Cisco LMS 2.5 supported switches

Hello guys,
I would like to consult you about the supported devices of the mentioned above version of LMS 2.5. I found very good tables for version 3.1 and 3.2 and also this one for the RME module for 2.5 -
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_resource_manager_essentials/4.0.3/device_support/table/RME403.html
http://www.cisco.com/en/US/products/sw/cscowork/ps2073/products_device_support_table09186a00803f30ac.html#wp177779
I am interested in particular to this version 2960-24PC-L. I will thankfull if somebody can provide me a statement that it is supported or not, or even better - have tested it .
greets,
Georgi

LMS 2.x is now end of engineering. There will be no more service packs or updates for it. You should strongly consider moving to LMS 3.x (3.2 is the latest version).
Device support is based off of sysObjectID. What is the sysObjectID of this switch?

Similar Messages

Cisco LMS Ipv6 Support

Hi,
Does cisco LMS v3.2 Support IPV6 in all modules ?
We will be migrating from V4 to V6 in some time from now
Thanks

It has limitied ipv6 support.
Details are outlined here:
http://www.cisco.com/en/US/customer/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/install/guide1/overview.html#wp1090361

Does Cisco ISE 1.2 support Catalyst SRW224G4P and Small business ESW520 Switches?

Hello all,
Does Cisco ISE 1.2 support Catalyst SRW224G4P and Small business ESW520 Switches?
Best regards.

Hi there, the link below outlines the ISE supported Cisco hardware:
http://www.cisco.com/c/en/us/td/docs/security/ise/1-3/compatibility/ise_sdt.html
Thank you for rating helpful posts!

Cisco LMS VS HP open view

Good day team,
is there any major difference between them more than the one belows
Cisco LMS
only cisco devices
easy to manage
can use cisco discovery
HP OPEN view
MultiVendor
hard to manage
can not use deivce discovery

Hi,
I dont have a much experience with HPOV, but i can share more benefits from what you have already mentioned about
CWLMS, due to which I think it surpasses HPOV in many sense.
CiscoWorks LMS is a very powerful management tools that simplify the configuration, administration, monitoring, and troubleshooting of Cisco networks.
Following are some of the more detailed features which separate LMS from any other NMS software :
> A strong next-generation device discovery is done using cisco Propreitary CDP and other new technologies, modules and protocols like HSRP, ARP, BGP, OSPF, Cluster Discovery Module, LLDP, and routing Table as well.
> Real-time network fault analysis with easy-to-deploy, device-specific, best-practice templates.
> Hardware and software inventory management, centralized configuration tools, and syslog monitoring.
> Monitoring and tracking of network response time and availability via IP SLA
> Real-time device and link management, as well as port traffic management, analysis, and reporting.
> Support for network virtualization through configuration, reporting, monitoring and troubleshooting for VRFLite networks.
> More quickly and reliably utilize Cisco best practices using Cisco Smart Business Architecture (SBA) templates.
> LMS has Smart Services Interaction for contextual Technical Assistance Center (TAC) case creation and Cisco Support Community and it's interaction can Smartly tap into the Cisco Support Community knowledge base, streamline interactions with TAC.
> Cisco Prime LMS manages the deployment of the latest Cisco technologies and services such as medianet, Cisco TrustSec, and EnergyWise.
> A very crucial support for End-host manangement, including a separate IP Phone information.
> An integrated Inventory, software and configuration archive mechanism.
> Get immediate up-to-date information about the network through flexible reporting for inventory, user tracking, compliance, switch port usage, end-of-sale, PSIRT, and other critical areas.
> Easily manage all phases of the end-to-end lifecycle of Cisco value-added technologies and solutions, such as medianet, EnergyWise, TrustSec and Identity, Auto Smartports, and Smart Install.
A better comparison, if you are planning to get one, is ofcourse by using both of them. A evaluation Copy of Ciscoworks can anytime be downloaded from :
http://www.cisco.com/en/US/products/ps11200/index.html
Hope it helps!
-Thanks
Vinod

Cisco LMS 4.0 Graph some time not coming

I have installed cisco lms 4.0.
I have added 10 devices, previously it was working fine, Since last few days some time syslog and graph are not coming. after every reboot on server it started working. It is happening on daily.plz help me out with permanent solution
and also i have added manualy one device 7609-s router but not able to see cisco view
Error:-
Cannot find applicable device package for 10.133.224.131.
This error could be due to one of the following:
- The device package for this device type is not installed.
- Device support for this device type is not available.
- You are trying to open a component inside a device.
To correct the problem, either install a device package for the device type, or open the parent device to manage the component.
In device attribute it is showing 868 integrated router, I had try to delete and add again but problem is still same...
Windows 2008 r2 standard
RAM-16 Gb, Swap memory 8096

Evrything looks good. Are you able to access LMS in the server itself? Try to install another browser on your server and try to login.
Try both :
http://x.x.x.x:1741
https://x.x.x.x:443
Share NMSROOT/MDC/tomcat/logs/stdout.log and stderr.log.
-Thanks

Cisco ISE and Fast User Switching

Greetings,
In our deployment, we are interested in utilizing the "Fast User Switching" that is contained within the Windows Functionality. After searching for quite a while, I see that the native Windows supplicant is not compatible with Fast User Switching. It does not appear that Anyconnect is either. Can you please inform me as to what suppluicant I would need to research in order to allow for the User Switchign Functionality?
We are currently using ISE 1.2 Patch 4.
Thank You for any assistance.
David

The NAC Agent for Cisco ISE does not support Windows Fast User Switching when using the native supplicant. This is because there is no clear disconnect of the older user. When a new user is sent, the Agent is hung on the old user process and session ID, and hence a new posture cannot take place. As per the Microsoft Security policies, it is recommended to disable Fast User Switching.
Source:
http://www.cisco.com/en/US/docs/security/ise/1.2/user_guide/ise_pos_pol.html

Upgrading from cisco LMS 3.0 to a latest version

Hello,
Upgrading from cisco LMS 3.0 to a higher version.
Whatdoes it require?.
What is the current version?
What do we need for upgrading?
Are there specific codes or new need to buy new products?
In case of buying new products, which are the configurations?

H Malik,
You are correct! Latest version is Cisco prime LMS 4.2. There is no direct upgrade from LMS 3.x to LMS 4.x.
The procedure is simple:
Take backup orf old LMS --> Un-install (if same machine)--> Install new LMS --> Restore backup to get old data.
You would need to purchase new license for it.Cisco Prime LMS is now part of the Cisco Prime Infrastructure bundle and is not orderable separately. Cisco Prime Infrastructure bundle follows a size-based incremental licensing model. Device licenses can be combined and added when applied to a single server installation instance. Customers have the option of adding incremental licenses for additional devices as their network grows.Refer to the Cisco Prime Infrastructure Ordering Guide located at http://www.cisco.com/go/primeinfrastructure for the exact part number that matches your requirement and placing the order.
Currently even SmartNet or SAS contracts does not cover major upgrades from LMS 2.x and 3.x; an upgrade part number will need to be purchased to move to Cisco Prime LMS 4.2. These upgrade part numbers reflect a significant discount to protect customers' investment in the Cisco Prime product line.
The data migration process will vary depending on the LMS version from which the data need to be migrated. Migrating data to LMS 4.2:
• LMS 4.2 supports local upgrade or direct inline upgrade only from LMS 4.0.1 and LMS 4.1.
• LMS 4.0 customers are encouraged to install LMS 4.0.1 before doing inline upgrade to LMS 4.2.
• LMS 3.2 and LMS 3.2 Service Pack 1 customers can do a remote upgrade through the LMS backup and restore mechanism.
• LMS 3.1, LMS 3.0, LMS 3.0 December 2007 Update, LMS 2.6, and LMS 2.6 Service Pack 1 customers need to do a remote upgrade to LMS 4.0.1 and then upgrade to LMS 4.2.
-Thanks
Vinod

Device Alert from Cisco LMS

Hi All,
I am currently getting buried in a flurry of alerts from Cisco LMS. However when I check on the device in fault manager or with Device Diagnostic Tools, I do not see any issues. Anyone have any ideas as to why these alerts are being generated? ( I have removed our specific info with xxxx)
Additionally, I don't want to seem like I am bashing the LMS product, but could these alerts be made any more cryptic?
ALERT ID                = 00001LI
TIME                    = Wed 24-Mar-2010 01:21:49 GMT-06:00
STATUS                  = Active
SEVERITY                = Critical
MANAGED OBJECT          = xxxx
MANAGED OBJECT TYPE     = Switches and Hubs
EVENT DESCRIPTION       = xxxx: Cisco Configuration Management Trap:InformAlarm; xxxx [xxxx]:Unresponsive;
ALERT ID                = 00001LI
TIME                    = Wed 24-Mar-2010 06:54:37 GMT-06:00
STATUS                  = Active
SEVERITY                = Critical
MANAGED OBJECT          = xxxx
MANAGED OBJECT TYPE     = Switches and Hubs
EVENT DESCRIPTION       = xxxx: STP Topology Change:MinorAlarm; xxxx [xxxx]:Unresponsive;
ALERT ID                = 00001LI
TIME                    = Wed 24-Mar-2010 13:13:16 GMT-06:00
STATUS                  = Active
SEVERITY                = Critical
MANAGED OBJECT          = xxxx
MANAGED OBJECT TYPE     = Switches and Hubs
EVENT DESCRIPTION       = xxxx: vlanTrunkPortDynamicStatusChange Trap:InformAlarm; xxxx [xxxx]:Unresponsive;
ALERT ID                = 00001LI
TIME                    = Wed 24-Mar-2010 13:13:52 GMT-06:00
STATUS                  = Active
SEVERITY                = Critical
MANAGED OBJECT          = xxxx
MANAGED OBJECT TYPE     = Switches and Hubs
EVENT DESCRIPTION       = xxxx: STP Topology Change:MinorAlarm; ess016184.casino.sk.ca: vlanTrunkPortDynamicStatusChange Trap:InformAlarm; xxxx[xxxx]:Unresponsive;
ALERT ID                = 00001LI
TIME                    = Wed 24-Mar-2010 14:05:49 GMT-06:00
STATUS                  = Active
SEVERITY                = Critical
MANAGED OBJECT          = xxxx
MANAGED OBJECT TYPE     = Switches and Hubs
EVENT DESCRIPTION       = xxxx: vlanTrunkPortDynamicStatusChange Trap:InformAlarm; xxxx: STP Topology Change:MinorAlarm; xxxx [xxxx]:Unresponsive;
Thanks,
Rick

The alerts are quite generic. The individual EVENT details will contain many more details. Initially, it looks like DFM is showing you trap information relating to config and STP changes. If you have determined that these are not important, then you can clear the events (or mark them as acknowledged). If you're receiving these as notifications (e.g. email notifications), you might consider creating event sets to filter the events to just the ones in which you are interested, then unchecking the boxes for alerts in your Notification Group.

Cisco lms - config collection

Hi, i'm looking for a way to collect config's from specific devices periodically, is this possible?
for example, collect configs from firewalls everyday at midnight , and collect routers config once a week.
firewalls: (about 3 devices, config changes every day)
routers: (about 800 devices, rarely change the config)
the only config collection schedule i have found so far is too simple:
admin > collection settings > config > config collecion settings > periodic collection
second question, is it possible for cisco lms to send via e-mail the diff of the config pulled from devices? i mean the specific commands that have appeared in the new configuration file.
regards, ignacio

Unfortunately, LMS syslog mechanism is very minimalistic and doesn't have a lot of options to it.
However, the feature you're requesting is not very much LMS dependent. As, Ciscoworks depends on the kind of syslog message it receives from device, based on it, it captures some characters to send a notification as automated actions.
So usually it is the device which won't send a lot of information on what changes was done by which user in normal IOS syslog messages.
But, to certain extent, you can try to configure you device for Configuration-Change logger to receive details on what changes were made by users and check it on the syslog report, or configure AA on it for all or important devices.
You can enable a configuration logger to keep track of configuration changes made with the command-line interface (CLI). When you enter the logging enable configuration-change logger configuration command, the log records the session, the user, and the command that was entered to change the configuration. You can configure the size of the configuration log from 1 to 1000 entries (the default is 100). You can clear the log at any time by entering the no logging enable command followed by the logging enable command to disable and reenable logging.
Use the:
show archive log config {all | number [end-number] | user username [session number] number [end-number] | statistics} [provisioning] privileged EXEC command to display the complete configuration log or the log for specified parameters.
This example shows how to enable the configuration-change logger and to set the number of entries in the log to 500:
Switch(config)# archive
Switch(config-archive)# log config
Switch(config-archive-log-cfg)# logging enable
Switch(config-archive-log-cfg)# logging size 500
Switch(config-archive-log-cfg)# end
So, in all, it depends on the device and the kind of syslogs it send for LMS to react on it.
-Thanks
Vinod
**Encourage Contributors. RATE Them.**

Cisco SUP MGMT Interface Support L2 switchport mode?

Does the Cisco Supervisor MGMT interface support to be converted to a switchport to be assigned to a specific VLAN? The same question for 3750 switches and other switches.

No. They do need to have an IP address configured as they are actually routed ports.
The address needs to be in the subnet associated with the VLAN it plugs into in the switching infrastructure.

Cisco 7606 stacked VLAN support

Hi All,
Does Cisco 7606 GigabitEthernet modules support stacked VLAN (two VLAN tags)?
If yes, how do I configure it?
Thanks in advance.
Regards,
Sarah

Hi Sean,
Yes, it is QinQ tunneling. I am using Cat6k-Sup720.
Cisco7606(config-vlan)#?
VLAN configuration commands:
are Maximum number of All Route Explorer hops for this VLAN (or
zero if none specified)
backupcrf Backup CRF mode of the VLAN
bridge Bridging characteristics of the VLAN
exit Apply changes, bump revision number, and exit mode
media Media type of the VLAN
mtu VLAN Maximum Transmission Unit
name Ascii name of the VLAN
no Negate a command or set its defaults
parent ID number of the Parent VLAN of FDDI or Token Ring type VLANs
private-vlan Configure a private VLAN
remote-span Configure as Remote SPAN VLAN
ring Ring number of FDDI or Token Ring type VLANs
said IEEE 802.10 SAID
shutdown Shutdown VLAN switching
state Operational state of the VLAN
ste Maximum number of Spanning Tree Explorer hops for this VLAN (or
zero if none specified)
stp Spanning tree characteristics of the VLAN
tb-vlan1 ID number of the first translational VLAN for this VLAN (or
zero if none)
tb-vlan2 ID number of the second translational VLAN for this VLAN (or
zero if none)
Regards,
Sarah

Icmp Jitter collector configuration with Cisco LMS

Hi,
I am trying to collect jitter information of cisco Routers which are added in Cisco LMS
I have configured collector icmp jitter for them but somehow no stats are visible in lms and its says in IPM that u have no jitter collectors configured.
Do i need to enable anything on the Router as well to export stats to LMS ?
Thanks

Hi,
show ip sla application
IP Service Level Agreements
Version: Round Trip Time MIB 2.2.0, Infrastructure Engine-II
Time of last change in whole IP SLAs: *07:35:21.730 UTC Thu Mar 13 2014
Estimated system max number of entries: 27977
Estimated number of configurable operations: 27976
Number of Entries configured : 1
Number of active Entries : 1
Number of pending Entries : 0
Number of inactive Entries : 0
Supported Operation Types
Type of Operation to Perform: dhcp
Type of Operation to Perform: dns
Type of Operation to Perform: echo
Type of Operation to Perform: frameRelay
Type of Operation to Perform: ftp
Type of Operation to Perform: http
Type of Operation to Perform: icmpJitter
Type of Operation to Perform: jitter
Type of Operation to Perform: pathEcho
Type of Operation to Perform: pathJitter
Type of Operation to Perform: slm controller
Type of Operation to Perform: slm frame-relay interface
Type of Operation to Perform: slm frame-relay pvc
Type of Operation to Perform: slm interface
Type of Operation to Perform: tcpConnect
Type of Operation to Perform: udpEcho
Type of Operation to Perform: voip
IP SLAs low memory water mark: 38288719
The device is a Cisco 1841

LMS 4.0 support for ASA firewall

I need to add ASA 5520 to LMS 4.0, mainly for configuration archiving. ASA seems to be supported on LMS 3.2 as per the below link.
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/device_support/table/lms32sdt.html
I had directly added the ASA to the DCR, with the right login credentials and SNMPv3 strings , but still LMS fails to detect the ASA.
Thanks in advance.

Thanks Nael for the reply, please find below the SNMP configuration on the ASA
snmp-server group SNMPGRP v3 auth
snmp-server user SNMPUSR SNMPGRP v3 encrypted auth md5 a9:ba:79:44:5b:b0:98:65:88:30:a1:8b:7b:69:a2:9c
snmp-server host inside 10.88.80.11 trap version 3 SNMPGRP
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
The show version is given below.
ASA5520# sh ver
Cisco Adaptive Security Appliance Software Version 8.2(3)
Compiled on Fri 06-Aug-10 07:51 by builders
System image file is "disk0:/asa823-k8.bin"
Config file at boot was "startup-config"
ASA5520 up 8 days 19 hours
failover cluster up 25 days 14 hours
Hardware:   ASA5520, 512 MB RAM, CPU Pentium 4 Celeron 2000 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
                             Boot microcode   : CN1000-MC-BOOT-2.00
                             SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
                             IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
0: Ext: GigabitEthernet0/0 : address is 001f.9e50.8a24, irq 9
1: Ext: GigabitEthernet0/1 : address is 001f.9e50.8a25, irq 9
2: Ext: GigabitEthernet0/2 : address is 001f.9e50.8a26, irq 9
3: Ext: GigabitEthernet0/3 : address is 001f.9e50.8a27, irq 9
4: Ext: Management0/0       : address is 001f.9e50.8a28, irq 11
5: Int: Internal-Data0/0    : address is 0000.0001.0002, irq 11
6: Int: Internal-Control0/0 : address is 0000.0001.0001, irq 5
Licensed features for this platform:
Maximum Physical Interfaces    : Unlimited
Maximum VLANs                  : 150
Inside Hosts                   : Unlimited
Failover                       : Active/Active
VPN-DES                        : Enabled
VPN-3DES-AES                   : Enabled
Security Contexts              : 2
GTP/GPRS                       : Disabled
SSL VPN Peers                  : 2
Total VPN Peers                : 750
Shared License                 : Disabled
AnyConnect for Mobile          : Disabled
AnyConnect for Cisco VPN Phone : Disabled
AnyConnect Essentials          : Disabled
Advanced Endpoint Assessment   : Disabled
UC Phone Proxy Sessions        : 2
Total UC Proxy Sessions        : 2
Botnet Traffic Filter          : Disabled
This platform has an ASA 5520 VPN Plus license.
Serial Number: JMXXXXX
Running Activation Key: XX
Configuration register is 0x1
Configuration last modified by enable_1 at 15:05:29.268 AST Sun Jun 12 2011
When I add the ASA to the LMS using SNMPv3, the Device Management shows a blue box with a question mark(shown below).
Is ASA supported on LMS 4.0 with SNMPv3? Doing a troubleshooting on the LMS shows that LMS might only support SNMPv1 & v2.

Cisco LMS - Check for multiple words?

Can anyvbody help me out with a Cisco LMS query.
I'm doing a complaince check for snmp-server location
+snmp-server location [#.*#]
But I assume as I've got mulitple words which may vary it shows as not present in the complaince check even though it's in the config.
e.g. snmp-server location Martin's house in the middle of Scotland
I think [#.*#] stands for a missing string but not for multiple words, can anyone help me out with what I could use for multiple words?
Thanks in advance
Martin

I could solve the monitoring issue with snmp context configuration. I had to map each OSPF process to a snmp community. So i could retrieve data for each OPSF process. My issue now is how to add multiple communities to an LMS controlled device.
As far as i know, LMS support only one RO community per device.
regards
alex

Cisco LMS 3.2 SYSLOG not storing after 10 days

Hi ,
Im facing one issue with Cisco LMS 3.2
Issue : The logs is generating only for 10 days and post that im not able to see the logs. I have not done any config changes. The only change i have done is i have completely reinstalled the LMS. i did multiple troubleshoot but not able to resolve this isse. It would be great If any some one is able to help me in this isse. Thanks.
Regards,
Juliet

Dear Vinod
Thanks for ur response and the problem has been resolved.
The purge policy was set to 60 days only .The problem in reports viewing setting.
Syslog folder under LMS would store syslog reports of both the device as well as applications for defined folder size , which in your case was 1 MB ( same can be viewed under log generator option). The older reports would get deleted from the folder upon reaching the limit.
The only way to view device syslog is under following option : Reports -> Reports Generator in LMS GUI where we will have to choose syslog with desired attribute.
Regards,
Juliet

Cisco LMS 2.5 supported switches

Similar Messages

Maybe you are looking for