Cisco Mobile 8.0 iphone: How to configure the Directory? is it the same on the IP phones?

Hi,
I have a few iphones running Mobile 8.0 and Mobile 8.1. Everything works fine except for the Directory.
Im looking to get the the directory working on the Mobile 8.x phones; the Coorporate Directory (the same as in the IP Phones) is this possible on the Cisco Mobile 8.X?
If so, how to get it to work?
I've read about setting up LDAP for the Mobile 8.x phones; is this what's needed or is this to access my MS Active Directoy data from my business side?
Im running UCCM 7.x and on my IP phones I have an option 5 for Coorporate Directory, I want this on my Mobile 8.x phones.
thanks

Your organisation's Active Directory is what I'm referring to (or most other LDAP directories if you're not using AD, although they're not all supported). You would indeed need to populate your Active Directory with the user's extension numbers for this to be of any use to you.
We do indeed use the directory on Cisco Mobile, but because we already have all End Users in our Communications Manager imported via LDAP, we're not maintaining two directories, the number that the End User is allocated comes from our LDAP database.
If all your phone users are manually created then you are going to have a bit of extra administration burden to provide the directory to Cisco Mobile users.

Similar Messages

I have just switched to samsung and i have removed the sim from the iphone however i am still receiving texts rather 'imessage' on the old iphone. how do i make sure all messages only come to my new phone??

i have just switched to samsung and i have removed the sim from the iphone however i am still receiving texts rather 'imessage' on the old iphone. how do i make sure all messages only come to my new phone??

You can turn iMessage off on your iPhone. That's relatively easy. Since iMessage is an Apple product/service, I have no idea how a Samsung phone will deal with an incoming one. For that answer you should probably contact Samsung support.

HT201210 my friend connected my iphone to his laptop and now his apple ID is on my iphone- how do I change it back to my apple ID on my phone so that I can purchase from itunes again?

my friend connected my iphone to his laptop and now his apple ID is on my iphone- how do I change it back to my apple ID on my phone so that I can purchase from itunes again?
thanks.

Restore your phone using the last backup that you made. That should put everything back the way it was.

I have a Symphonic 32' HDTV (Dolby Digital Plus). can someone help me figure out how to configure it optimally with my Mac Mini? the display and sound is off. Do I need drivers/software? I'm new to macs.

I have a Symphonic 32' HDTV (Dolby Digital Plus). can someone help me figure out how to configure it optimally with my Mac Mini? the display and sound is off. Do I need drivers/software? I'm new to macs.

Hello, since nobdy else has replied...
Long shot, but...
Open Audio Midi Setup in Applications>Utilities, see the input & output options & KHz setting there.

When i use imessage on my ipnone 4 it comes up as my email on my wifes iphone. how do i fix this to where it shows up as my phone number?

when i use imessage on my ipnone 4 it comes up as my email on my wifes iphone. how do i fix this to where it shows up as my phone number?

Had the same problem and trying to remember how I fixed it. Let's see...
Try this:
1) Settings > Messages > Receive At > Use your Apple ID for iMessage > make sure you are logged out from Apple / iTunes.
2) under "You can be reached for messages at:" > make sure only your phone number shows and no email address.
Hope that works, if not I just can't remember what else I did. However I got it working so that my tel number now shows to iMessage recipients instead of my email address.

How to configure a plugged in usb device to use the winusb driver

Hi,
We have an app that uses an ANT+ USB dongle to tap into ANT+ messaging traffic and we would like to get our app up and running on the Raspberry PI running Windows 10 IoT.
Using Powershell I can see that the device is recognized when plugged in:
Name                           Property
126                            DeviceDesc          : ANT USB-m Stick
                               LocationInformation : Port_#0005.Hub_#0002
                               Capabilities        : 20
                               ContainerID         : {207a56e2-9393-5c49-bdd7-309b37712562}
                               HardwareID          : {USB\VID_0FCF&PID_1009&REV_0100,
USB\VID_0FCF&PID_1009}
                               CompatibleIDs       : {USB\Class_FF&SubClass_00&Prot_00,
USB\Class_FF&SubClass_00, USB\Class_FF}
                               ConfigFlags         : 64
I would now like to configure it to use the already available WinUSB driver so that we can 'talk' to it from c#. Is there any way I can do that like e.g. provide and .Inf file, but then, how do install that from powershell? On a regular windows device we
would be able to switch the drivers through the device manager or so but how to go about it on Windows 10 IoT?

What you might need to do is compare how this device is configured for use on your desktop system, and then duplicate those registry entries on your Pi device so it will attempt to use the WinUSB driver when detected.
This article talks about using remote powershell to modify the registry on a remote device:
http://blogs.technet.com/b/heyscriptingguy/archive/2012/03/16/use-powershell-to-edit-the-registry-on-remote-computers.aspx
If that doesn't work or you still have problems can you please provide a screen shot of the following information:
In DeviceManager->Right click the device->Properties->Driver->DriverDetails.
Jonathan Tanner | Microsoft | Windows 10 IoT Core Insider Preview Support | This posting is provided 'as is' with no warranties and confers no rights.

HT1212 forgot my passcode on my iphone. how can i get passed it so i can reset the password?

forgot my passcode on my iphone. how can i get passed it so i can reset my password?

You can try and restore it from the computer to which you've previously synched. If this does not work, you'll have to force your phone into recovery mode and restore as a new device. All your data will be wiped.

How to configure Output Directory at Jobs

Allo.
I am quite new in IR eventhough I played with FR for months already.
I need to set a BQY job to run every morning and inside the job has multicycle things. One of it is to export the processed BQY into my drive D:\\InterativeReporting\. Now, I manage to go through until the job parameter -> modify cycle -> process option and the last page shows me to use Output Directory.
From the docs I know that this Output Directory need to be configure manually but it's not written in any docs!
So, I had done;
1. checked the documentation of HBI (hs_user.pdf, hs_admin.pdf)
2. checked IR users docs
3. Checked FR & Prod Reporting docs
4. hoping it will work like FR with it's external directory where we need to change a bit at the scheduler.properties and go through all .properties under BIPlus/Lib/
5. sacrifice my fried chicken lunch to nearby kitten
Does anybody knows how to configure the output directory? Please let me know. I can't afford to keep sacrificing my lunch..
Thanks!
Daniel.

Hi Guys,
Yeah, I found it at the Developer Guide and follow the direction there. Spent entire morning to try it and it works!
However, it should have been faster using the Physical Resources feature available at Workspace! But I got good lessons there with java -after numerous hair pulling experience and all zoo words shouting. LOL.
I got to bounce to Singapore last week and I left my laptop at my apartment, sorry for late reply and thanks guys!
Daniel.

How i configure external directory and email

hi every one
i have just installed and login to oracle beekeeper successfully. now i want to intergate the external directory to my active directory so that all users in it will be mapped in oracle beehive secondly i can use them for email purpose.
i am really new to oracle beehive , i have read the administration manuals. but still confusing how to start , the parameters in external directory creation for active directory cannot understandable for me, what does authectic attributes means.
kindly guide me in this regard and secondly if any image base document avaible so that i configure it through that.
regards
Oraclebeehive new user

Hello,
The primary Authentication Attribute, is just the LDAP attribute you will use to be able to log on Beehive
That can be an UID, the email address, the cn or with AD the sAMAccount
eg: uid: 123455667
mail: [email protected]
cn: firstname.lastname
these attributes and their associated values are on AD and must be available for ALL employees as well as UNIQUE.
Often the email address, the UID or the sAMAccount have unique value.
Hope that help
However, You may want to take some days of expertise to help you on this setting. That will simplify and speed up your learning curve and Beehive implementation.
Regards,
Fred

How to configure queues for sending IDOCs from XI in the same order receive

Hi,
We are collecting IDOCs and sending them to XI using a background job (RSEOUT00) from R/3. When XI receiving these collected IDOCs, it's forwarding the received IDOCs into different queues for processing them and sending them to receiver system. Some times some queues are taking longer time to process the received IDOC and in the mean time the latest IDOC received getting processed and sent to receiver system. When the information related to this old IDOC is sent out to receiver system after the latest IDOC information is sent to due to delay in Queue processing, we are getting errors in the receiver system. Can somebody explain the steps to configure queues to process the IDOCs in the same order they received from R/3.

Hi,
Why not tunnel all the IDOCs to one queue for processing ?
Cheers
Colin.

Cisco Mobile 8.0 IPhone register question

Hi:
i user mobile 8.0 in IPhone , when loacl Lan register to CUCM(6.1.5) is very nice , but via Wi-Fi(different subnet) or Remote Wi-Fi or 3G(use VPN) can not register to CUCM and IPhone show Disconnected
Thanks

I am seeing the same problem. I am trying to setup the iPhone for the first time so I though it was something I was doing.
Opened a case with TAC. He could not find a record of the iPhone IP hitting the server so he said the communication was not getting through.
However on the iPhone:
-if I put in the device ID of a CUPC device it would report back "Protocol not supported"
-if I put in an invalid device ID it would report back "configuration not found"
-if I put in the iPhone device ID it would wait 30 seconds and report back "Verification timed out"
Based it on this it is obviously communicating with the CM server but something is interrupting it from finishing.
I have not tested via the LAN yet but that is my next step.

Cisco Mobile 8.1 iPhone

Hi,
I´m missing a couple of files to test the app out on a asterisk server.
Could anyone provide me with a sample file of AppDialRules.xml and DirLookupDialRules.xml. Can anyone provide these two files?
Thanks,
Eivind

Jonathan,
The problem is that I don´t have a UCM
So if you or anyone else could provide these files so that I can test it on a Asterisk solution, that would be great
Thanks,
Eivind

How does Configurator's directory structure work? Can database/devices be recognized once they're "lost"?

Yes this is as bad as it sounds. Configurator started freezing and crashing today. It asked to be reinstalled after "Core Data" errors. I went to a back-up and started overwriting the existing directories, but nothing seems to work. I've copied about 200 resource files into every resource directory I can find, but each time I open Configurator, it doesn't see the 230+ devices it has configured.
Does anyone have any advice on how to do this? Is there some file that can be deleted and rebuilt? There's so much I fail to understand about this software.
And make sure everyone backs things up more often than I do.
Thanks!

Yes this is as bad as it sounds. Configurator started freezing and crashing today. It asked to be reinstalled after "Core Data" errors. I went to a back-up and started overwriting the existing directories, but nothing seems to work. I've copied about 200 resource files into every resource directory I can find, but each time I open Configurator, it doesn't see the 230+ devices it has configured.
Does anyone have any advice on how to do this? Is there some file that can be deleted and rebuilt? There's so much I fail to understand about this software.
And make sure everyone backs things up more often than I do.
Thanks!

How to configure Open Directory base DN

Hi,
I have been using OpenLDAP on a Synology NAS drive, but this has some serious shortcomings with Mac clients (eg. roaming profiles simply doesn't work).
So I have bought a MacMini which among other things will replace my existing LDAP server with Open Directory.
As a dry run, I enabled the Open Directory and went through the simple set up and I had a basic system up in no time. However I have come up against an annoying issue with the base DN used by Open Directory and I hope someone will be able to help me.
My existing LDAP has a base DN that looks like this: dc=myorg, dc=local
So when users log in, they can use a username which conforms to the following format: [email protected]
The problem is that Open Directory likes to set the base DN to: dc=macservername, dc=myorg, dc=local
meaning that a fully qualified user account name now becomes: [email protected]
This seems bonkers to me. For example, what would happen if I introduce a second Mac server into the mix and failover to it - the servername element of the DN becomes redundant or if it changes, I need to communicate with all users.
I must be missing something obvious - but there doesn't seem to be much in the way of configuration that I can see through the Server application.
So, my question is, how can I configure my base dn without the servername so that my existing username context remains the same?
Many thanks - I look forward to any responses.

I agree with Dal78 Apple using a base DN of servername.example.com rather than just example.com is illogical. In fact originally they did seem to use just example.com as the format but in recent years now use server.example.com as the format. When I first encountered this change it was still possible to overridge the use of servername.example.com and force it to use just example.com as the format. In more recent times I have decided to leave things the way Apple do it.
I don't know if there is an official answer as to why, but a possible guess is that you can now have multiple Open Directory servers for a single domain. This is the 'Locales' option in Server.app. It maybe that including the servername makes it possible/easier to implement this.
I also agree Strontium90 do not use a .local root domain for Open Directory. In theory there are hacks to (sort of) get this to work, but Apple engineers will typically run screaming for the woods when they encounter this.
PS. Briefly Apple also did the same illogical thing with DNS zones, whereby the zone name for a domain was servername.example.com instead of example.com this at least they have stopped doing.

I lost my iphone, how can i back it up without it then erase the data

i did not have the chance to click on icloud and hit sync manually or automatically, when i click on find my phone it says the device is offline. i would like to get a new phone but i would like to know how to sync the data from my phone to my compute then erase it from my phone completely incase someone picks it up. it is probably ruined because it has rained the past 2 days.
please help if you can thank you !!

Contact your carrier and the police. If it was lost in a specific building, ask the people running it.
(124410)

Cisco Mobile 8.0 iphone: How to configure the Directory? is it the same on the IP phones?

Similar Messages

Maybe you are looking for