Cisco module controller & 1131 access-point

I'm using a blade as a controller in a cisco router. trouble is it does not see
the 1131 access-points. does see 1020 access points. Any thoughts

If you are using OP 43 to tell the access points where to find the controllers you will need a new entry for the 1130 series of access points.

Similar Messages

Cisco Outdoor Controller Based Access Point

Hi,
I am looking for Cisco Outdoor Controller Based access point model. The WLC is Cisco 2500 Series.
I have checked couple of outdoor models but all are mesh access point. I am looking for normal controller based outdoor access point ( just like controller based indoor access point models )
Thanks.

adding to Leo...
Cisco Aironet 1300 Series
http://www.cisco.com/en/US/products/ps5861/index.html
Cisco Aironet 1550 Series
http://www.cisco.com/en/US/products/ps11451/index.html
Cisco Aironet 1520 Series
http://www.cisco.com/en/US/products/ps8368/index.html
these all are Cisco OUTdoor APs.
Now u can choose as per ur req.
Regards
Dont forget to rate helpful posts

1131 ACCESS POINTS BOUNCING

I have a site with Lightweight 1131 access points, with 5508 WLC's in HA running Code 7.4.110. In 2 areas of one site the access points are bouncing, I have attached the logs from one of the AP's at the site. The switch that the AP's are connected to is a WS-C3750-24P SW VERSION: 12.2(55)SE1. This has only happened in 2 areas on the site, and only 24 Access Points out of 335. HELP!!!!!!

Hi Scott
I have 184.2 Watts remaining on the switch. I have just come back from site having tried the following:
1. Took and AP from another site, this worked.
2. Bounced the Access Points to a controller still running 7.3.101.0 this also worked.
3. Bounced the Ap's back to their local controller, they went back to not functioning correctly.
We upgraded to Code 7.4.110 it was an,assured, tested version from Cisco, to fix other issues we had. Any help would be welcome.

PoE for Cisco 1242AG and 1310G Access Points

Dear All,
we purchased a Cisco 1242AG and a 1310G Access Point and in the DataSheet it was specified that these APs support Power-over-Ethernet. The problem is we don't see any RJ-45 port in either AP which could be used for connecting the AP to an PoE Switch. Can you please tell us how we can connect these APs to an 802.11af compatible PowerBridge (by Intermec) ? Thanks.

Hi Thorsten,
The 1242 should be good to go but the 1310 is powered quite differently. Have a look;
AP 1240 Series - Hardware (see diagram)
http://www.cisco.com/en/US/products/ps6521/products_installation_guide_chapter09186a008079b7f4.html#wp1071972
Connecting the Ethernet and Power Cables
http://www.cisco.com/en/US/products/ps6521/products_installation_guide_chapter09186a008079b7f4.html#wp1052781
1300 Series Power
Power
The access point/bridge receives inline power from the Cisco Aironet Power Injector (hereafter called the power injector). Dual-coax cables are used to provide Ethernet data and power from the power injector to the access point/bridge. The power injector is an external unit designed for operation in a sheltered environment, such as inside a building or vehicle. The power injector also functions as an Ethernet repeater by connecting to a Category 5 LAN backbone and using the dual-coax cable interface to the access point/bridge.
The power injector is available in two models:
Cisco Aironet Power Injector LR2 standard version (included with the access point/bridge)
48-VDC input power
Uses the 48-VDC power module (included with the access point/bridge)
Cisco Aironet Power Injector LR2T optional transportation version
12- to 40-VDC input power
Note The power injector and the power module must not be placed in an outdoor unprotected environment. The power module must not be placed in a building's environmental air space, such as above a suspended ceiling.
http://www.cisco.com/en/US/products/ps5861/products_installation_guide_chapter09186a008079b93b.html#wp1051840
Dual coaxial cable to run from the power injector to the 1300. See attached notes:
Cisco Aironet 1300 Series
Cisco Aironet 1300 Series Access Point/Bridge Power Injector
The Cisco Aironet 1300 Series Outdoor Access Point/Bridge Power Injector,converts the standard 10/100 BaseT Ethernet interface that is suitable for weather protected areas to a dual F-Type connector interface for coax cables that are more suitable for harsh outdoor environments. The Power Injector also provides power to the outdoor unit over the same cables with a power discover feature and surge protection. To support longer cable runs from your wireless network switch or router, the Power Injector LR is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters of indoor cat5 cable?enabling total cable runs up to 200 meters. The Cisco Aironet 1300 Series Outdoor Access Point/Bridge ships with the Power Injector LR2 and an AC power supply.
From this link:
http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a008022551d.html
Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide
Ethernet Ports
The access point/bridge dual-coax Ethernet ports consists of a pair of 75-ohm F-type connectors, linking the unit to your 100BASE-T Ethernet LAN through the power injector. The dual-coax cables are used to send and receive Ethernet data and to supply inline 48-VDC power from the power injector to the access point/bridge.
From this link:
http://www.cisco.com/en/US/products/ps5861/products_installation_guide_book09186a00804d3095.html
AIR-PWRINJ-BLR2
F-Type Connectors
Dual coaxial cable carries full-duplex Ethernet, DC power, and full-duplex console port (RS-232 connection)
From this link:
http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a00802252e1.html
Hope this helps!
Rob

Document on 1131 Access point

Please provide the documentation to configure 1131 Access Point.
We are getting documentation for 1130 and not for 1131.
Help wouldl be highly apprecited.

Hi Navinder,
It's the same. 1130 is the generic model number while 1131/1132 is a specific model number.

Cisco 802.11n Outdoor Access Point

I have to propose to a client a 802.11n outdoor Acess point with external antenna, tha gain must be >8 dbi.
Which cisco model should i use ?

I have to propose to a client a 802.11n outdoor Acess point with external antenna, tha gain must be >8 dbi.
DO NOT, under any circumstances, use 1260 or 3500e if you plan to use antennas > 6 dBi. These two models DO NOT SUPPORT antenna gain higher than 6 dBi. The only two 802.11n-capable WAP that can support high-gain antenna of > 6 dBi are the 1250 and the 3500p.
Antenna Product Portfolio for Cisco Aironet 802.11n Access Points
The 1250 is End-of-Sale (End-of-Sale Date: 12 January 2012) and requires 20.0w of PoE. The 1250 can support antenna gain > 6 dBi.
The 3500p was released around mid-2011 because people were howling/screaming about the lack of high-gain antenna support, thus the 3500p was developed alongside the AIR-ANT25137NP-R.
Cisco recommends that the installation of the AIR-ANT25137NP-R should be done with proper sight-survey.
[Sorry Scott. Didn't want to be rude. ]

1131 access point, broken flash?

I have had two 1131 access points die in the last few weeks, both with the same symptoms. I suspect both have broken flash systems and are due for the bin. If anyone can offer any confirmation or a way to fix it, I would be grateful.
On booting, it gives the following error:
Xmodem file system is available.
flashfs[0]: unable to allocate available block.
The system has been interrupted, or encountered an error
during initializion of the flash filesystem. The following
commands will initialize the flash filesystem, and finish
loading the operating system software:
    flash_init
    ether_init
    tftp_init
    boot
ap:
Trying to wake up the flash:
ap: flash_init
Initializing Flash...
flashfs[0]: unable to allocate available block.
...done Initializing Flash.
ap: dir flash
unable to stat flash/: permission denied
I have tried the standard recovery mode of uploading a new firmware via TFTP, but I can't even set variables:
ap: set IP_ADDR 10.0.0.1
flash:/env_vars.tmp: invalid argument
The filesystem containing the variables may not be initialized yet.

Thanks for the tip, however I should probably have said the access points are autonomous, so the method you suggested will not work.
Yes it does.
You need a two-step method.
Your AP is booting up with either no IOS or a corrupt IOS.
1. In order to efficiently transfer the IOS to an AP that has no IOS you need to use the process I've posted earlier.
2. Once the AP boots up in autonomous mode, it's as easy as giving the BVI1 an IP address and use the command "copy tftp: flash:" to transfer the LWAP/CAPWAP IOS to the AP.

Controller-based access points conversion

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin-top:0in;
mso-para-margin-right:0in;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0in;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
Q:
I’ve the 1140 AP (LAP) flavor; can I convert it to Standalone access points?
If yes can you please explain how and if you have documentation that will be great.
Thank you all for reading and helping.

You can convert the AP from autonomous AP (aAP) to light-weight AP (LWAP) and vice versa. It all boils down to the IOS you run.
If you have a WLC, ollow the proceedure below:
Using a Wireless LAN Controller to Return to a Previous Release
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp157689
If you don't have a WLC, follow the proceedure below:
Using a Wireless LAN Controller to Return to a Previous Release
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp157689
If you find my post helpful, please do not hesistate to rate. Thank you very much.

Configuration of cisco aironet 1260 series access point..??

i hv a cisco aironet 1262n access point and a normal router(without wlan) with a broadband connection
now i want to use my access point as a wifi hotspot
but i am not able to access it, through web browser
i dont know how i connect wires so that i am able to access " AP access page" and also i forgot its IP address too so can u pls tell me how do i reset it to default

Your AP is most likely loaded with a controller-based IOS. You can easily convert this to autonomous IOS.
Read this: Using a TFTP Server to Return to a Previous Release

Image Recovery for Cisco Aironet 1300 Outdoor Access Point

We purchased two 1300 APs for outside. There is a new release for the image that we wanted to use so, we have the latest security updates. We downloaded, logged onto the access point just fine, but the image never took. After four hours with a direct connection, it was still going and this morning we came in and it just keep rebooting. Our network guy states it looks like a corrupt image. We can barely do anything and since there is no "mode" button like the earlier models, I have not found anything on web sites or forums to help us reload a good image to the access point. I would appreciate any insight someone has and/or where to look for this. I logged on and downloaded about every manual on the 1300 I could find, but have not found a good way to fix this. Not even the upgrade tool will connect since it just keeps rebooting.

Hi Bruce,
Because (as you correctly noted) the 1300 does not have a mode button you could try this method;
Complete the steps in this section in order to reset Cisco IOS Software-based bridges:
If the privileged command prompt ap# is available in the CLI, the write erase command and the reload command erase the startup configuration and reset the unit.
If the GUI is available, choose System Software > System Configuration. Press the Reset to Defaults button.
Aironet 1300 Series Bridges do not have a MODE button to reset the AP to factory defaults. So, if neither the GUI or CLI is available with sufficient privileges, complete these steps to delete the current configuration and return the entire bridge settings to the factory defaults using the CLI.
Open the CLI with a Telnet session or a connection to the bridge console port.
Reboot the bridge by removing and reapplying power.
Allow the bridge to boot until the command prompt appears and the bridge begins to inflate the image.
Press ESC when you see lines that are similar to these on the CLI:
Loading "flash:/c1310-k9kw-7mx.v122_15_ja.200040314-k9w7-mx.v122_15_ja.20040314"
...#############################################################################Note: In order to access the boot loader, you must press ESC twice. But this action depends on the terminal-emulation software that you use.
Messages that are similar to these appear:
Error loading "flash:/c1310-k9kw-7mx.v122_15_ja.200040314-k9w7-mx.v122_15_
ja.20040314"
Interrupt within 5 seconds to abort boot process.
Boot process terminated.
The system is unable to boot automatically. The BOOT environment variable needs to
be set to a bootable image.
C1310 Boot Loader (C1310-BOOT-M), Version 12.2 [BLD-v122_15-ja_throttle.20040314 100]
bridge:At the bridge: prompt, issue the dir flash: command in order to view a directory of the Flash file system.
The directory is similar to this directory:
bridge: dir flash:
Directory of flash:/
2 -rwx 0 env_vars
5 drwx 384 C1310-k9w7-mx.v133_15_JA.20040314
3 -rwx 1128 config.txt
4 -rwx 5 private-config
3693568 bytes available (4047872 bytes used)
bridge:Delete or rename the files config.txt and env_vars, and reboot the bridge.
Note: Do not forget the / character before the filenames.
bridge: delete flash:config.txt
Are you sure you want to delete flash:/config.txt (y/n)?y
File "flash:/config.txt" deleted
bridge: delete flash:/env_vars
Are you sure you want to delete "flash:/env_vars" (y/n)?y
File "flash:/env_vars" deletedIssue the boot command in order to reboot the bridge at the bridge: prompt, or simply power cycle the bridge.
After the bridge reboots, reconfigure the bridge with the web browser interface, the Telnet interface, or Cisco IOS Software commands.
Note: The bridge is configured with the factory default values that include:
The IP address, which is set to receive an IP address with DHCP. If you do not have a DHCP server, you can access the bridge using the default IP address of 10.0.0.1 using HTTP/HTTPS or Telnet. Once you gain access to the bridge via Telnet or GUI, you can modify the IP address of the bridge.
Note: This default IP address of 10.0.0.1 becomes available only for a short period. So, make sure that you assign your own IP address to the bridge within that period of time.
The default username and password, "Cisco".
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_password_recovery09186a00800949d0.shtml#ca_1310_ser
One other thing, be careful with the new IOS that you aren't loading a LWAPP Recovery Image. (it almost sounds like what may have happened)
Hope this helps!
Rob

Cisco aironet 1310 Outdoor access point

I am looking at outdoor access points, I want to stick with Cisco aironet, we currently have 6 of them that are 6 years old and running great, one has had a problem because of humidity, dried it out and relocated and we are good again.
I was looking at the Aironet 1310 Outdoor access point, but I can't find much information on it. I am looking to see how many SSIDs can be setup, we currently have 2 one private, and one public, this is done with VLANS. I am also looking at finding out about the power injector, it converts to coaxial cable, it has 2 RJ-45 and 2 Coaxial, does this mean if we get 2 access points, then I only need 1 power injector?
Thanks for any help you can give.

Rusty:
AP supports up to 16 SSIDs to be configured.
Multiple SSIDs with VLANs configuration is done almost the same way you do with current Aironet APs.
see here: http://tiny.cc/0qwnkw
You also need one power injector per AP. Each AP should use it's own power injector.
The two coaxial output in the power injector both are used to be connected to the AP (see below image).
The RJ-45 connectors in the power injector one of them is for Console connectivity and the other for network ethernet connectivity.
Check here: http://tiny.cc/7gxnkw
HTH
Amjad
Rating useful replies is more useful than saying "Thank you"

Cisco 1131 access point status led

Hi
Any one experienced a white light on the status led, its the "ring light" infront of the AP. ive checked on http://www.cisco.com/en/US/docs/wireless/access_point/1130/installation/guide/113h_c4.html where all colours are listed and none point done to white.
ANy ideas?
Thanks

Here's an update on this issue. I have had about a 2% failure rate on my 3502i's due to blue, green, and white light freezing. We sent several unit to Cisco's wireless engineer team in Richfield. They have found the issue and have written a fix and are currently doing testing this weekend. They are sending a senior wireless engineer to my office on Monday morning to apply the fix on the 200 units that we have yet to deploy. This is the bad part: the fix can only be applied through the console port and they won't have this integrated into a controller code until May/June. The good news is they have a fix or will just RMA with no questions. I have a webex with their wireless team to explain exactly what the issue is, but from what I gathered is something to do with the boot loader image and the IBM chip in the unit. I will follow up with you guys on Mon/Tues.
Sent from Cisco Technical Support iPhone App

How to configure IP Address filter in Controller based Access Points ?

Dear Team,
Configuration:
i have 5508 series controller and joined the two Thin APs to the controller. WLAN controller is connected to PC where Multicast receiver is running for two Multicast IP addresses (IP1: 230.1.1.1, IP2: 230.1.1.2). Multicast sender is running for two IP addresses on Station.
Requirement:
When Station is associated to AP1, AP1 should block the multicast packets going to AP2 and vice versa . That is AP1 should be configured to block multicast packets going to 230.1.1.2 and AP2 should be configured to block multicast packets going to 230.1.1.1.
Thanks,
Harsha

I believe you could apply ACLs and check if that helps.
For more details about configuring ACLs, please refer to the following link:
http://www.cisco.com/c/en/us/td/docs/wireless/controller/8-0/configuration-guide/b_cg80/b_cg80_chapter_0110101.html#task_AA3AFA57D51647478E0C3511137C165E
Hope that helps.

Cisco Aironet 1240 AG Access Point - configure Mac Address using Telnet

Hi there,
IÂve got a problem hopefully someone can help me with. I have the above mentioned AP and it is configured, working well and providing wireless access to several laptops on our domain.
The thing is I canÂt get access to the web-based interface to add new laptops Mac addresses to the AP as I currently have them secured with local list Mac address authentication but my user name and password when entered in the web browser login dialog box wonÂt allow me in although strangely it does allow me to login using the same credentials when I telnet into the AP.
Does anyone know why I canÂt get logged in using the web interface even though the user name and password does appear to be correct as I can telnet in? Also if you have any suggestions how I could sort this without having to perform the password recovery procedure, as I donÂt want all the config on the AP wiped and want to avoid having the set the whole thing up again.
As I workaround if anyone knows what the commands are to allow me to add the Mac addresses of the new laptops so they are added to the local list Mac address authentication list so the new laptops are secured that would be great.
Thanks in anticipation,
Tony

Your AP is probably configured to use the enable secret as the password. Try entering nothing for the username, and enter your enable secret for the password ('Cisco' by default).
If that doesn't work, post your running-config and we'll be able to see why it's doing that. It's a standard configuration, and no worries because wiping the AP won't be necessary since you can successfully Telnet in.
Jeff

Cisco aironet 1200 Series access point dropping clients

We are having an issue where our Cisco Aironet 1220 Series AP is constantly dropping clients. We have 3 APs mounted on a single tower, all out of each others range and freq. There are approximatly 30 clients on each AP. We are noticing an increase in dropped customers (up to 20 at a time). ANy suggestions? This only became an issue in the last few weeks, and nothing major has changed.

Hi
Even I was facing almost the same kind of problem. But in my case it was wired clients to the workgroup bridge 350.
I had done lot of testings and reading at that time to resolve this problem.
However in your case I feel your problem can be resolved by keeping the option "Reliable multicast for Workgroup bridges" disabled in the APs under dot11radio interface settings. This is possibly because the radios cannot associate to more than 20 clients at a time if the option is in the enable mode.
You need to keep this option enabled in a root bridge when you have problems of dropping the wired clients to the workgroup bridge.
By keeping this option enabled, you are actually asking the Root bridges to consider the Workgroup bridges as Infrastructure devices and not as clients thereby making the roots to send all the multicasts to the WGBs. However in that case it losses the efficiency of associating more than 20 clients.
Let me know if this resolves your problem.
Regards

Cisco module controller & 1131 access-point

Similar Messages

Maybe you are looking for