CISCO ISDN TP Link is not connecting on COM port

Hello All,
I am having CISCO ISDN TelePresence Link. I am connecting it through COM port I changed the serial port settings as per recommended settings shown in User Manual in my laptop but still console is not coming. Please help...
CISCO ISDN Telepresence Link 1.1
Regards,
Kiran Chavan.

Make sure you're using a standard serial cable, and not a cross-over/null-modem cable.
Double check that your terminal settings are correct for 115200, 8, 1, none (as per example PuTTY screenshot below).
Wayne
Please remember to rate responses and to mark your question as answered if appropriate.

Similar Messages

When I add a https link to quicklinks, when I click on it, the (:) after https does not go to the address bar and thus the link is not connected. This is happening for all quicklink bookmarks with https:

Question
When I add a https link to quicklinks, when I click on it, the (:) after https does not go to the address bar and thus the link is not connected. This is happening for all quicklink bookmarks with https: Is there a solution?

Try some basic troubleshooting.
'''Try Firefox Safe Mode''' to see if the problem goes away. [[Troubleshoot Firefox issues using Safe Mode|Firefox Safe Mode]] is a troubleshooting mode that turns off some settings, disables most add-ons (extensions and themes).
If Firefox is open, you can restart in Firefox Safe Mode from the Help menu:
*In Firefox 29.0 and above, click the menu button [[Image:New Fx Menu]], click Help [[Image:Help-29]] and select ''Restart with Add-ons Disabled''.
*In previous Firefox versions, click on the Firefox button at the top left of the Firefox window and click on ''Help'' (or click on ''Help'' in the Menu bar, if you don't have a Firefox button) then click on ''Restart with Add-ons Disabled''.
If Firefox is not running, you can start Firefox in Safe Mode as follows:
* On Windows: Hold the '''Shift''' key when you open the Firefox desktop or Start menu shortcut.
* On Mac: Hold the '''option''' key while starting Firefox.
* On Linux: Quit Firefox, go to your Terminal and run ''firefox -safe-mode'' <br>(you may need to specify the Firefox installation path e.g. /usr/lib/firefox)
When the Firefox Safe Mode window appears, select "Start in Safe Mode".<br>
[[Image:Safe Mode Fx 15 - Win]]
'''''If the issue is not present in Firefox Safe Mode''''', your problem is probably caused by an extension, and you need to figure out which one. Please follow the [[Troubleshoot extensions, themes and hardware acceleration issues to solve common Firefox problems]] article to find the cause.
''To exit Firefox Safe Mode, just close Firefox and wait a few seconds before opening Firefox for normal use again.''
When you figure out what's causing your issues, please let us know. It might help others with the same problem.

The Outlook links do not connect to Firefox even after setting the customize option in Default Programs. Please help.

The''' Outlook links do not connect to Firefox '''even after setting the customize option in Default Programs. Please help.

Message to Toad-Hall
Thank you, for that. To be sure, I tried your suggestion, and selected "System Proxy" as the choice, for Thunderbird and Firefox. Rebooted, and looked at the outcome.. NO Joy.. :-(
I believe that I shall send the output of the Error Log in my next post. Perhaps someone can point me in the right direction after looking at the Error.log.
Thank you...Toad Hall. If you think of something else to try, I am ALL ears.. I shall keep trying..

During iTunes restore: Could not connect to lockdown port. Error code 0xe8000065

I have been seeing the same error on multiple Windows 7 iTunes installations since the recent iOS 8.3 (and iTunes 12.1.2 update). During an attempt to restore a backup, the iPhone disconnected error appears in iTunes. Digging deeper into the logs, we see a USB connection error, and then a DLL loading error message (that may or may not be a red herring.)
Here is an anonymized log snippet:
[3248 @ Sun Apr 19 20:22:08 2015] [com.apple.console AppleMobileBackup.exe] WARNING: Restoring <udid snipped out> from <backup folder snipped out>
[3248 @ Sun Apr 19 20:22:38 2015] [(unknown facility) AppleMobileBackup.exe] AMDeviceConnect (thread 4140): Could not connect to lockdown port (62078) on device 1 - <udid snipped out>: 0xe8000065.
[3248 @ Sun Apr 19 20:22:38 2015] [(unknown facility) AppleMobileBackup.exe] _AMDNotifyHook (thread 4140): Could not load library SHLWAPI.dll from the AppleMobileDeviceSupport directory, C:\Program Files\Common Files\Apple\Apple Application Support\\SHLWAPI.dll.
[3248 @ Sun Apr 19 20:22:38 2015] [com.apple.console AppleMobileBackup.exe] ERROR: Error attaching to device
Here are things I've tried, as recommended by this support page iOS: Unknown error containing '0xE' when connecting to a Windows PC - Apple Support
restarting the computer
uninstalling iTunes from the computer, reinstalling, rebooting
reset settings on the target iPhone
swapping out for a different usb cable
swapping out for a different usb port on the computer
renaming the iPhone (as another thread from a few years ago suggests)
I'm very hesitant to try a factory restore via iTunes if the device is reporting USB connection severing, since we may end up with a bigger issue, like half-installed iOS
Has anyone seen this error lately as well? I'd love to find some more possible solutions to try.

Kelly Wilkerson wrote:
Could not load library SHLWAPI.dll from the AppleMobileDeviceSupport directory, C:\Program Files\Common Files\Apple\Apple Application Support\\SHLWAPI.dll.
I did also just notice the excess backslash in this path. I'll do some experimenting to see if that makes any difference referencing a file in Windows 7 (OSX is usually very forgiving of that in my experience, so it could be nothing.)

Error connecting to COM port

Hi everybody!
I have create the application use Labview 2009. My application connect to COM port. It is very good on my computer that installed Labview 2009. When I create Installer, I add NI Measurement & Automation Explorer 4.6 in Addtional Installer Item. But when I install application on other computer that dont install Labview, it don't recognized COM port. I check MAX 4.6 on this computer, it don't show Devices and interface.
Please help me!
Thanks!

Hi
Did you add NI VISA to your installer?
Kudos are welcome

Cannot log into blend and has said max attempts exceeded, Link will not connect either

I downloaded the Blend software on my macbook pro and it would not log in with my Blackberry ID. After 5 attempts it locked me out.
I reset my Blackberry ID and tried again, but it will not let me even attempt to login and says max attempts exceeded. I uninstalled and reinstalled and still the same problem. Also Link will not let me connect. Any ideas please? looks like I am going over to Iphone if this continues and bin my Z30.

Jeff,
Thanks for the info on policy settings.
Let's see: I had 8.1.5 installed and I tried the update to 10g but only works from 8.1.7 or 9i, so then uninstalled and re-tried to do fresh install in a different home (OraHome10 vs OraHome8). That didn't go so well--it changed my 8i somehow so 8i would no longer work. Then I tried fresh install of 9i with a new starter DB--couldn't get into that DB. So uninstalled 9i, uninstalled 10g, uninstalled 8i, deleted every reference to Oracle on my computer, registry, etc., and re-tried 10g. I even went and bought a registry cleaning tool to zap things to make sure it was clean. It looked like it installed fine, provided me with starter DB but I just can't get into it. I'll let you know if the policy setting works.
I'm trying to look on the bright-side and say that we are learning a lot!
Dave

NOT GETTING SAME COM PORT FOR MY APPLICATION

i am making an application to connect my PC serially to a microcontroller serially with a usb to RS232 cable. how should i code in my application to ensure that my serial connection always gets the same com port whenever the applivcation is running on an other PC? it is important to get the same com port on every machine every time else my labview coding for serial communication will fail. OR is there a better to do this. Can we code in labview so that it uses any free com port available on the PC? the user of the application must not be prompted to enter a free com port.
thanks for any help.
Attachments:
Untitled.png ‏32 KB

No need to shout or ring my PM box... We are all volunteers here and sometimes we sleep or eat. besides its a rather simple problem that a search on the forums would have gotten you here
My Tag cloud would have gotten you the this same example snippet :RenameAlias
Just use the system API to find all available serial devices. figure out which one is your uC (how depends on the connected device) and set the MAX Alias to "MyMicroController" or something meaningful
Jeff

Lab View is not detecting two com ports of system

Hi,
In my PC, three com ports are there COM1, COM4 and COM6. But when we create new visa resource name, lab view is detecting only COM1 port. I want to know is there any way to correct this.
Regards
Shivakumar Singh

Hi,
First of all check if the ports are visible in the NI MAX. If not, you can try to Create New Port by going into Measuremenmt & Automation Explorer. Assign the Port values accordingly. This can be done by right clicking on the Ports (Serial & Parallel) section of the Devices and Interfaces tree.
Regards,
Deepu.

Using VISA can not find the com port

I use visa read but can't find any com port in Windows 7.
How can i find the com port in Windows 7??
由 jw2002 在 06-28-2009 09:20 AM
上編輯的訊息
由 jw2002 在 06-28-2009 09:20 AM
上編輯的訊息
Solved!
Go to Solution.

Windows 7 is not officially supported by National Instruments as it hasn't even been released. That means you won't get any official support from NI on this.
That said, does your computer actually recognize a serial port? Do you have an actual serial port, or do you have some sort of virtual COM port, or are you using some sort of adapter, such as a USB to serial port box? If it's any of the latter, the most likely reason is a driver issue which needs to be written to be compatible with Windows 7.

Adobe Media Encoder Dynamic Link Server NOT CONNECTING to Premiere Pro

I have Media Encoder CS5, as part of the Creative Suite 5. My programs say that I have no updates to install, so everything is up to date.
I am having an issue with the dynamic link server.
Here's what has happened thus far.
Recently when I have tried to encode a project sequence from Adobe Premiere Pro it DOES NOT work. This is the first time that has happened.
I repeated the process and again, it still happened, unable to connect to the Dynamic Link.
The Error messages that I was getting was "could not read from source. Check if it has been moved or been deleted"
Once, I received this, I went to check to see if all files were linked properly, and they were. Everything was rendered and all was good in the timeline and the project itself.
Yet, again, the error message appeared.
Then I tested a previous project that I knew had been exported and worked through Adobe to Media Encoder. And all the files were linked properly and yet again received the error message I wrote above.
Then I thought the Dynamic Link itself wasn't working properly, so I tested importing an Adobe After Effects Comp into a Premiere Timeline and it DID WORK.
Then I went and tested if a video file of an already exported project would be able to sync to Media Encoder. And this WORKED.
I then went to add the file directly from Media Encoder and when I went to add a sequence from a saved Premeire File, it would take about 5 minutes "Connecting to Dynamic Link Server", to then state, "Connecting to Dynamic Link Server Failed"
My question is, how do I fix the dynamic link between Media Encoder and Premiere? Because, additionally, importing and After Effects Sequence works with Media Encoder.

I've been searching/troubleshooting for days, none of the firewall, new shortcuts in folder, antivirus, you name it I tried it even wiped my system which seemed to work at first..
What did it for me in the end was I had Dxtory (a software recorder, for recording gameplay) running on startup, and somehow it interfered with only Premiere projects in Media Encoder, I could still import AE projects go figure.
Check all the programs you have running or use sometimes, if they have some sort of hook into other programs/deal with video/codecs this could be your problem too!
Thanks to everyone trying to solve this problem!
-JonOfAllGames

24.7.0 update link does not connect to the update server

FirefoxESR 24.4.0 was bundled with Debian. For several days, I have gotten a popup message to install the security update, 24.7.0. The Mozilla link from within Firefox says I have the most up-to date version (24.4.0). Apper software manager says everything is current. Every time I click on the install link in the popup, the download window stays on the "connecting to update server..." screen indefinitely, never connecting. Firefox and everything else works fine, there is no apparent reason from this end why connection should not take place.

"The Debian build of Firefox 24.4.0esr is Not updated by Mozilla but by Debian."
Correct.
"If the 24.4.0esr you are trying to update is actually from Mozilla and not a third-party build then make sure the folder has read/write permissions for that Linux user."
It never gets as far as permissions or actually trying to download an update. When Firefox checks with Mozilla using Firefox's internal update check, it comes back as 24.4.0 being the latest version.
"The Firefox tarball from Mozilla.org is certainly not a one time install. "
What I meant by one time install is that nobody would go through the effort more than once, and then only if there were extraordinary circumstances.
"If you put it in a folder in Home or make sure the folder has read/write permissions if you put it elsewhere then you should get updates from Mozilla as they are released. "
The current version received an update notice from Mozilla. The link tries but never connects with the update server.
"The updates are by .mar files whether on Windows, Mac OSX or Linux. "
I've used Firefox for years, with both Windows and Linux. I've never had to deal with .mar files or .tar files, or manually installing. Everything has always been a one-click automated install for both initial installation and updates.
Also, I don't want to perform a manual install unless it is for critical software, like needed drivers, and there is no other way. I would like to let the system do the work of keeping track of everything installed and its update status. I switched to Debian stable for the stability and am generally trying to avoid introducing software from outside of the tested stuff in their repository. The only reason I've pursued this update at all is that it is a security update and installing it shouldn't really affect Debian's status tracking (unless I stick the new version somewhere else).
I'm assuming that sooner or later, Mozilla will fix whatever problems are preventing the update from working correctly, or Debian will put 24.7.0 in their repository.

Black berry link is not connecting with my Q5

Hi
I hv bought a Q5 mobile yesterday.My device is not appearing while i hv connected with blackberry links.
I hv tried to uninstall and reinstall the s/w and the problem remains same.. the USB connections are charging the mobile whereas the device is not getting connected.Strange....
Pl help

Hey Dubaiberry,
Welcome to the BlackBerry Support Community Forums.
Thanks for the question.
Are you using BlackBerry Link for PC or Mac? Also are you using the BlackBerry USB cord that came with the BlackBerry Q5? Have you tried a different USB port?
I look forward to your reply.
Cheers.
-ViciousFerret
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Like! for those who have helped you.
Click Accept as Solution for posts that have solved your issue(s)!

DB-link is not connected from Forms 10g

Hi,
I have created the db-link(visdev) from mytest schema to APPS schema -- created successfully
->Login to mytest schema and ran the query: select * from all_objects@dblink -- Return values.
-> I have used the same dblink with below code from Forms 10g (Datablock - Pre-insert trigger)
cursor_handle := dbms_sql.open_cursor;
dbms_sql.parse(cursor_handle, 'select decode(object_type,''TABLE'',''T'',''VIEW'',''V'',null) col1 from all_objects'||'@'||db-link, 1);
dbms_sql.define_column(cursor_handle,1,col1,30);
execute_feedback := dbms_sql.execute (cursor_handle);
execute_feedback := dbms_sql.fetch_rows(cursor_handle);
dbms_sql.column_value(cursor_handle,1,col1);
Its throws error in Pre-insert trigger : select decode(object_type,'TABLE','T','VIEW','V',null) col1 from all_objects@db-link ---- Not return values -- error out
I found this error using log message.
Can you please help us... its very critical for us.
Edited by: user775668 on Jun 17, 2011 5:46 AM
Edited by: user775668 on Jun 17, 2011 5:46 AM

In terms of trying to debug this why don't you login to your schema and create a view:
create view testview as select * from all_objects@dblink
and deal with that instead?
(You would need to grant permissions to that view.)
I mean as a way to keep the complex dbms_sql out of the loop and look
more to permissions and schema issues. In the long term the view hard codes the structure and is
not a good solution if the structure changes. I just mean as a test.
BTW you know there is an all_objects already? Didn't know if you meant that literally or not.
You could not use that name.

Cisco sg 100d unmanaged switch not connecting to network

I have a Cisco sg 100d-08 unmanaged switched that had been working just fine for several months but now devices attached to the network thru are no longer on the network. All lights are on indicating the ports are active. Tried power recycle but no joy. When I replaced the switch with an old Belkin model everything works fine. Is there anyway to reset this unmanaged switch or do I now just have an expensive paper weight?

When the management interface is part of VLAN x
Make sure that the management interface vlan id is set to 0 (untagged ) If the native vlan on the switch trunk connected to controller is vlan x. If the native vlan is something else make sure to tag the mangement interface vlan with x.
Another interesting thing that might happen with switch having the following command enabled:
SW(config)#dot1q tag native
In that case all trunk native vlan frames will be tagged , so you have to tag the management vlan on the controller as well in that case.
To be able to troubleshoot such connectivity problem, you should get the output of:
show run int
show interface <\\ > switchport
the latter command should be your best friend.
One recommondation, make sure to tag your management / ap-manager interface with vlan id to maintain QoS limiting based on dot1p values for downstream traffic from the wired side.
In the above scenario , If you can provide the output of show interface <\\> switchport
I should tell you why the recommended action solved your issue based on the above explanation, and if you would like I can maitain the tag for you.
Please Don't Forget to rate correct Answers

Cisco Unified Video Advantages is not connected to any phone

There are CME 4.1.0.1, cisco video advantage 2.0, Cisco IP Phone 7940,Cisco VT Camera.
Video advantage can`t see phone.
But with CIPC it works correct.
In logs I saw an error:
CDP Driver Open failed with error-code 00000002
What is a way to connect phone to VT advantage.
What is the way to connect Video advantage with IP phone?
thanks in advance.

plug ur desktop/laptop to the back of the IP PHONE's data port~ to associate with the Video Ad

CISCO ISDN TP Link is not connecting on COM port

Similar Messages

Maybe you are looking for