Cisco PI upgarde from 1.4 to 2.1

Hi all,
I need the information about how to upgarde from PI version 1.4 to the new version 2.1.
Is it possible right now and if not, when will it be possible?
THX!!!

salodh has it correct - 1.4 was always intended for a specific use case and not intended to be an upgradeable release. I doubt an upgrade path will be developed or released.

Similar Messages

WLC IOS upgarde from 4.2.99.0 to 7.0.220.0

Hi
I have an WLC with below details:
Model No:- AIR-WLC4402-50-K9
Current IOS:- 4.2.99.0
Upgrade to :- 7.0.220.0
I wants to upgade WLC with7.0.220.0 IOS. My question is that should i go for direct upgarde from 4.2.99.0 to 7.0.220.0 or is there any IOS version i have to upgarde.

You need to upgrade to
4.2.209.0 before upgrading to 7.0.220.0
Check the following link for more details:
http://www.cisco.com/en/US/partner/docs/wireless/controller/release/notes/crn7_0_220_0.html#wp796579
Please Don't Forget to rate correct answers

Removing Cisco Valet Connector from your computer

Removing Cisco Valet Connector from your computer

I don't think that a wireless adapter can change the settings on the router.
It says connected to the wireless network then it should have some IP address. Check the IP address of that computer when you are not able to access the Internet.
You can also try to assign a static IP address to the computer and see if that makes any difference.

Technical upgarde from ECC5 to ECC6 EHP4

Dear All,
We are having technical upgarde from ECC5 to ECC6 EHP4. I have have some queries as client what need to be check after upgarde.When golive cahke is done what are check list apar from system is up and running.
Please sugegst
Regards,
Kumar

SAP offers a pre-golive check before actual go-live by logging into your system and doing some important checks as per the requirement for technical or functional go-live check...
So, you want SAP to do pre-golive check, just open up the connection between SAP and your sap system, at the same time, a connection from Solman to SAP too..maintaining the connection details in secure area
You have to open a message in component XX-SER-TCC to find out if your installation is scheduled for a Go-Live check which is conducted by SAP and itu2019s partners.
Go-Live Functional Upgrade Analysis u2013 ideally 6 months before Golive u2013 basically checks your hardware requirement , will it be able to accommodate the increase in the functionalities caused by the Go-Live, also some parameter recommendations to fine-tune your system.
Go-Live Functional Upgrade Verification u2013 This is normally 2 months after the Go-live which is to see eu2019thing is fine after the upgrade.
Then you have normal Earlywatch session , each installation is entitled for 2 free earlywatch session in a year, in this performance tuning is done for your system, hardware,memory, I/0 bottlenecks are identified.
Reports of all these sessions carried out by SAP is then sent to you in form a MS-Word document and you can follow the guidelines mentioned and call up SAP or mail the person who has done the session for you for any clarifications.
Usually once a session is scheduled.
SAP will contact you to open the connections for them, so that they can prepare the system before the actual session takes place , in which they see , if SDCC version is good enough so that they can download the data from your system into their internal system on which they carry out the analysis
Refer to https://websmp208.sap-ag.de/earlywatch

After Update Cisco Prime Infrastructure from 1.3 to 2.0 imported floor plans has black background

Hello everybody,
we have updated cisco prime infrastructure from 1.3 to 2.0. When we now import a floor plan (autocad-file, dwg-format), the background from finally image, that is show in prime, is black. Previous imported floor planes has a white background. We also tried to import a previous imported floor plan again, the background is now black. Is there a possibilty to change the background to white? Thanks

Hi,
Look no further, these issues are related to know bugs. It seems that autocad files have multiple issues with PI 2.0, Only feasible way is to convert them to JPGs and import them. Lets hope these will get fixed to the level they where at PI 1.3.
CSCuj63017, PI 2.0 dwg(AutoCAD file) import reports Tailormade is for Demo use only
Symptom:
When dwg files are imported to Prime Infrastructure, they report
"For Demonstration Purposes only
Tailor made software"
Conditions:
Prime Infrastructure - 2.0.0.0.294
Use of dwg (Auto cad) files
Workaround:
None at this time
Further Problem Description:
CSCuj94500, Loading DWG floor maps on PI 2.0 appears in black background
Symptom:
On PI 2.0 when we try to import autoCAD .dwg file to map, the map appears in black background.
Conditions:
On PI 2.0 when we try to import autoCAD .dwg file to map
Workaround:
use 3rd party tool like Draftsight or AutoCAD Trueview to change the file to .jpg and import again to PI, after that the map appear in white background in PI 2.0.
Further Problem Description:
However, the same .dwg file when we imported it to PI 1.3 appear in map with white background.

How to sync clock of Cisco ASA 5505 from NTP Server on internet

Hi there!
i've setup a site, with cisco ASA 5505. It has public ip also.
i want to sync the clock of firewall from on ntp server on internet, or with internal domain controller that is inside LAN.
The firewall has public IP also.
how can i do this?
Regards!

Hello Lasandro,
This should do it!
http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/basic_hostname_pw.html#wp1236530
Looking for some Networking Assistance?
Contact me directly at [email protected]
I will fix your problem ASAP.
Cheers,
Julio Carvajal Segura
http://laguiadelnetworking.com

How do I get rid of an internet service provider (Cisco) that I never wanted but Cisco keeps me from getting online with my own internet service provider?

I have tried to get rid of an internet service provider named "Cisco" that keeps blocking me from getting on the internet. I have no idea how "Cisco" is doing this. I have only one internet service provider that is Not "Cisco" . "Cisco" keeps coming up on the screen to sign in with a password which of course I do not know and do not want. I went into Safari preference to change the settings and found 2 that I do not want. I thought I had gotten rid of this "link sys" but keeps returning and shows that it is locked. How do I get rid of these in my Safari preferences without a password to them. I only want the one internet service provider that I have to be there and not the other two. Thank you so much.

That is the login into the router itself. Most routers, in order to set them up the first time or after a reset or power fail, have this login procedure. You connect to the router login and configure the settings for your use.
Is this a new router or has it been recently reset in some way? As was written above if the router was provided by your isp then contact them for the setup procedures.
If the router is yours (or someone else's in your household) you need to look at the manual that came with it or go to manufactures website for instructions on how to set it up.
regards

Cisco cert xfer from mac to iphone?

anyone know how to export a user cert from the mac version of cisco vpn client software such that it can be added to the iphone configuration?
i can get the cisco vpn client to export the client cert a file. it is just a binary file with no extension by default, and therefore i don't know what format it is in. i tried simply renaming the file as .p12 and .pfx to no avail - or at least i was not able to get the mac keychain to recognize the certs when i did this, which i took to mean they were probably not valid examples of either of those formats.
there are two options when exporting. i can either export the entire certificate chain along with the cert when i export it (or not), and i can assign a password (or not).
if anyone has a successful recipe for doing this, i would appreciate hearing it.

I'm looking for this too. I haven't found any info on what format the Cisco client uses to export a certificate.

Cisco ISE migration from VM to SNS 3415 Appliance

HI Experts,
My customer is running a ISE VM ( os is 1.1.1 ) with base license used only for guest authentication . As per the requirement we need to migrate the existing setup to the ISE hardware (1.2 ).
Can anyone please help me in the best way to do .
I am planning to install a new ISE setup rather than migration but confused regarding the ISE Licensing .
Thanks in advance
Regards
Agnus

Angus,
First and foremost, you must have a current, non-expired license.
The best way to accomplish this is to log in to the Licensing Portal:
https://tools.cisco.com/SWIFT/LicensingUI/Quickstart#
Click on Licenses. Choose the license you would like top transfer to the new 3415 Appliance.
Note that I have selected two licenses, Base and Advanced. You can only select ONE LICENSE at a time. To Re-Host a Base and an Advanced License, you must do this twice.
Then click Actions > Rehost/Transfer...
A new window will appear requesting the information from your new 3415 Appliance (you must have already installed ISE on the appliance):
You can find this information on the new 3415 by going to Administration > Licensing and clicking on the name of your node.
This is all found in the ISE Admin Guide.
http://www.cisco.com/c/en/us/td/docs/security/ise/1-3/admin_guide/b_ise_admin_guide_13/b_ise_admin_guide_sample_chapter_0111.html#concept_E664BCA9F4164C7F8DE590B7C2C4AD99
Please Rate Helpful posts and mark this question as answered if, in fact, this does answer your question. Otherwise, feel free to post follow-up questions.
Charles Moreton

Cisco ASA Upgrade from 7.0(8) to 8.2(1)

Hi, i need to upgrade my 5510 ASA from 7.0(8) to 8.2(1) ( Please note its different query from my last thread)
what i found online is i will have to do this upgrade in sequence, that is
7.0.x -> 7.2.x --> 8.0.x --> 8.2.1
is that correct?
or i will go to 7.1.x first? like this
7.0.x--> 7.1.x -> 7.2.x --> 8.0.x --> 8.1.x--> 8.2.1
Please guide, Also i am assuming, reboot required after every upgrade right?

ok, i found something on another Cisco document. that is what i thought
To ensure that your configuration updates correctly, you must upgrade to each major release in turn. Therefore, to upgrade from Version 7.0 to Version 8.2, first upgrade from 7.0 to 7.1, then from 7.1 to 7.2, and finally from Version 7.2 to Version 8.2 (8.1 was only available on the ASA 5580). "

Upgarde From ECC 5.0 to ECC 6.0

HI ,
My customer is running the E-Recuriting application on ECC5.0. They want to Upgrade this server to ECC6.0
If any one done it ealrier please tell me wht percaution we need to take before upgarding it.
Details of Server
SAP ECC5.0 Basis Release 6.40
Database -> 10.2.0.2.0 (10g)
OS windows 2003 standard edition.
Thanks in advance
GV

Hi,
You are having the database of 10g which is supported by ECC 6.0
You can directly go ahead with the SAP upgrade.
You need to be carefull about the modification adjustments.
Please download the appropriate upgrade guide, depending upon the database and the OS from the below mentioned link
http://service.sap.com/instguides
You would need an S-user id to logon to market place.
Also, go through this link to understand the upgrade and about the modification adjustments (SPDD and SPAU).
https://wiki.sdn.sap.com/wiki/display/HOME/ERP2005+Upgrade.
In case of any specific issues, then please get back.
Hope this helps.
Regards,
Imran

Cisco 1252 upgrade from standalone autonomous to LWAPP

Hi All,
Can somebody please guide me through the process of upgrading Cisco 1252 access point from Autonomous to Light Weight
iam attaching show version log which gives information about current IOS
on the access point & its in standalone mode now.
Any help would be greatly appreciated.
Cheers,
Satish

Hi Satish,
These two great threads discuss the methods to make this conversion;
From Steve, Leo and Charles;
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=General&topicID=.ee6e8b8&fromOutline=true&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc2c5c3/0
From Scott and Steve;
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=Getting%20Started%20with%20Wireless&topicID=.ee7c7c3&fromOutline=true&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc2fd83/0
Hope this helps!
Rob

Cisco Ucs upgrade from 1.4(3m) to 2.1(1a)

hi!!
I need to do an upgrade from 1.4(3m) to 2.1(1a)!
i've 3 chassis 5108 ( 6 fex 2104xp ) with server B200 M2 and B440 M2. i've two Fi 6120Xp in cluster mode.
i've check the prerequisite to upgrade but i've a question about default zoning;
iv'e brocade switch 5300 ( fw v6.4.1 ) attached to Fi 6120xp
i've SAN configured :
i've no other configuration under San Tab.
The documentation says:
"Default Zoning is Not Supported in Cisco UCS, Release 2.1(1a) Onwards.Default zoning has been deprecated from Cisco UCS, Release 2.1(1a) onwards. Cisco has not supported default zoning in Cisco UCS since Cisco UCS, Release 1.4 in April 2011. All storage connectivity that relies on default zoning in your current configuration will be lost when you upgrade to Cisco UCS, Release 2.1(1a) or a later release. We recommend that you review the Fibre Channel zoning configuration documentation carefully to prepare your migration before you upgrade to Cisco
UCS, Release 2.1(1a) or later."
Can i upgrade to 2.1 (

hi!!
I need to do an upgrade from 1.4(3m) to 2.1(1a)!
i've 3 chassis 5108 ( 6 fex 2104xp ) with server B200 M2 and B440 M2. i've two Fi 6120Xp in cluster mode.
i've check the prerequisite to upgrade but i've a question about default zoning;
iv'e brocade switch 5300 ( fw v6.4.1 ) attached to Fi 6120xp
i've SAN configured :
i've no other configuration under San Tab.
The documentation says:
"Default Zoning is Not Supported in Cisco UCS, Release 2.1(1a) Onwards.Default zoning has been deprecated from Cisco UCS, Release 2.1(1a) onwards. Cisco has not supported default zoning in Cisco UCS since Cisco UCS, Release 1.4 in April 2011. All storage connectivity that relies on default zoning in your current configuration will be lost when you upgrade to Cisco UCS, Release 2.1(1a) or a later release. We recommend that you review the Fibre Channel zoning configuration documentation carefully to prepare your migration before you upgrade to Cisco
UCS, Release 2.1(1a) or later."
Can i upgrade to 2.1 (

HT4759 I am using Windows 7 Ultimate OS which is a upgarde from Vista on my laptop with Microsoft Office 2003. I am trying to use ICloud with an IPhone 5 and IPad mini to stream photos but can't do this with my laptop or devices using my Three network. Wh

Can i use my laptop which is running Windows 7 Ultimate upgrade from Vista to stream photos using ICloud. The outlook programme used is 2003 and i my devices are IPad mini and IPhone 5. My problem is that i able to drag pictures into ICloud for it to send to my devices but nothing happens. Why?
I am grateful for any advice.

A hard drive if it has failed will sometimes allow you to boot into windows but may not work completely (Eg: In a scenario, where system partition ;where windows is installed works fine but logical partition of hard drive has gone bad).
On certain conditions, if the hard drive is on verge of failure may/may not respond completely. I would suggest you to run a diagnostics using Seagate Seatools which works on any hard drive irrespective of manufacturer to actually confirm if your hard drive has failed.
Also, any hard drive can fail in spite of it been 1yr old or 1day old as its all manufactured in bulk and most of it comes from China
//Click on Kudos and Accept as Solution if my reply was helpful and answered your question//
I am an HP employee!!

ABAP Queries not available after upgarde from 4.6C to ECC 6.0

Hi All,
We have upgraded from 4.6C to ECC 6.0 version. There is some problem with the ABAP queries. The ABAP queries created in 4.6C were assigned to a Ztcode and now after the upgrade when we execute the Ztcode we are getting the error
that the program does not exist.
I tried to regenerate the code ( a new program name is generated) but there are differences in the selection screen (like the output format etc) between the two versions.
I looked into the relevant SAP notes also but could not find any solution.
Could any of you suggest any ideas to generate abap queries after upgrade?

hi,
Re: SAP version differences 4.5b, 4.6c and ECC6.0
http://help.sap.com/saphelp_47x200/helpdata/en/fc/e3003deddfae4de10000000a114084/frameset.htm
http://help.sap.com/saphelp_scm50/helpdata/en/28/b34c40cc538437e10000000a155106/frameset.htm
http://help.sap.com/saphelp_erp2005/helpdata/en/43/68805bb88f297ee10000000a422035/frameset.htm
Hope this helps.
venkat.

Cisco PI upgarde from 1.4 to 2.1

Similar Messages

Maybe you are looking for