Cisco LMS 3.2 SYSLOG not storing after 10 days

Hi ,
Im facing one issue with Cisco LMS 3.2
Issue : The logs is generating only for 10 days and post that im not able to see the logs. I have not done any config changes. The only change i have done is i have completely reinstalled the LMS. i did multiple troubleshoot but not able to resolve this isse. It would be great If any some one is able to help me in this isse. Thanks.
Regards,
Juliet

Dear Vinod
Thanks for ur response and the problem has been resolved.
The purge policy was set to 60 days only .The problem in reports viewing setting.
Syslog folder under LMS would store syslog reports of both the device as well as applications for defined folder size , which in your case was 1 MB ( same can be viewed under log generator option). The older reports would get deleted from the folder upon reaching the limit.
The only way to view device syslog is under following option : Reports -> Reports Generator in LMS GUI where we will have to choose syslog with desired attribute.
Regards,
Juliet

Similar Messages

Cisco ISE guest portal redirect not working after successful authentiation and URL redirect.

Hi to all,
I am having difficulties with an ISE deployment which I am scratching my head over and can't fathom out why this isn't working.
I have an ISE 3315 doing a captive webportal for my guest users who are on an SSID. The users are successfully redirected by the WLC to the following URL:https://x.x.x.x:8443/guestportal/Login.action?portalname=XXX_Guest_Portal
Now when the user passes through the user authentication splash screen they get redirected to https://x.x.x.x:8443/guestportal/guest/redir.html and recieve the following error:
Error: Resource not found.
Resource: /guestportal/
Does anyone have any ideas why the portal is doing this?
Thanks
Paul

Hello,
As you are not able to get the guest portal, then you need to assure the following things:-
1) Ensure that the two Cisco av-pairs that are configured on the authorization profile should exactly match the example below. (Note: Do not replace the "IP" with the actual Cisco ISE IP address.)
–url-redirect=https://ip:8443/guestportal/gateway?...lue&action=cpp
–url-redirect-acl=ACL-WEBAUTH-REDIRECT (ensure that this ACL is also defined on the access switch)
2) Ensure that the URL redirection portion of the ACL have been applied to the session by entering the show epm session ip command on the switch. (Where the session IP is the IP address that is passed to the client machine by the DHCP server.)
Admission feature : DOT1X
AAA Policies : #ACSACL#-IP-Limitedaccess-4cb2976e
URL Redirect ACL : ACL-WEBAUTH-REDIRECT
URL Redirect :
https://node250.cisco.com:8443/guestportal/gateway?sessionId=0A000A72
0000A45A2444BFC2&action=cpp
3) Ensure that the preposture assessment DACL that is enforced from the Cisco ISE authorization profile contains the following command lines:
remark Allow DHCP
permit udp any eq bootpc any eq bootps
remark Allow DNS
permit udp any any eq domain
remark ping
permit icmp any any
permit tcp any host 80.0.80.2 eq 443 --> This is for URL redirect
permit tcp any host 80.0.80.2 eq www --> Provides access to internet
permit tcp any host 80.0.80.2 eq 8443 --> This is for guest portal
port
permit tcp any host 80.0.80.2 eq 8905 --> This is for posture
communication between NAC agent and ISE (Swiss ports)
permit udp any host 80.0.80.2 eq 8905 --> This is for posture
communication between NAC agent and ISE (Swiss ports)
permit udp any host 80.0.80.2 eq 8906 --> This is for posture
communication between NAC agent and ISE (Swiss ports)
deny ip any any
Note:- Ensure that the above URL Redirect has the proper Cisco ISE FQDN.
4) Ensure that the ACL with the name "ACL-WEBAUTH_REDIRECT" exists on the switch as follows:
ip access-list extended ACL-WEBAUTH-REDIRECT
deny ip any host 80.0.80.2
permit ip any any
5) Ensure that the http and https servers are running on the switch:
ip http server
ip http secure-server
6) Ensure that, if the client machine employs any kind of personal firewall, it is disabled.
7) Ensure that the client machine browser is not configured to use any proxies.
8) Verify connectivity between the client machine and the Cisco ISE IP address.
9) If Cisco ISE is deployed in a distributed environment, make sure that the client machines are aware of the Policy Service ISE node FQDN.
10) Ensure that the Cisco ISE FQDN is resolved and reachable from the client machine.
11) Or you need to do re-image again.

TS3899 Outgoing Mail, Password Authentication not stored after upgraded to IOS6

Hi,
After upgraded to IOS6, my email setting failed to store password authentication. Everytime i have to go through the setting to send out email. Is this a bug in IOS6? I do not encounter this when my phone is still on IOS5.1.1
Best regards
Nic

Best to delete and start over, and again make sure all info is correct. If it doesnt work try doing it under other, but first restart your phone, hold down the home and off button till the apple symbol comes up. Then redo the acount as stated.

Outlook folders not stored after adding in Sync Wi...

In PC Sync you can run a wizard to change the settings.
There are two things going wrong with choosing the folders in Outlook that you want to synchronise,
You find the folders in this manner:
Open PC Sync in the main PC Suite window -> Click the button with the spanner (tool); the wizard starts -> Select the data you want to synchronise (Calendar, Contacts and so on) -> Click the spanner tool, this time with a star -> A window asks if I'm sure that I want to change the settings, I click the 'V' -> I Pass the window with the question to select a PC application, I click the arrow -> Again it is asked to selec the data (Calendar and so on), I click the desired categories and click the rightarrow again-> Again the question is to select the profile (only Outlook). At the bottonm there is a button with a folder-icon on it, click the buttton-> four data categories are shown: Calendar, Tasks, Contacts, Notes, each with a fillable field and a button with an opened folder. All the fields are filled with the standard folders (like Personal folders\Calendar) except the field for Notes, which is empty.
Problem 1: I choose a subfolder in Contacts by clicking on the button. It takes about 10 secs for the list of Outlook folders to open. I click the desired subfolder. It is shown in the field for contacts. Suppose I keep the field for Notes empty and click the 'V'. An errormessage window appears asking me to fill in a folder in Contacts, whilst there is a folder in the field Contacts. Do I fill in a folder in Notes, than the window with the category fields closes normally.
Anyone familiar with this strange situation?
Problem 2 is more annoying. I fulfill the wizard and there are no errormessages. I end up with a synchronisation.Then I restart the whole procedure: the wizard is run in exactly the same way. But the folders that I filled in are gone: I see the same default folders returned that you saw the first time and again there is nothing in the notes field.
This problem is very old. Some times the folders stay stored for a while, but now I can't even store them at all.
Anyone?

1) as the other poster suggested that you have teh
show artwork checked in preferences.
I do, and it does display artwork for songs that already have artwork before they're uploaded.
2) you are not manually updating - if you are you
have to delete the original song (no artwork) from
you iPod and add back the changed (i.e. with artwork)
version (for songs not all ready on iPOd just skip
your step 2 and problem should be resolved)
I see, that's the problem there. I don't automatically update, because my music library contains songs that I don't necessarily want to put on my iPod.
Bummer.
Do you know how to maintain two Libraries? Like one library exclusively for auto-updating the iPod and another with everything? I can handle the movement from ALL library to iPod library manually... It seems redundant, but it would make my life so much easier!
Thanks for both of your replies... very helpful!

CW LMS 3.0.1 not working after updating Campus manager to 5.0.6

Hi,
I upgraded my CW Campus Manager from 5.0.5 to 5.0.6, and now when I try to access CW I get :
Internal Server Error
The server encountered an internal error or misconfiguration and was unable to complete your request.
Any idea how to fix this?
Thanks in advance

Post the NMSROOT/MDC/Apache/logs/error.log and NMSROOT/MDC/tomcat/logs/stdout.log and stderr.log.

Cisco LMS 4.0 Graph some time not coming

I have installed cisco lms 4.0.
I have added 10 devices, previously it was working fine, Since last few days some time syslog and graph are not coming. after every reboot on server it started working. It is happening on daily.plz help me out with permanent solution
and also i have added manualy one device 7609-s router but not able to see cisco view
Error:-
Cannot find applicable device package for 10.133.224.131.
This error could be due to one of the following:
- The device package for this device type is not installed.
- Device support for this device type is not available.
- You are trying to open a component inside a device.
To correct the problem, either install a device package for the device type, or open the parent device to manage the component.
In device attribute it is showing 868 integrated router, I had try to delete and add again but problem is still same...
Windows 2008 r2 standard
RAM-16 Gb, Swap memory 8096

Evrything looks good. Are you able to access LMS in the server itself? Try to install another browser on your server and try to login.
Try both :
http://x.x.x.x:1741
https://x.x.x.x:443
Share NMSROOT/MDC/tomcat/logs/stdout.log and stderr.log.
-Thanks

LMS 4.0 not starting after upgrade

I am running LMS 4.0 on Windows 2008 Server, recently changed from eval copy to licensed (for 750 devices). It had been running and working for several months.The license application worked fine and it ran a couple days that way.
I then downloaded the CiscoWorks_LMS_4.0.x_WIN2K8_R2.exe patch so that I could upgrade the server OS to Windows Server 2008 R2. Per the instructions in the patch readme I first proceeded to upgrade my server to 2008 R2. Then I installed the patch (patch only).
After doing this (and restarting the server) CiscoWorks daemons will no longer start. I have confirmed my paging file size (swap) is set to start at 8192 MB (8 GB) as required. I tried manuallly starting (net start crmdmgtd) without sucess. I see the initial dmgt_start_lock lock file in C:\Program Files (x86)\CSCOpx\objects\dmgt\ready but none of the other process lock files ever pop in and out as they would normally and the processes (and thus CiscoWorks server) never start.
Any suggestions?

The "patch" is as far as I know some sort of launcher for the installation setup.exe.
When I run the "patch" al I get is the question where my installer is, so I can install LMS.
I have not yet tried to run this on an existing LMS installation. Nor upgrading the OS on an LMS installation :-)
Does the "patch" have a different behavior when LMS is already installed?
If not, I suggest to use the cleansystem.exe in the CSCOpx\bin to remove the current install, reinstall use the patch to launch the installer and restore a backup
Cheers,
Michel

Ipad2 shut off after down the battery but when connect the charger my ipad2 is not storing the power in the battery and i also not finding the error code ???

ipad2 shut off after down the battery but when i connect the charger with my ipad2, its not storing the power in the battery and i also not finding the error code ???

If you drained the battery, it may take a bit for it to come back. I'd plug it in and leave it for a few hours and see if it's charging.
If not, you can try to do a reset. Hold down the sleep and home keys for about 20 seconds. When you see the white apple, let go and let it reset and see if it charges.
It's also possible that your battery has reached the end of its life. THey can only handle a finite amount of recharge cycles. If you can't get it to hold a charge, then make an appointment at your local apple store and explore your other options.

Cisco 9971 "not registered" after Reset on CUCM 9.1

Hello everyone,
we are experiencing a strange problem with 9971 phones:
We have two CUCM 9.1 clusters
Our production-cluster: Publisher, 3 Subscribers, dedicated TFTP, Unity Connection, CUPS
and our Lab environmant: Publisher, 1 Subscriber, TFTP on Publisher, Unity Connection, CUPS
In our production environment, 9971 phones work fine
In our lab environment, 9971 also work fine at first, but after some hours, sometimes days, or after a phone is resettet manually via CUCM administration the phone won't register anymore. After the phone is rebooted, the display briefly shows the correct directory number and line but they disappear immediatley and the phone is stuck with "Phone not registered" after that. The only way I can get the phone to register again after that is to completely reset all settings on the phone.
Both clusters are located within the same subnet, as well as the phones use the same voice vlan (manual tftp setting in both cases). It doesn't seem to be a network-related issue.
I have tested the same devices with both clusters, so the devices themselves seem to work properly too.
Has anyone experienced this sort of problem before? Any help would be appreciated.
Thanks
Matthias

Hi Mark,
best I can provide you with at the moment is this:
Status Messages on the phone:
Updating Trust List
Trust List Updated
SEPE840....cnf.xml.sgn (http)
VPN Error: VPN is not Configured
Also, I have captured some Wireshark Traces. I took one phone that was registered and sent a reset request from the CUCM Web-Interface. The phone then rebooted and got stuck with "Phone not registered" as I described in my first post.
I unplugged the LAN cable, put it back in and captured what happened while the phone tried to register using a Span port at my access switch. You can find the pcap file attached to the first post.
Thanks
Matthias

Cisco LMS 4.0.1 to Prime Infrastructure 2.x Upgrade

Hello,
we are using Cisco LMS and want to upgrade to Cisco Prime Infrastructure.
Now we have received the following license update: L-L-PI2X-100-U - LMS to Prime Infrastructure 2.x Upgrade 100 Device
and I wonder what is the best way to upgrade.
After a long search I found the following document on cisco:
http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/prime-infrastructure/guide-c07-729990.html#wp9000727
There is only the talk of the upgrade from 4.2 LMS to Prime.
The problem is that we can not update to version 4.2 because of an error. Thats one reason why we need to upgrade to prime.
Is the only possibility now to export databases?
thanks in advance

Hi Heiko,
Upgarding from LMS 4.0.1 to LMS 4.2 , you need a New Licesne . Are you getting that error..
Upgarding from LMS to PI is alomost like a new Installation of PI. because only thing you can IMPORT from LMS to PI is the device list .
you can download the software from the below link:
http://software.cisco.com/download/release.html?mdfid=284422771&flowid=45323&softwareid=284272932&release=2.0.0&relind=AVAILABLE&rellifecycle=&reltype=all
Installation link:
http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-0/install/guide/Cisco_PI_Hardware_Appliance_Installation_Guide/cpi_higmain.html
hope it will help
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

Alerts from Cisco LMS

Dears I have some concerns about SNMP and Cisco LMS :
Our network device sent a LINK DOWN trap to CISCO LMS followed by LINK UP trap . I can see these messages from the device logs . My questions is :
1-If the device is configured correctly to send snmp traps .And the syslog is showing both messages (LINK DOWN , LINK UP) then we can say the device is sending the snmp traps ?
2-Why the LINK UP trap is missing in Cisco LMS .. What should we check to make sure LMS is sending and receiving these alert in proper way ???
Thanks in advance .

Hi ,
-If the device is configured correctly to send snmp traps .And the syslog is showing both messages (LINK DOWN , LINK UP) then we can say the device is sending the snmp traps ?
Syslogs are different from SNMP traps , If you are seeing syslogs for linkup and linkdown ,it does not mean that device is sending the SNMP traps as well.
2-Why the LINK UP trap is missing in Cisco LMS .. What should we check to make sure LMS is sending and receiving these alert in proper way ???
You can verify the snmp trap by packet capture
Thanks-
Afroz
****Ratings Encourages Contributors ****

Upgrade Cisco LMS to PI

We currently operate Cisco Prime LMS v4.1 and we're looking to upgrade Cisco PI (Prime Infrastructure) in the next few weeks.
Is there an upgrade path from Cisco LMS to PI? The reading I have completed seems to indicate that an upgrade can only be completed from Cisco NCS.
If I need to perform a new install of PI, can I somehow Migrate / Import my existing device database and config into the new software? I have configured some syslog fault rules for e-mail notification, config templates, custom reports, etc, that I would also like to keep and not necessarily recreate.
Thanks.

As cwallin noted, LMS 4.2.2 patch added the ability to migrate some information from LMS to PI.
Most customers would not be well-served by migrating a mature LMS implementation to PI at this time due to the fact that PI does not yet have feature parity with LMS, Even PI 2.0 (due out in a couple of months) will not have complete feature parity.
See this link for a current comparison.

Cisco LMS VS HP open view

Good day team,
is there any major difference between them more than the one belows
Cisco LMS
only cisco devices
easy to manage
can use cisco discovery
HP OPEN view
MultiVendor
hard to manage
can not use deivce discovery

Hi,
I dont have a much experience with HPOV, but i can share more benefits from what you have already mentioned about
CWLMS, due to which I think it surpasses HPOV in many sense.
CiscoWorks LMS is a very powerful management tools that simplify the configuration, administration, monitoring, and troubleshooting of Cisco networks.
Following are some of the more detailed features which separate LMS from any other NMS software :
> A strong next-generation device discovery is done using cisco Propreitary CDP and other new technologies, modules and protocols like HSRP, ARP, BGP, OSPF, Cluster Discovery Module, LLDP, and routing Table as well.
> Real-time network fault analysis with easy-to-deploy, device-specific, best-practice templates.
> Hardware and software inventory management, centralized configuration tools, and syslog monitoring.
> Monitoring and tracking of network response time and availability via IP SLA
> Real-time device and link management, as well as port traffic management, analysis, and reporting.
> Support for network virtualization through configuration, reporting, monitoring and troubleshooting for VRFLite networks.
> More quickly and reliably utilize Cisco best practices using Cisco Smart Business Architecture (SBA) templates.
> LMS has Smart Services Interaction for contextual Technical Assistance Center (TAC) case creation and Cisco Support Community and it's interaction can Smartly tap into the Cisco Support Community knowledge base, streamline interactions with TAC.
> Cisco Prime LMS manages the deployment of the latest Cisco technologies and services such as medianet, Cisco TrustSec, and EnergyWise.
> A very crucial support for End-host manangement, including a separate IP Phone information.
> An integrated Inventory, software and configuration archive mechanism.
> Get immediate up-to-date information about the network through flexible reporting for inventory, user tracking, compliance, switch port usage, end-of-sale, PSIRT, and other critical areas.
> Easily manage all phases of the end-to-end lifecycle of Cisco value-added technologies and solutions, such as medianet, EnergyWise, TrustSec and Identity, Auto Smartports, and Smart Install.
A better comparison, if you are planning to get one, is ofcourse by using both of them. A evaluation Copy of Ciscoworks can anytime be downloaded from :
http://www.cisco.com/en/US/products/ps11200/index.html
Hope it helps!
-Thanks
Vinod

Cisco lms - config collection

Hi, i'm looking for a way to collect config's from specific devices periodically, is this possible?
for example, collect configs from firewalls everyday at midnight , and collect routers config once a week.
firewalls: (about 3 devices, config changes every day)
routers: (about 800 devices, rarely change the config)
the only config collection schedule i have found so far is too simple:
admin > collection settings > config > config collecion settings > periodic collection
second question, is it possible for cisco lms to send via e-mail the diff of the config pulled from devices? i mean the specific commands that have appeared in the new configuration file.
regards, ignacio

Unfortunately, LMS syslog mechanism is very minimalistic and doesn't have a lot of options to it.
However, the feature you're requesting is not very much LMS dependent. As, Ciscoworks depends on the kind of syslog message it receives from device, based on it, it captures some characters to send a notification as automated actions.
So usually it is the device which won't send a lot of information on what changes was done by which user in normal IOS syslog messages.
But, to certain extent, you can try to configure you device for Configuration-Change logger to receive details on what changes were made by users and check it on the syslog report, or configure AA on it for all or important devices.
You can enable a configuration logger to keep track of configuration changes made with the command-line interface (CLI). When you enter the logging enable configuration-change logger configuration command, the log records the session, the user, and the command that was entered to change the configuration. You can configure the size of the configuration log from 1 to 1000 entries (the default is 100). You can clear the log at any time by entering the no logging enable command followed by the logging enable command to disable and reenable logging.
Use the:
show archive log config {all | number [end-number] | user username [session number] number [end-number] | statistics} [provisioning] privileged EXEC command to display the complete configuration log or the log for specified parameters.
This example shows how to enable the configuration-change logger and to set the number of entries in the log to 500:
Switch(config)# archive
Switch(config-archive)# log config
Switch(config-archive-log-cfg)# logging enable
Switch(config-archive-log-cfg)# logging size 500
Switch(config-archive-log-cfg)# end
So, in all, it depends on the device and the kind of syslogs it send for LMS to react on it.
-Thanks
Vinod
**Encourage Contributors. RATE Them.**

Cisco LMS - logs exceed limit

Hi friends,
First of all, let me introduce myself since I'm new with cisco community. I'm syafiq currently working as an network administrator in Malaysia.
I need guidance on cisco LMS as I'm really new with the LMS systems. Currently I'm having issue with LMS where the log files are exceeding the size limit set by pervious administrator. Can anyone help me on how to backup/ remove the logs file and set it to a new locations i.e. new drive ?
thanks in advanced!

Hi,
Welcome to CSC.
Ciscoworks has many features and all of those features has dedicated processes. All those processes and many ciscoworks agnets write their output (logggin) to the *.log files. Most of them are under NMSROOT/logs.
These files are usually not important enough (except syslog.log mostly) unless there is any issue with any of the LMS function and it needs to be t/shooted.
But these logs files should not be deleted, nor there data needs to be preserved for long, unless your organisation policy says so.
Because processes keeps on writing constantly to these log files, these log files can grow and can continue to grow to become extravagantly huge sometimes, hence need to be controlled, which is why the 'Logrot' feature was inlcuded.
Logrot is a log rotation program that enables you to control the log files size growth. It helps you to:
•Rotate log files while CiscoWorks is running.
•Optionally archive and compress rotated logs.
•Rotate log files only when they have reached a particular size.
You can configure it from :
Common Services > Server > Admin > Log Rotation
Please check configuring log Maintaining Log Files section of the user guide for more details.
-Thanks
Viinod

Cisco LMS 3.2 SYSLOG not storing after 10 days

Similar Messages

Maybe you are looking for