Cisco Network Assistant Will Not Connect to 3825 Router Using http

Trying to use the CNA to connect to my 3825 router, in preparation for 2960x switches we are going to purchase. I cannot connect using http - read/write. It seems as though the username and password fail. I can however, connect Read – only Level 1, and the username and password work fine and I am logged in. Is there something I can check in the Router configuration for the Network Assistant to work?
Thanks

It will be helpful for other community members to know the solution and cause, if can be shared.
-Thanks
Vinod

Similar Messages

Cisco Network Assistant(CNA) not connecting to access points.

When I create a community with CNA, it finds the 2960 switch and connects to it. However it shows "connection failed" for all the 702i access points. Not sure why it shows connection failed. Any help would be appreciated.
Also, if I try to connect directly to the access point thru CNA, it says not accessible.
Thanks.
Jim

It will be helpful for other community members to know the solution and cause, if can be shared.
-Thanks
Vinod

My ipad recognizes my home network but will not connect to the internet. When I click on AirPort/preferences at the top of the imac screen it says..."AirPort has a self-assigned ip address and may not connect to the internet".How can I change ip address?

My ipad recognizes my home network but will not connect to the internet. When I click on AirPort/preferences at the top of the imac screen it says..."AirPort has a self-assigned ip address and may not connect to the internet". If this is the root of the problem,how can I change ip address?
Ipad will connect no problem to other networks.

First thing you need I think is to get your iMac connected to the Internet.
Shut down your iMac and you iPad. Then power off your router. Wait 30 seconds and power up the router.
After the router indicates that it is connected to the Internet then start up your iMac and see if it connects. If the iMac connects to the Internet then your iPad should too.
If this power up sequence doesn't work you'll have to dig into the router setup to make sure it is working properly.

I installed a new wifi router and airport will not connect automatically to it. It sees the network but will not connect unless I tell it to.

I installed a new wifi router and airport will not connect automatically to it. It sees the network but will not connect unless I tell it to. I can't find anywhere in the utility or network preferences that will allow me to choose this router as the default. How do I fix this? BTW I'm using Lion.

Are there any previous networks that you have used that have the same password as Molly? YES
Using System Preferences > Network > AirPort Advanced again, you need to remove any listings of previous networks that used the same password as Molly. Click the name of the network and click the - (minus) button at the bottom of the list of connections.
Also delete any other networks (except Molly at the top of the list) that might have used the same name...Molly in the past.
Delete any other networks that you no longer need so that your Mac will search for networks more quickly
Click OK, then click Apply
Open KeyChain Access and look for a listing of any old networks that you no longer need. Click to highlight the name of the network, then click the Delete Key on your computer.
Then look for any old networks that might have used the name Molly in the past and do the same for them.
Then look for any old networks that might have used the same password as the password for your "new" Molly network and delete them in the same way
Click the KeyChain Access menu just next to the Apple icon in the upper left corner of the computer screen
and then click KeyChain First Aid
Enter the main administrator password for the Mac you are using and highlight the Repair button. Then click Start. You will see a message that repairs have been completed
Quit Keychain Access
Power down the entire network...all devices...order is not important
Power up the modem first, then your main router, the other devices one at a time
Log on to Molly and see if the Mac remembers it after a few tries. If not, I'm afraid that you will need to change the name of the wireless network and password on your router due to corruption issues on the Mac. You have done everything possible without re-installing the complete operating system.

Just got comcast triple play. Original ipad sees network but will not connect.

Just got comcast triple play. Original ipad sees network but will not connect.

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

"My Windows 7 Dell will see Airport network but will not connect"

"My Windows 7 Dell will see Airport network but will not connect" Can anyone help me out with this?
Thanks,

Yes, I have the Airport utility installed on the Windows 7 dell.

TS1398 My ipad is showing a wi-fi network, but will not connect. I've tried turning off and on, and went through the troubleshooting, still nothing. Then I reset network settings as suggested, still nothing. Any ideas?

My ipad is showing a wi-fi network, but will not connect. I've tried turning off and on, and went through the troubleshooting, still nothing. Then I reset network settings as suggested, still nothing. Any ideas?

that is the router I am on now reply to this message from my desktop, the router seems to be working fine, thanks

My Apple TV recognises my wifi network but will not connect to it, when I enter the password

Help please - my Apple TV recognises my wifi network but will not connect to it, when I enter the password - it just says 'there was a problem connecting to the network - check your settings and try again (5).' What should I do next?

people repport that apple products in general I believe have problems with support for the outdated encryption type called wep encryption which is also pretty useless and easy to break
if you use that try disabling it or changing to wpa encryption
if you use MAC address filtering in your router then you need to add the appletv's MAC address to the positive list

Airport Express/Mac work fine, Vista PC sees network, but will not connect

I have been working on this for two days. What can I do? I have the latest firmware on the airport express and my utilities are up to date on both PC and Vista (airport s/w ver 5.3.2). It all worked before. Also, my brother wireless printer sees network, but will not connect.

I have a similar issue. I have an AP Express set up for WPA2 Personal, G only. My Mac mini connects fine. My Dell mini9 with XP connects fine. My Dell desktop with Vista64 connects fine, but is local only, no internet.
I have completely reset the AP to factory settings and reconfigured it using the Vista machine, but still no luck. What is going on? Anyone?

TS1559 Since upgrading my iPhone5 to the newest iOS (6.1.2) I can longer connect to WiFi. It sees the wireless network but will not connect.. Other devices in my home that weren't upgraded can connect just fine.

Since upgrading my iPhone5 to the newest iOS (6.1.2) I can longer connect to WiFi. It sees the wireless network but will not connect.. Other devices in my home that weren't upgraded can connect just fine.

I had the same problem. I did the reset networks on my iPhone & it did not work. My husband read somewhere that changing the channel on the router to manual & selecting the highest available channel number might help. I did that & it solved the problem. I have not had the problem since.

TS1398 Despite trying the recommended options listed above, my Ipad will not connect to our home Wi-Fi. The problem has only started happening this morning. The ipad recognises the wi-fi network but will not connect.

Despite trying the recommended trouble shooting options, my I pad will not connect to our home Wi-Fi network. The problem only started occurring this morning, and although it will recognise the Wi-Fi network, it will not connect.
Any other options I can try????

Try rebooting the router. Just pull the power for a few seconds. No settings are lost.

7510-e-all in one - c311a will not connect to my router dlink wbr-2310.

I just bought HP Photosmart 7510 e-All-in-One-C311A and it will not connect to my router which is a DLink WBR-2310. The diagnostic results are as follows:
Wireless On: PASS
Wireless Working: PASS
Connected: Not Run
Disconnect count total: 0
Disconnect count (last hour): 0
Disconnect count (last 24 hours): 0
Network Name (SSID) Found: PASS
Other Networks detected matching your network name (SSID) No
Wireless Networks Detected: 10
Printer Settings Consistent with Wireless Router Settings: PASS
No Filtering: FAIL
Channel: Not Run
Security: PASS
I have checked to make sure MAC addres is not enabled. I have tried turning off computer, router and printer. Please help. I have Windows 7.
Thanks very much!

Hi,
This is how I installed my printer last week (also a 7510).: Using USB cable to connect it to a computer on your network and setup from there. It will ask you to use similar setup for your computer, just accept this The setup was no longer than 5 mins.
Please also check this:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02900814&lc=en&cc=us&dlc=en&product=5070121
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

My Macbook Pro will recognize my network but will not connect to the internet

My macbook will not connect to the internet at home. It works fine on other networks, but at home it will recognize my network name but says it will not be able to connect to the internet. This issue just sort of came up randomly. I have shut the router off (I use Verizon Vios) and reset it and that doesn't work. The little Wifi status at the top of the screen just has an exclamation point over it. I haven't changed any of the default network settings. It just stopped working. When I take it to work and use their network or free wifi available at stores etc...it connects just fine. A few weeks ago upgraded my operating system to Mavericks, but it has worked up until this morning.

Do this. Go to Apple menu / System Preferences / Network.
In the left column, click Wi-Fi. Next click Assist me, then Assistant. Follow the on screen instructions.

Adobe Download Assist will not connect - multiple attemps

I've successfully downloaded a trial version of photoshop, yet when I try to download after effects the ADA will not connect. I have removed the program twice with reinstallation, and still no luck. Advice??

Yes we don't have direct links for the trials. You might try a different web browser as well as a selective start up. What type of virus protection software and software firewall are you using? Did you disable them or direct the software firewall to allow connections from the Adobe Download Assistant?

My iPad can find a network but will not connect to internet ever since i did last software update

Ever since the last software update my iPad will not connect to the internet. I can see the networks and have great signal strength but it just won't connect. Other iPad users who have not done the update can sit next to me and connect with no issues. My iPad is only a month old! not good enough!

There are no changes to WiFi in the last two updates 4.3.4, and 4.3.5. These contained only fixes for a malicious PDF file handling problem, and a security certificate handling problem.
Try using Settings > General > Reset > Reset network settings to see if that fixes your problems.

Cisco Network Assistant Will Not Connect to 3825 Router Using http

Similar Messages

Maybe you are looking for