Cisco MDS 9509 and HP Blade server problem

I have a big problem , when i connected to MDS 9509 to HP VC-FC 8GB the module in MDS 9509 did not detect the HP module . I think this will be because MDS 9509 uses VSAN technology , but HP blade is not support this feature. Please help me

I am fairly certain that the HP blade chassis has HP branded Brocade FC switches. These switches need to be placed into AG mode and rebooted. On the Cisco MDS core the NPIV feature must be enabled.
Here is more info on the Brocade AG mode -
http://www.brocade.com/solutions-technology/technology/platforms/fabric-os/access_gateway.page
http://www.brocade.com/downloads/documents/data_sheets/product_data_sheets/AccessGateway_DS_02.pdf
Cisco NPIV info
http://www.cisco.com/en/US/prod/collateral/ps4159/ps6409/ps5989/ps9898/white_paper_c11-459263.html

Similar Messages

Migrating from Brocade 2800/ 3900 to Cisco MDS 9509

What is the best procedure from migrating from Brocade 2800/3900/12000 to Cisco MDS 9509 especially connected to HP-UX and AIX server.
Without any Downtime I should be able to migrate these servers.
I thought about these options:
1. Use vgexport and vgimport or exportvg and importvg (AIX) after connecting to Cisco MDS. But this requires complete downtime on the application.
2. Take one path down or HBA down and switch the cable and vgextend the devices.
Please let me know if somebody has procedure.
I was successful in HP-UX server using the second options but I cant see all the LUNs. That might be array specific problem also.
If anybody has detailed procedure on migrating this scenario. please let me know.
We are using Persistent FCIDs on our MDS switches.
Thanks in Advance

After connecting 1 cable from server HBA to Cisco S/w, why you are not able to see all LUNs, did you cross-check that...I mean HBA Configuration (max 256 LUNs) or Disk Array library driver to be installed on host side.if that can be sorted out, you can mirror the volumes across the disk arrays.are you using HDS Arrays? I don't know but what is vgextend command you are mentioning...
also did you take a reboot of server or is it online addition on new LUNs...
Also any how if you are not able to see all LUNs that is going to be an issue later as well for migration...pls cross-check that...

Best Design practices of SAN with the MDS 9513,MDS 9509 and Brocade 8510

Hi
Am searching best design to implement CISCO MDS 9513,9509, Brocade 8510,Storage and UCS all clubbed in the topology. And please suggest me any tool to compare MDS and Brocade 8510 performance.

Boomi,
Both MDS and Brocade will serve basic features of Storage networking. Both can be mix and match to achieve redundancy, which you already have. However, if you are looking for any tool or perfmon then there isn't much to compare. You can use IOmeter or Akkori. I see that you have enterprise level hardware in your setup. Not sure what other line cards you have installed and what application are running through, and if you have remote sites (SAN islands) then the real difference of features and best practices can be discussed. For example, IVR, FCIP, ISCSI, FCoE, etc.
Thanks,
Nisar
Sent from Cisco Technical Support iPad App

Creative cloud is working but the webpage cannot find the files and returns a SERVER PROBLEM

What is wrong since the latest updates of Creative Cloud ??
The upload is working fine but the Webpage is mostly not reachable and returns a SERVER error.

I always use the app on my iMac, since more then one year. The Creative Cloud is then Syncing my files.
After that I can distribute by making a public link, but since the updates, I can see my folders on the web, but if I enter a folder, then comes a SERVER error.
In my synced folder on the iMac, the files are marked with the green v whats means, the file is synced withe the cloud.
Our system is not overloaded, I hev tested it with other dropbox and other cloud sites.

ACS 4.0 and RSA Token Server problem

Hi,
We are having a problem trying to get ACS 4.0 for Windows to authenticate wireless users on an RSA Token server.
Our Cisco 1200 series AP is configured for WPA2 and LEAP authentication. It points at the ACS server for RADIUS authentication. Now this works fine for users with a static password defined on the ACS internal database. However, for obvious security reasons, we?d like the authentication passed to our internal RSA server.
I have installed the RSA Agent on the same server as the ACS along (after adding the generated sdconf.rec file to the System32 folder). The RSA server has been added to the ACS external databases and a user configured to use the RSA Token server for password.
When we try to authenticate, the ACS fails the attempt with reason ?External DB password invalid?. The same user can successfully authenticate when using the RSA test authentication tool which is installed on the ACS server as part of the RSA Agent software.
After running some debugs on a PIX in front of the servers, I can see traffic to/from the servers when using the test tool (which works), however it looks like ACS doesn?t even send traffic to the RSA server when authenticating.
Any help or advice appreciated.
Thanks

Hi,
The token servers only support PAP. Please make sure that the request are going to the RSA in PAP.
Following link talks about the same.
http://www.cisco.com/univercd/cc/td/doc/product/access/acs_soft/csacs4nt/acs40/user/o.htm#wp824733
Regards,
~JG

Cisco Network Assistant and add to comunity problem via HTTPS

hello,
i have big network of cisco switches and all is in my cisco network assistant in comunity connected via HTTPS. if i add new switch to network (all for HTTPS access is configured good: domain name, ip http secure-server, authenticate locale ...) and if i can add this switch to comunity (right click on icon and ADD TO COMUNITY), CNA say "Unable to Connect", because it can connect to switch via HTTP (i have disable it on switch), not via HTTPS. i have never version of CNA ... where is problem? why it not connect to switch via HTTPS? hmmm? thank you ... Peter

"The HTTP server interface must be enabled to display the network assistant. " Source.
You can put an access-list on the http server if you are concerned about security exposure.

Safari 3.x (Leopard) and Web Proxy Server Problems:

I have a Squid proxy server running on Linux. Users web traffic is directed through it via WPAD server which hosts a simple PAC file. The PAC files is very clean and small. It basically points all external (Internet) web traffic to our Proxy server. All of our Windows, Linux and Tiger clients work fine. However, Leopard (Safari 3.x) doesn't work quite right. Here's what happens:
Mac user logs into a Leopard 10.5 Mac. User launches Safari and tries to go to an external (Internet) site. The WPAD server is contacted and the Mac User is prompted to authenticate to the Proxy server. This is totally normal behavior thus far. Then, however, every few minutes the Leopard Mac user will be prompted to authenticate again (sometimes 2 or 3 times in a row!). Firefox 2.0.x, when configured to use the WPAD/PAC server and Proxy server, works fine in Leopard. Only Safari 3 in Leopard is having the problem.
All the Macs (Tiger and Leopard) are configured to use the Proxy server via OS X's Network Pref Pane (using the "Automatic Proxy Configuaration"). Reminder: Tiger works fine (even with the Safari betas), but Leopard's doesnt not.
I have attached our PAC file inline below (some things edited for privacy):
// SIMR automatic configuration for Mozilla and friends
// $Id: wpad.dat,v 1.8 2005/12/14 20:18:23 dct Exp $
// Edit carefully, since many may be relying on this...
function FindProxyForURL(url, host) {
// Bypass the proxy for internal addresses
if (!url.match("http:")
|| url.match("http://127.0.")
|| url.match("http://10.")
|| url.match("http://192.168.")
|| isPlainHostName(host)
return "DIRECT";
// These are exceptions given in the IE config for Windows.
if (host == "www.ncbi.nlm.nih.gov"
|| host == "chabry.caltech.edu"
|| host == "flybase.bio.indiana.edu"
|| host == "www.fedex.com"
|| host == "domain.org"
return "DIRECT";
return "PROXY <proxy server>:8080";
}

I think I have a similar problem. I am a Mac connecting to an otherwise all PC school network.
A new location with all correct proxies has been set up. However, Safari always crashes on first attempt to negotiate its way through our server to the internet. Internet explorer gets through because in its preferences it is possible to include the name of the school domain as well as my user name and password.
We have been unable to find any way of including the domain name into Location in Network or into Safari.
However, once Internet Explorer has negotiated with the server I can launch Safari and it works as normal.
Safari/Network seems to lack this option of including a domain name that my PC server requires.
Make sense to anyone?
Worth mentioning that my copy of Internet Explorer (5.2) often crashes, but usually it has done its job by then. I quite like the concept of Internet Explorer sacrificing itself to clear a path for Safari.

Netbeans and Windows 2000 Server Problems

I've tried to run netbeans on my windows 2000 server OS a few times. It usually doesn't work out and I have to go back to pcGrasp.
Does anyone out there know of any issues between netbeans and this OS. Is it worth it. I'd like to move away from the .net world and learn j2EE but I'd like to move up my IDE. Netbeans seems like the best choice. Does any experienced individuals out there know of a better one?
This was my latest error with netbeans. From just opening a folder??? I also tried to report it - I still have to wait another hour after I registered before I could HOPEFULLY find where exactly I can report it. Maybe thats why there are so many bugs. They make it impossible to report something they tell you to report to help out.
A java.lang.reflect.InvocationTargetException exception has occurred.
Please report this at http://www.netbeans.org/issues.html,
including a copy of your ide.log file as an attachment.
The ide.log file is located in your C:\Documents and Settings\Administrator\.netbeans\3.6\system folder.
Thanks for anything
-Wiley

I use Windows 2000 Professional and have not problems.
I would suggest,
- ensure you have all windows updates.
- ensure you have JDK 1.4.2_04
- try eclipse which is also free (From IBM) http://www.eclipse.org/

Mail and Microsoft exchange server problems

My company is moving to Microsoft exchange servers now, and for some reason, Mail cannot work.
There are several settings that are possible to set in Thunderbird, but that are not even options in Mail. These are settings such as "TLS".
Is there any way to make the same settings in mail that are possible in Thunderbird?

Hi Budgie
I can confirm that provided your administrator configures the Exchange server for IMAP (Mail uses IMAP to connect) that yes, Mail can be used effectively with Exchange and messages will remain on the server; though the set up can be misleading.
For me at least, when you get to Outgoing Server Settings, the set-up panel does not allow you to enter an authentication type, and entering my user name and password will get the following response:
The SMTP server “xxxxx.xxxxxxxxxxxxxxxxxxx.com:username” is not responding. Check your network connection and that you entered the correct information in the “Outgoing Mail Server” field. If it still doesn’t respond, the server might be temporarily unavailable.
If you continue, you may not be able to send any mail.
When I click continue, the authentication panel comes up, and by changing authentication to NTLM and entering the Domain name - everything works perfectly!
The only other nuisance is that Mail looks at the Exchange Calendar and Personal Folders/Contacts folders as mail folders, but cannot display the contents in the way Outlook or Entourage does, and I have not found a way of eliminating them from the folder list.
I hope this helps.

AAA and Cisco MDS switches.........

have configured Cisco ACS 4.0 (TACACS) with Windows AD for all Cisco MDS switches and it is working fine. But local "admin" access to the Cisco MDS switches via telnet is not working. At the same time , if I create a user with "network-admin" role locally, that works but not the default admin user.
Could anyone help me in this regard.

local. Below is the script I used to configure TACACS (Cisco ACS 4.0) on Cisco MDS switches.
config t
# Enable TACACS+
tacacs+ enable
tacacs-server host nnn.nnn.nnn.nnn key 0 xxxxxx
tacacs-server host mmm.mmm.mmm.mmm key 0 xxxxx
# Specify TACACS+ Server groups
aaa group server tacacs+ tacgrp
server nnn.nnn.nnn.nnn
server mmm.mmm.mmm.mmm
aaa authentication login default group tacgrp
aaa authentication login console local
# Enable TACACS+ Accounting
aaa accounting default group tacgrp local
end
copy running-config startup-config
Thanks
MOhan

AAA for Cisco MDS Switches

I have configured Cisco ACS 4.0 (TACACS) with Windows AD for all Cisco MDS switches and it is working fine. But local "admin" access to the Cisco MDS switches via telnet is not working. At the same time , if I create a user with "network-admin" role locally, that works but not the default admin user.
Could anyone help me in this regard.

You have two options.
1. Configure an "admin" user in AD. (note that you don't have to use the account named admin, you can just as easily assign a local user with the network-admin role).One thing to note, is that you normally use this local account in case the tacacs+ or radius authentication server goes down.
You can have users configured locally and AD at the same time. If you are running AAA the default config is to check your AAA servers first, if they are not available, then to default to a local account
2. Configure your local network-admin role user and then specify that say console access is authenticated locally, while ssh and telnet is authenticated through tacacs. This will allow you to always get in with a local account through the console, while it will force SSH and Telnet connections to authenticate through the AAA servers.
You can find this option in Device Manager > Security > AAA > Applications
If you found this helpful, please give it a rating.

Firmware info for MDS 9509

Requesting latest firmware info for Cisco MDS 9509 switches.

Hello,
The following link will take you to the download section for MDS Firmware:
http://www.cisco.com/kobayashi/sw-center/sw-stornet.shtml
You would need to login using CCO username/password.
Hope this helps.
Regards,
Nikhil

Interop problem between brocade 300d/200e and MDS 9509

Hi, I want to know if mds 9509 can interop with the SAN equipment below.
If yes, can you help me to configure (VSAN and type of ports - TE or T or F).
I tried with the interop VSAN 1 and 3, but there is still no communication.
MDS 9509
kickstart: version 5.2(2d)
system: version 5.2(2d)
and
Brocade 200E or 300D
V6.1.0J

You want Cisco MDS to be the principal switch, this is all explained in the FC standards.
The switch with the lowest wwn becomes the principal switch if the domain priorities set the same.
It is all explained in MDS config guide:
http://www.cisco.com/en/US/products/ps5989/products_configuration_guide_chapter09186a0080664c6a.html
http://www.cisco.com/en/US/products/ps5989/products_configuration_guide_chapter09186a0080664cd1.html#wp1185238

Span blade server on Cisco 3020?

I have an HP blade center with a Cisco 3020. From what I know, the baldes use a connection on the backplane for network connectivity. So my question is, can you setup a monitoring session to capture traffic from one individual blade server? I would normally span source interface destination interface. But how do I specify the blade server's interface when it's not on the switch itself? Thanks.

Hi Josh,
I'm not sure I really follow you here. The backplane of the blade server chassis is simply used as a communications channel between the blade server NICs and the server facing interfaces of the switch i.e., Gi0/1-16 and has no real bearing on how SPAN would work.
SPAN in the Catalyst 3020 switch works in exactly the same way as other Catalyst switches, with you specifying the source and destination interfaces etc., as you normally would. So assuming you have a server connected to Gi0/1 that you wanted to capture traffic to/from then you would configure something along the lines of monitor session 1 source interface gi0/1.
The tricky part can be the SPAN session destination and you have a number of options.
Use a server within the same chassis as the capture device.
If you have a server in the same chassis that has packet capture capability then you simply specify its NIC interface as the SPAN destination e.g., monitor session 1 destination interface gi0/2. The problem here is that when the destination interface goes into the monitoring state you'll lose in-band connectivity to the server so you would need to use the console to access the server.
Attach an external capture device to one of the switches external interfaces
The Catalyst 3020 has eight external facing interfaces i.e., Gi0/17-24 which are typically used for upstream network connectivity. If not all of these are in use then attach your capture device to one of those interfaces and configure the SPAN destination appropriately e.g., monitor session 1 destination interface Gi0/24.
Attach your capture device to an upstream switch and, on the Catalyst 3020, use an RSPAN VLAN as the destination to carry the traffic
This requires you define an RSPAN VLAN on the Catalyst 3020 and configure this as the SPAN destination. This VLAN is then configured on the external interfaces between your Catalyst 3020 and the upstream switch, where you would connect your capture device. In this case the upstream switch obviously requires a SPAN session to be configured as well.
There's discussion on the use of SPAN and RSPAN in the Integrating the Cisco Catalyst Blade Switch 3020 for the HP c-Class BladeSystem into the Cisco Data Center Network Architecture design guide that would go into more detail and has examples configurations.
Regards

Problem with Cisco 861W router and outgoing VPN

We have a Cisco 861W router that is blocking an outgoing PPTP on the internal access point only. The outgoing VPN works when the traffic is through a wired connection or the connection is on another access point. We fail to make a connection only when connection to the 861W's internal Access Point.
Here is the Access Point Configuration:
Current configuration : 2100 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname obap
enable secret 5 $1$.1RF$go1D7WITXUn3s8TUaw3tC.
no aaa new-model
dot11 syslog
dot11 ssid OLIVER
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 0 XXXXXXXXXXX
username XXXXXX privilege 15 secret 5 $1$Wc0K$OzcQDDQfjHP6La31eXMoG/
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm tkip
ssid OLIVER
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecti
ng AP with the host router
no ip address
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.0.2 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
banner login ^CC
% Password change notice.
Default username/password setup on AP is cisco/cisco with priv¾ilege level 15.
It is strongly suggested that you create a new username with privilege level
15 using the following command for console security.
username <myuser> privilege 15 secret 0 <mypassword>
no username cisco
Replace <myuser> and <mypassword> with the username and password you want to
use. After you change your username/password you can turn off this message
by configuring "no banner login" and "no banner exec" in privileged mode.
^C
line con 0
privilege level 15
login local
no activation-character
line vty 0 4
login local
cns dhcp
end
obap#
Here is the Router's Configuration:
Current configuration : 5908 bytes
! No configuration change since last restart
version 15.0
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname obrouter
boot-start-marker
boot-end-marker
logging buffered 51200
logging console critical
enable secret 5 $1$i9XE$DjxFVAEC9nC4/r6EQKCd6/
no aaa new-model
memory-size iomem 10
clock timezone PCTime -5
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
crypto pki trustpoint TP-self-signed-1856757619
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1856757619
revocation-check none
rsakeypair TP-self-signed-1856757619
crypto pki certificate chain TP-self-signed-1856757619
certificate self-signed 01
3082024D 308201B6 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31383536 37353736 3139301E 170D3036 30313032 31323030
34345A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 38353637
35373631 3930819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100B1A4 FB786547 3D582260 03DB768D 116BDE9A 309FBA04 B53F77B0 BFE32344
7C3439B3 97192B36 760A9411 1D5C7549 8D86F532 ABA44F53 0D08B7F4 A9A747D5
071330C3 65BF25A8 927F3596 29BB5A80 90C8D169 22268476 3B8DDE1E FDB7170D
B4820D03 5580A849 A92C7E76 9AC10867 505A2FEE 64360741 7F9DBDBF 3D79982C
F81D0203 010001A3 75307330 0F060355 1D130101 FF040530 030101FF 30200603
551D1104 19301782 156F6272 6F757465 722E6272 75736868 6F672E63 6F6D301F
0603551D 23041830 168014D8 5BC2FFB2 967A4C7B 11B44122 5C8D31F7 749B9230
1D060355 1D0E0416 0414D85B C2FFB296 7A4C7B11 B441225C 8D31F774 9B92300D
06092A86 4886F70D 01010405 00038181 005901F1 C239074B B8213567 CF7B65BF
DAFE4557 69B2A3B1 5F2593C7 A54B9598 23FD5E7A 563AA6E0 AFB25801 FA0061E8
F9545372 DB600B3A BE68AE65 1EDA593E 6A0C96B8 5A4136AF 393F9AAC 651E1C36
B8B7C6C0 47936C24 D2ECE9A5 9446EE32 FC7461FA AD8CF1CE A7FBF341 07E9C3C6
505AB88D 0E7FCAFC 5792298A E5E4D1FE CC
        quit
no ip source-route
ip dhcp excluded-address 192.168.0.1 192.168.0.99
ip dhcp pool ccp-pool1
   import all
   network 192.168.0.0 255.255.255.0
   dns-server 216.49.160.10 216.49.160.66
   default-router 192.168.0.1
ip cef
no ip bootp server
ip domain name brushhog.com
ip name-server 216.49.160.10
ip name-server 216.49.160.66
license udi pid CISCO861W-GN-A-K9 sn FTX155281FY
username tech38 privilege 15 secret 5 $1$d/4Z$n/23EsXbzfHF5XfJ8Nv.y0
ip tcp synwait-time 10
ip ssh time-out 60
ip ssh authentication-retries 2
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface FastEthernet4
description $ES_WAN$$FW_OUTSIDE$
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
duplex auto
speed auto
pppoe-client dial-pool-number 1
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered Vlan1
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
arp timeout 0
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$$FW_INSIDE$
ip address 192.168.0.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1412
interface Dialer0
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1452
ip flow ingress
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname XXXXXXXXXXXXX
ppp chap password 7 XXXXXXXXXXXXXXXX
ppp pap sent-username XXXXXXXXXXXXXX password 7 XXXXXXXXXXX
no cdp enable
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source static tcp 192.168.0.25 80 interface Dialer0 80
ip nat inside source list 1 interface Dialer0 overload
ip route 0.0.0.0 0.0.0.0 Dialer0
logging trap debugging
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 192.168.0.0 0.0.0.255
dialer-list 1 protocol ip permit
no cdp run
control-plane
banner exec ^C
% Password expiration warning.
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username <myuser> privilege 15 secret 0 <mypassword>
Replace <myuser> and <mypassword> with the username and password you
want to use.
^C
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
line con 0
login local
no modem enable
transport output telnet
line aux 0
login local
transport output telnet
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
privilege level 15
login local
transport input telnet ssh
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
end
Any help would be appreciated

Hello,
i have the same problem with router CISCO861W-GN-E-K9. Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
Can someone help?
Thank you.
Here is my config for internal AP and router.

Cisco MDS 9509 and HP Blade server problem

Similar Messages

Maybe you are looking for