Cisco PIX 501 to Cisco Concentrator 3005 via Remote Access
Hello folks,
I need your help.
We got a Cisco PIX 501 in one location and this pix is configured for pppoe dial out. The pix connects itself to the internet via pppoe client. ping to an offical ip is running well.
So what I want to do is to establish a von tunnel between this pix and a cisco 3005 concentrator.
But I was not successull to establish it.
Here is the pix config. the acl?s are only for testing and will be replaced if it works.
PIX Version 6.3(4)
interface ethernet0 10baset
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password xxx
passwd xxx
hostname PIX-AU
domain-name araukraine.ua
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol ils 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list outside permit ip any any
access-list inside_access_in permit ip any any
pager lines 24
logging on
logging monitor warnings
logging buffered warnings
mtu outside 1456
mtu inside 1456
ip address outside pppoe setroute
ip address inside 192.168.x.x 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm location 192.168.x.x 255.255.255.224 inside
pdm logging warnings 500
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
access-group outside in interface outside
access-group inside_access_in in interface inside
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
aaa authentication ssh console LOCAL
http server enable
http 192.168.x.x 255.255.x.x inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
telnet 192.168.x.x 255.255.x.x inside
telnet timeout 5
ssh 194.39.97.0 255.255.255.0 outside
ssh timeout 5
management-access inside
console timeout 0
vpdn group pppoe_group request dialout pppoe
vpdn group pppoe_group localname [email protected]
vpdn group pppoe_group ppp authentication pap
vpdn username [email protected] password *********
encrypted privilege 15
vpnclient server 212.xx.xx.xx
vpnclient mode network-extension-mode
vpnclient vpngroup vpntest password ********
vpnclient username pixtest password ********
terminal width 80
on the concentrator I created a user pixtest, a group vpntest and I?ve created rules for the network e.g. to which server the users behind the pix will be able to access.
And that?s all.
I could not send you the output either of the pix or concentrator because I did not get an error or a message that the tunnel will be established.
What can be wrong ?
Thanks for the replies
This sample configuration demonstrates how to form an IPsec tunnel from a PC that runs the Cisco VPN Client (4.x and later) to a Cisco VPN 3000 Concentrator to enable the user to securely access the network inside the VPN Concentrator.
http://www.cisco.com/en/US/products/hw/vpndevc/ps2284/products_configuration_example09186a008026f96c.shtml
Similar Messages
-
Cisco Pix 501 - Need help with VPN passthrough
Greetings!
Currently I have a Cisco Pix 501 version 6.3(1) which is in front of my Windows Server 2008 box. I am fairly new to firewalling, especially with the Cisco Pix; I have been able to accomplish some port forwarding for CCTV camera software, etc. but am coming to a standstill attempting to connect a company laptop (Windows 7 Professional) to the server via VPN.
Previously we had another facility which was able to connect through VPN but it has since been removed (and always seemed to not be very stable to begin with - though it was connecting to a Server 2003 box rather than 2008).
I have been through several articles both here and other forums and have attempted several of the proposed fixes. I'm almost sure at this point I've probably opened up more of my firewall then necessary and may have duplicate information attempted to complete this passthrough. My Server 2008 resides at 192.168.1.15, below is what I have thus far. The "crypto map" sections were all completed long before I took over, I believe this is how the old VPN was set up. What I have added since beginning this endevour is the "fixup protocol pptp 1723", the "access-list" entries relating to both pptp and gre, and the "static (inside, outside)" relating to the pptp.
I am still continuously getting an error on the laptop of "800" whenever I try to connect to the VPN. Any help would be greatly appreciated as I am rapidly losing hair attempting to get this situated.
: Saved
PIX Version 6.3(1)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password RysZD25GpRAOMhF. encrypted
passwd 0I6TSwviLDtVwaTr encrypted
hostname Lorway-PIX
domain-name lorwayco.com
fixup protocol ftp 21
fixup protocol ftp 22
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol ils 389
fixup protocol pptp 1723
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
no fixup protocol smtp 25
fixup protocol sqlnet 1521
names
access-list 80 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
access-list 80 permit ip 192.168.1.0 255.255.255.0 192.168.4.0 255.255.255.0
access-list outside_access_in permit icmp any any
access-list outside_access_in permit tcp any any eq 50000
access-list outside_access_in permit udp any any eq 50000
access-list outside_access_in permit tcp any any eq smtp
access-list outside_access_in permit tcp any any eq www
access-list outside_access_in permit tcp host 66.242.236.26 any eq smtp
access-list outside_access_in permit tcp host 208.21.46.12 any eq smtp
access-list outside_access_in permit tcp host 68.59.232.176 any eq smtp
access-list outside_access_in permit tcp any any eq pop3
access-list outside_access_in permit tcp any any eq https
access-list outside_access_in permit tcp any any eq ftp
access-list outside_access_in permit tcp host 68.53.192.139 any eq smtp
access-list outside_access_in permit tcp any any eq ftp-data
access-list outside_access_in permit tcp any any eq 1009
access-list outside_access_in permit tcp any host 192.168.1.122 eq 7000
access-list outside_access_in permit tcp host 192.168.1.122 any eq 7000
access-list outside_access_in permit tcp any any eq 7000
access-list outside_access_in permit tcp any any eq pptp
access-list outside_access_in permit gre any any
access-list 10 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
access-list 20 permit ip 192.168.1.0 255.255.255.0 192.168.4.0 255.255.255.0
access-list 30 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside 74.221.188.249 255.255.255.0
ip address inside 192.168.1.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list 80
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
static (inside,outside) tcp interface 3389 192.168.1.15 3389 netmask 255.255.255.255 0 0
static (inside,outside) tcp interface 50000 192.168.1.160 50000 netmask 255.255.255.255 0 0
static (inside,outside) udp interface 50000 192.168.1.160 50000 netmask 255.255.255.255 0 0
static (inside,outside) tcp interface smtp 192.168.1.15 smtp netmask 255.255.255.255 0 0
static (inside,outside) tcp interface https 192.168.1.15 https netmask 255.255.255.255 0 0
static (inside,outside) tcp interface www 192.168.1.15 www netmask 255.255.255.255 0 0
static (inside,outside) tcp interface pop3 192.168.1.15 pop3 netmask 255.255.255.255 0 0
static (inside,outside) tcp interface 7000 192.168.1.122 7000 netmask 255.255.255.255 0 0
static (inside,outside) tcp interface pptp 192.168.1.15 pptp netmask 255.255.255.255 0 0
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 74.221.188.1 1
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
http server enable
http 192.168.1.0 255.255.255.0 inside
snmp-server host inside 192.168.1.118
no snmp-server location
no snmp-server contact
snmp-server community public
snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
sysopt connection permit-pptp
sysopt connection permit-l2tp
crypto ipsec transform-set lorway1 esp-3des esp-sha-hmac
crypto map lorwayvpn 30 ipsec-isakmp
crypto map lorwayvpn 30 match address 30
crypto map lorwayvpn 30 set peer 66.18.55.250
crypto map lorwayvpn 30 set transform-set lorway1
crypto map lorwayvpn interface outside
isakmp enable outside
isakmp key ******** address 66.18.50.178 netmask 255.255.255.255
isakmp key ******** address 66.18.55.250 netmask 255.255.255.255
isakmp identity address
isakmp nat-traversal 20
isakmp policy 9 authentication pre-share
isakmp policy 9 encryption 3des
isakmp policy 9 hash sha
isakmp policy 9 group 2
isakmp policy 9 lifetime 86400
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh 0.0.0.0 0.0.0.0 inside
ssh timeout 60
console timeout 0
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
terminal width 80
Cryptochecksum:5c7b250c008519fe970262aa3bc28bb5
: endConfig looks good to me.
I would actually upgrade your PIX to the latest version of 6.3.x if you still have access to the software center as this PIX is on its EOL and you are running an extremely old version of code.
If you place your Windows server bypassing the PIX temporarily, I assume you are able to connect to the VPN? -
Cisco Pix 501 / DNS - DNS resolution stops working over time
Hello,
I currently have a Cisco Pix 501 with the configuration listed below. It connects to the public internet via a cable modem and acts as a DCHP server for the local LAN.
When it first turns on, all computers obtain the correct IP settings and can access the internet. Within 10-15 minutes, computers begin to loose access to the Internet. What’s strange is that each computer that lost Internet access can ping the remote address but cannot perform an nslookup. (it shows as Server UnKnown)
The DNS server is 167.206.254.2 which is the external dns server provided by my ISP. I can ping this address but the local computer is unable to use it for domain to ip resolution.
Then network used to have an existing Windows Small Business Server that was a DNS and WINS Server. I ran dcpromo to remove the role of the server and uninstalled dns via add/remove components.
Can someone please help me determine why the computers over time loose the ability to resolve domain names and therefore loose internet access? Can there be some bad DNS entries created? Is there anything I can run on the local computers to further troubleshoot dns errors? Is it possible that the existing Windows SBS server is still running DNS and therefore causing conficts in some way?
One thing to note is that when I reset the Pix 501, everything begins to work again but only for a short time until one by one each computer can no longer resolve domain names. Also, I noticed that once someone connects via VPN and disconnects, one of the local computers looses the ability to resolve DNS.
Cisco Pix Config
PIX# show config
: Saved
: Written by enable_15 at 08:55:56.390 UTC Fri Mar 15 2013
PIX Version 6.3(5)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password chiuzjKkSD33lwEw encrypted
passwd chiuzjKkSD33lwEw encrypted
hostname PIX
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list VPNGROUP_splitTunnelAcl permit ip 192.168.2.0 255.255.255.0 any
access-list inside_outbound_nat0_acl permit ip 192.168.2.0 255.255.255.0 192.168.3.0 255.255.255.128
access-list outside_cryptomap_dyn_30 permit ip any 192.168.3.0 255.255.255.128
access-list ping_acl permit icmp any any
pager lines 24
logging timestamp
logging monitor debugging
logging buffered debugging
logging history debugging
logging queue 0
icmp permit any echo-reply outside
icmp permit any unreachable outside
icmp permit any echo outside
mtu outside 1500
mtu inside 1500
ip address outside dhcp setroute
ip address inside 192.168.2.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool VPN 192.168.3.2-192.168.3.100 mask 255.255.255.0
pdm location 192.168.2.0 255.255.255.0 inside
pdm location 192.168.3.0 255.255.255.0 inside
pdm logging informational 512
no pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_outbound_nat0_acl
nat (inside) 1 192.168.2.0 255.255.255.0 0 0
access-group ping_acl in interface outside
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout sip-disconnect 0:02:00 sip-invite 0:03:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
aaa-server ACS protocol tacacs+
aaa-server ACS max-failed-attempts 3
aaa-server ACS deadtime 10
aaa authentication ssh console LOCAL
aaa authentication telnet console LOCAL
http server enable
http 192.168.2.0 255.255.255.0 inside
http 192.168.3.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto dynamic-map VPNMAP 10 set transform-set ESP-3DES-MD5
crypto dynamic-map VPNMAP 30 match address outside_cryptomap_dyn_30
crypto dynamic-map VPNMAP 30 set transform-set ESP-3DES-MD5
crypto map MYMAP 10 ipsec-isakmp dynamic VPNMAP
crypto map MYMAP client authentication LOCAL
crypto map MYMAP interface outside
isakmp enable outside
isakmp identity address
isakmp nat-traversal 20
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption des
isakmp policy 10 hash md5
isakmp policy 10 group 1
isakmp policy 10 lifetime 86400
isakmp policy 30 authentication pre-share
isakmp policy 30 encryption 3des
isakmp policy 30 hash md5
isakmp policy 30 group 2
isakmp policy 30 lifetime 86400
vpngroup VPNGRP idle-time 1800
vpngroup VPNGROUP address-pool VPN
vpngroup VPNGROUP dns-server 167.206.254.2
vpngroup VPNGROUP wins-server 192.168.2.50
vpngroup VPNGROUP default-domain advancedarthritiscarecenter.local
vpngroup VPNGROUP split-tunnel VPNGROUP_splitTunnelAcl
vpngroup VPNGROUP idle-time 1800
vpngroup VPNGROUP password ********
telnet 192.168.2.0 255.255.255.0 inside
telnet 192.168.3.0 255.255.255.0 inside
telnet timeout 30
ssh 192.168.2.0 255.255.255.0 inside
ssh 192.168.3.0 255.255.255.0 inside
ssh timeout 60
console timeout 0
dhcpd address 192.168.2.2-192.168.2.33 inside
dhcpd dns 167.206.254.2 167.206.254.2
dhcpd lease 7200
dhcpd ping_timeout 750
dhcpd enable inside
username admin password pO9NW1GJpm4IIIFK encrypted privilege 15
username andrew password A340D92MQ0zV0hGs encrypted privilege 15
terminal width 80
Cryptochecksum:aacfb7d8ae07a6075baf8656a724fbecWow...i didn't realize this was possible. I will certainly check the logs tomorrow via the existing thread but just to confirm, is this only true if DHCP is enabled on PIX?
In other words, I managed to work around this issue by applying static IP's to all computers and the internet works just fine. -
Amazon S3 Backup with Cisco PIX 501 Router - slowww
We are in the process of setting up an Amazon S3 network backup of the NAS server we have in our office. We are using a Synology NAS to backup to Amazon s3, and we use a Cisco PIX 501 to secure our network. The backup from the NAS to Amazon is going painfully slow, so I contacted Synology to resolve the issue. After they examined everything, they think the router is filtering outbound traffic, and this is causing the upload to slow down. I was told the upload should happen over HTTP and HTTPS, and I made sure these ports where open through the Access Rules. There are no rules defined in the Filter Settings.
I looked at the settings with the PDM, and I can't find where the filtering would be. Does someone have any insight to what could be happening? I'm not too familiar with the PIX or all the network settings involved.
Thanks!Thank you for your question. This community is for Cisco Small Business products and your question is in reference to a Cisco Elite/Classic product. Please post your question in the Cisco NetPro forums located here:
- Wireless ----> Wireless - Mobility http://forum.cisco.com/eforum/servlet/NetProf;jsessionid=E0EEC3D9CB4E5165ED16933737822748.SJ3A?page=Wireless_-_Mobility_discussion
This forum has subject matter experts on Cisco Elite/Classic products that may be able to answer your question.
THANKS -
IPSEC Tunnel between JUNIPER (SSG 20) and CISCO PIX 501
I have successfully established the IPSEC tunnel with juniper firewall by using cisco Pix 501 (6.3 version). The problem I am facing, I have network layer connectivity but after time interval I am not able to send the traffic on destination IP address on specific port, but can successfully PING the destination IP. On both firewalls the IPs are permitted for all ports.
Dear Mr.
The same problem has occured with me. -
Mac Mini Server - Best Way to Enable Multiple Users to Connect via Remote Access Concurrently?
Hi
Is there a limit on the number of users that can connect simultaneously via remote access to a Mac Mini running Mac Mini Server?If you have the server application on your Mac mini there is an upper limit but it is so high that I wouldn't worry about it. Depending on how you will be using the server and what it will be supporting there is a practical limit based on performance not software. If you reach the limit of satisfactory performance, the solution is adding another Mac mini server.
-
Hi,
We have a customer with a Pix 501(v6.3.4)(PDM v3.02) Firewall.
We can succesfully setup a VPN connection, but the client loses the Internet connection when the VPN connection is up. I found some articles on the Internet about split tunneling, but I cant figure out how to do this.
Can someone please help me out?I suppose 501 is Easy VPN server
Split tunnel says what traffic goes to VPN tunnel if you dont have split tunnel enabled all traffic iis encrypted you need specify with ACL what traffic should be encrypted
check following example whe is ACL 80 used for split tunnel
http://www.cisco.com/en/US/products/sw/secursw/ps2120/products_configuration_guide_chapter09186a0080172787.html#wp1062497
M.
Hope that helps rate if it does -
Cisco pix 501 open port problem
Hi,
I'm running a Pix 501 for Home office and I want to open first ports for my mail client for an outside located server.
But i get following error in the log:
106023: Deny tcp src outside:<ipmailserver>/993 dst inside:<ipoutsideinterface>/1729 by access-group "outside-mail"
here's my basic config:
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password YYYYYY encrypted
passwd YYYYYY encrypted
hostname sunny
domain-name ciscopix.com
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol ils 389
fixup protocol pptp 1723
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
no fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list outside-mail permit tcp any any eq 465
access-list outside-mail permit tcp any any eq 993
pager lines 24
logging on
logging monitor emergencies
logging buffered informational
mtu outside 1500
mtu inside 1500
ip address outside dhcp setroute
ip address inside 192.168.10.254 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 192.168.10.0 255.255.255.0 0 0
access-group outside-mail in interface outside
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
telnet 192.168.10.0 255.255.255.0 inside
telnet timeout 5
ssh 192.168.10.0 255.255.255.0 inside
ssh timeout 60
console timeout 0
dhcpd address 192.168.10.10-192.168.10.39 inside
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
dhcpd enable inside
username stefan password YYYYY encrypted privilege 2
terminal width 80
Cryptochecksum:
: end
[OK]
What's the problem?
Any recommondations for the config anyway?
ThanksThanks Gerhard for the answer, but i don't want to redirect the port to an inside mail server.
I try to connect to an outside mail server with a mail client from an inside pc (who is in the dhcp ip pool, i.e. 192.168.10.22).
to open the ports i added:
access-list outside-mail permit tcp any any eq 465
access-list outside-mail permit tcp any any eq 993
access-group outside-mail in interface outside
but why is there a deny because of the access-group in the log?
106023: Deny tcp src outside:/993 dst inside:/1729 by access-group "outside-mail"
Regards S. -
Cannot login to Cisco Jabber 10.5.1 over Mobile and Remote Access
Hi,
We have deployed sucessfully VCS Expressway-C and VCS Expressway-E with only 1 zone which is "Unified Communication Traversal" and is for Mobile and Remote Access only. VCS-C and VCS-E are communicating and in statuses everything is active and working. Also VCS-C can communicate with CUCM and CUP (both version 10.5).
Problem is when I deploy Cisco Jabber 10.5.1 on computer outside of LAN and without VPN it start communicating with VCS-E, ask me for accepting certificate (we have certificate only intenally generated on Windows CA) and after that it is trying to connect and after few seconds it will tell me that it can't communicate with server.
Did any of you had same problem or can you advice how to troubleshoot? In Jabber logs there is only something like "Cannot authenticate" error message, but when I startup VPN I can authenticate without any problems.
ThanksOn Expressway-C are your HTTP Allow Lists setup properly? By default, and auto discovered CUCM and IMP should be listed via IP and Hostname, but if not, you'll need to insert manually.
Also, you can look at the config file your Expressway-E would be handing out to Jabber via this method.
From the internet, browse to:
https://vcse.yourdomain.com:8443/Y29sbGFiLmNvbQ/get_edge_config?service_name=_cisco-uds&service_name=_cuplogin
Where:
vcse is your Expressway-E hostname (or CNAME/A record)
yourdomain.com is your own domain
The first directory is your Base64 encoded domain name, remove and trailing equal signs (=)
The XML returned is basically the DNS SRV record information available as if internal for _cisco-uds and _cuplogin
TFTP DNS SRV is optional if you configured TFTP in IMP for your Legacy Clients. -
Hi,
I know this is an old firewall but its just a simple firewall I need, my question is this.
I am not getting any internet with my current config, see below:
show conf
: Saved
: Written by enable_15 at 00:52:17.182 UTC Fri Jul 20 2012
PIX Version 6.3(5)
interface ethernet0 auto shutdown
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password PVSASRJovmamnVkD encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname bmi-501-fw-1
domain-name buildmeit.internal
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list allow_ping permit icmp any any echo-reply
access-list allow_ping permit icmp any any source-quench
access-list allow_ping permit icmp any any unreachable
access-list allow_ping permit icmp any any time-exceeded
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside 78.XX.XXX.XXX 255.255.240.0
ip address inside 10.52.100.123 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm history enable
arp timeout 14400
nat (inside) 101 0.0.0.0 0.0.0.0 0 0
access-group allow_ping in interface outside
access-group allow_ping in interface inside
route inside 10.52.0.0 255.255.0.0 10.52.100.123 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout sip-disconnect 0:02:00 sip-invite 0:03:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
http server enable
http 10.52.10.0 255.255.255.0 inside
http 10.52.66.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
telnet timeout 5
ssh timeout 5
management-access inside
console timeout 0
terminal width 80
Cryptochecksum:f8f18bf2b944dddfaf3d83e6c1e1c57c
bmi-501-fw-1#
What am I missing, if I try and ping 8.8.8.8 it times out, any suggestions?Hi, Thanks for the reply, I've managed to sort it now with the following config below:
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
hostname bmi-501-fw-1
domain-name buildmeit.internal
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
access-list PERMIT_IN deny tcp any any
access-list PERMIT_IN deny ip any any
access-list PERMIT_IN deny udp any any
access-list PERMIT_OUT permit tcp any any
access-list PERMIT_OUT permit ip any any
access-list PERMIT_OUT permit udp any any
access-list PERMIT_OUT permit icmp any any
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside XXX.XX.XXX.XXX 255.255.240.0
ip address inside 10.52.100.123 255.255.255.0
global (outside) 1 interface
outside interface address added to PAT pool
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
access-group PERMIT_IN in interface outside
access-group PERMIT_OUT in interface inside
route outside 0.0.0.0 0.0.0.0 XX.XX.XXX.1 1
route inside 10.52.0.0 255.255.0.0 10.52.100.123 1
wr mem
Regards to point 5 where you say devices like this shouldnt be used, I know its an unsupported device but what other reasons should I not be using it, its a good\simple firewall - i'd rather use this than say...........a horrible netgear! -
CVPN 3005 & 3020 : Remote Access Clients frozen during 60 seconds
Good morning,
I'm encoutering an interesting issue on two different CVPN boxes (Cisco VPN 3005 and 3020).
The thing is, when remote clients connect to the VPN gateway using their Cisco VPN client, then cannot reach any of my LAN hosts for about 60 seconds despite log-in procedure has ran fine.
Then, after about 60 seconds (sometimes less), connectivity to my network works well.
While they continuously ping one of my hosts, on the CVPN WebUI, session statistics show 0 in/out encrypted packets.
TCPDump at the back of the CVPN box shows no packets sent to my network (not even arp or whatever).
Is there any option I missed on my configuration to disable this annoying freeze time?
Thanks for helping if any of you has ever solved this.
Best regards,
GaëtanI'm not aware of any such setting to sort of put a delay() function on the clients :)
Try to put the desired Phase 1 profile on the top of the VPNC IKE proposals (Global). Phase 1 Parameters are always negotiated from the global proposals (Regardless of what you put in the Group >>> Ipsec Tab
Regards
Farrukh -
Multicast via Remotes Access VPN (ASA)
Hi all,
I have an ASA 5505 that I would like to use as a head end device for several customers to RA into so they can access our TEST network. The trouble is that the TEST net provides multicast video streams that my clients need to see. I am currently doing this with a Windows Server and Clients via L2TP. How can I do this with the ASA instead? I know IPSEC doesn't support multicast.....can anything be done?Hi,
Currently IPSec / Any connect doesn't support multicast over vpn tunnel. As you have now it is possible through L2TP with L2TP client / ASA / Windows Server or if you have IOS router it can be possible through DMVPN/GETVPN....
Regards
Karthik -
Lync Desktop sharing is not working via Remote Access Server / VPN
Sometimes, few users using RAS (Remote Access Server) / VPN are not able to share desktop.
It is irrespective of other user (from other end) is using VPN or Office wired network.
Note - we have enabled VPN split tunnelling for our environment and the issue is happening after that only.
Also, it is happening with few users not all.
laptop is : HP elitebook 2570p
any resolution ?Hi,
Did these issued users also meet the issue internal the corporation?
1. Please double check if the split tunnel VPN setting configure correctly with the help of the link below:
http://blogs.technet.com/b/nexthop/archive/2011/11/15/enabling-lync-media-to-bypass-a-vpn-tunnel.aspx
2. As the issue only happen for a few users who using VPN, please try to delete Lync user profile and then test again.
3. Please also try to change another computer with the issued Lync account using VPN to test the issue.
4. Please also try to test the issue with Internet network instead of VPN to test the issue again.
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support -
Cisco 871W eZVPN is unable to connect Cisco PIX vpn server
crypto ipsec client ezvpn TEST
connect auto
group Cisco key cisco123
mode client
peer 172.1.1.1
xauth userid mode interfactive
interface FastEthernet4
ip address 10.1.1.1 255.255.255.0
ip access-group 101 in
ip nat outside
crypto ipsec client ezvpn TEST
Internet Vlan1
ip address 192.168.1.1 255.255.255.0
ip access-group 100 out
ip nat inside
crypto ipsec client ezvpn TEST inside
ip route 0.0.0.0. 0.0.0.0 192.168.1.254
ip nat inside source route-map EzVPN1 interface FastEthernet4 overload
access-list 100 permit ip any any
access-list 101 permit ip any any
access-list 103 permit ip 192.168.1.0 0.0.0.255 any
route-map EzVPN1 permit 1
match ip address 103
These are the following commands I applied in my Router, It is able to connect but unable to access any other servers. The same user name & password I tried with the VPN dialer it works on my Laptop. Anything I am missing on the router configuration. The VPN server is Cisco PIX 515E.
Cisco IOS on 871W is 12.3(8)Y121) Isn't your default route supposed to be pointing towards the external interface?
ip route 0.0.0.0. 0.0.0.0 192.168.1.254 ?
2) Can you change the 'mode client' to 'mode network-extension'. Also the PIX will need 'nem enable'.
Have a look at the following (I'm assuming you already have as your config seems to be similar):
http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a0080809222.shtml
For old 6.x code on PIX, have a look at:
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a0080241a0d.shtml
Regards
Farrukh -
PIX 501 and Linksys VPN Router (WRV200)
I have inherited a job where we have a Cisco PIX 501 firewall at one site, and Linksys WRV200 VPN Router on two other
sites. I have been asked to connect these Linksys routers to the PIX firewall via VPN.
I believe the Linksys vpn routers can only connect via IPSec VPN, so i am looking for help on configuring the PIX 501 to allow the linksys to connect with the following parameters, if possible.
Key Exchange Method: Auto (IKE)
Encryption: Auto, 3DES, AES128, AES192, AES256
Authentication: MD5
Pre-Shared Key: xxx
PFS: Enabled/Disabled
ISAKMP Key Lifetime: 28800
IPSec Key Lifetime: 3600
On the PIX i have the PDM installed and i have tried using the VPN Wizard to no avail.
I chose the following settings when doing the VPN Wizard:
Type of VPN: Remote Access VPN
Interface: Outside
Type of VPN Client Device used: Cisco VPN Client
(can choose Cisco VPN 3000 Client, MS Windows Client using PPTP, MS Windows client using L2TP)
VPN Client Group
Group Name: RabyEstates
Pre Shared Key: rabytest
Extended Client Authentication: Disabled
Address Pool
Pool Name: VPN-LAN
Range Start: 192.168.2.200
Range End: 192.168.2.250
DNS/WINS/Default Domain: None
IKE Policy
Encryption: 3DES
Authentication: MD5
DH Group: Group 2 (1024-bit)
Transform Set
Encryption: 3DES
Authentication: MD5
I have attached the VPN log from the Linksys VPN Router.
This is the first time i've ever worked with PIX so i'm still trying to figure the thing out, but i'm confident with CCNA level networking.
Thanks for your help!Hi again,
I believe the pix has a 3des license because of the following parts of the "show version"
Licensed Features:
Failover: Disabled
VPN-DES: Enabled
VPN-3DES-AES: Enabled
This PIX has a Restricted (R) license.
I've tried reconnecting the VPN tunnel with debugging on the PIX and get the output as shown in the attached file "vpndebug.txt"
As for the other show commands they give:
pixfirewall# show crypto isakmp sa
Total : 0
Embryonic : 0
dst src state pending created
pixfirewall# show crypto ipsec sa
interface: outside
Crypto map tag: transam, local addr. 10.0.0.1
local ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.101.0/255.255.255.0/0/0)
current_peer: 10.0.0.2:0
PERMIT, flags={origin_is_acl,}
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest 0
#pkts decaps: 0, #pkts decrypt: 0, #pkts verify 0
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0, #pkts decompress failed: 0
#send errors 0, #recv errors 0
local crypto endpt.: 10.0.0.1, remote crypto endpt.: 10.0.0.2
path mtu 1500, ipsec overhead 0, media mtu 1500
current outbound spi: 0
inbound esp sas:
inbound ah sas:
inbound pcp sas:
outbound esp sas:
outbound ah sas:
outbound pcp sas:
pixfirewall#
Thanks again Daniel, i really appreciate your help on this matter.
Maybe you are looking for
-
IPod touch 2G does not appear on iTunes or My Computer or Finder
i have an iPod stuck on recovery mode and doesn't get recognized by the iTunes and i can't see it on Finder either but it gets charged ... i tried to use it on a PC windows 7 and the pc doesn't even beep when i connect the usb.... i use the most upda
-
Error -5000 and: Error when loading the transcode setting
For a couple of days I've been trying to export my project on a DVD, but on the half way of the transcoding it comes the Error -5000, and then there is such a message, something about the navigation, can't be found etc... I work on a mac OS X, using
-
Dip to Color transition with graphic
I'm using a Dip to Color Dissolve transition between a black screen and a graphic that has colored text with a black background. When using the transition, I get the flash of white color, as intended, but the outline of the graphic is visibile. Dragg
-
Reconciliation account setting with tax category
Hello to you all, I need to create/control some reconciliation account for Vendor/customer. Do anybody of you know if the tax category, for this specific Rec. Acc. is a required / suggested field? ( I do not mean at thecnical level but functional lev
-
I need to know if there is any monitoring softwear for my teenager's phone
Is there a program I can install on my teenager's iphone so I can monitor their activity, chats, texts, etc?