CISCO MSE installation

Can we install CISCO MSE in MS Hyper V ?
the minimum requirment for the MSE server is a dual processor server, can we install it on a server with single processor ?

You need to make sure that you can meet the requirements of the MSE version. V7.6 supports hyper-v
?Hyper-V 2012
?Hyper-V 2008
?XenServer
http://www.cisco.com/c/en/us/td/docs/wireless/mse/3350/release/notes/mse7_6_100_0.html
Hardware requirements
http://www.cisco.com/c/en/us/td/docs/wireless/mse/7-6/Virtual_Appliance/Guide/Cisco_MSE_VA_Config_Guide/Virtual_Appliance_Introduction.html
Sent from Cisco Technical Support iPhone App

Similar Messages

Cisco Anyconnect installation

Hello,
i have a problem with Cisco Anyconnect installation on Window7
During installation procedure i get error message and installation stopped without success
can someone help me?
error message say: "there is a problem with Windows Installer package. A program run as part of the setup did not finish as expected. Contact your support personnel or package vendor"
thanks in advance
Gianpaolo

Are you a local admin?
Are their any Antivirus client processes running when you try to install?
Have you ever had AnyConnect installed before on this PC?

Do you know where Cisco MSE Demo ova-file is ?

Hello Expert,
I'm looking for Demo File for Cisco MSE.
I checked other thread about same subject.
According to thread, the demo file is able to get from site.
-> http://wnbu-press.cisco.com/blog/2013/03/16/cmx-demo-kit-on-a-usb-stick-guide/
But, Now cannot access its site.
Do you know where Cisco MSE Demo ova-file is ?
I'd appreciate it if you could answer my questions.
Best regards,
takuro

Hello,
If possilble yuou can download the virtual MSE and that has an eval license so you can use it for 60 days I believe.
http://software.cisco.com/download/release.html?mdfid=284294864&flowid=31242&softwareid=282487503&release=7.2.103.0&relind=AVAILABLE&rellifecycle=ED&reltype=latest
This may help you out.

Cisco MSE CMX feature

hi all,
how can I configure POI (point of interest) in cisco MSE ??
I faced this problem when i configure the CMX feature
thanks in advance
appreciation
@leoleo

do share the issue that you are facing and before that check the links provided
check the deployment guide
http://www.cisco.com/c/en/us/products/collateral/wireless/mobility-services-engine/guide-c07-729784.html
and for troubleshooting refer to the link
http://www.cisco.com/en/US/products/ps9742/prod_tech_notes_list.html
****************Do rate helpful posts**************************

Can cisco MSE(mobility service engine) configured to work with non-cisco access points?

I understand that access points can be configured to forwards all the probe requests to cisco wifi controller. cisco MSE(mobility service engine) gets the probes from wifi controller to find the location of the mobile devices.
My question, can cisco MSE(mobility service engine) be configured to work with non-cisco access points?

No and the reason why is the NMSP communication from the MSE to the WLC. Other vendors don't support this so there is no communication happening.
-Scott

Cisco MSE not detect the specific place

Hi all,
I have a Cisco MSE 7.6.100 with Cisco PI 1.4 and Virtual controller 7.4.121 and 3 APs (3600,3600 and 1600) to make the MSE to detect the location in accurate but I found that when I moved from Area to another Area (each area is covered by AP) the wireless client not associated on the New AP that is on the new Area which reflect on the accuracy of the Location detection.
this scenario is made to test MSE-CMX feature.
please advice to solve this problem.

If you have issues you handover you need to make sure that the overlapping between the channels is proper and the 50 % overlapping is there.
When designing a WLAN, overlapping RF cell coverage is necessary to provide for seamless roaming. However, the overlapping coverage cells should not have overlapping frequency space. In the United States there are only three channels (1, 6 and 11) that do not share frequency space. RF is a half-duplex medium that allows for the transmission of only a single radio on any frequency channel, therefore when three or more 2.4 GHz APs are needed to cover an enterprise facility, only the non-overlapping channels of one, six and eleven should be used.
802.11b/g/n Wi-Fi radios can transmit in the 2.4 GHz band with a total of fourteen available channels. In the US only eleven of those channels are legally available and only 13 are available in Europe.
within the 2.4 GHz band, only three channels have non-overlapping frequency space: channels one, six and eleven.

Is Cisco Prime required to use Cisco MSE?

I recently purchased a Cisco MSE 3355 with locator licenses. I have 2- Cisco ISE's and 2 - WLC 5508s.
Is it required to use Cisco Prime in order to see the location services that the MSE is providing?
If so, what type of license do I need?

Prime Infrastructure is required and you need to purchase enough lifecycle license to have a license for every AP you have. Details of the license options are below:
https://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/prime-infrastructure/guide-c07-731621.html

Cisco-MSE

Dear Experts,
Cisco MSE suddenly become unreachable from prime2.1
we tried rebooting the service , but all ended up in vain...
Kindly help us to bring up the MSE services up...
Reagrds,
Thushara

dear team,
Kindly provide the clarity ,which ios to be upgraded...

Cisco MSE CMX Browser Engange

Guys,
Are there any of you successfully deploy cisco concierge use Cisco MSE browse engange ? Can you give step by step or document step by step to deploy cisco MSE browse engange ?
BR

You can add MSE using the Add Mobility Services Engine dialog box in the Mobility Service page:
http://www.cisco.com/c/en/us/td/docs/wireless/mse/3350/7-5/Mobile_Billboard/Guide/bbx_config_guide/Getting_Started.html

Cisco MSE Best Practice

Hi there,
I have two MSE 3355, MSE-1 for wIPS and MSE-2 for Location.
In the PI (Prime Infrastructure) site maps reports I can't look the wIPS attackers from the MSE-2 Location. It is possible to do this without having the wIPS license in the same server? How can I interoperate the wIPS attacks reports from the MSE-1 to the MSE-2 location base server? What is the best practice for this scenario?
Thanks

Using TACACS+ with ACS especially gives you all of the AAA's - this is better/best practice for mgmt access to Cisco devices imho.
Bilal

Cisco MSE CMX dashboard

Hi,
I have some problem with CMX dashboard configuration, I followed the configuration guide (http://www.cisco.com/c/en/us/td/docs/wireless/mse/7-6/CMX_Dashboard/Guide/Cisco_CMX_Dashboard_Config_Guide.html) and can't understand, how do I add a map to CMX dashboard to define points of interest, all I can see is only gray screen with button "Update Floors Maps" and when I press it - nothing happens. However CMX analytic works just fine, and maps fully syncronized with cisco Prime

"The maps and location data for the campus, building, or floor are uploaded to the Prime Infrastructure and synchronized with the Location MSE. The CMX Dashboard displays these maps."
Well, it doesn't, I don't see any maps which I created in cisco Prime and syncronized with MSE
"Click the white triangular icon in the right pane located at the left side of System Campus."
There is no System Campus when I click on white triangle

Cisco ISE Installation

HI SIRS
I have a big problem with cisco identity service engine 1.0 ,
cisco said that you can install this software on esx 4.0 , I have tried it but in does not work ,
Is there anyone here to work with this new software?
I wonder , if you could help me.
BEST REGARDS.

For the ISE installation (any version) kindly refer to the hardware requirement this helps and make installation very easy. Also do check the following links for vmware machine and ise installation
http://www.cisco.com/en/US/docs/security/ise/1.1.1/installation_guide/ise_vmware.html
http://www.youtube.com/watch?v=TZuCK610TJI

Cisco ISE installation on VMware Workstation ?

I am trying to install Cisco ISE image through Vmaware Workstation , but after starting VM getting redhat console but not the same console required for setup of actual ISE . Would like to know whether VMware workstation supported for ISE installation as all the cisco docs specifies the image to be mounted on ESX server, then login to client to run setup.. Please help...

Cisco "Officially" supports VMWare's ESXi/vSphere platform. Yes, ISE works in VMWare Workstation, but is not tested on every hardware platform available, therefore, not supported. The the case mentioned above,
I've started installing ISE 1.2 (redhat linux 5 64 bit) , looking at the posts above.. on VMware workstation 9..
1stly I gave 6gb ram ( my laptop has 6 gb ram & 290gb free space ) and started the installation process..
then after the starting stage of checking the requirements of my laptop started and the formatting of the disk began , my lap became very slow & it got hanged there..all my pc processes moved like snails..!! got frustated..
then I restarted my lap and this time I gave 4gb ram .. and it worked fine from then on..
can anyone tell me , if this has to do anthing with the physical memory we give over there in the ise installtion process..does it actually use the entire ram we mention over there..??
Niklas
All possible System RAM was allocated to the ISE VM, and the ISE VM used ALL of the RAM leaving none for the host OS, thereby slowing the machine to a crawl. Once this Virtual RAM was sized to the ISE minimum of 4GB (leaving 2GB dedicated to the host OS), the machine worked correctly. Yes, the ISE VM will happily use ALL the RAM allocated to it.
This is also the reason that Virtual Box and other "Desktop" class virtualization environments cannot be supported across the board. Nearly every machine hosting VMWare Workstation, Virtual Box, etc... has a different chipset, video card, HD controller, and on, and on...
The best thing to do for your situation is to try to install it. If it works, document your EXACT system configuration and the EXACT virtual configuration so that you may look back to it for future installs. You can also use this information to "tweak" the virtual settings until you get a combination that works for you. This will help to document the configurations that do not work on YOUR desktop environment.
Please Rate Helpful posts and mark this question as answered if, in fact, this does answer your question. Otherwise, feel free to post follow-up questions.
Charles Moreton

Cisco CallManager Installation

As new in Voice Networks, I have a question ! Is Cisco CallManager Solution must be installed on designated / cisco recomended hardware. I want to try it before going a head with buying stuff. Can i install it on my server machines with Windows 2000 Server ??
If any one was successfull please let me know.
thanks,
Shakeel

This is how to get CallManager 4.1.3 running on non-MCS server.
1. Install Windows 2000 server (15 gig partition). Make all passwords the same, including WIN2K account. (I used " cisco" )
2. Keep all the default installation components,
just add DHCP under Network Services,
and SNMP under Management and Monitoring tools.
3. Assign a static IP.
4. If installing in VMware, install VMware tools (under the main VM tab ) .
5. Install SP3 (at-least). (or make an win200 boot CD yourself with slipstream( google: XP slipstream)
6. Setup DHCP scope and options, don't forget to add the CISCO TFTP option 150
7. Copy the text below into a text file and name it with a .reg extension,
double click this file to make the changes to the registry.
7a) ccmreg1.reg
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SOFTWARE\Cisco Systems\Model]
"Hardware"="MCS7825H02"
"Speed"="2268"
"Memory"="2048"
[HKEY_LOCAL_MACHINE\SOFTWARE\Spirian\System Info\OS Image]
"Version"="2000.2.6"
[HKEY_LOCAL_MACHINE\SOFTWARE\Spirian\System Info\OS Service Release]
"Version"="2000.2.6sr5"
7b) install win-OS-Upgrade-K9.2000-2-7.exe
7c) ccmreg2.reg
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SOFTWARE\Cisco Systems\Model]
"Hardware"="MCS7825H02"
"Speed"="2268"
"Memory"="2048"
[HKEY_LOCAL_MACHINE\SOFTWARE\Cisco Systems\Spirian]
"ProductKey"="BTOOVQESCCJUIEBI"
"Deployed"="0000000000000000"
8. copy c:\program\cisco\updates\2000 2.7sr5\shutdown.exe naar c:\utils
9. Install CallManager 4.1(3)
ccmsetup.exe
10. Go to Start >> Programs >> CCM 4 >> CallManager Administration and IE will open.
11. Go To Menu >> Application >> CCM Serviceability >> Tools >> Service Activation.
>>Click> on server u want to configure on left hand side.
>>Click> "Cisco RIS Data Collector" and press update.
>>Click> on all the services one by one and press update.
12. You should now have CallManager 4.1(3) running.
13. Upgrade OS and CCM with all patches if needed.
14 you can use P2V to make an copy of an working CM to a VMware machine

Cisco MSE starting up problem

hi all
I installed MSE virtual appliance 7.4.100 and cannot add it on the PI 2.0
I tried to reboot the MSE i found this log
starting ipmi drivers: ipmi_si: unable to find any system interface(s)
[failed]
please advice
kindly find attached photo

Kultivate-
Greetings and welcome to the Apple discussion boards.
It is possible that you are covered by this repair extension program.
Other than that, it seems as though you have tried everything.
Are you absolutely sure that it is not the monitor?
Luck-
-DaddyPaycheck

CISCO MSE installation

Similar Messages

Maybe you are looking for