Cisco Networking Assistant Configuration Archive

Is there a way to use a back up from one switch, say a 3750G, and restore it to another 3750G?  Also, is there a way of editing the archived configuration so that I could change something small like the IP address?  This would allow me to writhe the configuration once, and then restore it to multiple, identical sswitches.                  

No, there's not any supported way to do what you're asking with CNA. Its configuration options are pretty limited - modify port configurations on a discovered community member and upgrade software.
The sort of thing you're looking to do is more of a feature built into Cisco Prime LMS (currently), Prime Infrastructure (2.0 - out next month), or by using Smart Install.

Similar Messages

  • Cisco Network Assistant restore problem

    Hi,
    Recently been using Cisco Network Assistant 5.4 to back up the configuration of my Catalyst 3500XL switches.  However, yesterday for the first time I tried using the Maintenance/Configuration Archive Restore function to load the configuratin on a factory default switch.    The restore went well, and I can see my settings in running-config.    But as soon as the config loaded and the switch reset was done, all of the FastEthernet ports were not working.   Resetting the switch to factory default does restore the ports.   Tried this Resore on a second switch and the same thing happened.   The port status show as "FastEthernet0/1 is down, link protocol is down".   This port is enabled in the configuration.     I can't see any reason for the ports to drop out after reloading the configuration.....  can anyone point me in the right direction?
    Thanks,
    Allen

    figured out what the problem was.  The laptop I was using to program the Cisco switches had been used the previous week to program some PLCs, so the laptop ethenet port was set to 10MBs/Half Duplex.   The running-config of the switches has "speed 100, duplex full" set for all the ports.  So before the configuration was loaded, the ethernet port connections worked, I didn't notice I was connecting at 10/Half.  Once the Restore was done, it would drop all connections like the laptop trying to connect at 10MBs.  So all the ports 'appeared' to be dead, when they were just waiting for a 100MBs connection.   

  • Cisco Network Assistant, unable to add a switch

    I have a network running some 20 switches, two controllers and many AP's.  All the devices that should be able to connect to cisco network assistant can successfully.  However there is one switch that will show in neighbours but will give the message of “unable to connect to device” when I try and add it to the topology. 
    As far as I can see the config is identically to all other similar switches in the network.  I can telnet from a switch (management VLAN) to the switch in question.  However when I try to ping or telnet from the PC running network assistant (different subnet) I am unsuccessful.  However I can ping/telnet to all other cisco device from this PC. 
    The switch is a WS-C3560-48TS and I have included the config for firstly the switch in question and another switch of the same model and config that works correctly.  Any help would be greatly appreciated, thank you.    
    sho run
    Building configuration...
    Current configuration : 7363 bytes
    version 12.2
    no service pad
    service timestamps debug datetime localtime
    service timestamps log datetime localtime
    service password-encryption
    hostname wc3_switch_1
    enable secret 5 $1$Fn0U$2rG6DadA8JSUzQzSNmMc4/
    enable password 7 1511021F0725
    username dis privilege 15 secret 5 $1$b3d.$S43CM1xtXyEtO5Rsil6Bn1
    username admin privilege 15 password 7 0811185C224C543341
    no aaa new-model
    ip subnet-zero
    ip routing
    no ip domain-lookup
    no file verify auto
    spanning-tree mode pvst
    spanning-tree extend system-id
    vlan internal allocation policy ascending
    interface FastEthernet0/1
    description ### Connected to Parkside-AP05 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/2
    description ### Connected to Parkside-AP06 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/3
    description ### Connected to Parkside-AP07 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/4
    description ### Connected to Parkside-AP08 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/5
    description ### Connected to Parkside-AP12 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/6
    description ### Connected to Parkside-AP13 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/7
    description ### Connected to Parkside-AP20 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/8
    description ### Connected to Parkside-AP21 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/9
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/10
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/11
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/12
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/13
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/14
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/15
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/16
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/17
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/18
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/19
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/20
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/21
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/22
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/23
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/24
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/25
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/26
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/27
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/28
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/29
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/30
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/31
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/32
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/33
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/34
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/35
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/36
    description ### Connected to Parkside-AP36 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/37
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/38
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/39
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/40
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/41
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/42
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/43
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/44
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/45
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/46
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/47
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/48
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface GigabitEthernet0/1
    description *** Connected to WC2A_Core_Switch ***
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface GigabitEthernet0/2
    description *** Connected to wc3_switch_2 ***
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface GigabitEthernet0/3
    shutdown
    interface GigabitEthernet0/4
    shutdown
    interface Vlan1
    ip address 10.0.0.31 255.255.255.0
    ip default-gateway 10.0.0.254
    ip classless
    ip http server
    control-plane
    line con 0
    password 7 144711185D07
    logging synchronous
    login local
    line vty 0 4
    password 7 144711185D07
    logging synchronous
    login local
    line vty 5 15
    password 7 094F471A1A0A
    no login
    end
    wc3_switch_2#sho run
    Building configuration...
    Current configuration : 7239 bytes
    version 12.2
    no service pad
    service timestamps debug datetime localtime
    service timestamps log datetime localtime
    service password-encryption
    hostname wc3_switch_2
    enable secret 5 $1$Sfoj$a6AdO7PI0bP8ERhpWl3OP.
    username dis privilege 15 secret 5 $1$D9c6$16yFzETOxBNHiPdTEqkxQ1
    username admin privilege 15 password 7 133543002059550E78
    no aaa new-model
    ip subnet-zero
    no ip domain-lookup
    no file verify auto
    spanning-tree mode pvst
    spanning-tree extend system-id
    vlan internal allocation policy ascending
    interface FastEthernet0/1
    description ### Connected to Parkside-AP24 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/2
    description ### Connected to Parkside-AP27 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/3
    description ### Connected to Parkside-AP28 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/4
    description ### Connected to Parkside-AP30 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/5
    description ### Connected to Parkside-AP31 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/6
    description ### Connected to Parkside-AP32 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/7
    description ### Connected to Parkside-AP33 ###
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/8
    description *** Curric4 VLAN Port ***
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface FastEthernet0/9
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/10
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/11
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/12
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/13
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/14
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/15
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/16
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/17
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/18
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/19
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/20
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/21
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/22
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/23
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/24
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/25
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/26
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/27
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/28
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/29
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/30
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/31
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/32
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/33
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/34
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/35
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/36
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/37
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/38
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/39
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/40
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/41
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/42
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/43
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/44
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/45
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/46
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/47
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface FastEthernet0/48
    description *** Curric4 VLAN Port ***
    switchport access vlan 6
    spanning-tree portfast
    interface GigabitEthernet0/1
    description *** Connected to wc3_switch_1 ***
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface GigabitEthernet0/2
    description *** Connected to wc3_switch_3 ***
    switchport trunk encapsulation dot1q
    switchport mode trunk
    spanning-tree portfast
    interface GigabitEthernet0/3
    shutdown
    interface GigabitEthernet0/4
    shutdown
    interface Vlan1
    ip address 10.0.0.32 255.255.255.0
    ip default-gateway 10.0.0.254
    ip classless
    ip http server
    control-plane
    line con 0
    password 7 135514015A0F
    logging synchronous
    login local
    line vty 0 4
    password 7 135514015A0F
    logging synchronous
    login local
    line vty 5 15
    no login
    end

    The switch configurations look pretty straightforward and mostly correct.
    I notice that the problem switch has "ip routing" global command. Why is that necessary? You are only using it as a L2 switch, yes?  If you use "ip routing" and have no routing process (ospf, eigrp, etc.) running you would need to add a static default route (ip route 0.0.0.0 etc.) and not use the "ip default-gateway" command. Otherwise the switch itself (the SVI) does not know how to leave the management VLAN routing-wise since it is the only L3 interface defined.
    (I might also add "ip http authentication local" on each and I'd definitely disable telnet in favor of ssh)

  • Wrong Port Statistics in Cisco Network Assistant

    Hello,
    I'm having some troubles with CNA (version 6.0). There's a few switches in the network that displays wrong information about sports activities/statistics. I've got some ports administratively down, without activity, however CNA is showing Tx and Rx rates, etc. I've already cleared counters from the application and from CLI too. If I do "show interface Gix/x/x" in the CLI, it returns results that I waited, but not in CNA, where it's showing wrong information. Moreover, some ports which should have activity and statistics, don't displays info. All rates and statistics shows 0 when I'd must see any number except 0.
    I'm talking about a stack with 3 Catalyst 3750-X 48P.
    Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 15.0(2)SE5, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2013 by Cisco Systems, Inc.
    Compiled Fri 25-Oct-13 12:38 by prod_rel_team
    ROM: Bootstrap program is C3750E boot loader
    BOOTLDR: C3750E Boot Loader (C3750X-HBOOT-M) Version 12.2(53r)SE2, RELEASE SOFTWARE (fc1)
    Thanks,
    Kind regards,

    In Cisco Network Assistant, under smart ports, if I configure the switch port as Cisco Wireless/Router, it hard  codes the interface as Trunk.In this particular case what is the reason for hard coding it as trunk?
    When you are dealing with autonomous wireless access point, it's very common to have mutiple VLANs configured in the WAP, therefore you need a Trunk switch port.
    You can also configure the trunk port to allow VLANs of your choice.

  • Cisco Network Assistant (CNA) Error: Connect

    Best regards community,
    Please I need your help, I installed Cisco Network Assistant 5.8 (9.1) for manage some catalyst switches as 2950, 2960, 2960S, 2960X, 3750X. I can manage all devices except WS-C2960X-24TS-LL model, I have following message from CNA: "Error: Connect Index: 26, Size:26". This device have same configuration for level 15 access as other devices with user name and password. the catalyst switch IOS version is 15.0(2)EX4
    This problem is about either software or hardware? How can solve?
    Thanks in advance

    You're welcome.
    I know the product team monitor the Network Management Forum. If you post your question there, one of them may pick up on it.
    The CNA support typically lags the new product release by about 4-6 months, sometimes longer depending on how well the hardware product release matches up with the network management product's latest release date. The 2960XR just started shipping in July 2013 so a good guess would be that CNA might support it in the next release (5.9?). That's just a guess though.

  • Cisco Network Assistant gui is erratic 5.6.3

    Cisco Network Assistant opens up fine, but i have to click and/or mouseover the center to be able to see the pop-up to connet to a device or comunity
    it is strange
    OS Name:                   Microsoft Windows XP Professional
    OS Version:                5.1.2600 Service Pack 3 Build 2600
    OS Manufacturer:           Microsoft Corporation
    OS Configuration:          Standalone Workstation
    OS Build Type:             Uniprocessor Free
    System Manufacturer:       Acer
    System Model:              TravelMate 290
    System type:               X86-based PC
    Processor(s):              1 Processor(s) Installed. x86 Family 6 Model 9 Stepping 5 GenuineIntel ~1 298 Mhz
    Total Physical Memory:     2,031 MB
    Available Physical Memory: 745 MB
    Virtual Memory: Max Size:  2,048 MB
    Virtual Memory: Available: 1,997 MB
    Virtual Memory: In Use:    51 MB
    thanks

    Hi Luis,
    Few questions :
    - is it the same on all machines you tested CNA on ?
    - is this an upgrade from a previous (and working) version ?
    - is it the English version of Windows, or a localized one ?
    Regards,
    Marc

  • Cisco Network Assistant MAC auth issue

    I have few Autonomous Access Points all managed by the Cisco Network Assistant. Users have access to wireless only based on MAC authentication.
    Every once in a while the wireless access to the Access-Point fails and the following error is showed in the Cisco Network Assistant.
    ERROR: The MAC address filter 700 used for association access was not created by the web interface and cannot be displayed.
    also
    WARNING: Filter 700 was configured on interface Dot11radio 0.170 using CLI. It must be cleared via CLI to ensure proper operation of the web interface.
    The Network Admin does not use CLI but this problem keeps coming. To fix this problem I had cleared the access-list 700 via CLI and created a new access-list 700 via Cisco Network Assistant. Adding all the MAC's each time the network goes down is a cumbersome process. Is there a solution for this?
    Thanks in advance
    error snapshot attached.

    I have some site admins that use CNA.  I just upgraded their LAN to 3560v2 switches running 12.2(58)SE2 and had them upgrade their CNA software to CNA 5.7(6).  They reported the same error.
    I think you clearly indentified the problem.  At one time the IOS command parser accepted both "show mac-address" and "show mac address".  At some point IOS stopped accepting the older "show mac-address" format, and CNA is still issuing this command regardless of the IOS version it is trying to manage.

  • Cisco Network Assistant access

    Hi,
    I installed cisco network assistant, but when I try to import a device by entering a specific IP address (HTTP), it prompts for username/password but it doesn't accept them. The weird thing is that when I enter a specific IP address for a switch device, I can access it through CNA.
    What exactly shoud I look at the devices' configuration that I cannot access?
    Thank you.

    The device that works in the CNA doen't have the "ip http authentication" enabled. It seems that this is not the issue. When I enter an IP address to the "Connect to" prompt and select the HTTP protocol and Access-mode "Read-only", it prompts for Username/ Password for "level_15_access", but it doesn't accept them.

  • Cisco Network Assistant for multiple access

    Hi All,
       hopefully this is the right place to post this.  We've been looking into Cisco Network Assistant for our "help desk" (all 3 of them) and I was wondering if it is possible to configure CNA for a shared environment..  With that I mean the application will run on a Windows Terminal Server and all 3 users should be able to access it.  Currently I've only seen it running localy and each user has to create or import the setting from another user.  This is fine until something changes in the enviorenment and that changes are only saved in the local users configuration. 
    any ideas if something like this is possible with CNA?
    Thanks,
    Dan

    You may have already figured out then where CNA stores it's localized files - in %userdir%/.networkassistant (hidden from view by default).
    You could probably hack the system by manually copying (or scripting a copy) between the respective help desk users' directories but it would be an unsupported setup.
    You'd also potentially face problems of revision synchronization in the event of multiple users making independent changes - whose is the "right one"?

  • Cisco Network Assistant and add to comunity problem via HTTPS

    hello,
    i have big network of cisco switches and all is in my cisco network assistant in comunity connected via HTTPS. if i add new switch to network (all for HTTPS access is configured good: domain name, ip http secure-server, authenticate locale ...) and if i can add this switch to comunity (right click on icon and ADD TO COMUNITY), CNA say "Unable to Connect", because it can connect to switch via HTTP (i have disable it on switch), not via HTTPS. i have never version of CNA ... where is problem? why it not connect to switch via HTTPS? hmmm? thank you ... Peter

    "The HTTP server interface must be enabled to display the network assistant. " Source.
    You can put an access-list on the http server if you are concerned about security exposure.

  • Cisco Network Assistant question

    Hi
    I am a new user of Cisco Network Assistant. I got it to display the network of switches in the topology view. However a couple of switches are not displayed as linked to another switch (i.e shown as seperate from the network). Could someone please let me know why this is happening and how to get the switches to display as linked to another switch.
    Thanks

    Hi Michel
    Thanks for your reply.
    I have the right to see the switches as I am the one who configured all of them from scratch and deployed them. All is working fine except that now I started to look at ways to manage them. I thought I enabled CDP on all of them but I will double check. Also I am not using ACS but planning to in the future.
    Cheers
    Raoul

  • Cisco Network Assistant topology view problem

    hello! I have a problem. I just installed Cisco Network Assistant on my computer, scanned the network and found my switches. The problem is that when the program builds the topology, it desplays the switches in two raws but doesnt draw the links between them. Before installing CNA, i configured the switches with the following commands to enable CNA to see them:
    switch# conf t
    switch(config)# ip http server
    switch(config)# ip http secure-server
    switch(config)# ip http max-connections 16
    switch(config)# ip http ip timeout-policy idle 180 life 180 requests 25
    switch(config)# end
    switch#
    Is there any other settings that i have to make for CNA to show the links between the switches? Thank you very much!

    Both the Catalyst 4506 and 4506-E are supported by CNA. You need to verify reachability from the CNA host and that the target Catalyst has the http (or https) server active. With that, it should work fine.

  • Software Cisco Network Assistant for Switch SMB?

    Is there any management software as the Cisco Network Assistant for smb switch as SLM224G or SRW224G4-K9-NA, or only works with models 2960 and higher?

    The SX300 series switch will work with CCA. But it does not work with CNA.
    -Tom
    Please rate helpful posts

  • Can't create VLAN's with Cisco Network Assistant

    Hello everyone
    I have a problem with my newest Switch, a WS-C2960X-48TS-L
    Normaly I can programm all my Switches with Cisco Network Assistant. But now I have a problem with creating VLAN's. I can create them, safe them but after a refresh, all the new VLAN's are gone!
    I updated the CNA to the newest Build 6.0 and updated the Switch to 15.2(2)E, but nothing helps!
    Over the CLI I can do everything, but this is not a option for me! To programm sometimes a switch CNA is perfect for me! If it works!!
    Thanks 
    Tobi

    yes I can programm the vlan's over CLI. That's works. I have not tested this if its really works, but the VLAN's are programmed.
    hmm I checked the STP / VTP settings with a second identical Switch, but there are no differents. Made a backup of one Switch and restore on the other One, but I'm still not able to create VLAN's.
    however, I contacted my vendor today, he tell me that it shouldt be a problem to take back the switch. 
    Best regards
    Tobi

  • ESW-520-24-K9 and Cisco Network Assistant

    HI,
    Is this switch model ESW-520-24-K9 is supported by Cisco Network Assistant.
    In the leatest release notes of CNA are supported Catalyst Express 520 Series Switches and this model WS-CE520-24TT-K9 is on the supported list.
    But the mention model above is EoL and the new one is ESW-520-24-K9.
    Thanks,
    Kamil

    Hi Dave,
    Thanks for your replay.
    Yes, you are right that this switch model is supported by CCA but not by Cisco Network Assistant.
    These programs are different in functionality.
    The situation has become clearer, since the customer bought the Cisco Catalyst 2960 series switch.
    Kamil

Maybe you are looking for

  • How do I place a photo in Illustrator from my iPhoto Library?

    I am a graphic designer and I use Illustrator and Photoshop a lot. I don't use iPhoto for most of my photo editing but rather for the organizing it does with my photos in regard to me viewing them. Since updating to iPhoto 08 the other day I am unabl

  • While copying Roll Budget to STAT Budget I am getting error

    Hi Guys I am copying  Roll Budget to STAT  using the e T code YCT02 ( ROLL to STAT budget ) In YCT02 I have entered the below data in the screen . Budget version - 2012010ROLL Budget version Static -2012000STAT Controlling Area u2013 2000 Company cod

  • Cannot back up using Time Machine - MacBook OS X 10.5.8

    Hello there I am having trouble backing up my files using Time Machine. I was using an old external hard disk. When I started using Time Machine, I didn't know about partitioning it. It worked for about 2 years until around the February of this year.

  • CS5 will not start

    Hi Guys.  After running perfectly for months my CS5 will now not start from either the icons or the applications folder.  I've done the following; 1. Uuninstalled it. 2. Deleted all the relevant folders. 3. Run the clean up utility. 4. Rebooted the c

  • Link to OLD Versions of Shockwave Player

    I, like many others, need Shockwave 10 in order to support Windows 2000 installations. However, it's nowhere to be found on an Adobe web site. However, according to a recent message to me in a support case, maybe it will be one day soon: Please refer