Cisco PA's route point problem

I recognize the interceptor point, PA access number which need to setup CTI route point and are assigned with JTAPI user. However, the CTI route point in CCM always show "NOT FOUND". I have checked that the CCM and PA service components are up and running. So, Could anyone advise how I can trace the problem of CTI route point failure?
Thanks a lot.
Note: CCM 4.1(3)sr3b, PA 1.4(3)

Thanks for your reply.
I have checked that several times and still show NOT FOUND.
Belows are the procedures.
1) On CCM, create user with userid = "pauser" and assign the RPs and media ports with it.
2) On PA > telephony, create one Jtapi (userid="pauser") and Skinny profiles.
3) On PA > server configuration, select "Jtapi" profile for items Route Address Provider and Interceptor Port Provider. Add RP number to the route address field....etc
Are there any traces, error logs or troubleshooting guide that I can follow to?
Thanks for help.

Similar Messages

  • Cisco 801 ISDN Router Problem

    Hi at all,
    I need your experience with this device! I will implement a remote connection to a customer.
    Following constellation:
    My PC --> Our ISDN NTBA --> provider --> Phone System customer --> S0 --> ISDN 801 Router --> End Device
    My problem is when I call the phone number with my mobile phone the call takes place, the router brings up the channel and hold this for a few seconds.
    The he kick me out than he can´t speak with my end device.
    When I do this with my remote pc nothing happens only this.
    He hangs up and I must restart this application to do the next attempt. How can I fix this problem?
    The debug isdn q931 shows this:
    00:34:24: ISDN BR0 Q931: RX <- SETUP pd = 8  callref = 0x01
    Sending Complete
    Bearer Capability i = 0x8890
      Standard = CCITT
      Transer Capability = Unrestricted Digital
      Transfer Mode = Circuit
      Transfer Rate = 64 kbit/s
    Channel ID i = 0x8A
    Calling Party Number i = 0x0083, 'xxxxxxx'
      Plan:Unknown, Type:Unknown
    Called Party Number i = 0x80, '69'
      Plan:Unknown, Type:Unknown
    00:34:24: %DIALER-6-BIND: Interface BR0:2 bound to profile Di1
    00:34:103079215104: %LINK-3-UPDOWN: Interface BRI0:2, changed state to up
    00:34:24: ISDN BR0 Q931: TX -> CALL_PROC pd = 8  callref = 0x81
    Channel ID i = 0x8A
    00:34:24: ISDN BR0 Q931: RX <- CONNECT_ACK pd = 8  callref = 0x01
    Channel ID i = 0x8A
    00:34:24: ISDN BR0 Q931: TX -> ALERTING pd = 8  callref = 0x81
    00:34:24: ISDN BR0 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x01
    Cause i = 0x85D1 - Invalid call reference value
    00:34:24: ISDN BR0 Q931: TX -> CONNECT pd = 8  callref = 0x81
    00:34:24: %ISDN-6-CONNECT: Interface BRI0:2 is now connected to xxxxxxxx
    00:34:24: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down
    00:34:24: %DIALER-6-UNBIND: Interface BR0:2 unbound from profile Di1
    00:34:24: ISDN BR0 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x01
    Cause i = 0x85D1 - Invalid call reference value
    00:34:24: ISDN BR0 Q931: L3_Go: L3_GetUser_NLCB returned NULL cid 0x0 cr 0x81 ev 0x5A ces 1 -- Message ignored
    00:34:24: ISDN BR0 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x01
    Cause i = 0x85D1 - Invalid call reference value
    00:34:24: ISDN BR0 Q931: L3_Go: L3_GetUser_NLCB returned NULL cid 0x0 cr 0x81 ev 0x5A ces 1 -- Message ignored
    00:34:27: ISDN BR0 Q931: RX <- DISCONNECT pd = 8  callref = 0x01
    Cause i = 0x8090 - Normal call clearing
    Facility i = 0x91A11302029372020122300AA1053003020100820101
    - ETSI Supplementary Service, Invoke, AOC-D Charging Units: 0
    00:34:27: ISDN BR0 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x01
    And this is my configuration on the Cisco 801 ISDN Router:
    sh run
    Building configuration...
    Current configuration : 1539 bytes
    version 12.3
    no service pad
    service timestamps debug uptime
    service timestamps log uptime
    no service password-encryption
    hostname customer
    boot-start-marker
    boot system flash c800-y6-mw.123-3i.bin
    boot-end-marker
    logging buffered 4096 debugging
    enable secret 5 $1$4sbt$qMDQoozleDqJstTzC2P8I1
    username admin password 7 01000505571F0303
    aaa new-model
    aaa authentication login default local
    aaa authentication ppp default local
    aaa session-id common
    ip subnet-zero
    no ip domain lookup
    isdn switch-type basic-net3
    interface Ethernet0
    description connection
    ip address 192.168.1.254 255.255.255.0
    no keepalive
    interface BRI0
    description connected to Dial-inPC (ISDN)
    no ip address
    encapsulation ppp
    dialer pool-member 1
    isdn switch-type basic-net3
    isdn incoming-voice data
    isdn answer1 12
    isdn send-alerting
    isdn sending-complete
    isdn static-tei 0
    interface Dialer0
    description connected to Dial-inPC (ISDN)
    ip unnumbered Ethernet0
    encapsulation ppp
    no ip split-horizon
    dialer pool 1
    peer default ip address pool test
    no cdp enable
    ppp authentication chap
    ppp multilink
    router rip
    version 2
    network 192.168.1.0
    no auto-summary
    ip local pool test 192.168.1.10 192.168.1.11
    ip classless
    no ip http server
    dialer-list 1 protocol ip permit
    line con 0
    exec-timeout 0 0
    transport preferred all
    transport output all
    stopbits 1
    line vty 0 4
    transport preferred all
    transport input all
    transport output all
    no rcapi server
    end
    I hope anyone have or had this constellation too with a solution that works.
    Many Thanks in advance,
    Mario

    Hi at all,
    We found a solution for this Problem !!
    We always and always got this error:
    %PQUICC-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
    The problem was the cable! The following pin-out is required:
                                            1 ----- 1
                                            2 ----- 2
                                            3 ----- 6
                                            4 ----- 5
                                            5 ----- 4
                                            6 ----- 3
                                            7 ----- 7
                                            8 ----- 8 
    We used this and the fault has disappeared!!
    The only problem that still exists:
    After the first connection the router must be rebooted because otherwise no more additional session is established.
    Thanks for all answers.
    Regards,
    Mario

  • Failed to create the CTI Route Point and corresponding Line on Cisco Unified CM.

    Dear All
               Kindly I got that message "Failed to create the CTI Route Point and corresponding Line on Cisco Unified CM." When I am trying to create Trigger on the UCCX for an Application,
    Bye the way I create Call Control Group and it gives me OK, and I create it from Subsystem>Cisco Unified CM Telephony>Call Control Group
    and Type CTI Ports: 4 | Inbound | Starting DN : 9000 "Nothing in my route pattern report have created CTI numbers"
    So Appreciate your help to avoid that errors raised when I am trying to create new prompts 
    Thanks 
    Ahmed Samir Yosuef 
    Integration Manager

    Let me know the deployment model and Node details

  • Problem with cisco series 800 router and SMTP

    Hello,
    we bought a 877 cisco router and have some problem with SMTP.
    I try to read all forum and KB about but do not find any solution.
    the problem is that when i try to send any email from client (windows mail) i receive a error 533: you need to supply the correct username and password.
    when trying throught hmailserver i receive an email "undeliverable" with this error in body:
    Error Type: SMTP
    Remote server (62.149.128.202) issued an error.
    hMailServer sent: EHLO Globalnet
    Remote server replied: 502 unimplemented (#5.5.1)
    receving email work correctly.
    i'm already using smtp auth, and with my old router everything work fine.
    so i beleive is a config problem, maybe with ESMTP (ehlo)?.
    i attach my config:

    Dear sirs
    Thank you for answer so quickly
    I download this document from Cisco “Configuring the (Remote) Common Application Programming Interface for Cisco 800 Series Router”.
    I have a Lan with Asterisk IP-PBX , the Cisco router have a BRI to public exchange (ISDN) , the router act like a DCP (ISDN- Device Control Protocol) server and listen (DCP messages) in 2578 port.
    I need o know the contents of the TCP frame that carry (ISDN-TCP, the DCP messages) to put a SIP client to talk with PSTN/ISDN using the router. I want to write a software module in Asterisk that translate SIP in (ISDN-DCP) to connect the SIP Phones to the PSTN/ISDN using the BRI ports of the Cisco router. I need to now the contents of this message to dialogue with RCAPI server of the router.
    If forum is the right place perhaps to put this, Could you give me a better place, a mail or other forum to receive the speciation of (ISDN-DCP)
    thank you
    With kinds Regards
    João Pereira Rosa

  • Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command

    Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command
    and I am getting an Error , I cant figure out what I am doing wrong. I have also pasted my display down here can someone help me out, thanks in advance, I am still new to this utility.
    My questions are How do you direct this utility to point to the desktop or the TFTP folder
    does FE_PORT: Fast Ethernet 0 imply or point to Fa0/0 on my router
    My router is suppose to have 10.0.0.3 255.0.0.0
    Gateway of 10.0.0.1 255.0.0.0
    My TFTP Server 10.0.0.2 255.0.0.0
    How do I get the MAC address of the Router or the TFTP Server and which one  is required?
    my Ethernet port is 100Mb/Sec I cant tell whether it is full duplex or not so How do i set this FE_SPEED_MODE: Auto???
    =====================================================================================
    rommon 10 >
    rommon 10 > set
    PS1=rommon ! >
    FE_PORT=0
    WARM_REBOOT=
    RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
    BSI=0
    RET_2_RCALTS=
    RANDOM_NUM=1600357627
    ?=0
    IP_ADDRESS=10.0.0.3
    IP_SUBNET_MASK=255.0.0.0
    DEFAULT_GATEWAY=10.0.0.1
    TFTP_SERVER=10.0.0.2
    TFTP_FILE=
    rommon 11 > TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
    rommon 12 > TFTP_CHECKSUM=0
    rommon 13 > SET
    monitor: command "SET" not found
    rommon 14 > set
    PS1=rommon ! >
    FE_PORT=0
    WARM_REBOOT=
    RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
    BSI=0
    RET_2_RCALTS=
    RANDOM_NUM=1600357627
    IP_ADDRESS=10.0.0.3
    IP_SUBNET_MASK=255.0.0.0
    DEFAULT_GATEWAY=10.0.0.1
    TFTP_SERVER=10.0.0.2
    ?=0
    TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
    TFTP_CHECKSUM=0
    rommon 15 > tftpdnld
              IP_ADDRESS: 10.0.0.3
          IP_SUBNET_MASK: 255.0.0.0
         DEFAULT_GATEWAY: 10.0.0.1
             TFTP_SERVER: 10.0.0.2
               TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
            TFTP_VERBOSE: Progress
        TFTP_RETRY_COUNT: 18
            TFTP_TIMEOUT: 7200
           TFTP_CHECKSUM: No
            TFTP_MACADDR: 30:37:a6:49:35:a8
                 FE_PORT: Fast Ethernet 0
           FE_SPEED_MODE: Auto
    Invoke this command for disaster recovery only.
    WARNING: all existing data in all partitions on flash: will be lost!
    Do you wish to continue? y/n:  [n]:  y
    ARP: address resolution for 10.0.0.2 timed out.
    ARP failed with failure code 1.  TFTP transfer aborted.
    TFTP: Operation terminated prematurely.
    rommon 16 >       " not found
    rommon 17 >FE_SPEED_MODE=2
    variable name contains illegal (non-printable) characters
    rommon
    rommon 18 > set
    PS1=rommon ! >
    FE_PORT=0
    WARM_REBOOT=
    RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
    BSI=0
    RET_2_RCALTS=
    RANDOM_NUM=1600357627
    IP_ADDRESS=10.0.0.3
    IP_SUBNET_MASK=255.0.0.0
    DEFAULT_GATEWAY=10.0.0.1
    TFTP_SERVER=10.0.0.2
    TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
    TFTP_CHECKSUM=0
    ?=0
    rommon 19 > tftpdnld [ur]
    usage: tftpdnld [-hr]
      Use this command for disaster recovery only to recover an image via TFTP.
      Monitor variables are used to set up parameters for the transfer.
      (Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
      "ctrl-c" or "break" stops the transfer before flash erase begins.
      The following variables are REQUIRED to be set for tftpdnld:
                IP_ADDRESS: The IP address for this unit
            IP_SUBNET_MASK: The subnet mask for this unit
           DEFAULT_GATEWAY: The default gateway for this unit
               TFTP_SERVER: The IP address of the server to fetch from
                 TFTP_FILE: The filename to fetch
      The following variables are OPTIONAL:
              TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
          TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=18)
              TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
             TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
              TFTP_MACADDR: The MAC address for this unit
                   FE_PORT: 0= (default), 1
             FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx,
                            5=Auto (default)
          TFTP_DESTINATION: The flash destination device for the file
                            flash:(default), usbflash0:, usbflash1:
      Command line options:
       -h: this help screen
       -r: do not write flash, load to DRAM only and launch image
    rommon 20 > tftpdnld
              IP_ADDRESS: 10.0.0.3
          IP_SUBNET_MASK: 255.0.0.0
         DEFAULT_GATEWAY: 10.0.0.1
             TFTP_SERVER: 10.0.0.2
               TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
            TFTP_VERBOSE: Progress
        TFTP_RETRY_COUNT: 18
            TFTP_TIMEOUT: 7200
           TFTP_CHECKSUM: No
            TFTP_MACADDR: 30:37:a6:49:35:a8
                 FE_PORT: Fast Ethernet 0
           FE_SPEED_MODE: Auto
    Invoke this command for disaster recovery only.
    WARNING: all existing data in all partitions on flash: will be lost!
    Do you wish to continue? y/n:  [n]:  y
    ARP: address resolution for 10.0.0.2 timed out.
    ARP failed with failure code 1.  TFTP transfer aborted.
    TFTP: Operation terminated prematurely.
    rommon 21 >

    What I notice in the original post is this error
    ARP: address resolution for 10.0.0.2 timed out.
    which says that the router is looking for the 10.0.0.2 server but not getting response to its arp request. Can the original poster clarify for us how the device that has the image file is connected to the router that has the problem? Also what kind of device is 10.0.0.2? Is it a PC running TFTP server software or is it something else?
    HTH
    Rick

  • Strange issue - unable to establish PPP with Cisco 887 VAG router on one particular ADSL line

    I have a strange problem that I’m struggling to get to the bottom of with my ISP and wondered if anyone could help.
    We have a site with an older Cisco 877 ADSL router which was working happily until a few weeks ago when the connection dropped suddenly (out-of-hours at 2am if that’s of any significance – made me think most likely something carrier/ISP related?)    When connectivity was lost, the router could sync with the BT exchange (we are in the UK) but could not establish PPP.
    We logged fault with our ISP – after some to’ing and fro’ing, they passed it onto BT and their engineers visited site, they fixed “a line fault” (we don’t get much detail on what was actually fixed) but we still could not establish connectivity – same thing, solid CD light but no PPP.
    So, we replaced the router with another 877 – same again, solid CD but no PPP.  We replaced all the cables and microfilter etc but no difference. 
    We tried a different Cisco router (a newer Cisco 887VAG) which, as I understand, uses a different modem chipset but no matter – PPP could still not be established.  We tested this router on another ADSL line with the same ISP and it worked without issue, using the same ADSL account details, it was able to establish connectivity.  So we figured this must still be a BT/ISP issue.
    Since then we’ve had BT out again twice but they say there is no fault.  The ISP say there is no issue with them.  But we still cannot establish ADSL connectivity on this line, despite having tried 3 different ADSL routers and despite the fact the routers work with the same account details on another ADSL line.
    The 887VAG router we have currently connected has 3G backup so that is keeping us going in the meantime and also means I can login to the router remotely to check on the ADSL status. 
    But I’m struggling to pinpoint where the problem may lie.   Strangely, if I turn on PPP negotiation and authentication debug then I’m not actually seeing any output from it at all?
    Yet, the ATM interface is up and shows packets being sent and received:
    ATM0 is up, line protocol is up
      Hardware is MPC ATMSAR, address is bc16.6596.9b00 (bia bc16.6596.9b00)
      MTU 1600 bytes, sub MTU 1600, BW 704 Kbit/sec, DLY 520 usec,
         reliability 255/255, txload 1/255, rxload 1/255
      Encapsulation ATM, loopback not set
      Keepalive not supported
      Encapsulation(s): AAL5
      4 maximum active VCs, 1024 VCs per VP, 1 current VCCs
      VC Auto Creation Disabled.
      VC idle disconnect time: 300 seconds
      Last input 00:00:28, output 00:00:07, output hang never
      Last clearing of "show interface" counters 6d23h
      Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
      Queueing strategy: Per VC Queueing
      5 minute input rate 0 bits/sec, 0 packets/sec
      5 minute output rate 0 bits/sec, 0 packets/sec
         23886 packets input, 1676964 bytes, 0 no buffer
         Received 0 broadcasts (0 IP multicasts)
         0 runts, 0 giants, 0 throttles
         0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
         56469 packets output, 4418592 bytes, 0 underruns
         0 output errors, 0 collisions, 6 interface resets
         0 unknown protocol drops
         0 output buffer failures, 0 output buffers swapped out
    Does anyone have any ideas on where the problem may be and what more I can do to troubleshoot and provide the relevant evidence to our ISP (assuming it is an ISP/BT issue though the fact the same router works ok with the exact same details etc would seem to indicate it must be their issue!)

    Hi Jody,
    thanks for the suggestions.  Here's what I see from the ppp debugs (but I'm not sure how to interpret?)
    Jan  6 14:50:22.838: pppoe_send_padi:
    contiguous pak, size 74
             00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 FF FF
             FF FF FF FF BC 16 65 96 9B 00 88 63 11 09 00 00
             00 10 01 01 00 00 01 03 00 08 0C 00 00 01 00 00
             04 A3 00 00 00 00 00 00 00 00 00 00 00 00 00 00
             00 00 00 00 00 00 00 00 ...
    Jan  6 14:50:22.878: PPPoE 0: I PADO  R:0030.8810.000b L:bc16.6596.9b00 0/38  ATM0.1
    contiguous pak, size 71
             BC 16 65 96 9B 00 00 30 88 10 00 0B 88 63 11 07
             00 00 00 33 01 03 00 08 0C 00 00 01 00 00 04 A3
             01 02 00 1F 62 72 61 73 2D 72 65 64 37 2E 6C 73
             2D 62 61 73 2D 42 32 32 36 45 34 37 30 39 45 30
             31 34 5A 01 01 00 00
    Jan  6 14:50:24.885: OUT PADR from PPPoE Session
    contiguous pak, size 85
             00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 00 30
             88 10 00 0B BC 16 65 96 9B 00 88 63 11 19 00 00
             00 33 01 03 00 08 0C 00 00 01 00 00 04 A3 01 02
             00 1F 62 72 61 73 2D 72 65 64 37 2E 6C 73 2D 62
             61 73 2D 42 32 32 36 45 ...
    Jan  6 14:50:35.125: OUT PADR from PPPoE Session
    contiguous pak, size 85
             00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 00 30
             88 10 00 0B BC 16 65 96 9B 00 88 63 11 19 00 00
             00 33 01 03 00 08 0C 00 00 01 00 00 04 A3 01 02
             00 1F 62 72 61 73 2D 72 65 64 37 2E 6C 73 2D 62
             61 73 2D 42 32 32 36 45 ...
    Jan  6 14:50:45.364: OUT PADR from PPPoE Session
    contiguous pak, size 85
             00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 00 30
             88 10 00 0B BC 16 65 96 9B 00 88 63 11 19 00 00
             00 33 01 03 00 08 0C 00 00 01 00 00 04 A3 01 02
             00 1F 62 72 61 73 2D 72 65 64 37 2E 6C 73 2D 62
             61 73 2D 42 32 32 36 45 ...
    Jan  6 14:50:55.603: OUT PADR from PPPoE Session
    contiguous pak, size 85
             00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 00 30
             88 10 00 0B BC 16 65 96 9B 00 88 63 11 19 00 00
             00 33 01 03 00 08 0C 00 00 01 00 00 04 A3 01 02
             00 1F 62 72 61 73 2D 72 65 64 37 2E 6C 73 2D 62
             61 73 2D 42 32 32 36 45 ...
    Jan  6 14:51:05.843: OUT PADR from PPPoE Session
    contiguous pak, size 85
             00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 00 30
             88 10 00 0B BC 16 65 96 9B 00 88 63 11 19 00 00
             00 33 01 03 00 08 0C 00 00 01 00 00 04 A3 01 02
             00 1F 62 72 61 73 2D 72 65 64 37 2E 6C 73 2D 62
             61 73 2D 42 32 32 36 45 ...
    Jan  6 14:51:16.114: OUT PADR from PPPoE Session
    contiguous pak, size 85
             00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 00 30
             88 10 00 0B BC 16 65 96 9B 00 88 63 11 19 00 00
             00 33 01 03 00 08 0C 00 00 01 00 00 04 A3 01 02
             00 1F 62 72 61 73 2D 72 65 64 37 2E 6C 73 2D 62
             61 73 2D 42 32 32 36 45 ...
    Jan  6 14:51:26.353: [0]PPPoE 0: O PADT  R:0000.0000.0000 L:0000.0000.0000 0/38  ATM0.1
    contiguous pak, size 74
             00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 00 00
             00 00 00 00 00 00 00 00 00 00 88 63 11 A7 00 00
             00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
             00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
             00 00 00 00 00 00 00 00 ...
    Jan  6 14:51:46.576: pppoe_send_padi:
    contiguous pak, size 74
             00 01 09 00 AA AA 03 00 80 C2 00 07 00 00 FF FF
             FF FF FF FF BC 16 65 96 9B 00 88 63 11 09 00 00
             00 10 01 01 00 00 01 03 00 08 0C 00 00 01 00 00
             04 A3 00 00 00 00 00 00 00 00 00 00 00 00 00 00
             00 00 00 00 00 00 00 00 ...
    Jan  6 14:51:46.608: PPPoE 0: I PADO  R:0030.8810.000b L:bc16.6596.9b00 0/38  ATM0.1
    contiguous pak, size 71
             BC 16 65 96 9B 00 00 30 88 10 00 0B 88 63 11 07
             00 00 00 33 01 03 00 08 0C 00 00 01 00 00 04 A3
             01 02 00 1F 62 72 61 73 2D 72 65 64 37 2E 6C 73
             2D 62 61 73 2D 42 32 32 36 45 34 37 30 39 45 30
             31 34 5A 01 01 00 00
    Provider wouldn't have bumped us from ADSL to VDSL - but here's the output of show controller vdsl 0:
    Controller VDSL 0 is UP
    Daemon Status:           Up
                            XTU-R (DS)              XTU-C (US)
    Chip Vendor ID:         'BDCM'                   'IFTN'
    Chip Vendor Specific:   0x0000                   0x71C8
    Chip Vendor Country:    0xB500                   0xB500
    Modem Vendor ID:        'CSCO'                   '    '
    Modem Vendor Specific:  0x4602                   0x0000
    Modem Vendor Country:   0xB500                   0x0000
    Serial Number Near:    FCZ1111C08V C887VAG 15.2(4)M
    Serial Number Far:
    Modem Version Near:    15.2(4)M
    Modem Version Far:     0x71c8
    Modem Status:            TC Sync (Showtime!)
    DSL Config Mode:         AUTO
    Trained Mode:            G.992.1 (ADSL) Annex A
    TC Mode:                 ATM
    Selftest Result:         0x00
    DELT configuration:      disabled
    DELT state:              not running
    Trellis:                 ON                       ON
    SRA:                     disabled                        disabled
     SRA count:              0                       0
    Bit swap:                enabled                         enabled
     Bit swap count:         1                       8
    Line Attenuation:        54.5 dB                 31.5 dB
    Signal Attenuation:      54.5 dB                  0.0 dB
    Noise Margin:             6.7 dB                 11.0 dB
    Attainable Rate:        2132 kbits/s             888 kbits/s
    Actual Power:            16.7 dBm                12.7 dBm
    Total FECC:             546                      0
    Total ES:               6                        0
    Total SES:              0                        0
    Total LOSS:             0                        0
    Total UAS:              486                      486
    Total LPRS:             0                        0
    Total LOFS:             0                        0
    Total LOLS:             0                        0
    Full inits:             14
    Failed full inits:      1
    Short inits:            0
    Failed short inits:     1
    Firmware        Source          File Name (version)
    VDSL            user config     flash:vdsl.bin-A2pv6C035d_d23j (10)
    Modem FW  Version:      110802_1752-4.02L.03.A2pv6C035d.d23j
    Modem PHY Version:      A2pv6C035d.d23j
    Vendor Version:
                      DS Channel1     DS Channel0   US Channel1       US Channel0
    Speed (kbps):             0             1664             0               704
    SRA Previous Speed:       0                0             0                 0
    Previous Speed:           0             1600             0               736
    Total Cells:              0          2786872             0                 0
    User Cells:               0               68             0                 0
    Reed-Solomon EC:          0              546             0                 0
    CRC Errors:               0                9             0                 0
    Header Errors:            0               10             0                 0
    Interleave (ms):       0.00             8.00          0.00              8.00
    Actual INP:            0.00             1.12          0.00              1.28
    Training Log :  Stopped
    Training Log Filename : flash:vdsllog.bin
    And here's the output from the ATM and dialer interfaces:
    interface ATM0
     no ip address
     ip flow ingress
     no atm ilmi-keepalive
    end
    interface ATM0.1 point-to-point
     ip flow ingress
     pvc 0/38
      pppoe-client dial-pool-number 2
    end
    interface Dialer2
     description OUTSIDE
     ip address negotiated
     ip access-group firewall in
     ip mtu 1492
     ip flow ingress
     ip nat outside
     ip inspect DEFAULT100 out
     ip virtual-reassembly in
     encapsulation ppp
     dialer pool 2
     dialer-group 2
     ppp authentication chap callin
     ppp chap hostname ###removed###
     ppp chap password ###removed###
     no cdp enable
     crypto map dcvpn
    end
    As I say though, config-wise, everything should be correct - the same router works fine on another line (which should also confirm the authentication details are correct - at least in as far as it matches what the ISP have on their RADIUS)
    Any further thoughts?

  • JTapi call transfer / conference from Route Point

    We are developing a simple call distribution application but are having problems completing the call transfer.
    our scenario is:
    Caller A calls RP DN.
    RP Accepts call.
    RP Finds appropriate agent, and places new call to agent.(Call B)
    Agent answers.
    RP Transfers/Conferences A & B A.conference(B)
    But nothing happens and no Exceptions thrown.
    The Route Point is created without media termination.
    What are we missing, does any one have any sample code for this type of call handling.
    Thanks.
    John

    Ahh.. the good old RP limitations. Regardless of whether you do media termination or not, the RP has severe limitations with regards to call control. Transfer and Conference are not supported. Make sure you bug Cisco about that as only together we get this changed.
    Here's what Cisco tells you to do instead: register a bunch of CTI ports, then use the RP as router so it routes the call the first CTI port which in turn does the call handling (the RP does the call routing part just fine including finding the first available CTI port (I suspect the busy trigger needs to be 1 on the line on the CTI Port)).
    Then again, why do you need to accept the call? If instead you'd have the RP route the call the first available agent without answering the call, then you have the traditional RP scenario and the RP will do that just fine (you need to register it for call routing though.. jtrace contains code to do that).

  • CTI route point and CTI ports not registering - UCCX 10.5 and CUCM 10.5 - PARTIAL SERVICE

    I'm trying to integrate CUCM 10.5 and UCCX 10.5.
    For some reason CTI route point and CTI ports are not registering on the CUCM and the status of the UCCX is "PARTIAL SERVICE".
    On the UCCX Cisco Unified CCX Engine is in status "PARTIAL SERVICE" and the Unified CM Telephony Subsystem shows status "OUT OF SERVICE".
    I tried with completely new installation of UCCX twice and got the same result twice.
    But when I tried integrating UCCX 10 with the same CUCM 10.5 from above everything works fine and all the ports are registering right away.
    In all the cases I have done the same configuration.
    The versions of CUCM is 10.5.2.10000-5.
    The version of UCCX is 10.5.1.10000-24.
    The version of UCCX 10 with which it works fine is 10.0.1.11001-37.
    Does anyone have an idea what might be the problem?

    No I haven't. Unfortunately I don't have a 32bit Excel at the moment to try.
    Can you please tell me this: I'm installing a new BE6000 system that came with this problematic version of UCCX (10.5.1.10000-24). I have been testing during the weekend with 3 versions of UCCX:
    -10.0.1.11001-37
    -10.6.1.10000-39 and
    -10.5.1.10000-24
    I got the best results with version 10.0.
    Can I install that version (10.0) in BE6000 instead of the one that came preinstalled (10.5.1)?
    This is my first BE6000 installation and I'm not sure if this is OK?
    I installed a newer version of CUCM than the one that came preinstalled because I hit bug CSCup60269 but I'm not sure If I can go to a lower version for CCX.

  • UCCE 7.5.1 - CTI Route Point and CTI Ports not registering in UCM 7.1

    We are in a middle of a new installation of UCCE 7.5.1. The customer will use it only for Outbound calls. The design is to have on PROGGER and one AW, with a cluster of two CallManagers. All the setup has finished regarding the UCCE. Also, the CallManagers have been configured, regarding the CTI Route Point and the CTI Ports. All of these are associated with the PG USER which is CTI Enabled. Configuration on UCCE has been done, including the DIALER, except for the agents and the campaigns.
    The problem is that the CTI Route Point and the CTI Ports on CallManager are not registering. Is this normal, since the agents and the campaigns have not been configured yet or there is an error somewhere?

    Looks fine.
    Is the Dialer running? Maybe those 30VIP phones the Dialer uses as ports to dial from won't be registered until the Dialer starts.
    But they should also be registered if you start dialogictest over the full set.
    What's the "route point". Who asks for it? Is it a dialed number that runs a script?
    Regards,
    Geoff

  • WiFi only works close to router, DNS fail, Signal Bars present but Safari says no Internet, I've deleted and readded through to reset and full reset, I had no problem with 4.3.2 only 4.3.3 both my iPhone4 and my iPad2. I am now beside router - no problem

    Help
    WiFi only works close to router, DNS fail, Signal Bars present but Safari says no Internet, I've deleted and re-added through to reset and full reset, I had no problem with 4.3.2 only 4.3.3 both my iPhone4 and my iPad2. I am now beside router - no problem, but go 20 metres and WiFi becomes unstable. Only way to get either to work is disable WiFi either as a Hot Spot or turn it off and use the 3G connection. This worked with 4.3 &amp; 4.3.2 what has gone wrong? I raised it at the Apple Store in Belfast as a problem but was told that there was no problem with Apple but I must have a faulty router - yeah - that's a lot of faulty routers, my home, my office, my holiday home, Starbucks, my friends house, my son's house. I've tried all the 'fixes'. I think it is a plan to force us to buy Apple Routers

    Two ways out, I added two more Belkin Access Points in my house in Spain so that I'm not more than 10Mtrs away, (Reinforced Concrete & solar glass 2010)
    I bought 3 Apple Airports, 1 x Extreme and 2 x Express (1 as a hard wired AP, 1 as an extender) for my other house (Brick construction 1930's)
    Everthing now works perfectly, as I said 'an apple plot', so either blast them with signal or visit your nearest apple store.
    Early beta iOS5 (iPad) is also much inproved in Beta 3, I have not had any problem with 'Lion'
    Happy hunting!
    john

  • Bulk insertion of CTI Route points in CUCM

    Hi team,
         Is there any way we can insert bulk number of CTI ROUTE POINT's in Cisco Call Manager. I have seen the option for bulk insertion of phones.But i didn't get any option for creating bulk number of CTI Route Points.
    Can someone please help me on this issue.
    Thanks,
    Sasikumar.

    Hi Gergely,
         Thankyou for responding.
        --> The CUCM is in 10.0 version.
        --> Actually i am pretty new to CUCM so i didn't understand what you mean by look at AXL .Can you please elaborate more.
    Thanks in advance,
    Sasikumar.

  • Router 803 Problem

    Hello, i have a problem with a 803 Cisco Router.
    >
    > This Router has 4 interfaces Ethernet and the IOS only recogniced one
    > Ethernet.
    >
    > I don't know if it could be the IOS or perhaps the router is bad.
    >
    > Sorry for my bad English.
    >
    > Pd: I need a reply as soon as possible
    >
    >
    >
    >
    >
    >
    >
    >
    >
    > Hola, tengo un problema con mi Router cisco 803
    >
    > Este router tiene 4 interfaces ethernet pero una vez dentro del IOS este
    > solo me reconoce una ethernet y 3 puertos BRI.
    >
    > NO se a que sera debido ni si es el router el que esta mal o el IOS.
    >
    > La version del IOS es la c800-nsy6-mw.bin
    >
    >
    >
    > Necesito una reespuesta cuanto antes.
    >
    > Un saludo y gracias

    Hi,
    When you say the router only recognises one interface, do you mean in terms on allowing you to apply an IP address to one Ethernet interface?
    If so this is the correct behaviour as the four Ethernet ports form a hub. You could connect up to four PC's into this hub and set up DHCP on the router giving you a small network or you can connect the router to a switch.
    Also remeber that the ports are 10BaseT so check the speed and duplex settings of the devices you are trying to connect.
    HTH
    PJD

  • Too many errors after upgrading the firmware to 1.0.3.10 on Cisco RV180W wireless router

    My company purchased one Cisco RV180W wireless router few days ago and it worked normal with default firmware version of 1.0.0.30. Today I upgraded the firmware to version 1.0.3.10, the users can still access this router via wired and wireless devices, but on the dashboard I observed two major problems, one is the CPU utilization always shows 100%, another is the more and more errors appearing, on the Syslog Summary panel "Error" log has been up to 625 and is still increasing, there is one message repeatedly displaying in the log, see in below:
    Wed Nov 13 13:55:25 2013(GMT+0800) [rv180w][System][PLATFORM] /pfrm2.0/bin/bwLimitConfig /tmp/system.db 18 dot11STA 100 failed. status=-1
    Who can tell me what does this error message mean and how to elinate this error message ?  also how to deal with 100% CPU utilization ?
    Thanks.

    Hello,
    i have been looking at different VPN routers over the last few weeks and i was very close to buying the RV180W, but then i stumbled across many posts reffering to firmware issues, one issue is that the cpu sits at 100% useage, i just wondered if this is a bug in GUI or is the CPU actually max'd out? has anyone had any resolution into this?
    also the firmware on the emulator is a newer version than is listed on the support page, does anyone know when 1.0.3.14 will be released for download?
    when i buy a new product i like to ensure that the system is fully upto date before its put into use but i obviously dont want to add any performance issues from the ofset due to the CPU useage.
    i also have a could of questions if anyone can help
    the Ipsec VPN, will this work with the Built-in VPN client for apple devices? (New IOS7), i am unable to find a quickvpn application for apple IOS.
    is the site-to-site IPSec VPN also compatible with the Cisco Wvrs4400n router?
    thanks in advance.

  • Netmeeting / h323 behind Cisco 806 SoHo router?

    Searching has not lead me to the knowledge I seek! Anyone know?
    Seeking to accept inbound Netmeeting calls through a Cisco 806 SoHo router, running NAT and firewall featureset.
    I seem to have it running, but I get no video. The connect time seems to take too long as well.
    Code snip if it is of any use:
    ip inspect name myfw h323 timeout 3600
    ip nat inside source static tcp 10.10.10.11 1731 interface Ethernet1 1731
    ip nat inside source static tcp 10.10.10.11 1720 interface Ethernet1 1720
    ip nat inside source static tcp 10.10.10.11 1503 interface Ethernet1 1503
    ip nat inside source static tcp 10.10.10.11 522 interface Ethernet1 522
    ip nat inside source static tcp 10.10.10.11 389 interface Ethernet1 389
    access-list 111 permit tcp any any eq 22
    access-list 111 permit tcp any any eq 389
    access-list 111 permit tcp any any eq 522
    access-list 111 permit tcp any any eq 1503
    access-list 111 permit tcp any any eq 1720
    access-list 111 permit tcp any any eq 1731
    access-list 111 permit udp any any eq 1719
    Any ideas?

    Which Cisco IOS version are you using? Is it by any chance less than 12.0.7T. There is a bug CSCdp37366 in the IOS versions before 12.0.7T with the featureset CBAC due to which the H323 calls dont work properly with no video display. Upgrading the IOS to 12.0.7T and above should help solve the problem.

  • Cisco 881W - ap gui interface problem

    We have a new Cisco 881W wireless router;
    used the CP Express gui interface to perform initial setup;
    router assigned 10.10.10.3 as wireless ap gui interface;
    when entering ap gui the entire screen is blank expect for an "enter" button near bottom;
    clicking on this button does nothing; "error on page" is indicated on IE8 status;
    assigned SSID is not broadcasting

    Hi !!
    im the same problem , but i fix it
    first you must change the IOS version to ap801-k9w7-tar.124-10b.JDA3 ( you can dowload for the cisco web )
    after download the image file you putt this command in the ap exec mode:
    ap#archive download-sw /overwrite /force-reload tftp://x.x.x.x/ap801-k9w7-tar.124-10b.JDA3.tar
    after the files are copied to flash memmory , the routyer boots with the new image ang bug fixed
    its is my configuration working: 
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    Current configuration : 3267 bytes
    version 12.4
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    hostname ap
    enable secret 5 $1$T0Qk$/wKGmrwqo0WcBbvTapaNb.
    no aaa new-model
    dot11 ssid CASIO
       vlan 1
       authentication open
       authentication key-management wpa
       guest-mode
       wpa-psk ascii 7 121A04041B04010132222727
    crypto pki trustpoint TP-self-signed-4051168682
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-4051168682
    revocation-check none
    rsakeypair TP-self-signed-4051168682
    crypto pki certificate chain TP-self-signed-4051168682
    certificate self-signed 01
      3082023A 308201A3 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
      31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
      69666963 6174652D 34303531 31363836 3832301E 170D3131 30383139 31303037
      33385A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
      4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D34 30353131
      36383638 3230819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
      8100B090 26BE5E77 FCB338C0 F54949DB 43EF95C1 61A9C3FA 38AC8BDC 18931195
      B1B1A503 65A71B68 8940639A FB6A6D9B 0F327B09 F5C48ECD 89C1B279 9DC6DC98
      11E5D014 914200BB 7F29CFD1 1CC5FDF0 F3AFE547 4954E2CA 37FC1CEC 60641871
      D9949391 35C958B3 FBA6FBF7 116612FD DFAB9467 478A6E07 0F7B2616 F1204158
      EC510203 010001A3 62306030 0F060355 1D130101 FF040530 030101FF 300D0603
      551D1104 06300482 02617030 1F060355 1D230418 30168014 1120DB6C BE01CDEE
      64A2DB14 FA240B27 D3573B9B 301D0603 551D0E04 16041411 20DB6CBE 01CDEE64
      A2DB14FA 240B27D3 573B9B30 0D06092A 864886F7 0D010104 05000381 81003B69
      8FC11090 E61D3BC1 D04FBDC5 622E8BC6 EB63B9FA C795BB15 BB05F417 CFC51F09
      A8A1971E 7E523203 5A40654D B71623CB A48B193A 101FD1AD 868128E9 91940B71
      5CFDDDD4 856B8170 7700C656 A75443DF DBB60F06 67E37A70 69175B84 24AB0380
      221AAA1D 3EB80465 FD1C1F49 B75B0F1D BC4A82B2 EB2176F2 27F54894 5E94
      quit
    username Cisco password 7 106D000A0618
    username ivan privilege 15 secret 5 $1$eEHQ$Dc.dDfXJz2fBbPIGhH.zg1
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    encryption vlan 1 mode ciphers tkip
    ssid CASIO
    speed  basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
    station-role root
    interface Dot11Radio0.1
    encapsulation dot1Q 1 native
    no ip route-cache
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface GigabitEthernet0
    description  the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
    no ip address
    no ip route-cache
    interface GigabitEthernet0.1
    encapsulation dot1Q 1 native
    no ip route-cache
    bridge-group 1
    no bridge-group 1 source-learning
    bridge-group 1 spanning-disabled
    interface BVI1
    ip address 192.168.10.5 255.255.255.0
    no ip route-cache
    ip http server
    ip http authentication local
    ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    bridge 1 route ip
    line con 0
    no activation-character
    line vty 0 4
    login local
    end
    +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    now you cant acces to ap web gui 
    thanks !!!

Maybe you are looking for