Cisco MSE CMX dashboard

Hi,
I have some problem with CMX dashboard configuration, I followed the configuration guide (http://www.cisco.com/c/en/us/td/docs/wireless/mse/7-6/CMX_Dashboard/Guide/Cisco_CMX_Dashboard_Config_Guide.html) and can't understand, how do I add a map to CMX dashboard to define points of interest, all I can see is only gray screen with button "Update Floors Maps" and when I press it - nothing happens. However CMX analytic works just fine, and maps fully syncronized with cisco Prime

"The maps and location data for the campus, building, or floor are uploaded to the Prime Infrastructure and synchronized with the Location MSE. The CMX Dashboard displays these maps."
Well, it doesn't, I don't see any maps which I created in cisco Prime and syncronized with MSE
"Click the white triangular icon in the right pane located at the left side of System Campus."
There is no System Campus when I click on white triangle

Similar Messages

Cisco MSE CMX problem

hi all,
When I tried to configure CMX on my MSE after adding the license i follow these steps:
Choose Mobile Concierge Service > CMX Dashboard Configuration.Choose the Location MSE that the CMX Dashboard MSE gets the maps and location data from. It can be the same MSE or a different MSE.
after I open Mobile Concierge Service I found that CMX Dashboard Configuration not appeared
kindly find attached screenshot from my MSE.
please advice
thanks in advance

Hi csco12050227,
Do you resolve your case ?
BR

Cisco MSE CMX feature

hi all,
how can I configure POI (point of interest) in cisco MSE ??
I faced this problem when i configure the CMX feature
thanks in advance
appreciation
@leoleo

do share the issue that you are facing and before that check the links provided
check the deployment guide
http://www.cisco.com/c/en/us/products/collateral/wireless/mobility-services-engine/guide-c07-729784.html
and for troubleshooting refer to the link
http://www.cisco.com/en/US/products/ps9742/prod_tech_notes_list.html
****************Do rate helpful posts**************************

Cisco MSE CMX Browser Engange

Guys,
Are there any of you successfully deploy cisco concierge use Cisco MSE browse engange ? Can you give step by step or document step by step to deploy cisco MSE browse engange ?
BR

You can add MSE using the Add Mobility Services Engine dialog box in the Mobility Service page:
http://www.cisco.com/c/en/us/td/docs/wireless/mse/3350/7-5/Mobile_Billboard/Guide/bbx_config_guide/Getting_Started.html

MSE 8.0 - CMX Dashboard password reset procedure

Hi,
I've installed Cisco MSE 8.0.100 on virtual appliance. I would like to use CMX Facebook connector. Therefore I've visited:
https://my_ip_address/dashboard/
and logged in with default login/password (admin/admin). As the very first thing I've changed admin's password. Unfortunately after logging out I can not login with new password. I receive a message:
Account is inactive. Please contact administrator.
Can I reset CMX dashboard settings to the factory defaults? And how?
Kind regards,
Michal

Did you try to stop & start MSE service & see if that helps ?
HTH
Rasika
**** Pls rate all useful responses ****

Do you know where Cisco MSE Demo ova-file is ?

Hello Expert,
I'm looking for Demo File for Cisco MSE.
I checked other thread about same subject.
According to thread, the demo file is able to get from site.
-> http://wnbu-press.cisco.com/blog/2013/03/16/cmx-demo-kit-on-a-usb-stick-guide/
But, Now cannot access its site.
Do you know where Cisco MSE Demo ova-file is ?
I'd appreciate it if you could answer my questions.
Best regards,
takuro

Hello,
If possilble yuou can download the virtual MSE and that has an eval license so you can use it for 60 days I believe.
http://software.cisco.com/download/release.html?mdfid=284294864&flowid=31242&softwareid=282487503&release=7.2.103.0&relind=AVAILABLE&rellifecycle=ED&reltype=latest
This may help you out.

Cisco MSE not detect the specific place

Hi all,
I have a Cisco MSE 7.6.100 with Cisco PI 1.4 and Virtual controller 7.4.121 and 3 APs (3600,3600 and 1600) to make the MSE to detect the location in accurate but I found that when I moved from Area to another Area (each area is covered by AP) the wireless client not associated on the New AP that is on the new Area which reflect on the accuracy of the Location detection.
this scenario is made to test MSE-CMX feature.
please advice to solve this problem.

If you have issues you handover you need to make sure that the overlapping between the channels is proper and the 50 % overlapping is there.
When designing a WLAN, overlapping RF cell coverage is necessary to provide for seamless roaming. However, the overlapping coverage cells should not have overlapping frequency space. In the United States there are only three channels (1, 6 and 11) that do not share frequency space. RF is a half-duplex medium that allows for the transmission of only a single radio on any frequency channel, therefore when three or more 2.4 GHz APs are needed to cover an enterprise facility, only the non-overlapping channels of one, six and eleven should be used.
802.11b/g/n Wi-Fi radios can transmit in the 2.4 GHz band with a total of fourteen available channels. In the US only eleven of those channels are legally available and only 13 are available in Europe.
within the 2.4 GHz band, only three channels have non-overlapping frequency space: channels one, six and eleven.

Can cisco MSE(mobility service engine) configured to work with non-cisco access points?

I understand that access points can be configured to forwards all the probe requests to cisco wifi controller. cisco MSE(mobility service engine) gets the probes from wifi controller to find the location of the mobile devices.
My question, can cisco MSE(mobility service engine) be configured to work with non-cisco access points?

No and the reason why is the NMSP communication from the MSE to the WLC. Other vendors don't support this so there is no communication happening.
-Scott

Is Cisco Prime required to use Cisco MSE?

I recently purchased a Cisco MSE 3355 with locator licenses. I have 2- Cisco ISE's and 2 - WLC 5508s.
Is it required to use Cisco Prime in order to see the location services that the MSE is providing?
If so, what type of license do I need?

Prime Infrastructure is required and you need to purchase enough lifecycle license to have a license for every AP you have. Details of the license options are below:
https://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/prime-infrastructure/guide-c07-731621.html

CISCO MSE installation

Can we install CISCO MSE in MS Hyper V ?
the minimum requirment for the MSE server is a dual processor server, can we install it on a server with single processor ?

You need to make sure that you can meet the requirements of the MSE version. V7.6 supports hyper-v
?Hyper-V 2012
?Hyper-V 2008
?XenServer
http://www.cisco.com/c/en/us/td/docs/wireless/mse/3350/release/notes/mse7_6_100_0.html
Hardware requirements
http://www.cisco.com/c/en/us/td/docs/wireless/mse/7-6/Virtual_Appliance/Guide/Cisco_MSE_VA_Config_Guide/Virtual_Appliance_Introduction.html
Sent from Cisco Technical Support iPhone App

Cisco-MSE

Dear Experts,
Cisco MSE suddenly become unreachable from prime2.1
we tried rebooting the service , but all ended up in vain...
Kindly help us to bring up the MSE services up...
Reagrds,
Thushara

dear team,
Kindly provide the clarity ,which ios to be upgraded...

Cisco MSE Best Practice

Hi there,
I have two MSE 3355, MSE-1 for wIPS and MSE-2 for Location.
In the PI (Prime Infrastructure) site maps reports I can't look the wIPS attackers from the MSE-2 Location. It is possible to do this without having the wIPS license in the same server? How can I interoperate the wIPS attacks reports from the MSE-1 to the MSE-2 location base server? What is the best practice for this scenario?
Thanks

Using TACACS+ with ACS especially gives you all of the AAA's - this is better/best practice for mgmt access to Cisco devices imho.
Bilal

Cisco MSE starting up problem

hi all
I installed MSE virtual appliance 7.4.100 and cannot add it on the PI 2.0
I tried to reboot the MSE i found this log
starting ipmi drivers: ipmi_si: unable to find any system interface(s)
[failed]
please advice
kindly find attached photo

Kultivate-
Greetings and welcome to the Apple discussion boards.
It is possible that you are covered by this repair extension program.
Other than that, it seems as though you have tried everything.
Are you absolutely sure that it is not the monitor?
Luck-
-DaddyPaycheck

TFTP to Cisco MSE

Hello;
I have done this on a number of times but haven't written the command down and now I can't remember how to do it.
I want to copy a file from a TFTP server to my MSE, any help much appreciated!

Not sure about TFTP command.But if you use something like WinSCP (if you have windows base PC) you can easily copy file onto MSE using GUI
http://mrncciew.com/2014/09/24/mse-8-0-upgrade/
HTH
Rasika

Cisco MSE RF fingerprinting problem

Hi
When calibrating a floor using the point method, the model built is a good indicator of the signal experienced by the client at certain points. What happens when two buildings are very close together and the client decides to connect to an AP in another building? Both by assumtion and some testing I have found that the client will be placed in the other building, sometimes far away from his real position. How can this be mitigated?

Hi csco12050227,
Do you resolve your case ?
BR

Cisco MSE CMX dashboard

Similar Messages

Maybe you are looking for