Cisco ISE NAD compatibility
Hello all,
Are the Small Business 500 series Switches (ESW520) and Linksys Switches supported by the Cisco Identity Services Engine 1.2.. I didn't see them in the compatibility Matrix ! Is there any way to make them working for ISE wired CWA?
Best Regards.
Thank you Venkatesh for the reply,
It's unfortunate to know that ESW500 series doesn't support CWA (because we are deploying ISE and there are many ESW and Linksys Switches here),So Can they support LWA or 802.1X with ISE?
The same questions for Linksys Switches, Can they support CWA, LWA or 802.1X Authentications using ISE?
Thank you so much.
Similar Messages
-
Cisco ISE 1.2 & Cisco WLC 5508 v7.6
Hi all,
we are planning to upgrade our WLC to 7.6 to fix a bug with FlexConnect Client ACLs but I have just seen on the Cisco ISE Compatibility table that the it only recommends up to v7.5 of the WLC 5508...
Cisco have told me to steer clear of 7.5 as it is in a defferred status, so does anyone know, or have running in a lab or production, ISE1.2 with a 5508 WLC v7.6 NAD ?
I would much rather know of any issues people are experiencing before hand than to have to go through a software upgrade and then rollback.
Thanks all
Mario De RosaHi Neno,
right I have this almost working now.
I have simplified the setup. I am not going to do any client provisioning at the moment.
So I can connect to the corporate SSID using EAP-TLS and I can successfully push the branch data VLAN upon successful authorisation.
Now I am trying to introduce the posture element & per user ACLs.
I have defined the redirect ACL & Flex ACL on the vWLC however the NAC agent will not pop-up. The client is in the right VLAN and the redirect ACL seems to be getting applied as the client does get an IP through DHCP. However, the client cannot ping the ISE or access the guest portal when I open the browser.
DNS resolution seems to be working fine.
VLAN220 is my datacentre VLAN which the Management Interface on the controller is plugged in to.
VLAN10 is the branch DATA VLAN.
below is some output to give you some more details...
(Cisco Controller) >show client detail 00:24:d6:97:b3:be
Client MAC Address............................... 00:24:d6:97:b3:be
Client Username ................................. [email protected]
AP MAC Address................................... 18:33:9d:f0:21:80
AP Name.......................................... test-flex-ap
AP radio slot Id................................. 0
Client State..................................... Associated
Client NAC OOB State............................. Access
Wireless LAN Id.................................. 2
Hotspot (802.11u)................................ Not Supported
BSSID............................................ 18:33:9d:f0:21:81
Connected For ................................... 128 secs
Channel.......................................... 6
IP Address....................................... 10.130.130.120
Gateway Address.................................. 10.130.130.1
Netmask.......................................... 255.255.255.0
IPv6 Address..................................... fe80::f524:1910:69f0:9482
Association Id................................... 1
Authentication Algorithm......................... Open System
Reason Code...................................... 1
Status Code...................................... 0
Client CCX version............................... 4
Client E2E version............................... 1
--More-- or (q)uit
Re-Authentication Timeout........................ 1651
QoS Level........................................ Silver
Avg data Rate.................................... 0
Burst data Rate.................................. 0
Avg Real time data Rate.......................... 0
Burst Real Time data Rate........................ 0
802.1P Priority Tag.............................. disabled
CTS Security Group Tag........................... Not Applicable
KTS CAC Capability............................... No
WMM Support...................................... Enabled
APSD ACs....................................... BK BE VI VO
Power Save....................................... OFF
Current Rate..................................... m13
Supported Rates.................................. 1.0,2.0,5.5,11.0,6.0,9.0,
............................................. 12.0,18.0,24.0,36.0,48.0,
............................................. 54.0
Mobility State................................... Local
Mobility Move Count.............................. 0
Security Policy Completed........................ No
Policy Manager State............................. POSTURE_REQD
Policy Manager Rule Created...................... Yes
AAA Override ACL Name............................ POSTURE_REDIRECT_ACL
AAA Override ACL Applied Status.................. Yes
--More-- or (q)uit
AAA Override Flex ACL Name....................... POSTURE_REDIRECT_ACL
AAA Override Flex ACL Applied Status............. Yes
AAA URL redirect................................. https://pdc-ise-man01.kier.group:8443/guestportal/gateway?sessionId=c8dc800a00000005b3e7e953&action=cpp
Audit Session ID................................. c8dc800a00000005b3e7e953
AAA Role Type.................................... none
Local Policy Applied............................. none
IPv4 ACL Name.................................... none
FlexConnect ACL Applied Status................... Yes
IPv4 ACL Applied Status.......................... Unavailable
IPv6 ACL Name.................................... none
IPv6 ACL Applied Status.......................... Unavailable
Layer2 ACL Name.................................. none
Layer2 ACL Applied Status........................ Unavailable
mDNS Status...................................... Disabled
mDNS Profile Name................................ none
No. of mDNS Services Advertised.................. 0
Policy Type...................................... WPA2
Authentication Key Management.................... 802.1x
Encryption Cipher................................ CCMP (AES)
Protected Management Frame ...................... No
Management Frame Protection...................... No
EAP Type......................................... EAP-TLS
FlexConnect Data Switching....................... Local
--More-- or (q)uit
FlexConnect Dhcp Status.......................... Local
FlexConnect Vlan Based Central Switching......... No
FlexConnect Authentication....................... Central
Quarantine VLAN.................................. 0
Access VLAN...................................... 220
Client Capabilities:
CF Pollable................................ Not implemented
CF Poll Request............................ Not implemented
Short Preamble............................. Implemented
PBCC....................................... Not implemented
Channel Agility............................ Not implemented
Listen Interval............................ 10
Fast BSS Transition........................ Not implemented
Client Wifi Direct Capabilities:
WFD capable................................ No
Manged WFD capable......................... No
Cross Connection Capable................... No
Support Concurrent Operation............... No
Fast BSS Transition Details:
Client Statistics:
Number of Bytes Received................... 33698
Number of Bytes Sent....................... 19397
Total Number of Bytes Sent................. 19397
--More-- or (q)uit
Total Number of Bytes Recv................. 33698
Number of Bytes Sent (last 90s)............ 19397
Number of Bytes Recv (last 90s)............ 33698
Number of Packets Received................. 283
Number of Packets Sent..................... 147
Number of Interim-Update Sent.............. 0
Number of EAP Id Request Msg Timeouts...... 0
Number of EAP Id Request Msg Failures...... 0
Number of EAP Request Msg Timeouts......... 0
Number of EAP Request Msg Failures......... 0
Number of EAP Key Msg Timeouts............. 0
Number of EAP Key Msg Failures............. 0
Number of Data Retries..................... 53
Number of RTS Retries...................... 0
Number of Duplicate Received Packets....... 2
Number of Decrypt Failed Packets........... 0
Number of Mic Failured Packets............. 0
Number of Mic Missing Packets.............. 0
Number of RA Packets Dropped............... 0
Number of Policy Errors.................... 0
Radio Signal Strength Indicator............ -42 dBm
Signal to Noise Ratio...................... 41 dB
Client Rate Limiting Statistics:
--More-- or (q)uit
Number of Data Packets Recieved............ 0
Number of Data Rx Packets Dropped.......... 0
Number of Data Bytes Recieved.............. 0
Number of Data Rx Bytes Dropped............ 0
Number of Realtime Packets Recieved........ 0
Number of Realtime Rx Packets Dropped...... 0
Number of Realtime Bytes Recieved.......... 0
Number of Realtime Rx Bytes Dropped........ 0
Number of Data Packets Sent................ 0
Number of Data Tx Packets Dropped.......... 0
Number of Data Bytes Sent.................. 0
Number of Data Tx Bytes Dropped............ 0
Number of Realtime Packets Sent............ 0
Number of Realtime Tx Packets Dropped...... 0
Number of Realtime Bytes Sent.............. 0
Number of Realtime Tx Bytes Dropped........ 0
Nearby AP Statistics:
test-flex-ap(slot 0)
antenna0: 14 secs ago.................... -51 dBm
antenna1: 14 secs ago.................... -37 dBm
test-flex-ap(slot 1)
antenna0: 14 secs ago.................... -51 dBm
antenna1: 14 secs ago.................... -54 dBm
--More-- or (q)uit
DNS Server details:
DNS server IP ............................. 10.0.17.31
DNS server IP ............................. 10.0.17.43
Assisted Roaming Prediction List details:
Client Dhcp Required: False
Allowed (URL)IP Addresses
(Cisco Controller) >
(Cisco Controller) >show wlan 2
WLAN Identifier.................................. 2
Profile Name..................................... Demo1x
Network Name (SSID).............................. Demo1x
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Enabled
Network Admission Control
Client Profiling Status
Radius Profiling ............................ Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Local Profiling ............................. Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Radius-NAC State............................... Enabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
--More-- or (q)uit
Number of Active Clients......................... 1
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
User Idle Timeout................................ Disabled
Sleep Client..................................... disable
Sleep Client Timeout............................. 12 hours
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... mario-test-flex-vwlc
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
WLAN Layer2 ACL.................................. unconfigured
mDNS Status...................................... Disabled
mDNS Profile Name................................ unconfigured
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
--More-- or (q)uit
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
--More-- or (q)uit
Radius Servers
Authentication................................ 10.0.16.111 1812
Accounting.................................... 10.131.16.111 1813
Interim Update............................. Disabled
Framed IPv6 Acct AVP ...................... Prefix
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Disabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Enabled
PSK..................................... Disabled
CCKM.................................... Disabled
--More-- or (q)uit
FT-1X(802.11r).......................... Disabled
FT-PSK(802.11r)......................... Disabled
PMF-1X(802.11w)......................... Disabled
PMF-PSK(802.11w)........................ Disabled
FT Reassociation Timeout................... 20
FT Over-The-DS mode........................ Enabled
GTK Randomization.......................... Disabled
SKC Cache Support.......................... Disabled
CCKM TSF Tolerance......................... 1000
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Enabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
flexconnect PPPoE pass-through................ Disabled
--More-- or (q)uit
flexconnect local-switching IP-source-guar.... Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional
PMF........................................... Disabled
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
Eap-params.................................... Disabled
AVC Visibilty.................................... Disabled
AVC Profile Name................................. None
Flow Monitor Name................................ None
Split Tunnel (Printers).......................... Disabled
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Disabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
--More-- or (q)uit
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
802.11u........................................ Disabled
MSAP Services.................................. Disabled
Local Policy
Priority Policy Name
(Cisco Controller) >
when debugging the client during redirect, this is the output and I cannot spot anything wrong here...
(Cisco Controller) >*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Adding mobile on LWAPP AP 18:33:9d:f0:21:80(1)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Association received from mobile on BSSID 18:33:9d:f0:21:8e
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Global 200 Clients are allowed to AP radio
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Max Client Trap Threshold: 0 cur: 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Re-applying interface policy for client
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be In processSsidIE:4850 setting Central switched to FALSE
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying site-specific Local Bridging override for station 00:24:d6:97:b3:be - vapId 2, site 'default-group', interface 'management'
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Local Bridging Interface Policy for station 00:24:d6:97:b3:be - vlan 220, interface id 0, interface 'management'
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Processing RSN IE type 48, length 22 for mobile 00:24:d6:97:b3:be
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Received RSN IE with 0 PMKIDs from mobile 00:24:d6:97:b3:be
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Updating AID for REAP AP Client 18:33:9d:f0:21:80 - AID ===> 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Central switch is FALSE
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name:
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfMsAssoStateInc
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Idle to Associated
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2:session timeout forstation 00:24:d6:97:b3:be - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Stopping deletion of Mobile Station: (callerId: 48)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Sending Assoc Response to station on BSSID 18:33:9d:f0:21:8e (status 0) ApVapId 2 Slot 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfProcessAssocReq (apf_80211.c:8294) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Associated to Associated
*spamApTask6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sent 1x initiate message to multi thread task for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be EAP-PARAM Debug - eap-params for Wlan-Id :2 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Connecting state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sending EAP-Request/Identity to mobile 00:24:d6:97:b3:be (EAP Id 1)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received Identity Response (count=1) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Resetting reauth count 1 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be EAP State update from Connecting to Authenticating for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticating state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=214) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be WARNING: updated EAP-Identifier 1 ===> 214 for STA 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 214)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Allocating EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 214, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=215) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 215)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 215, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=216) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 216)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 216, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=217) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 217)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 217, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=218) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 218)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 218, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=219) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 219)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 219, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=220) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 220)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 220, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=221) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 221)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 221, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=222) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 222)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 222, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=223) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 223)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 223, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=224) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 224)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 224, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=225) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 225)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 225, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Processing Access-Accept for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 acl from 255 to 255
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 Flex acl from 65535 to 65535
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created for mobile, length = 253
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created in mscb for mobile, length = 253
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 220
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Re-applying interface policy for client
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 1 on mobile
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Inserting AAA Override struct for mobile
MAC: 00:24:d6:97:b3:be, source 4
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting re-auth timeout to 1800 seconds, got from WLAN config.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Creating a PKC PMKID Cache entry for station 00:24:d6:97:b3:be (RSN 2)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting MSCB PMK Cache Entry 0 for station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Adding BSSID 18:33:9d:f0:21:8e to PMKID cache at index 0 for station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: New PMKID: (16)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Disabling re-auth since PMK lifetime can take care of same.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Client in Posture Reqd state. PMK cache not updated.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAP-Success to mobile 00:24:d6:97:b3:be (EAP Id 225)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Freeing AAACB from Dot1xCB as AAA auth is done for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be EAPOL Header:
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00000000: 02 03 5f 00 .._.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Starting key exchange to mobile 00:24:d6:97:b3:be, data packets will be dropped
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Entering Backend Auth Success state (id=225) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Received Auth Success while in Authenticating state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticated state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-key in PTK_START state (message 2) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be PMK: Sending cache add
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be EAPOL Header:
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00000000: 02 03 5f 00 .._.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Freeing EAP Retransmit Bufer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be apfMs1xStateInc
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central switch is FALSE
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Sending the Central Auth Info
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central Auth Info Allocated PMKLen = 32
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be PMK: pmkActiveIndex = 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
apfMsEntryType = 0 apfMsEapType = 13
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name:POSTURE_REDIRECT_ACL
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 6166, Adding TMP rule
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
type = Airespace AP - Learn IP address
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 ACL ID = 255, IPv
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5761, Adding TMP rule
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Replacing Fast Path rule
type = Airespace AP - Learn IP address
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 ACL ID = 255,
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*spamApTask6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be spamEncodeCentralAuthInoMsPayload: msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
apfMsEntryType = 0 pmkLen = 32
*DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 325,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP setting server from ACK (server 10.0.17.85, yiaddr 10.130.130.120)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 DHCP_REQD (7) Change state to WEBAUTH_REQD (8) last state DHCP_REQD (7)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) pemAdvanceState2 6671, Adding TMP rule
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Replacing Fast Path rule
type = Airespace AP Client - ACL passthru
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 A
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Successfully plumbed mobile rule (IPv4 ACL ID 1, IPv6 ACL ID 255, L2 ACL ID 255)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Plumbing web-auth redirect rule due to user logout
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Assigning Address 10.130.130.120 to mobile
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
*pemReceiveTask: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 Added NPU entry of type 2, dtlFlags 0x0
*IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Pushing IPv6 Vlan Intf ID 0: fe80:0000:0000:0000:f524:1910:69f0:9482 , and MAC: 00:24:D6:97:B3:BE , Binding to Data Plane. SUCCESS !! dhcpv6bitmap 0
*IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Link Local address fe80::f524:1910:69f0:9482 updated to mscb. Not Advancing pem state.Current state: mscb in apfMsMmInitial mobility state and client state APF_MS_STATE_A
*DHCP Socket Task: Aug 12 10:58:28.581: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 10:58:28.589: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:00:07.959: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:00:07.967: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:01:59.153: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
Can you see any obvious reason why the NAC agent wont pop up?
Thanks
Mario -
Remote Access VPN posturing with Cisco ISE 1.1.1
Hi all,
we would like to start using our ISE for Remote VPN access.
We have run a proof of concept with the ISE & IPEP with a Cisco ASA5505. We got the authentication working however posturing of the client did not work.
That was a few months ago and so I was wondering whether any design document is available specifically around Using the Cisco ISE for Authenticating & Posturing Remote Access VPN clients.
I understand that version 9 of the ASA code is supposed to eliminate the need for Inline Posture, does anyone know whether this will also allow posturing too?
We do intend to by Cisco ASR's aswell, but I am sceptical of this as i do not know how many VPN licenses you get out of the box. The ASA's we have allow up to 5000 IPSec VPNs without having to purchase any licensing. What I do not want to do is to switch to SSL VPNs as this again will increase cost.
I know ISR's are support NADs but what about ASRs? There is no mention.
Any advise will be appreciated!
MarioOK, I have come accross the Cisco Validated design for BYOD and in there it has a section about Authenticating VPNs.
thats great... however it does not mention using the Inline posture node. Does anyone know if there is a limitation using Inline Posture and SSL VPNs...?
essentially my requirements are
2-factor authentication VPN using a Certificate & RSA Token
Posturing of the VPN endpoint.
Ideally i would like to use IPSec VPNs as i have licenses already for these on my ASAs. But if it will only work with SSL & AnyConnect, then so be it.
Can anyone help?
Mario -
Cisco ISE - Reauthentication of client if server becomes alive again
Dears,
I have this case where Cisco ISE server is used to authenticate & authorize clients on the network.
I configured the switch port to authorize the client in case the ISE server is dead (or not reachable).
The thing is that I want to reauthenticate the client once the ISE server becomes alive again but I am not able to.. ("Additional Information is needed to connect to this network" bullet is not appearing and the client PC remains authenticated and assigned to the VLAN.
Below is the switch port configuration:
interface FastEthernet0/5
switchport access vlan 240
switchport mode access
switchport voice vlan 156
authentication event server dead action authorize vlan 240
authentication event server alive action reinitialize
authentication host-mode multi-domain
authentication order dot1x mab
authentication priority mab
authentication port-control auto
mab
dot1x pae authenticator
spanning-tree portfast
Anyone can help?
Regards,Please check whether the switch is dropping the connection or the server.
Symptoms or Issue
802.1X and MAB authentication and authorization are successful, but the switch is dropping active sessions and the epm session summary command does not display any active sessions.
Conditions
This applies to user sessions that have logged in successfully and are then being terminated by the switch.
Possible Causes
•The preauthentication ACL (and the subsequent DACL enforcement from Cisco ISE) on the NAD may not be configured correctly for that session.
•The preauthentication ACL is configured and the DACL is downloaded from Cisco ISE, but the switch brings the session down.
•Cisco ISE may be enforcing a preposture VLAN assignment rather than the (correct) postposture VLAN, which can also bring down the session.
Resolution
•Ensure the Cisco IOS release on the switch is equal to or more recent than Cisco IOS Release 12.2.(53)SE.
•Check to see whether or not the DACL name in Cisco ISE contains a blank space (possibly around or near a hyphen "-"). There should be no space in the DACL name. Then ensure that the DACL syntax is correct and that it contains no extra spaces.
•Ensure that the following configuration exists on the switch to interpret the DACL properly (if not enabled, the switch may terminate the session):
radius-server attribute 6 on-for-login-auth
radius-server attribute 8 include-in-access-req
radius-server attribute 25 access-request include
radius-server vsa send accounting
radius-server vsa send authentication -
Cisco ISE AD (Windows Server 2013) Authentication Problem
Background:
Deployed two Cisco ISE 1.1.3. ISE will be used to authenticate wireless users, admin access to WLC and switches. Backend database is Microsoft AD running on Windows Server 2012. Existing Cisco ACS 4.2 still running and authenticating users. There are two Cisco WLCs version 7.2.111.3.
Wireless users authenticates to AD through ACS 4.2 works. Admin access to WLC and switches to AD through ISE works. Wireless authentication using PEAP-MSCHAPv2 and admin access wtih PAP/ASCII.
Problem:
Wireless users cannot authenticate to AD through ISE. The below is the error message "11051 RADIUS packet contains invalid state attribute" & "24444 Active Directory operation has failed because of an unspecified error in the ISE".
Conducted a detailed test of AD from ISE. The test was successful and the output seems all right except for the below:
xxdc01.xx.com (10.21.3.1)
Pinged:0 Mins Ago
State:down
xxdc02.xx.com (10.21.3.2)
Pinged:0 Mins Ago
State:down
xxdc01.xx.com
Last Success:Thu Jan 1 10:00:00 1970
Last Failure:Mon Mar 11 11:18:04 2013
Successes:0
Failures:11006
xxdc02.xx.com
Last Success:Mon Mar 11 09:43:31 2013
Last Failure:Mon Mar 11 11:18:04 2013
Successes:25
Failures:11006
Domain Controller: xxdc02.xx.com:389
Domain Controller Type: Unknown DC Functional Level: 5
Domain Name: xx.COM
IsGlobalCatalogReady: TRUE
DomainFunctionality: 2 = (DS_BEHAVIOR_WIN2003)
ForestFunctionality: 2 = (DS_BEHAVIOR_WIN2003)
Action Taken:
Log on to Cisco ISE and WLC using AD credentials. This rules out AD connection, clock and AAA shared secret as the problem.
2) Tested wireless authentication using EAP-FAST but same problem occurs.
3) Detailed error message shows the below. This rules out any authentication and authorization polices. Before even hitting the authentication policy, the AD lookup fails.
12304 Extracted EAP-Response containing PEAP challenge-response
11808 Extracted EAP-Response containing EAP-MSCHAP challenge-response for inner method and accepting EAP-MSCHAP as negotiated
Evaluating Identity Policy
15006 Matched Default Rule
15013 Selected Identity Store - AD1
24430 Authenticating user against Active Directory
24444 Active Directory operation has failed because of an unspecified error in the ISE
4) Enabled AD debugging logging and had a look at the logging. Nothing significant and no clues to the problem.
5) Tested wireless on different laptos and mobile phones with same error
6) Delete and add again AAA Client/Devices on both Cisco ISE and WLC
7) Restarted ISE services
8) Rejoin domain on Cisco ISE
9) Checked release notes of ISE 1.1.3 and WLC 7.2.111.3 for any open caveats. Nothing found related to this problem.
10) There are two ISE and two WLC deployed. Tested different combination of ISE1 to WLC1, ISE1 to WLC2 etc. This rules out hardware issue of WLC.
Other possibilities/action:
1) Test it out on a different WLC version. Will have to wait outage approval to upgrade WLC software.
2) Incompatibility of Cisco ISE and AD running on Microsoft Windows Server 2012
Anyone out there experienced something similar of have any ideas on why this is happening?
Thanks.
Update:
1) Built another Cisco ISE 1.1.3 sever in another datacentre that uses the same domain but different domain controller. Thais domain controller is running Windows Server 2008. This works and authentication successful.
2) My colleague tested out in a lab environment of Cisco ISE 1.1.2 with Windows Server 2012. He got the same problem as described.
This leads me to think there is a compatibility issue of Cisco ISE with Windows Server 2012.Does anyone know if ISE 1.1.3 p1 supports AD DCs running 2012, if not which patch is required ot version?
Worryingly when ISE joins a 2012 DC it states it's connected successfully, and if another 2003 DC is available in that datacentre it will perform the auths against that DC whilst actually advertising (Connections in the GUI) that it's connected to the 2012 DC. We ended up mapping 8 PSN IP’s to another datacentre which has one Win2003 servers whilst the old 2003 DC is being promoted back, the 8 ISE servers started working, even though they still advertised they were connected to the 2012 DCs in the original datacentre - I performed a leave and join on one PSN and only then did it advertise that the node was connected to a DC in a different datacentre -
Does Cisco ISE 1.2 support Catalyst SRW224G4P and Small business ESW520 Switches?
Hello all,
Does Cisco ISE 1.2 support Catalyst SRW224G4P and Small business ESW520 Switches?
Best regards.Hi there, the link below outlines the ISE supported Cisco hardware:
http://www.cisco.com/c/en/us/td/docs/security/ise/1-3/compatibility/ise_sdt.html
Thank you for rating helpful posts! -
MAC OS X unable to download Cisco ISE supplicant agent
Hi,
I have a problem with MAC OS X clients unable to download the Cisco ISE supplicant agent using Safari browser but able to login on the ISE guest portal. If the same client was to login to the ISE guest portal using Firefox; it has no issues downloading the ise supplicant and posture agent.
I have tried to update the Java version on the client to the latest; however it does not resolve the issue. As I am new to MAC OS clients; I was wondering what may be the cause of the issue?
I have summarized the issue as follows:
1. MAC OS X 10.8 with safari 6 -- unable to download agent but can login successfully on the Cisco ISE guest portal
2. MAC OS X 10.8 with Firefox -- able to login to Cisco ISE guest portal and download agents; no issues
3. MAC OS X 10.7 with safari and firefox --- unable to download agent but can login successfully on the Cisco ISE guest portal
4. Windows XP & Windows 7 & Iphone/Ipad/Android -- able to login/download agent without any issues
Any suggestions is appreciated.
Thanks.For Agent Download Issues on Client Machine
• Ensure that a client provisioning policy exists in Cisco ISE. If yes, verify the
policy identity group, conditions, and type of agent(s) defined in the policy.
(Also ensure whether or not there is any agent profile configured under Policy >
Policy Elements > Results > Client Provisioning > Resources > Add > ISE
Posture Agent Profile, even a profile with all default values.)
• Try reauthenticating the client machine by bouncing the port on the access
switch.
Remember that the client provisioning agent installer download requires the following:
• The user must allow the ActiveX installer in the browser session the first time an agent is installed
on the client machine. (The client provisioning download page prompts for this.)
• The client machine must have Internet access.
Client Machine Operating Systems and Agent Support in Cisco ISE
Check the following link
http://www.cisco.com/en/US/docs/security/ise/1.1.1/compatibility/ise_sdt.html#wp95449 -
Is anyone else having problems with ISE admin/monitoring pages not working properly under IE9? I just completed an upgrade to ISE 1.1, and it seems more and more, when I try to manage the system with IE9, I will get the following error (host name changed to protect the inocent). I dont know if this is truly an IE9 issue, or the chrome plug-in we are forced to use. Works perfect under Firefox 11.0.
This webpage is not available
The webpage at https://iseserver.domain.com/mnt/pages/dashboard/dashboard.jsp?mnt_config_write=true&token=BEGIN_TOKENXspmm4x5AwFsV6NExIBAVA==END_TOKEN might be temporarily down or it may have moved permanently to a new web address.
Error 103 (net::ERR_CONNECTION_ABORTED): Unknown error.Supported Administrative User Interface Browsers
You can access the Cisco ISE administrative user interface using the following browsers:
•Mozilla Firefox 3.6 (applicable for Windows, Mac OS X, and Linux-based operating systems)
•Mozilla FireFox 9 (applicable for Windows, Mac OS X, and Linux-based operating systems)
•Windows Internet Explorer 8
•Windows Internet Explorer 9 (in Internet Explorer 8 compatibility mode)
Cisco ISE GUI is not supported on Internet Explorer version 8 running in Internet Explorer 7 compatibility mode. For a collection of known issues regarding Windows Internet Explorer 8, see the "Known Issues" section of the Release Notes for the Cisco Identity Services Engine, Release 1.1. -
Cisco ISE 1.1.3 - Node unreachable
Cisco ISE 1.1.3 is running in standalone mode, when I made any configuration it show me the notification that "Configuration changes has been recorded but remain pending" any idea experts what could be wrong here.
ThanksFor issues regarding this you need to check the Cisco ISE Operations > Troubleshoot > Diagnostic Tools > General Tools > Evaluate Configuration Validator options. It also validate the several check on the potential network access device (NAD) configuration issues, including AAA,RADIUS, profiler, and web authentication.
-
Good Day,
I have Cisco ISE 1.2 with Cisco 2960 NAD.
I configured the authorization for the employee successfully, but my issue is with the guest users the link is not redirected.
Please advise what I have put in the authentication policy default rule?? deny access ?
And on the switch I should put the guest connect to a specific ports or I have to configure specific VLAN in the authorization profile?
Appreciate your support,In your authorization policy you are giving your Wired-Guest the same result as Wired-Webauth.
First time through you don't know he's a guest so he hits Wired-Webauth and gets redirected. Second time through, you have him in guest flow, so you know he's an authenticated guest, he hits Wired-Guest, but you send him the same permissions "Web_Auth". Create a profile that you want to give to your authenticated guests - Guest_Allowed for instance. -
Good Morning,
I am conducting an implementation of Cisco ISE version 1.2.1.198 with all its features on a switch 3560-X and in the ISE compatibility chart the minimum version for this switch would be the IOS v 15.0.2-SE2 (ED).
My doubt is whether i need the feature ipbase or just the lanbase would be sufficient to meet all the features of 802.1x for the Cisco ISE.
I appreciate the attention and Thanks,Please see the "Cisco Secure Access and Cisco TrustSec Release 5.0 System Bulletin".
It notes that the 3560-X requires IP base license for all the 802.1X features. -
Cisco ISE deployment with HP Swithes
Is there any compatibility matrix of cisco ISE with HP access swithes or there is any features restriction on HP access layer. The HP switches do support 802.1x.
Thanks
QasimQasim,
The only compatibility with network access devices is all related to Cisco gear. It would be best to stick with a full supported solution for the sake of support. In my opinion this will be a nightmare to manage if an issue was to occur.
Thanks,
Tarik Admani
*Please rate helpful posts* -
Hi,
Is the following possible:
- let the ISE do the authentication and then proxy to another radius server which does the authorization.
At the moment we have a freeradius server that does the following:
1) authenticates 802.1x requests (eap-tls)
2) during authorization the server checks an external database that determines the vlan that should be returned (in radius attribute) based on originating switch and/or mac address.
I am checking if I can migrate to ISE but then the above would have to work.
For MAB I can easily do authentication/authorization on freeradius so I will proxy MAB requests to there.
regards
ThomasISE acts as a RADIUS proxy server by proxying the requests from a network access device (NAD) to a RADIUS server. The RADIUS server processes the request and returns the result to Cisco ISE. Cisco ISE then sends the response to the NAD
FYI
you can use the RADIUS server sequences to proxy the requests to a RADIUS server.
The RADIUS server sequence strips the domain name from the RADIUS-Username attribute for RADIUS authentications. This domain stripping is not applicable for EAP authentications, which use the EAP-Identity attribute. The RADIUS proxy server obtains the username from the RADIUS-Username attribute and strips it from the character that you specify when you configure the RADIUS server sequence. For EAP authentications, the RADIUS proxy server obtains the username from the EAP-Identity attribute. EAP authentications that use the RADIUS server sequence will succeed only if the EAP-Identity and RADIUS-Username values are the same. -
Hi Everyone,
We are a Small company with 400-Users and currently we are using ACS 4.2 at our company. we want to upgrade and use Cisco ISE Appliance instead.
I want to know is there any major changes in configurtaion between ACS 4.2 and the ISE Latest Verison..............?
Is there any Hardware (Switch or Cisco AP ) compatibility issues with using Cisco ISE. (we are currently using Cisco Cat 3550 and Cisco Aironet 2600 APs with the existing ACS4.2)
What ISE Series & what Soft version are the latest so i can order ?
Thank YouImran,
When ordering cisco ISE there are certain SKUs that will allow you purchase and deploy the equipment, however there are conditions where you will have to rely on an ATP to prepare, plan and implement the solution for you. Here is the information that you are looking for along with the hardware compatibility matrix.
http://www.cisco.com/en/US/prod/collateral/vpndevc/ps5712/ps11637/ps11195/guide_c07-656177.html
Q/A - (column indicates which ISE skus are ATP madantory)
http://www.cisco.com/en/US/prod/collateral/vpndevc/ps5712/ps11637/ps11195/qa_c67-658591.html
Network component compatibility matrix -
http://www.cisco.com/en/US/docs/security/ise/1.1.1/compatibility/ise_sdt.html
Tarik Admani
*Please rate helpful posts* -
Trying to load Balance several Cisco ISE servers.
Trying to load Balance several Cisco ISE servers. For persistence, Cisco recommends using Calling-Station-ID and Framed-IP-address...Session-ID is recommended if load balancer is capable of it. I have documentation for the Cisco ACE, but using F5 LTM's. Assuming this has to be done with an I-Rule as none of these are available as a default. Not sue where to begin. I tried attaching the Cisco PDF, but not able for whatever reason.
Please also keep in mind that When using a Load-Balancer (anyone's) you must ensure a few things.
Each PSN must be reachable by the PAN / MNT directly, without having to go through NAT (Routed mode LB, not NAT). No Source-NAT. This includes the Accounting messages, not just the Authentication ones.
This means the Load-Balancer must be in the direct path between the clients and the ISE PSNs.
Some organizations have used Policy Based Routing (PBR) to accomplish the path, without physically locating the Load-Balancer between the clients and the PSNs.
Endpoints (clients) must be able to reach each Policy Services Node Directly (not going through the VIP) for redirections/Centralized Web Authentication/Posture Assessments/Native Supplicant Provisioning, and more.
You may want to "hack" the certs to include the VIP FQDN in the SAN field (my next blog post should cover this trick).
Perform sticky (aka: persistence) based on Calling-Station-ID and Framed-IP-address.
VIP gets listed as the RADIUS server of each NAD for all 802.1X related AAA.
Dynamic-Authorization (CoA):
If you use Server NAT to replace the PSN IP address with the VIP Address for Change of Authorization, then you would use the VIP address as the Dynamic-Authorization (CoA) client.
Otherwise, use the real IP Address of the PSN, not the VIP.
The LoadBalancers get listed as NADs in ISE so their test authentications may be answered, to keep the probes alive.
ISE uses the Layer-3 Address to identify the NAD, not the NAS-IP-Address in the RADIUS packet. This is a big reason to avoid SNAT.
Failure Scenarios:
The VIP is the RADIUS Server, so if the entire VIP is down, then the NAD should fail over to the Secondary DataCenter VIP (listed as the secondary RADIUS server on the NAD).
Use probes on the Load-Balancers to ensure that RADIUS is responding, as well as HTTPS (at minimum).
LB Probes should send test RADIUS messages to each PSE periodically, to ensure that RADIUS is responding, not just look for open UDP ports.
LB Probe should also examine the response for HTTPS, not just look for the open port(s).
Use node-groups with the L2-adjacent PSN's behind the VIP.
If the session was in process and one of the PSN's in a node-group fails, then another member of the node-group will issue a CoA-reauth; forcing the session to begin again.
At this point, the LB should have failed the dead PSN due to the probes configured in the LB; and so this new authentication request will reach the LB & be directed to a different PSN…
Maybe you are looking for
-
Farmville will not load using Firefox, but it will with IE, for over a week now.
Farmville will not load using Firefox, but it will with IE, for over a week now. I have cleared the cache and cookies multiple times, updated flash player, did a virus and malware scan, allowed java script, allowed mozilla in the Windows firewall, co
-
An unexpected error j3dcore-d3d.dll
Hi, Could me someone help, please? I'm new with Java3D, I installed version 1.5.1 and just tried to run the HelloUniverse example. Maybe I have a problem with rendering? Many Thanks! The I get this: # An unexpected error has been detected by Java Run
-
Running OS command from PL/SQL
Hi All, Is there any way of running a Operating System command thru the PL/SQL Procedure. I am using oracle on the Unix Platform. Do help me. Thanks In advance, Nitin Jain
-
AD Password Sync Connector in SSL Mode
Hi, The AD Password Sycn connector works fine with non-SSL , but not in SSL mode. This is the log generated- Debug [11/19/12 15:35:08] Start getting config parameters from registry Debug [11/19/12 15:35:08] oimhost is Debug [11/19/12 15:35:08] abc.co
-
VO Attribute displaying lookup meaning for code
Hi experts, How to make a VO attribute display lookup meaning for the code stored in DB into the query results table? Regards Ari