Cisco Pix 515 failover how to know the cause of the fail

Hello All,
We have 2 units 515 in failover configuration.
From the last Thursday we are having problems in our pixs.
The primary unit fail and then the standby works.
We need to know what is the real cause of the problem.
We have configured logging and when we check the syslog messages we can´t find anything important.
Our version is 6.3(5).
Can anybody help us?
If you need more information, please tell me.
Thanks in advance.
Martin.

Hello Gurpreet,
Our failover system is working only with the failover cable, not with netwaork cable.
High CPU is occuring in primary unit. The high cpu usage was after the issue.
One thing, disconnecting for a seconds the cable for interfece "inside" (this cable connects th firewall to our network) the failover runs again ok. We can´t understand it.
Here is the sh interface
Thanks again.
Martin
FWPERIMETRO(config)# sh interface
interface ethernet0 "inside" is up, line protocol is up
Hardware is i82559 ethernet, address is 000b.bef7.56c5
IP address 172.17.4.122, subnet mask 255.255.252.0
MTU 1500 bytes, BW 100000 Kbit full duplex
165844 packets input, 2811391461 bytes, 0 no buffer
Received 947714 broadcasts, 0 runts, 0 giants
1294 input errors, 0 CRC, 0 frame, 1294 overrun, 0 ignored, 0 abort
165698 packets output, 4122450665 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
input queue (curr/max blocks): hardware (128/128) software (128/128)
output queue (curr/max blocks): hardware (128/128) software (971/1189)
interface ethernet1 "internet" is up, line protocol is up
Hardware is i82559 ethernet, address is 000b.bef7.56c6
IP address 195.55.225.98, subnet mask 255.255.255.240
MTU 1500 bytes, BW 100000 Kbit full duplex
20253 packets input, 6232273 bytes, 0 no buffer
Received 1830 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
22281 packets output, 2876208926 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
<--- More --->
input queue (curr/max blocks): hardware (128/128) software (8/128)
output queue (curr/max blocks): hardware (2/115) software (0/1)
interface ethernet2 "failover" is up, line protocol is down
Hardware is i82558 ethernet, address is 00e0.b606.92d7
IP address 192.168.254.253, subnet mask 255.255.255.252
MTU 1500 bytes, BW 10000 Kbit half duplex
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
31 packets output, 320148 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
31 lost carrier, 0 no carrier
input queue (curr/max blocks): hardware (128/128) software (0/0)
output queue (curr/max blocks): hardware (0/10) software (0/1)
interface ethernet3 "dmz-2" is up, line protocol is up
Hardware is i82558 ethernet, address is 00e0.b606.92d6
IP address 195.76.142.185, subnet mask 255.255.255.248
MTU 1500 bytes, BW 100000 Kbit full duplex
1179 packets input, 2703322420 bytes, 0 no buffer
Received 2074 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
720 packets output, 4209917559 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
<--- More --->
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
input queue (curr/max blocks): hardware (128/128) software (1/101)
output queue (curr/max blocks): hardware (0/42) software (0/1)
interface ethernet4 "wandas" is up, line protocol is up
Hardware is i82558 ethernet, address is 00e0.b606.92d5
IP address 10.132.0.18, subnet mask 255.255.255.0
MTU 1500 bytes, BW 100000 Kbit full duplex
164402 packets input, 1499053954 bytes, 0 no buffer
Received 411 broadcasts, 0 runts, 0 giants
267 input errors, 0 CRC, 0 frame, 267 overrun, 0 ignored, 0 abort
159201 packets output, 1116228713 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
input queue (curr/max blocks): hardware (128/128) software (128/128)
output queue (curr/max blocks): hardware (0/128) software (0/49)
interface ethernet5 "dmz" is up, line protocol is up
Hardware is i82558 ethernet, address is 00e0.b606.92d4
IP address 172.23.4.2, subnet mask 255.255.255.0
MTU 1500 bytes, BW 100000 Kbit full duplex
16067 packets input, 942162666 bytes, 0 no buffer
Received 2108 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
<--- More --->
13916 packets output, 494350387 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
input queue (curr/max blocks): hardware (128/128) software (6/79)
output queue (curr/max blocks): hardware (0/65) software (0/1)

Similar Messages

How to know the memory

Hi
Following is the output of sh ver of cisco 2621 router. There is two place saying about the memory
cisco 2621 (MPC860) processor (revision 0x600) with 53248K/12288K bytes of memory.
another
32K bytes of non-volatile configuration memory.
what is the actual memory size? is it 64 or 32?
Can i install an IOS which minimum requires 64Mb memory in this Router?
#sh ver
cisco 2621 (MPC860) processor (revision 0x600) with 53248K/12288K bytes of memor
y.
Processor board ID JAD05440L9D (3776779414)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)

In addition to Andrew info..
How to know the memory ?
cisco 2621 (MPC860) processor (revision 0x600) with 53248K/12288K bytes of memory.
when you get the above output from sh ver,
simply add 53248k + 12288k and always devide by 1024.
e.i
53248k + 12288k / 1024 = 64
64MB is your total memory in your router
Rgds
Jorge

How to know the dynamic values for this :AND category_id_query IN (1, :3, )

Hi Team,
R12 Instance :
Oracle Installed Base Agent User Responsibility --> Item Instances -->
Item Instance: Item Instances > View : Item Instance : xxxxx> Contracts : Item Instance : xxxxx> Service Contract: xxxxx>
In the above page there are two table regions.
Notes.
-------------------------------------Table Region---------------------------
Attachments
-------------------------------------Table Region---------------------------
--the attachments are shown using the query from the fnd_lobs and fnd_docs etc...
I want to know what are the document types are displayed in this page ?
--We developed a custom program to attach the attachments to the services contracts and the above seeded OAF page displays those ..as needed.
But after recent changes..the Attachments--> table region is not showing the attachments.
I have verified the query..and could not find any clue in that..
but i need some help if you guys can provide..
SELECT *
FROM
*(SELECT d.DOCUMENT_ID,*
d.DATATYPE_ID,
d.DATATYPE_NAME,
d.DESCRIPTION,
DECODE(d.FILE_NAME, NULL,
*(SELECT message_text*
FROM fnd_new_messages
WHERE message_name = 'FND_UNDEFINED'
AND application_id = 0
AND language_code = userenv('LANG')
*), d.FILE_NAME)FileName,*
d.MEDIA_ID,
d.CATEGORY_ID,
d.DM_NODE,
d.DM_FOLDER_PATH,
d.DM_TYPE,
d.DM_DOCUMENT_ID,
d.DM_VERSION_NUMBER,
ad.ATTACHED_DOCUMENT_ID,
ad.ENTITY_NAME,
ad.PK1_VALUE,
ad.PK2_VALUE,
ad.PK3_VALUE,
ad.PK4_VALUE,
ad.PK5_VALUE,
d.usage_type,
d.security_type,
d.security_id,
ad.category_id attachment_catgeory_id,
ad.status,
d.storage_type,
d.image_type,
d.START_DATE_ACTIVE,
d.END_DATE_ACTIVE,
d.REQUEST_ID,
d.PROGRAM_APPLICATION_ID,
d.PROGRAM_ID,
d.category_description,
d.publish_flag,
DECODE(ad.category_id, NULL, d.category_id, ad.category_id) category_id_query,
d.URL,
d.TITLE
FROM FND_DOCUMENTS_VL d,
FND_ATTACHED_DOCUMENTS ad
WHERE d.DOCUMENT_ID = ad.DOCUMENT_ID
*) QRSLT*
WHERE ((entity_name    ='OKC_K_HEADERS_V'-- :1
AND pk1_value          IN ( 600144,599046) --:2
AND category_id_query IN (1, :3, :4, :5, :6, :7) )
AND datatype_id       IN (6,2,1,5)
AND (SECURITY_TYPE     =4
OR PUBLISH_FLAG        ='Y')))
--='000180931' -- 'ADP118'
The above seeded query is the one which is used for table region to retrieve the data..
how to know the dynamic values for this : AND category_id_query IN (1, :3, :4, :5, :6, :7) )
--Sridhar

Hi Patricia,
is it working for restricted key figure and calculated key figure ??
Note Number Fisc Period Opening Days
1 1 2
2 1 3
3 1 0
because I have other restriction, so I create two restricted key figure..
RK1 with restriction : Total Number of Note,
RK2 with restriction : Total Opening Days ,
then I Created a calculated key figure, average opening days in a period
CK1 = RK2 / RK1..
in this case, I am not sure if it will work or not..
for example, during RK2 calclation, it might be this   2+3 = 5, the line with 0 will be ignored..
during RK1 calcualtion, it might be 1 + 1 + 1 = 3. ---> Not sure in this case, the line with opening days 0 will be calculated or not..
could you please confirm..

With a contract number, how to know the total PO release value against it?

Usually one contract corresponds to multiple PO records, now we know the contract number, then how to know the total PO release value against this contract. In other word, we would like to know the total release value of all the POs with the same contract number. To just input the contract number in EKPO table? but then look for which field in this table to add these PO release values up?
We will give you reward points!
Thanks!

hi Mohammad,
By following your instruction, input the contract number 4800000112 into Document number field, then hit Enter, get the following (only copy two records here for example), but kind of a mess. Could you let us know which one is the PO release value for this contract?
Contract   Type Vendor     Name                                 PGp Agmt. date
Item Material           Short text                               Mat. group
D I A Plnt SLoc                 Targ.qty. Un       Net price Curr.   per Un
4800000112 WK   2000012012 GULF INTERSTATE FIELD SERVICES       QBH 06/20/2006
Agreement start06/20/2006 Agreement end 12/31/2007
Tgt. val.        1,000,000.00 USD   Open          1,000,000.00 USD   100.00 %
00001                    Inspection Svcs, Construction            R3VNI
L   U                                  0 UL            0.00 USD       1 EA
00002                    Chief Inspector                          R3VNI
L   U                                  0 DAY         390.00 USD       1 DAY

How to know the balance and validity of internet data in iPad

How to know the balance and validity of internet data in iPad?

Sir I m using internet in ipad4 with airtel network
They provide me 2gb data with the amount of 255 rupees
And now I inserted the sim in my ipad4
And start the surfing on safari n all
And now I wanted to know how much data is balance.

How to know the class method behind an enterprise service

Hi,
SAP has provided enterprise services for Room booking in Real Estate module. They are even shipping the complete application for a nominal price. But the standard version is not suitable for our client requirement so they want to develop this application inhouse.
Now my question is: I know the enterprise services used in this application. How to know the implementing methods behind these enterprise services ?
If possible suggest which approach will be a better option for the inhouse development.
1. Webdynpro ABAP and use directly methods behind the enterprise services.
2. Webdynpro ABAP and create client proxy class for the enterprise services.
3. Webdynpro JAVA and use the enterprise services.
4. Using visual composer modelling the application.
Please suggest the best alternative.
Best Regards,
Aleem Mohiuddin.

Hi
They are even shipping the complete application for a nominal price. But the standard version is not suitable for our client requirement so they want to develop this application inhouse.
I assume you are talking about xApps.
How to know the implementing methods behind these enterprise services ?
In sproxy transaction you can search service and then you can see class and method implemented behind that particular service.
1. Webdynpro ABAP and use directly methods behind the enterprise services.
In my opinion not recommended to bypass ES and use method behind it.
2. Webdynpro ABAP and create client proxy class for the enterprise services.
Not sure why you want to create proxy of ES.
3. Webdynpro JAVA and use the enterprise services.
4. Using visual composer modelling the application.
You can use either Webdynpro (ABAP or Java) or VC to model your application which consume ES in backend. Both options are good, you can chose Java or ABAP flavor of dynpro based on skill available in team. VC is very effective in rapid modelling and can be used in protyping or in development of complete application.
Regards,
Gourav

How to know the error in the goods movement

Hai gurus,
a) while doing goods issue and goods receipt , if there is any
error in the goods movement how to know the same and correct it.
Regards,
sekar chand

Hi,
If You are doing GR and GI during order confirmation then you will find a tab for Display Error(Bell Ikon).At the time of any error you will find this icon highlighted.press it you will find details error description and proposed solution.
Regards,
Dhaval

How to know the PO Created with RFQ or Not..??

Hi MM Gurus,
How to know the purchase order created with one quotation or not. because when i am trying to create PO with /ME21N through DOcumen Overview on. there is list of Quotation. i created PO with XYZ quotation. and after creation of PO i am trying to create another PO with another quotation but in that list still XYZ quotation is Displying. so how to knows once PO cretd with Quotation or not. . and I dont wanted to disply quotation once created Po.
Thanks in Advance.
N.A.Reddy

Hi Pradeep. Thanks for the mail.
the problem is ....with *quotation...*
How to know the purchase order created with one quotation or not.
because when i am trying to create PO with /ME21N through DOcumen Overview on. there is list of Quotation.
I created PO with XYZ quotation. and after creation of PO i am trying to create another PO with another quotation but in that list still XYZ quotation is Displying.
so how to knows once PO cretd with Quotation or not. .
and I dont wanted to disply quotation once created Po.
Thanks in Advance.
N.A.Reddy

How to know the count of record in CR XI?

Post Author: Liu ming
CA Forum: Deployment
Hi All,
I create a report by CR XI release 2. The report is viewed in ASP.Net. So, I would like show a message when the report have no record. My question is how to know the count of record?
Thanks.

I was able to do this by using
ora:countNodes('Receive_1_Read_InputVariable','BILL','/ns2:BILL/ns2:CMS1500')

HT204088 How to know the rest of money in a credit card and the total of purchase amount?

How to know the rest of money in a credit card and the total of purchase amount?

What do you mean 'the rest of money in a credit card' ? All you can see on your purchase history is what you've bought, you can't see how things were billed nor the total amount that you've spent in the store - you will need to sum your purchases yourself to see the total.

How to know the timings of the run time of thr report

Hi,
Can you please tell me how to know the run time of the query , i mean how much time it took for the query to dispaly the results .
Also we have these queries in the workbook. How to refresh the work book . is it enough if i refresh the query.
Thanks
Sruthi

Hi
How can we check in RSRT tcode?
And how can we do i RSRTRACE?
Can I know the procedure.

How to know the amount of ora 11g page-out memory (sga and pga)?

How to know the amount of oracle 11g page-out memory ( sga and pga) in the SunSolaris 10 Unix and Linux.
I need to know how many oracle memory are being page-out ( all and for a one oracle server process).
thanks

You can monitor the paging with vmstat or sar commands.
http://download.oracle.com/docs/cd/B28359_01/server.111/b32009/tuning.htm#sthref500
You can also get the paging information on OEM home page if configured for your database.
But I don't know if there exists a method with which one can find out how much memory per session/server process is getting paged out.

How to know the total page number of the standard report

How to know the total page number of the standard report?
If I insert a graph, a table, or text into the end of the standard report, how to know how much space is left for the current page?

Hello Net,
Unfortunately, we do not have any VIs in LabVIEW that can figure out the number of pages of a standard report. However, with the use of ActiveX calls you can achieve this task. Here are a couple of discussion forums which discuss this:
Excel Page Numbering with ActiveX:
http://forums.ni.com/ni/board/message?board.id=170&message.id=194479&requireLogin=False
Number Pages in Word Report:
http://forums.ni.com/ni/board/message?board.id=170&message.id=162972&requireLogin=False
There is also great documentation on using ActiveX on msdn. You can search this document for page number objects. Here is a link to this:
http://msdn2.microsoft.com/en-us/library/aa223048(office.11).aspx
Please refer to these links. If you still have questions please feel free to let us know so we can assist you.
Thank you
Best Regards,
Dominic L.

How to know the run time of a program..?

Hi Gurus,
How to know the exact run time of a program....?
Suppose i've a program....I've changed the code to improve the performance.
Now i want to compare run time of older and new one...How to do this...?
Pls help me ....
Thanks and Regards,
Nagarjuna

Hi,
go thru the below mentioned code............
data:   start TYPE i,
          end TYPE i,
          dif TYPE i.
GET RUN TIME FIELD start.
SELECT SINGLE bukrs belnr gjahr blart budat
FROM bkpf
INTO (cc, doc, fy, doc_ty, pst_dt)
WHERE bukrs = p_bukrs
AND belnr = p_belnr
AND gjahr = p_gjahr.
GET RUN TIME FIELD end.
dif = end - start.
WRITE: /001 'Time for select',
067 ':', dif, 'microseconds'.
Reward all helpful answers.
Thanks

How to know the size of a DATABASE ?

Guys,
How to know the size of a DB ?
Also
How to know the size of a TABLE ?
How to get the content of a procedure/view/trigger ?
Inputs are welcome !

How to know the size of a DB ?If you want to know the physical size, query dba_data_files + dba_temp_files. if you need to know the actual consumed space in those files, compute sum of bytes from DBA_SEGMENTS.
How to know the size of a TABLE ?Query all/dba/user_segments.
How to get the content of a procedure/view/trigger ?all/dba/user_source, all/dba/user_views, all/dba/user_triggers.
Message was edited by:
Satish Kandi

Cisco Pix 515 failover how to know the cause of the fail

Similar Messages

Maybe you are looking for