Cisco Network Assistant - 6509 & 3750 & 3960S

.

You really cannot do much with a 6509 (VSS or otherwise) from CNA. Note the specifc answer to your question is covered in the Release Notes:
Note
The Topology View of Network Assistant supports Catalyst 6500 switches. You cannot add these devices to a community or cluster, but you can start device manager for them from the Topology view.
Cisco really steers you to their enterprise class network management products (e.g., Cisco Prime LMS) for the 6500 product line.
Hope this helps.

Similar Messages

  • Wrong Port Statistics in Cisco Network Assistant

    Hello,
    I'm having some troubles with CNA (version 6.0). There's a few switches in the network that displays wrong information about sports activities/statistics. I've got some ports administratively down, without activity, however CNA is showing Tx and Rx rates, etc. I've already cleared counters from the application and from CLI too. If I do "show interface Gix/x/x" in the CLI, it returns results that I waited, but not in CNA, where it's showing wrong information. Moreover, some ports which should have activity and statistics, don't displays info. All rates and statistics shows 0 when I'd must see any number except 0.
    I'm talking about a stack with 3 Catalyst 3750-X 48P.
    Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 15.0(2)SE5, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2013 by Cisco Systems, Inc.
    Compiled Fri 25-Oct-13 12:38 by prod_rel_team
    ROM: Bootstrap program is C3750E boot loader
    BOOTLDR: C3750E Boot Loader (C3750X-HBOOT-M) Version 12.2(53r)SE2, RELEASE SOFTWARE (fc1)
    Thanks,
    Kind regards,

    In Cisco Network Assistant, under smart ports, if I configure the switch port as Cisco Wireless/Router, it hard  codes the interface as Trunk.In this particular case what is the reason for hard coding it as trunk?
    When you are dealing with autonomous wireless access point, it's very common to have mutiple VLANs configured in the WAP, therefore you need a Trunk switch port.
    You can also configure the trunk port to allow VLANs of your choice.

  • Cisco Network Assistant doesn't start correctly

    Hi!
    A bit of background:
    We've been replacing our 'old' Catalyst 3550 boxes with 3750 Switches, and since the web-interface on these are 'a bit lacking' in functionality(to say the least), we figured that CNA(downloaded latest version) would be just the thing...
    Except, when we try to start it, we get this message:
    Read/write access problems:
    Ingen tilgang
    =======================================
    Note: Read/write access is required for user home directory and installation directory:
    C:\Documents and Settings\BOFH
    C:\Programfiler\Cisco Systems\Cisco Network Assistant
    =======================================
    'Ingen adgang' is Norwegian for 'No access'.
    Also, I've altered my profile name in the message(No need to give away login name, is there? :-)
    Now, my PC is set up according to 'best practices' for a SECURE NETWORKED PC In an office environment.
    In other words, my user doesn't have write access to any folder in the %Program Files% areas, and that's the way we like to keep it...
    So, Who goofed up the software, and how do I get around it without compromising the security of my PC?

    That is NOT a solution.
    The reason why a user shouldn't have write access to the \program files\ folder is that it contains EXECUTABLE BINARIES, which many virii likes to infect.
    Moving the install to another folder and giving a user write access to that just moves the problem to another place.
    What COULD help is a list of subfolders(which doesn't contain binaries or other easily-infected files) or files which the program needs to have write access to, or an updated version which stores its config data somewhere else...

  • Cisco network assistant username

    hi everyone !
    i have two stacked 3750 and i use cisco network assistant for remote access.
    i have created a user witch the following command :
    username <myusername> privilege 15 password 0 <mypassword>
    i would like to force the use of that username/password for network assistant : i can currently login with my enable password (without username), and that is something i do not want.
    it would be great if someone could help me doing this
    thanx
    clem

    Hi Nagendra !
    yes "login local" is enabled.
    i've seen just now that network assistant access the stack with HTTP.
    is there any mean to limit HTTP access to one user ?
    cheers
    clem

  • Cisco Network Assistant (CNA) 5.6 is launched

    Hi Netpro community! I am very pleased to announce the general availability of Cisco Network Assistant version 5.6.
    While we wish CNA was available sooner, we know there is a lot of pent up demand for device support for the 2960-S, 3750-X, and many new 4k devices. Even without a release for approximately 18 months, CNA had over 100,000 downloads in 2010 and 2009, and we hope to see that number climb with the popularity of Cisco's new fixed and modular switches. Thanks for your patience and we hope you enjoy and utilize the simple, intuitive network management CNA provides.
    If you have any feedback on the product or questions, please feel free to contact me at [email protected]
    Bob Krentler, product manager

    Hi Robert,
    I think your initiative to post a message here, anouncing a new version, is a very good one.
    I have had multiple times where a new version of a product had appeared on CCO but I missed it.
    A generic place (feed) where new NMS releases are anounced would be quite helpfull for me.
    Cheers,
    Michel

  • Cisco Network Assistant - Why "No IP Address"?

    I've recently updated Cisco Network Assistant to the latest verison -  5.8 (9.1) but I'm seeing something I've never noticed before.
    In the Topology view one of my 3750's displays "No IP Address"  underneath it, but it does have an IP address set on Vlan245. Admittedly  Vlan1 has "no ip address" set but this is the same setup as another  3750 in that community which *does* show the correct IP address!
    If I right click the switch with the error and click "Properties" the correct IP address is shown (see below).
    I  don't know if this may have a bearing on the error but both the 3750's  in the topology were previously stacked, though we purposely broke the  stacking some time ago.
    Also some other things:
    I don't like having to give permissions in my "Program Files" to get the application working - bad practise!
    I don't ike the Courier-style font in the Device Authentication  dialog that pops up after selecting a community - it looks completely  alien to the rest of the application
    Hope someone can suggest something or fix CNA.
    Thanks.
    Craig

    Try creating a new network location.
    System Preferences -> Network -> Location

  • Cisco Network Assistant, unable to add a switch

    I have a network running some 20 switches, two controllers and many AP's.  All the devices that should be able to connect to cisco network assistant can successfully.  However there is one switch that will show in neighbours but will give the message of “unable to connect to device” when I try and add it to the topology. 
    As far as I can see the config is identically to all other similar switches in the network.  I can telnet from a switch (management VLAN) to the switch in question.  However when I try to ping or telnet from the PC running network assistant (different subnet) I am unsuccessful.  However I can ping/telnet to all other cisco device from this PC. 
    The switch is a WS-C3560-48TS and I have included the config for firstly the switch in question and another switch of the same model and config that works correctly.  Any help would be greatly appreciated, thank you.    
    sho run
    Building configuration...
    Current configuration : 7363 bytes
    version 12.2
    no service pad
    service timestamps debug datetime localtime
    service timestamps log datetime localtime
    service password-encryption
    hostname wc3_switch_1
    enable secret 5 $1$Fn0U$2rG6DadA8JSUzQzSNmMc4/
    enable password 7 1511021F0725
    username dis privilege 15 secret 5 $1$b3d.$S43CM1xtXyEtO5Rsil6Bn1
    username admin privilege 15 password 7 0811185C224C543341
    no aaa new-model
    ip subnet-zero
    ip routing
    no ip domain-lookup
    no file verify auto
    spanning-tree mode pvst
    spanning-tree extend system-id
    vlan internal allocation policy ascending
    interface FastEthernet0/1
    description ### Connected to Parkside-AP05 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/2
    description ### Connected to Parkside-AP06 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/3
    description ### Connected to Parkside-AP07 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/4
    description ### Connected to Parkside-AP08 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/5
    description ### Connected to Parkside-AP12 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/6
    description ### Connected to Parkside-AP13 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/7
    description ### Connected to Parkside-AP20 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/8
    description ### Connected to Parkside-AP21 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/9
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/10
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/11
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/12
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/13
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/14
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/15
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/16
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/17
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/18
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/19
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/20
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/21
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/22
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/23
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/24
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/25
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/26
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/27
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/28
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/29
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/30
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/31
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/32
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/33
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/34
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/35
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/36
    description ### Connected to Parkside-AP36 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/37
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/38
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/39
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/40
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/41
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/42
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/43
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/44
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/45
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/46
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/47
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/48
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface GigabitEthernet0/1
    description *** Connected to WC2A_Core_Switch ***
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface GigabitEthernet0/2
    description *** Connected to wc3_switch_2 ***
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface GigabitEthernet0/3
    shutdown
    interface GigabitEthernet0/4
    shutdown
    interface Vlan1
    ip address 10.0.0.31 255.255.255.0
    ip default-gateway 10.0.0.254
    ip classless
    ip http server
    control-plane
    line con 0
    password 7 144711185D07
    logging synchronous
    login local
    line vty 0 4
    password 7 144711185D07
    logging synchronous
    login local
    line vty 5 15
    password 7 094F471A1A0A
    no login
    end
    wc3_switch_2#sho run
    Building configuration...
    Current configuration : 7239 bytes
    version 12.2
    no service pad
    service timestamps debug datetime localtime
    service timestamps log datetime localtime
    service password-encryption
    hostname wc3_switch_2
    enable secret 5 $1$Sfoj$a6AdO7PI0bP8ERhpWl3OP.
    username dis privilege 15 secret 5 $1$D9c6$16yFzETOxBNHiPdTEqkxQ1
    username admin privilege 15 password 7 133543002059550E78
    no aaa new-model
    ip subnet-zero
    no ip domain-lookup
    no file verify auto
    spanning-tree mode pvst
    spanning-tree extend system-id
    vlan internal allocation policy ascending
    interface FastEthernet0/1
    description ### Connected to Parkside-AP24 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/2
    description ### Connected to Parkside-AP27 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/3
    description ### Connected to Parkside-AP28 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/4
    description ### Connected to Parkside-AP30 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/5
    description ### Connected to Parkside-AP31 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/6
    description ### Connected to Parkside-AP32 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/7
    description ### Connected to Parkside-AP33 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/8
    description *** Curric4 VLAN Port ***
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/9
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/10
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/11
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/12
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/13
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/14
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/15
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/16
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/17
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/18
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/19
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/20
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/21
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/22
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/23
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/24
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/25
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/26
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/27
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/28
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/29
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/30
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/31
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/32
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/33
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/34
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/35
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/36
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/37
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/38
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/39
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/40
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/41
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/42
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/43
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/44
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/45
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/46
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/47
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/48
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface GigabitEthernet0/1
    description *** Connected to wc3_switch_1 ***
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface GigabitEthernet0/2
    description *** Connected to wc3_switch_3 ***
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface GigabitEthernet0/3
    shutdown
    interface GigabitEthernet0/4
    shutdown
    interface Vlan1
    ip address 10.0.0.32 255.255.255.0
    ip default-gateway 10.0.0.254
    ip classless
    ip http server
    control-plane
    line con 0
    password 7 135514015A0F
    logging synchronous
    login local
    line vty 0 4
    password 7 135514015A0F
    logging synchronous
    login local
    line vty 5 15
    no login
    end

    The switch configurations look pretty straightforward and mostly correct.
    I notice that the problem switch has "ip routing" global command. Why is that necessary? You are only using it as a L2 switch, yes?  If you use "ip routing" and have no routing process (ospf, eigrp, etc.) running you would need to add a static default route (ip route 0.0.0.0 etc.) and not use the "ip default-gateway" command. Otherwise the switch itself (the SVI) does not know how to leave the management VLAN routing-wise since it is the only L3 interface defined.
    (I might also add "ip http authentication local" on each and I'd definitely disable telnet in favor of ssh)

  • Software Cisco Network Assistant for Switch SMB?

    Is there any management software as the Cisco Network Assistant for smb switch as SLM224G or SRW224G4-K9-NA, or only works with models 2960 and higher?

    The SX300 series switch will work with CCA. But it does not work with CNA.
    -Tom
    Please rate helpful posts

  • Can't create VLAN's with Cisco Network Assistant

    Hello everyone
    I have a problem with my newest Switch, a WS-C2960X-48TS-L
    Normaly I can programm all my Switches with Cisco Network Assistant. But now I have a problem with creating VLAN's. I can create them, safe them but after a refresh, all the new VLAN's are gone!
    I updated the CNA to the newest Build 6.0 and updated the Switch to 15.2(2)E, but nothing helps!
    Over the CLI I can do everything, but this is not a option for me! To programm sometimes a switch CNA is perfect for me! If it works!!
    Thanks 
    Tobi

    yes I can programm the vlan's over CLI. That's works. I have not tested this if its really works, but the VLAN's are programmed.
    hmm I checked the STP / VTP settings with a second identical Switch, but there are no differents. Made a backup of one Switch and restore on the other One, but I'm still not able to create VLAN's.
    however, I contacted my vendor today, he tell me that it shouldt be a problem to take back the switch. 
    Best regards
    Tobi

  • ESW-520-24-K9 and Cisco Network Assistant

    HI,
    Is this switch model ESW-520-24-K9 is supported by Cisco Network Assistant.
    In the leatest release notes of CNA are supported Catalyst Express 520 Series Switches and this model WS-CE520-24TT-K9 is on the supported list.
    But the mention model above is EoL and the new one is ESW-520-24-K9.
    Thanks,
    Kamil

    Hi Dave,
    Thanks for your replay.
    Yes, you are right that this switch model is supported by CCA but not by Cisco Network Assistant.
    These programs are different in functionality.
    The situation has become clearer, since the customer bought the Cisco Catalyst 2960 series switch.
    Kamil

  • Support Cisco Catalyst 6880 in Cisco Network Assistant

    Hello, tell me, when will support cisco catalyst 6880 in Cisco Network Assistant?

    No it doesnt support.
    Ref:
    http://www.cisco.com/c/en/us/td/docs/net_mgmt/cisco_network_assistant/version6/relnotes/ol32368.html#73942
    HTH
    Inayath
    *plz dont forget to rate if this info is helpfull.

  • Are the SG500P SMB switchs supported for Cisco Network Assistant?

    Hi, we need to enroll some SG500-28P switches to a CNA? Is this possible? I suppose that CDP feature allow this. Actually, i have installed CNA Ver. 6.0. Thanks in advance.

    Hello Fernando,
    Thank you for visiting the Cisco Support Community! 
    Here is a list of all the devices supported by the Cisco Network Assistant for the 6.0 version and later. Many of the 500 series switches, including the SG500-28P Managed Switch, are supported by the CNA. This page will also give you any additional information you may need such as the features of the CNA 6.0 version, any system requirements, and more. 
    If this post was helpful, please remember to mark this question as resolved to help others in the community! If you have any further questions, please do not hesitate to ask!
    Best,
    LP

  • 2960S-48FPD and Cisco network Assistant

    Hi all,
    I'm using Cisco network Assistant V5.5 and when I try to discover WS-C2960S-48FPD-L I have this message :
    Unsuported device type ... cannot add device to commuity
    Any have a solution to that problem ??
    Thank's, Laurent

    Hi Laurent,
    This switch is not supported by Cisco Network Assistant yet.

  • WS-2960-48TC-L and Cisco Network Assistant

    Hello all!
    I have WS-2960-48TC-L in
    #show ver
    Switch Ports Model              SW Version            SW Image
    *    1 50    WS-C2960+48TC-L    15.0(2)EZ             C2960-LANBASEK9-M
    In Cisco Network Assistant (ver. 5.8.(9.1)) I can not  add a switch to the community? And Why in Model string we have + (plus) but not - (dash)
    Sorrry for my bad English.

    Hi Dave,
    Thanks for your replay.
    Yes, you are right that this switch model is supported by CCA but not by Cisco Network Assistant.
    These programs are different in functionality.
    The situation has become clearer, since the customer bought the Cisco Catalyst 2960 series switch.
    Kamil

  • What's the username & password when i connect device from cisco network assistant

    what's the username & password when i connect device from cisco network assistant?
    http://i200.photobucket.com/albums/aa273/wallfire02/Capture_zpsa8f5fd2b.jpg

    Although that may be true...
    If I click the "Connect As..." button it asks for a username and password.
    I've experienced connecting to other user's computers on a network.  To gain access to their computer, I just use their username and password.  I've done this before to transfer files without using a flash drive or burned disk. 
    I'm trying to find out what I'm supposed to log on as to gain access to this device...
         My point is that yes, I'm connected to it by wifi.  Otherwise it wouldn't show up; ha-ha! 
    Is my point really that hard to grasp?

Maybe you are looking for