Cisco Network Assistant for multiple access
Hi All,
hopefully this is the right place to post this. We've been looking into Cisco Network Assistant for our "help desk" (all 3 of them) and I was wondering if it is possible to configure CNA for a shared environment.. With that I mean the application will run on a Windows Terminal Server and all 3 users should be able to access it. Currently I've only seen it running localy and each user has to create or import the setting from another user. This is fine until something changes in the enviorenment and that changes are only saved in the local users configuration.
any ideas if something like this is possible with CNA?
Thanks,
Dan
You may have already figured out then where CNA stores it's localized files - in %userdir%/.networkassistant (hidden from view by default).
You could probably hack the system by manually copying (or scripting a copy) between the respective help desk users' directories but it would be an unsupported setup.
You'd also potentially face problems of revision synchronization in the event of multiple users making independent changes - whose is the "right one"?
Similar Messages
-
Software Cisco Network Assistant for Switch SMB?
Is there any management software as the Cisco Network Assistant for smb switch as SLM224G or SRW224G4-K9-NA, or only works with models 2960 and higher?
The SX300 series switch will work with CCA. But it does not work with CNA.
-Tom
Please rate helpful posts -
Cisco network assistant username
hi everyone !
i have two stacked 3750 and i use cisco network assistant for remote access.
i have created a user witch the following command :
username <myusername> privilege 15 password 0 <mypassword>
i would like to force the use of that username/password for network assistant : i can currently login with my enable password (without username), and that is something i do not want.
it would be great if someone could help me doing this
thanx
clemHi Nagendra !
yes "login local" is enabled.
i've seen just now that network assistant access the stack with HTTP.
is there any mean to limit HTTP access to one user ?
cheers
clem -
Are the SG500P SMB switchs supported for Cisco Network Assistant?
Hi, we need to enroll some SG500-28P switches to a CNA? Is this possible? I suppose that CDP feature allow this. Actually, i have installed CNA Ver. 6.0. Thanks in advance.
Hello Fernando,
Thank you for visiting the Cisco Support Community!
Here is a list of all the devices supported by the Cisco Network Assistant for the 6.0 version and later. Many of the 500 series switches, including the SG500-28P Managed Switch, are supported by the CNA. This page will also give you any additional information you may need such as the features of the CNA 6.0 version, any system requirements, and more.
If this post was helpful, please remember to mark this question as resolved to help others in the community! If you have any further questions, please do not hesitate to ask!
Best,
LP -
Cisco Network Assistant access
Hi,
I installed cisco network assistant, but when I try to import a device by entering a specific IP address (HTTP), it prompts for username/password but it doesn't accept them. The weird thing is that when I enter a specific IP address for a switch device, I can access it through CNA.
What exactly shoud I look at the devices' configuration that I cannot access?
Thank you.The device that works in the CNA doen't have the "ip http authentication" enabled. It seems that this is not the issue. When I enter an IP address to the "Connect to" prompt and select the HTTP protocol and Access-mode "Read-only", it prompts for Username/ Password for "level_15_access", but it doesn't accept them.
-
Cisco Network Assistant access error
Dear all,
I've just installed Cisco Network Assistant (CNA) on my Windows 7 laptop but whenever I try to start it I get an error message as shown below:
Read/write access problems:
Access is denied
=======================================
Note: Read/write access is required for user home directory and installation directory:
C:\Users\...........
C:\Program Files (x86)\Cisco Systems\Cisco Network Assistant
=======================================
My Windows is 64-bit.
Any ideas on how to sort out this will be appreciated.
Regards,
Davis M Onsakiai had the same problem and i wasn't willing to open the whole of the programs directory to what username cisco used when installing or when run, so i opt'ed to install in a root directory, make c:\cisco and install there, that way if there's a permissions error I can add what I wanted, but thats how i got mine to work. Install in a different directory, one that you can add read/write permissions to.
BR Aylu -
Cisco Network Assistant, unable to add a switch
I have a network running some 20 switches, two controllers and many AP's. All the devices that should be able to connect to cisco network assistant can successfully. However there is one switch that will show in neighbours but will give the message of “unable to connect to device” when I try and add it to the topology.
As far as I can see the config is identically to all other similar switches in the network. I can telnet from a switch (management VLAN) to the switch in question. However when I try to ping or telnet from the PC running network assistant (different subnet) I am unsuccessful. However I can ping/telnet to all other cisco device from this PC.
The switch is a WS-C3560-48TS and I have included the config for firstly the switch in question and another switch of the same model and config that works correctly. Any help would be greatly appreciated, thank you.
sho run
Building configuration...
Current configuration : 7363 bytes
version 12.2
no service pad
service timestamps debug datetime localtime
service timestamps log datetime localtime
service password-encryption
hostname wc3_switch_1
enable secret 5 $1$Fn0U$2rG6DadA8JSUzQzSNmMc4/
enable password 7 1511021F0725
username dis privilege 15 secret 5 $1$b3d.$S43CM1xtXyEtO5Rsil6Bn1
username admin privilege 15 password 7 0811185C224C543341
no aaa new-model
ip subnet-zero
ip routing
no ip domain-lookup
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
vlan internal allocation policy ascending
interface FastEthernet0/1
description ### Connected to Parkside-AP05 ###
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/2
description ### Connected to Parkside-AP06 ###
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/3
description ### Connected to Parkside-AP07 ###
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/4
description ### Connected to Parkside-AP08 ###
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/5
description ### Connected to Parkside-AP12 ###
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/6
description ### Connected to Parkside-AP13 ###
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/7
description ### Connected to Parkside-AP20 ###
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/8
description ### Connected to Parkside-AP21 ###
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/9
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/10
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/11
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/12
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/13
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/14
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/15
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/16
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/17
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/18
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/19
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/20
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/21
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/22
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/23
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/24
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/25
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/26
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/27
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/28
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/29
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/30
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/31
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/32
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/33
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/34
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/35
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/36
description ### Connected to Parkside-AP36 ###
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/37
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/38
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/39
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/40
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/41
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/42
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/43
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/44
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/45
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/46
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/47
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/48
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface GigabitEthernet0/1
description *** Connected to WC2A_Core_Switch ***
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface GigabitEthernet0/2
description *** Connected to wc3_switch_2 ***
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface GigabitEthernet0/3
shutdown
interface GigabitEthernet0/4
shutdown
interface Vlan1
ip address 10.0.0.31 255.255.255.0
ip default-gateway 10.0.0.254
ip classless
ip http server
control-plane
line con 0
password 7 144711185D07
logging synchronous
login local
line vty 0 4
password 7 144711185D07
logging synchronous
login local
line vty 5 15
password 7 094F471A1A0A
no login
end
wc3_switch_2#sho run
Building configuration...
Current configuration : 7239 bytes
version 12.2
no service pad
service timestamps debug datetime localtime
service timestamps log datetime localtime
service password-encryption
hostname wc3_switch_2
enable secret 5 $1$Sfoj$a6AdO7PI0bP8ERhpWl3OP.
username dis privilege 15 secret 5 $1$D9c6$16yFzETOxBNHiPdTEqkxQ1
username admin privilege 15 password 7 133543002059550E78
no aaa new-model
ip subnet-zero
no ip domain-lookup
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
vlan internal allocation policy ascending
interface FastEthernet0/1
description ### Connected to Parkside-AP24 ###
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/2
description ### Connected to Parkside-AP27 ###
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/3
description ### Connected to Parkside-AP28 ###
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/4
description ### Connected to Parkside-AP30 ###
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/5
description ### Connected to Parkside-AP31 ###
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/6
description ### Connected to Parkside-AP32 ###
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/7
description ### Connected to Parkside-AP33 ###
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/8
description *** Curric4 VLAN Port ***
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface FastEthernet0/9
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/10
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/11
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/12
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/13
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/14
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/15
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/16
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/17
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/18
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/19
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/20
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/21
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/22
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/23
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/24
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/25
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/26
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/27
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/28
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/29
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/30
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/31
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/32
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/33
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/34
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/35
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/36
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/37
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/38
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/39
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/40
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/41
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/42
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/43
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/44
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/45
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/46
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/47
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface FastEthernet0/48
description *** Curric4 VLAN Port ***
switchport access vlan 6
spanning-tree portfast
interface GigabitEthernet0/1
description *** Connected to wc3_switch_1 ***
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface GigabitEthernet0/2
description *** Connected to wc3_switch_3 ***
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
interface GigabitEthernet0/3
shutdown
interface GigabitEthernet0/4
shutdown
interface Vlan1
ip address 10.0.0.32 255.255.255.0
ip default-gateway 10.0.0.254
ip classless
ip http server
control-plane
line con 0
password 7 135514015A0F
logging synchronous
login local
line vty 0 4
password 7 135514015A0F
logging synchronous
login local
line vty 5 15
no login
endThe switch configurations look pretty straightforward and mostly correct.
I notice that the problem switch has "ip routing" global command. Why is that necessary? You are only using it as a L2 switch, yes? If you use "ip routing" and have no routing process (ospf, eigrp, etc.) running you would need to add a static default route (ip route 0.0.0.0 etc.) and not use the "ip default-gateway" command. Otherwise the switch itself (the SVI) does not know how to leave the management VLAN routing-wise since it is the only L3 interface defined.
(I might also add "ip http authentication local" on each and I'd definitely disable telnet in favor of ssh) -
Wrong Port Statistics in Cisco Network Assistant
Hello,
I'm having some troubles with CNA (version 6.0). There's a few switches in the network that displays wrong information about sports activities/statistics. I've got some ports administratively down, without activity, however CNA is showing Tx and Rx rates, etc. I've already cleared counters from the application and from CLI too. If I do "show interface Gix/x/x" in the CLI, it returns results that I waited, but not in CNA, where it's showing wrong information. Moreover, some ports which should have activity and statistics, don't displays info. All rates and statistics shows 0 when I'd must see any number except 0.
I'm talking about a stack with 3 Catalyst 3750-X 48P.
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 15.0(2)SE5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Fri 25-Oct-13 12:38 by prod_rel_team
ROM: Bootstrap program is C3750E boot loader
BOOTLDR: C3750E Boot Loader (C3750X-HBOOT-M) Version 12.2(53r)SE2, RELEASE SOFTWARE (fc1)
Thanks,
Kind regards,In Cisco Network Assistant, under smart ports, if I configure the switch port as Cisco Wireless/Router, it hard codes the interface as Trunk.In this particular case what is the reason for hard coding it as trunk?
When you are dealing with autonomous wireless access point, it's very common to have mutiple VLANs configured in the WAP, therefore you need a Trunk switch port.
You can also configure the trunk port to allow VLANs of your choice. -
Cisco Network Assistant doesn't start correctly
Hi!
A bit of background:
We've been replacing our 'old' Catalyst 3550 boxes with 3750 Switches, and since the web-interface on these are 'a bit lacking' in functionality(to say the least), we figured that CNA(downloaded latest version) would be just the thing...
Except, when we try to start it, we get this message:
Read/write access problems:
Ingen tilgang
=======================================
Note: Read/write access is required for user home directory and installation directory:
C:\Documents and Settings\BOFH
C:\Programfiler\Cisco Systems\Cisco Network Assistant
=======================================
'Ingen adgang' is Norwegian for 'No access'.
Also, I've altered my profile name in the message(No need to give away login name, is there? :-)
Now, my PC is set up according to 'best practices' for a SECURE NETWORKED PC In an office environment.
In other words, my user doesn't have write access to any folder in the %Program Files% areas, and that's the way we like to keep it...
So, Who goofed up the software, and how do I get around it without compromising the security of my PC?That is NOT a solution.
The reason why a user shouldn't have write access to the \program files\ folder is that it contains EXECUTABLE BINARIES, which many virii likes to infect.
Moving the install to another folder and giving a user write access to that just moves the problem to another place.
What COULD help is a list of subfolders(which doesn't contain binaries or other easily-infected files) or files which the program needs to have write access to, or an updated version which stores its config data somewhere else... -
What's the username & password when i connect device from cisco network assistant
what's the username & password when i connect device from cisco network assistant?
http://i200.photobucket.com/albums/aa273/wallfire02/Capture_zpsa8f5fd2b.jpgAlthough that may be true...
If I click the "Connect As..." button it asks for a username and password.
I've experienced connecting to other user's computers on a network. To gain access to their computer, I just use their username and password. I've done this before to transfer files without using a flash drive or burned disk.
I'm trying to find out what I'm supposed to log on as to gain access to this device...
My point is that yes, I'm connected to it by wifi. Otherwise it wouldn't show up; ha-ha!
Is my point really that hard to grasp? -
Cisco Network Assistant (CNA) Error: Connect
Best regards community,
Please I need your help, I installed Cisco Network Assistant 5.8 (9.1) for manage some catalyst switches as 2950, 2960, 2960S, 2960X, 3750X. I can manage all devices except WS-C2960X-24TS-LL model, I have following message from CNA: "Error: Connect Index: 26, Size:26". This device have same configuration for level 15 access as other devices with user name and password. the catalyst switch IOS version is 15.0(2)EX4
This problem is about either software or hardware? How can solve?
Thanks in advanceYou're welcome.
I know the product team monitor the Network Management Forum. If you post your question there, one of them may pick up on it.
The CNA support typically lags the new product release by about 4-6 months, sometimes longer depending on how well the hardware product release matches up with the network management product's latest release date. The 2960XR just started shipping in July 2013 so a good guess would be that CNA might support it in the next release (5.9?). That's just a guess though. -
Cisco Network Assistant MAC auth issue
I have few Autonomous Access Points all managed by the Cisco Network Assistant. Users have access to wireless only based on MAC authentication.
Every once in a while the wireless access to the Access-Point fails and the following error is showed in the Cisco Network Assistant.
ERROR: The MAC address filter 700 used for association access was not created by the web interface and cannot be displayed.
also
WARNING: Filter 700 was configured on interface Dot11radio 0.170 using CLI. It must be cleared via CLI to ensure proper operation of the web interface.
The Network Admin does not use CLI but this problem keeps coming. To fix this problem I had cleared the access-list 700 via CLI and created a new access-list 700 via Cisco Network Assistant. Adding all the MAC's each time the network goes down is a cumbersome process. Is there a solution for this?
Thanks in advance
error snapshot attached.I have some site admins that use CNA. I just upgraded their LAN to 3560v2 switches running 12.2(58)SE2 and had them upgrade their CNA software to CNA 5.7(6). They reported the same error.
I think you clearly indentified the problem. At one time the IOS command parser accepted both "show mac-address" and "show mac address". At some point IOS stopped accepting the older "show mac-address" format, and CNA is still issuing this command regardless of the IOS version it is trying to manage. -
Cisco Network Assistant and add to comunity problem via HTTPS
hello,
i have big network of cisco switches and all is in my cisco network assistant in comunity connected via HTTPS. if i add new switch to network (all for HTTPS access is configured good: domain name, ip http secure-server, authenticate locale ...) and if i can add this switch to comunity (right click on icon and ADD TO COMUNITY), CNA say "Unable to Connect", because it can connect to switch via HTTP (i have disable it on switch), not via HTTPS. i have never version of CNA ... where is problem? why it not connect to switch via HTTPS? hmmm? thank you ... Peter"The HTTP server interface must be enabled to display the network assistant. " Source.
You can put an access-list on the http server if you are concerned about security exposure. -
Cisco Network Assistant (CNA) 5.6 is launched
Hi Netpro community! I am very pleased to announce the general availability of Cisco Network Assistant version 5.6.
While we wish CNA was available sooner, we know there is a lot of pent up demand for device support for the 2960-S, 3750-X, and many new 4k devices. Even without a release for approximately 18 months, CNA had over 100,000 downloads in 2010 and 2009, and we hope to see that number climb with the popularity of Cisco's new fixed and modular switches. Thanks for your patience and we hope you enjoy and utilize the simple, intuitive network management CNA provides.
If you have any feedback on the product or questions, please feel free to contact me at [email protected]
Bob Krentler, product managerHi Robert,
I think your initiative to post a message here, anouncing a new version, is a very good one.
I have had multiple times where a new version of a product had appeared on CCO but I missed it.
A generic place (feed) where new NMS releases are anounced would be quite helpfull for me.
Cheers,
Michel -
Can't create VLAN's with Cisco Network Assistant
Hello everyone
I have a problem with my newest Switch, a WS-C2960X-48TS-L
Normaly I can programm all my Switches with Cisco Network Assistant. But now I have a problem with creating VLAN's. I can create them, safe them but after a refresh, all the new VLAN's are gone!
I updated the CNA to the newest Build 6.0 and updated the Switch to 15.2(2)E, but nothing helps!
Over the CLI I can do everything, but this is not a option for me! To programm sometimes a switch CNA is perfect for me! If it works!!
Thanks
Tobiyes I can programm the vlan's over CLI. That's works. I have not tested this if its really works, but the VLAN's are programmed.
hmm I checked the STP / VTP settings with a second identical Switch, but there are no differents. Made a backup of one Switch and restore on the other One, but I'm still not able to create VLAN's.
however, I contacted my vendor today, he tell me that it shouldt be a problem to take back the switch.
Best regards
Tobi
Maybe you are looking for
-
Action with new file with size from selection
Hello, I try to record an action that takes a copy of the current image and creates a new file with the same dimensions. The action I record always has the file size of the new image hardcoded in it. I tried to set Preset to Clipboard, but this is no
-
Which Is Better Time Machine or Backup
So I just got a new iMac plus a 1T external drive. I have been using backup on my old mini-mac with an external drive plus I used the drive for iTunes and iPhoto. So which is better TM or the old backup (which I had no problems with). I really do not
-
When I try to back up my purchased music to a DVD I get error #261. Any clue what that is? Thanks Dell Latitude D820 Windows XP
-
OC4J bind socket address issue
Hi i am using DB(9.2.0.6.0) and APPS(11.5.10.2). Now i have cloned a new instance and it runs on port 8050. Now i want to install and configure OC4J with it. I have done the OC4J Installation Successfully. Here i used the OC4J Version 9.0.3.I have c
-
Brand new U530 Touch laptop with Windows 8.1. Whenever I boot up and the MSN account login screen appears, the password line already has multiple lines of key entries. These entries were not generated by me and are not the password. If I backspace t