Cisco phone not getting ip address

Hi all ,
Cisco 2950 switch
Phone and dhcp server are in the same default vlan .PC's are getting ip address from dhcp server but not the phone
Thanks

Hi
I can see the mac address has registered on the switch . And i have tried couple of phones , result was same .
Then i did run a packet sniffing using wireshark .
I could see dhcp discover from the phone and offer from the server a couple of times .
i am attaching the dhcp offer part from the wireshark .
And i saw one error also
Error part
Option: (150) TFTP Server Address
Length: 11
TFTP Server Address: 49.48.46.48 (49.48.46.48)
TFTP Server Address: 46.55.49.46 (46.55.49.46)
[Expert Info (Error/Protocol): Option length isn't a multiple of 4]
[Option length isn't a multiple of 4]
[Severity level: Error]
[Group: Protocol]
Option: (255) End
Option End: 255
i don't have any idea about the Tftp server address mentioned above .

Similar Messages

Cisco 891 not getting IP address with DHCP with latest IOS

Hi,
I have a few Cisco 891 routers that are configured as DHCP clients on the WAN interface.
For some reason when I boot the router with a late IOS, the router is not receiving an address.
It works just as expected with the older IOSes.
Any ideas of what changed?
This is how the interface is configured:
interface FastEthernet8
ip address dhcp
no ip redirects
no ip unreachables
no ip proxy-arp
duplex auto
speed auto
no cdp enable
This IOS does not work:
c890-universalk9-mz.154-3.M2.bin
While these do work:
c890-universalk9-mz.150-1.M7.bin
c890-universalk9-mz.151-2.T2.bin
c890-universalk9-mz.152-1.T1.bin
Doing a "show ip interface brief" shows that FastEthernet8 is unassigned with the affected IOS.
With the older IOSes there is an IP address.
I had to downgrade two routers due to this issue, and did not have plenty of time to troubleshoot.
Both of the routers are connected to DSL from the same ISP...
Anyone seen anything like this before?

Add another one to the list.
I have a MacBookPro3,1 that connects to WIFI no problem. It used to connect to ethernet when I originally bought it, however I've been using WIFI exclusively for the past 2 years.
Recently I had a need to connect via ethernet and it wouldn't work at home (apple airport router). I next tried connecting via ethernet at a friends house using a linksys WRT54G, no dice either. I have the computer in the lab today (University Network) and I get the same error. 3 different locations, 3 different routers, all same problem. It used to connect to home and university networks ethernet right away.
IP address assigned is 169.xxx.xxx.xxx - subnet - 255.255.0.0
no other info. It's showing up as connecting to the network, but unable to communicate with DHCP. It does work if I enter all of the information in manually.
At first I thought I had messed something up in networking preferences as I tend to play around with things alot. However I did a complete system format, and fresh install of OSX Lion and I still have the same problem, without any of my meddling around to confuse things.
What gives?

Cisco 3502I Not getting ip address

I just deployed 2 brand new 3502I access points. Ap's are connected to a PoE module on a 4507. Ap's are powering up. The 4507 is configured to hand out ip addresses to the ap's. When I run 'sh cdp nei det', I can see the ap's but they do not have an ip address assignment. Another weird thing is in the output of the command, each ap has two entries. One entry shows gigabit0 and the other gigabit0.1. I have never seen this before. I dont know if this in some way is why the ap's are not getting an ip address. I have 40 other 3502I from 2 yrs ago and no problem. The IOS of the new ap's is 15.2. Anyone have an idea to what may be happening? TIA

I will use the cisco 3750 PoE for further testing. It is close by my office and the cable run is under 200 ft. I used this same switch and port to configure the other 40 3502i ap's. Below is the output of the show power inline fa1/0/12:
H02_3750_PoE#sh power inline fa1/0/12
Interface Admin Oper       Power   Device              Class Max
                            (Watts)
Fa1/0/12 auto   on         15.4    AIR-CAP3502I-A-K9   3     15.4
Interface AdminPowerMax   AdminConsumption
             (Watts)           (Watts)
Fa1/0/12              15.4                 15.4
Here is the output of show power inline from a different 4507:
4507#sh power inline gi1/6
Available:953(w) Used:83(w) Remaining:870(w)
Interface Admin Oper            Power(Watts)     Device              Class
                            From PS    To Device
Gi1/6     auto   on         16.6       15.4       AIR-CAP3502I-A-K9   3
Interface AdminPowerMax   AdminConsumption
             (Watts)           (Watts)
Gi1/6                 30.0                 15.4

Phones not getting IP address via DHCP server on same VLAN

Hello....we have a new series of Cisco SF-200s and one new Cisco SF-300. All switches are operating in layer 2 mode currently. Let's say for all intents and purposes, all ports are in VLAN1....pretty much default setup. There is a fiber backbone between uplink ports...and it is working correctly it appears.
There is a DHCP server allocating addresses 192.168.0.60 thru 192.168.0.79. Subnet mask is 255.255.255.0.
PCs and laptops successfully receive an IP address and can access things.....such as surfing the internet. Tested that from multiple switches....all seems to work just fine.
However, it seems that some newly purchased phones (Digium models) simply will not acquire an IP address like the PCs and laptops do.
Pretty broad question....but just wondering.
Thanks!

Hi Greg,
Might be interesting to goto the following sections of the GUI disable the discovery protocols;
1. Administration>Discovery -LLDP >properties
2. Administration>Discovery -CDP >Management interface
3 Smartports >Properties > Admministrative Auto Smartports is disabled.
the switches are real smart and may pre-empt what you are trying to achieve.
regards dave

IP phone not getting IPv6 address

Hi guys,
I am having trouble with receiving IPv6 address from my 2811 CME router that has been configured as a DHCPv6. Could you please help me what is wrong with my configuration below? Thank you.
Router#sh run
Building configuration...
Current configuration : 2327 bytes
! Last configuration change at 22:52:14 UTC Mon Feb 17 2014
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
no aaa new-model
dot11 syslog
ip source-route
no ip cef
no ip domain lookup
ipv6 unicast-routing
ipv6 cef
ipv6 dhcp pool VOICE
address prefix 2001::/64
vendor-specific 9
suboption 1 address 2001::1
suboption 2 ascii "IP-Phone"
multilink bundle-name authenticated
voice-card 0
crypto pki token default removal timeout 0
license udi pid CISCO2811 sn FHK1213F0HN
redundancy
interface FastEthernet0/0
bandwidth 50
no ip address
duplex auto
speed auto
interface FastEthernet0/0.10
encapsulation dot1Q 10
ipv6 address 2001::1/64
ipv6 enable
ipv6 nd other-config-flag
ipv6 dhcp server VOICE
interface FastEthernet0/1
bandwidth 50
no ip address
duplex auto
speed auto
ip forward-protocol nd
no ip http server
no ip http secure-server
tftp-server flash:SCCP41.9-3-1SR2-1S.loads
tftp-server flash:cnu41.9-3-1ES13.sbn
tftp-server flash:cvm41sccp.9-3-1ES13.sbn
tftp-server flash:dsp41.9-3-1ES13.sbn
tftp-server flash:jar41sccp.9-3-1ES13.sbn
tftp-server flash:term41.default.loads
tftp-server flash:apps41.9-3-1ES13.sbn
tftp-server flash:mk-sccp.jar alias English_United_States/mk-sccp.jar
tftp-server flash:g3-tones.xml alias United_States/g3-tones.xml
control-plane
mgcp profile default
telephony-service
protocol mode dual-stack preference ipv6
max-ephones 5
max-dn 5
ip source-address 2001::1
cnf-file location flash:
load 7941 SCCP41.9-3-1SR2-1S.loads
max-conferences 8 gain -6
transfer-system full-consult
create cnf-files version-stamp Jan 01 2002 00:00:00
ephone-dn 1
number 1000
ephone-dn 2
number 2000
ephone-dn 3
number 7000
ephone 1
device-security-mode none
mac-address 0017.9406.FD55
type 7941
button 1:1
ephone 2
device-security-mode none
mac-address 0016.46F5.F08E
button 1:2
ephone 3
device-security-mode none
mac-address 0017.941D.BE05
type 7941
button 1:3
line con 0
logging synchronous
line aux 0
line vty 0 4
login
transport input all
scheduler allocate 20000 1000
end

Duplicate posts.
Go here: https://supportforums.cisco.com/thread/2267863

Guest users not getting IP address

I am setting up Cisco wireless along with ISE 1.3 for guest wireless. The client is going to use the self-registration portal for guest wireless users. I followed this Cisco doc to configure the self-registration portal:
http://www.cisco.com/c/en/us/support/docs/security/identity-services-engine/118742-configure-ise-00.html
I tested this in my home lab and everything works fine. However, at the client users are not getting IP addresses from the DHCP server. This is the same DHCP server that is used for corporate wireless and if you connect that SSID, you get an IP address. I have looked what I configured at home and the client and everything looks the same. In the back of my mind, I feel something is missing, but I can't figure out what it is.
Edit: Not sure if this makes a difference or not, but they are using a Nexus 5K for their core switch and it hosts the SVI for this network.
Let me know what information you need and I will post it.
TIA,
Dan

Hello,
Some verifications below :
Did you verify if DHCP Proxy is enabled in wlc's wlan interface ? Case DHCP proxy is disabled, did you verify if the ip helper address is enabled in Nexus SVI ?
DHCP Scope is enabled in the DHCP Server or is enabled in the WLC ?
Verify if Trunk in the switch is enabled correctly passing all VLANs to WLANs ?
Verify if ACL to redirect configured in the WLC is allowing DHCP Server and DHCP Client to client receive IP Address and ports 8443 to Cisco ISE and DNS to resolve some address and get access to ISE Portal ?
The scenario is Local Switching or Central Switching ?
Regards

DHCP via Hyper-V VM, Server2012r2 Hyper-V host, clients not getting IP address

You have to authorize a dhcp server as Britv8 says. That's the only way it'll start dishing out leases. That's standard for Windows DHCP server in an AD Domain.
Also there's 0 reason to mention Hyper-V here. The whole point of virtualization is to do hardware level abstraction.

I recently encountered this. Setup:
Initial setup of the system was at a different location from its final destination, with different network equipment (switches) between the two. No teaming is involved, however.
Set up the system at its final destination, with DHCP via a Hyper-V VM (Server2012r2), Server2012r2 Hyper-V host, physical clients on the lan were not getting IP address.
The physical server box has a 4-port Intel Gigabit ethernet card.
I moved the setup (Hyper-V Virtual Switch manager) so that the interface for the DHCP server VM was isntead using one of two built-in Broadcom adapters.
While this topic seemed promising,
http://community.spiceworks.com/topic/251317-hyper-v-vm-not-leasing-ip-s-dhcp
unfortunately, "fiddling about" was not what I was looking for as possible solution.
My notes for the resolution:
Hyper-V system running...
This topic first appeared in the Spiceworks Community

Cisco ISE 1.2, Clients not getting IP address in closed mode

Hello, I am running closed mode on my switchports. I have an issue where some clients come in in the morning, try to login, and will not get network access. I see that this is because they do not get an IP address. I am using MAB for authentication currently. They appear to MAB correctly and get Authorized in ISE, but they do not get an IP. Therefore, they also do not get the DACL of permit ANY. It's like the port gets de-authenticated during the night. Usually when the machine is rebooted it will come up with an IP address. Here is my switchport config...
switchport access vlan 32
switchport mode access
switchport voice vlan 64
logging event link-status
authentication event fail action next-method
authentication event server dead action authorize vlan 32
authentication event server dead action authorize voice
authentication event server alive action reinitialize
authentication host-mode multi-auth
authentication order mab dot1x
authentication priority dot1x mab
authentication port-control auto
authentication periodic
authentication timer restart 600
authentication timer reauthenticate 7200
authentication violation restrict
mab
dot1x pae authenticator
dot1x timeout quiet-period 300
dot1x timeout tx-period 10
dot1x timeout ratelimit-period 300
dot1x timeout held-period 300
service-policy input QoS-Input-Policy
service-policy output QoS-Host-Port-Output-Policy
end

Thanks, here is the requested output of an Unauthorized client. I had to configure authentication open so they could still get access...
SJ5051IDF1#show authen sess int g2/20 d
Interface: GigabitEthernet2/20
MAC Address: d4be.d94f.ab92
IPv6 Address: Unknown
IPv4 Address: 10.42.32.109
User-Name: D4-BE-D9-4F-AB-92
Status: Unauthorized
Domain: DATA
Oper host mode: multi-auth
Oper control dir: both
Session timeout: N/A
Common Session ID: 0A2A000B000034E367D4B998
Acct Session ID: Unknown
Handle: 0x21000508
Current Policy: POLICY_Gi2/20
Local Policies:
Template: DEFAULT_LINKSEC_POLICY_SHOULD_SECURE (priority 150)
Security Policy: Should Secure
Security Status: Link Unsecure
Method status list:
Method State
mab Authc Success
SJ5051IDF1#
SJ5051IDF1#
SJ5051IDF1#show ip access int g2/20
SJ5051IDF1#
SJ5051IDF1#
SJ5051IDF1#show access-list int g2/20
^
% Invalid input detected at '^' marker.
SJ5051IDF1#show access-list ?
<1-2799> ACL number
WORD ACL name
ipc Show access-list config download info
rate-limit Show rate-limit access lists
| Output modifiers
<cr>
SJ5051IDF1#show access-list g2/20
SJ5051IDF1#
SJ5051IDF1#
SJ5051IDF1#

Cisco Flex Connect and users can not get IP Address by WAN

Hello my name is Ivan
I have a wlc 5508 with license base to 50 aps, i use a deployment flex connect. I already registered all my access points, I use web authentication to authenticate users guest, and the service dhcp is in the central site.
My issue is the users in each remote site, can not get an ip address by dhcp from the central site, they can authenticate in the guest ssid, but any users can not get an ip.
The request is passing by the wan in this way
Central Site DHCP - Router WAN - Remote Site - Users with notebooks. I use flex connect central deployment (all the traffic consulting to the wlc) .
perhaps i should use local deploy? The wlc is in the central site.
Can you help me to resolving this issue please? , perhaps any advice?
Regards
Ivan.

Thanks Osita
If I configure Central Authentication and I configure central switching I need to create a dynamic interafce for each remote site and each dynamic interface associated with a different VLAN ID, because I can not associate a single interface dynamic to the same VLAN ID, but in my case the client remote in each remote site have the same network segment with the same VLAN ID with the same SSID for guests. My goal is to configure web authentication with the local DHCP server at each remote site, will this work?.Each remote site have its own server dhcp.
If I configure authentication central authentication with central switching with web authenticacion as I set in my scenario?
My issues are the interfaces dynamics, because I have the same network to the customer guest with the same ID VLan in each remote site
Regards

AP not getting ip address assigned.

Hi all,
I have a problem with my AIR-AP1041N-E-K9, i do not seem to get an ip-address assigned after a reset to factory defaults.
I do see the AP with CDP:
Device-ID: ap
Advertisement version: 2
Platform: cisco AIR-AP1041N-E-K9
Capabilities: TransBridge IGMP
Interface: gi5, Port ID (outgoing port): GigabitEthernet0
Holdtime: 163
Version: Cisco IOS Software, C1040 Software (C1140-K9W7-M), Version 12.4(25d)JA1, RELEASE SOFTWARE (fc1)
Technical Support:
http://www.cisco.com/techsupport
Copyright
Duplex: full
Power drawn: 15000 milliwatts
SysObjectID: 0.0
Addresses:
unknown addres
So that should mean that layer 2 connectivity is fine.
I have the AP connected to a cisco SG300 switch,and assigned switchport trunk allowed vlan's: 1,3,4,8.
Can someone help me?
Regards,
Menno
Message was edited by: Menno Hogenbirk
I also noticed that when i connect to the AP via console-cable, i can see the AP boot up in the console session, but then i do not get a login prompt, but it seems like the AP is responding; if i shutdown the interconnecting link between the switch and the AP, i do see log messages appearing in the console-connection.
I have tried to debug on the Switch, but i need a password, so i can debug, which i do not have.,

Hi, thanks for your reply,
I'm should be getting my ip via DHCP(as i believed that this is the way that the AP searches for an ip, when it has no config yet). The DHCP-server is configured on a cisco 871 router that is connected to the switch, as i found no option to configure it on my switch, which is in layer 3 mode. The DHCP-pool is assigned to the vlan(native) 1 address-range(in this case 192.168.0.x/24). I also have configured a range for my workstations, and here i do get Ip-addresses assigned.
The AP does not connect to a Wireless controller. Also i have checked my inter-vlan routing on my switch, and i have connectivity to all vlans, so i believe my AP should have connectivity to the DHCP-server configured on the router.
Ping-test from switch shows no issues:
Swouter#ping 192.168.0.1
Pinging 192.168.0.1 with 18 bytes of data:
18 bytes from 192.168.0.1: icmp_seq=1. time=0 ms
18 bytes from 192.168.0.1: icmp_seq=2. time=0 ms
18 bytes from 192.168.0.1: icmp_seq=3. time=0 ms
18 bytes from 192.168.0.1: icmp_seq=4. time=0 ms
----192.168.0.1 PING Statistics----
4 packets transmitted, 4 packets received, 0% packet loss
round-trip (ms) min/avg/max = 0/0/0
Message was edited by: Menno Hogenbirk
Problem has been resolved.

Wifi clients not getting IP addresses

Hello Experts,
I have a Cisco 1140 AP, and using express setup I have cnofigured a IP address to it. This AP is connected to our public network and is configured with a public ip address. We want the guest users to connect to Wifi and gain access to Internet.
While the users connect to Wifi, I find their laptops getting IP address in series 169.x.x.x due to which they are unable to get to internet.
Can somebody guide to what all configuration required so that laptops would get ip address?
Thanks
Arvind

Hello George,
I do not have any DHCP server, I want the AP to allocate IP addresses to wifi clients.
Anshul,
Is there any way the AP distribute the IP addresses? I want to have the AP act as an DHCP server and allocate IP address of wifi clients.
If this is not possible in this AP model 1142N, any other Cisco AP model available, which can act as DHCP server?
My requirement basically is:
The AP should allocate IP in the range 192.168.x.x and I would connect the AP to the public network. The wifi clients should be able to get to Internet.
Please suggest any other model in Cisco which should meet my requirement.
Thanks
Arvind

Cisco phone not ringing

Hi Cisco techs,
Cant get my Cisco 7912 phone to ring. Has IP address and switch/router can ping each other
Dial peers are configured. Same as DID and ports. Using CME 3.3.
Have DID number from a VSP. Test call to number goes straight to voicemail after 4 rings
Everything appears to be configured.
Have placed output of common commands in discussion. I eagerly await your ideas. Thanks again
cme_router#sh telephony-service voice-port
voice-port 50/0/1
station-id number 0280070300
station-id name First Last
translate called 1
voice-port 50/0/2
station-id number 1002
station-id name First Last 2
cme_router#
cme_router#sh telephony-service all
CONFIG (Version=3.3)
=====================
Version 3.3
Cisco CallManager Express
For on-line documentation please see:
www.cisco.com/univercd/cc/td/doc/product/access/ip_ph/ip_ks/index.htm
ip source-address 192.168.0.12 port 2000
load 7912 cp7912060000sccp050124a.sbin
max-ephones 4
max-dn 5
max-conferences 4 gain -6
dspfarm units 0
dspfarm transcode sessions 0
hunt-group report delay 1 hours
max-redirect 5
dialplan-pattern 1 02xxxxxxxx extension-length 4 extension-pattern 1001
time-format 24
date-format dd-mm-yy
timezone 0 Greenwich Standard Time
keepalive 30
timeout interdigit 10
timeout busy 10
timeout ringing 180
caller-id name-only: enable
web admin system name admin password xxxxxxxx
web admin customer name Customer
edit DN through Web: enabled.
edit TIME through web: enabled.
Log (table parameters):
max-size: 150
retain-timer: 15
create cnf-files version-stamp 7960 Jun 27 2014 11:39:21
local directory service: enabled.
ephone-dn 1 dual-line
number 1001
name First Last
description Primay Line
preference 0 secondary 9
huntstop
no huntstop channel
translate called 1
call-waiting beep
translation-profile incoming Incoming
translation-profile outgoing Outgoing
ephone-dn 2 dual-line
number 1002
name First Last 2
description Secondary Line
preference 0 secondary 9
huntstop
no huntstop channel
call-waiting beep
Number of Configured ephones 1 (Registered 0)
ephone 1
mac-address 0017.9570.8E67
type 7912
voice-port 50/0/1
station-id number 02xxxxxxxxx
station-id name First Last
translate called 1
voice-port 50/0/2
station-id number 1002
station-id name First Last 2
dial-peer voice 20001 pots
destination-pattern 1001$
huntstop
progress_ind setup enable 3
port 50/0/1
dial-peer voice 20002 pots
destination-pattern 02xxxxxxxx$
huntstop
progress_ind setup enable 3
port 50/0/1
dial-peer voice 20003 pots
destination-pattern 1002$
huntstop
progress_ind setup enable 3
port 50/0/2
tftp-server system:/its/SEPDEFAULT.cnf
tftp-server system:/its/SEPDEFAULT.cnf alias SEPDefault.cnf
tftp-server system:/its/XMLDefault.cnf.xml alias XMLDefault.cnf.xml
tftp-server system:/its/ATADefault.cnf.xml
tftp-server system:/its/united_states/7960-tones.xml alias United_States/7960-tones.xml
tftp-server system:/its/united_states/7960-font.xml alias English_United_States/7960-font.xml
tftp-server system:/its/united_states/7960-dictionary.xml alias English_United_States/7960-dictionary.xml
tftp-server system:/its/united_states/7960-kate.xml alias English_United_States/7960-kate.xml
tftp-server system:/its/united_states/SCCP-dictionary.xml alias English_United_States/SCCP-dictionary.xml
tftp-server system:/its/XMLDefault7912.cnf.xml alias SEP001795708E67.cnf.xml
Have also run sh dial-peer voice if need be...

Thanks for the quick response Carlo
cme_router#sh ephone registered
No ephone in specified type/condition.
cme_router#sh ephone dn 1
Tag 1, Normal or Intercom dn
ephone 1, mac-address 0017.9570.8E67, line 1
cme_router#
cme_router#debug voip ccapi inout
voip ccapi inout debugging is on
cme_router#
HTH

Urgent help? for Standalone AP users are not getting ip addresses

Dear friends,
i have Cisco LAP1140 series access points and i wanted to use them as autonomous , so i converted their ios from light weight to autonomous to
c1140-k9w7-tar.124-25d.JA image.
my network senario is
CORE SW + Access SW + Access points
Core SW:
act as a dhcp server for wireless user
for WLAN vlan 16 is configured on it
configured dhcp pool here for vlan 16
Access SW:
access points are cooneted with it
and every switch port assign to vlan 16 that is connected to AP
Standalone Access Points:
connected to access switch and have assigned static management IPs from vlan 16 that i have excluded in DHCP Pool in core switch.
configure only one ssid and broadcast
both radio 5ghz and 4.2 ghz are up
i can ping the gateway from each Access point to core switch
but the users can not get the ip address from the ssid that is configured on APs.
below is the attached of configuration of the access point
please review the configuration and advise me where i have mistaken and what i have missing in the configuration?
please reply me ASAP because this is very urdent for me and your reply is very important for me
Thanks

Thanks for your reply Ven
actually i did not check that and it does make sence too may be problem with DHCP Scope
but you know why i did not check because there is an other scope on the core switch for Data users only the difference
of vlan numbers and names
but that data vlan users are getting ip addresses and connect normally to internet.
did you view the configuration that i attached with my 1st post?
if no please view it and advise me if i have any missing there.
further i ll check for DHCP in the morning to connect my laptop dirct with switch port to is that getting ip address or no.
Thanks

Bluetooth PAN not getting IP Address (WM5/Samsung Blackjack)

I have a clean Leopard 10.5 install on a MacBook Pro and when connecting to the phone with Bluetooth PAN, an IP Address is not being assigned. I am using a Samsung Blackjack on AT&T with Windows Mobile 5.
I have verified that that Tiger 10.4.10 on the same system, clean install, works as expected and will connect and receive an IP address.
Steps...
1) Pair phone with system
2) On Phone, launch "Internet Sharing"
a) PC Connection should be set to "Bluetooth PAN"
b) Select "Connect"
3) On MacBook Pro, from Bluetooth Menu, select <nameofphone> --> "Connect to Network"
4) Open System Preferences --> Network
5) Notice that "Bluetooth PAN" service is active, but not getting an IP Address
Not sure how to file a bug against Leopard, but hope this will go to the right folks.
Thanks

The Bluetooth PAN is missing from the Network Interfaces.
I had a feeling it was the version of Leopard I was using cause when I tether my PPC phone to my Windows XP machine over Bluetooth it works fine. I used to use my PPC on my Macbook 10.5 when I first got it and loved it. But then I upgraded, sadly. I first experienced this problem when I upgraded my Macbook to 10.5.4. However I recently got another Macbook and I formatted it and put OS X Leopard 10.5 base install on it and it works with it! Why am I now not feeling urged to do any more Apple Updates?
I noticed that with 10.5 you have the choice to add "Bluetooth PAN" and on the the 10.5.4 Apple has removed this option all together! (sounds like a downgrade more than an update...removing a potential Network Interface to use yikes!) The only option in 10.5.4 you have is "Bluetooth" (the one where you have to enter Telephone number, Account Name, Password, the Bluetooth logo) and no Bluetooth PAN...
Here are my available Network devices on my Macbook 10.5 :
Bluetooth PAN
FireWire
Ethernet
Bluetooth
VPN
PPPoE
6 to 4
Here are my available Network devices on my Macbook 10.5.4 :
FireWire
Ethernet
Bluetooth
VPN
PPPoE
6 to 4
See anything missing? So even if I wanted to delete my Existing Bluetooth PAN (which doesn't even work right now anyway) profile I couldn't recreate it because it is not in the list of Network Interfaces! What gives Apple? AT&T got any hands in this?
Message was edited by: Ensilence

Advising record (ADV - HSBC form) in DME file could not get email address

Dear all,
I have problems with DME file that Advising record could not get email that is maintained in vendor master data.
Standard communication methods in vendor master data must be Emails.
We use exit module to get this email for below fields:
Email chnl se. flag
Email address
T-code DMEE -> Advising record
(Attributes tab: Mapping procedures is Exit module.
Source tab: value was entered for Exit function)
We test once and got the expected result: email shown on DME file, in advising record.
However, as I rechecked recently, we have no email shown (though Constant value 'ADV' shown).
The form is active by the way.
I do not know if I miss anything in configuration.
Please advise.
Thank you very much.
Rgds,
Linh

Hello Linh,
Did you manage to resolve this. I'm facing the same problem, not able to get the email address.
Can you please provide the function module you used.
Thanks,
Srini

Cisco phone not getting ip address

Similar Messages

Maybe you are looking for