UUIDPOOL-MIB
    CISCO-UNIFIED-COMPUTING-VM-MIB
    CISCO-UNIFIED-COMPUTING-VNIC-MIB
    References:
    ftp://ftp.cisco.com/pub/mibs/supportlists/ucs/ucs-manager-supportlist.html#_Toc303691433
    http://www.hp.com/wwsolutions/misc/hpsim-helpfiles/simsnmp.pdf

    Please post "debug ccsip messages".
    Based on your debug you are getting "Cause No. 38 - network out of order."
    You may want to bind SIP to an interface that the IP address is defined which Lync points to.
    Chris

Maybe you are looking for

  • Converting time stamp to double

    Hello, I am currently using the write to spreadsheet file.vi to save data. It looks something like this: I also want to add the date and time stamp into the saved data but do not know a way of converting a date and time stamp to 'double format'. When

  • Possible with XSLT mapping?

    Hi, I have source xml structure of format <Header fld1 fld2 fld3 fld4 fld5 fld6  ><line   fld7 fld8 fld9 </line></header> Header occurence is 1---unbounded and line occurence is 0---unbounded and line items can exist or not for some header items.for

  • How can I move the tabs below the address bar in linux/FF 24?

    I prefer the tabs to be under the address bar on my Firefox. Previously I could simply click or unclick an option to do this, and it remained the same as I upgraded. However, I recently moved to Linux Mint 16, and it had Firefox 24 already installed.

  • Swf and flv on different servers

    How do I set up a video for progressive download when the .swf is on a different server than the flv? I am entering an absolute url in the content path for the flv.

  • BT Cloud - no web upload button

    Just started to use bt cloud , can log in ok , but no webupload button on  the top i have a "add to bt cloud sync" Useing ie and windows 8 Any help please?