Cisco Prime 1.2 - same WLANID accross all controllers

Hi,
does anyone know how to achieve to have same WLAN IDs accross all controllers using a WLC Template?
There is no possibility to enter the ID directly.
When I create a WLAN with the same name on WLC before it's not being overwritten and SNMP to device fails.
Thanks for any hints.
K.

Hello,
You can use a CLI template from PI 1.2. It would be the same procedure/commands as configuring the WLAN from the CLI of the controller but using PI to keep them uniform across the WLC's.
It can be found from Design --> Configuration templates --> Controller --> CLI --> General.
Ram

Similar Messages

Cisco Prime Collaboraiton Standard Licenses

Dear Team,
I have a customer purchased Cisco CUWL PRO & Enhanced Licenses for 10,000 Users for Unified CM version 8.0 and now he is asking for upgrade to version 10.5. The question is :
1-since he did reinstatement for different type of licenses and already has the order, Should the customer entitle Cisco Prime Collaboration licenses by default or he has to purchase them separately?
2-Does the customer going to receive Cisco Prime Collaboration Standard (Porvisioning and Assurance only) ?, If so for How many license Users it comes by default?. If less than 10000 ,then how to order the remaining?.
Thanks in advance
Regards,

Prime collaboration standard is free and does not require any licenses. Advanced license is separate from any UC user licenses:
Cisco Prime Collaboration Packaging: Standard and Advanced Options
Beginning with version 10.0, Cisco Prime Collaboration is provided in two different offerings. Cisco Prime Collaboration Standard is included with all Cisco Unified Workspace Licensing and Cisco User Connect Licensing, and Cisco Prime Collaboration Advanced is available for upgrade. The Standard option is only available and compatible with Cisco UC 10.0. The Advanced option supports Cisco UC 8.x - UC 10.x. The Standard option enables provisioning of all voice and video services purchased and fault monitoring across voice and video for a single cluster environment. For deployments that require more advanced management, Cisco Prime Collaboration Advanced offers multi-cluster scale, additional automation, deeper diagnostic capabilities, and long-term reporting. This order guide addresses Cisco Prime Collaboration Advanced only.
Customers who are interested in Cisco Prime Collaboration Advanced may activate the “Advanced Evaluation” from within the Prime Collaboration Standard GUI, for a 60 day term, or may purchase a permanent Cisco Prime Collaboration Advanced. For more information about license installation, please refer to the Cisco Prime Collaboration Quick Start Guide 10.0 posted on Cisco.com under ‘Install and Upgrade Guides.
from:
http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/prime-collaboration/guide-07-729809.html
Chris

SYSLOG Cisco Prime LMS

Hi friends,
I have a question about my syslog from Cisco Prime LMS 4.1, the hours from this syslog in the LMS is diferent from my switch log. I dont kown why.. I verified the hours betewen switch y the Cisco Prime is the same(the LMS is over Windows Server 2008R2) . both are the same log but in diferent hours about 5 hours.
maybe I have to configure the hours for Syslog in the Cisco Prime.
Log from Switch
Log from Cisco Prime LMS

If you have LMS, i am not sure, but if you have PI 1.2. Take a look at my post.
Basically, syslog feature doesn't work well. I could see couple of syslog through event / alarm, but syslog itself is not working properly.
https://supportforums.cisco.com/message/3861981#3861981

HT204074 So a family needs to use the same apple id accross all devices?

If I am understanding this correctly, a family used computer with different log ids will have to use the same apple id. Is this correct?

Welcome to the Apple community.
Only one of your libraries needs to use your iTunes Store Apple ID for home sharing. Your other computers can use their own ID for iTunes, so long as they use the same ID as all of the devices on the network for home sharing.

Cisco Prime 1.2 - cannot delete "Unassigned" Campus

Hi,
has anybody an idea how to delete Unassigned Campus?
I went through I think all documentation and they are speaking that only "System Campus" cannot be deleted, but not a single word about "Unassigned" campus.
All the campuses below behaves like a child of Unassigned campus. I know it's just cosmetic issue, but still I would like to get rid of it.
I attached a screenshot.
Thanks!
K.

Yes you can add building and floor diagrams in Cisco Prime Infrastructure 1.2. For the same you can see the below link
http://www.cisco.com/en/US/docs/wireless/prime_infrastructure/1.2/configuration/guide/maps.html
Open this link and goto Adding Floor Areas to a Campus Building

Cisco Prime Infrastructure 2.0 - no traps/info are pushed from devices

Good evening,
I have setup Cisco Prime Infrastructure 2.0 and, though I have added manually my 4 network cores as devices without any problem, I can't get a single trap or a single SNMP information to be pushed into my Cisco Prime Infra.
Here is my SNMP config on my core :
snmp-server user *edited* *edited* v3
snmp-server group *edited* v3 noauth notify *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF0F
snmp-server community *edited* RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps rf
snmp-server enable traps memory
snmp-server enable traps cpu_threshold
snmp-server enable traps eigrp
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps flex-links status
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps ether-oam
snmp-server enable traps aaa_server
snmp-server enable traps flash insertion removal
snmp-server enable traps l2tc threshold sys-threshold
snmp-server enable traps power-ethernet police
snmp-server enable traps rep
snmp-server enable traps vswitch dual-active vsl
snmp-server enable traps udld link-fail-rpt status-change
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps auth-framework sec-violation
snmp-server enable traps dot1x auth-fail-vlan guest-vlan no-auth-fail-vlan no-guest-vlan
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps entity-diag boot-up-fail hm-test-recover hm-thresh-reached scheduled-test-fail
snmp-server enable traps port-security
snmp-server enable traps ethernet evc status create delete
snmp-server enable traps energywise
snmp-server enable traps ipsla
snmp-server enable traps vstack
snmp-server enable traps bfd
snmp-server enable traps bgp
snmp-server enable traps bulkstat collection transfer
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps isis
snmp-server enable traps msdp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps errdisable
snmp-server enable traps ethernet cfm alarm
snmp-server enable traps vlan-membership
snmp-server enable traps mac-notification change move threshold
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *ip-address-edited* version 3 noauth *edited*
Basically all traps are enabled but absolutely nothing is showing up in my Prime Infra except that my 4 devices are "Reachable".
Here is a show snmp on the same device :
sh snmp
Chassis: *S/N Edited*
38554534 SNMP packets input
    0 Bad SNMP version errors
    14 Unknown community name
    0 Illegal operation for community name supplied
    0 Encoding errors
    38453185 Number of requested variables
    0 Number of altered variables
    17790703 Get-request PDUs
    20583581 Get-next PDUs
    0 Set-request PDUs
    0 Input queue packet drops (Maximum queue size 1000)
38490708 SNMP packets output
    0 Too big errors (Maximum packet size 1500)
    0 No such name errors
    0 Bad values errors
    0 General errors
    38371069 Response PDUs
    13 Trap PDUs
SNMP global trap: enabled
SNMP agent enabled
SNMP logging: enabled
    Logging to *edited*, 0/10, 13 sent, 0 dropped.
Can anyone point out what is wrong or missing in my configuration? I can't seem to single it out myself.
Thanks
Jeremy

Hi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

Cisco Prime 2.1 HA and NFS backup

Hi,
I've just configured my Cisco Prime with the external NFS backup server using instruction from the Administration Guide,
http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-1/administrator/guide/PIAdminBook/backup_restore.html#pgfId-1085464
all works fine but I'm wondering what about HA server? Should I configure all the same steps I did on a primary server?
Regards
Gunter

No, this instruction is for how to configure backup server and how to configure Cisco Prime to be able to use NFS for backup files. It works, I did this and there was no problem during the configuration. The only thing I'm wondering is that I did this on the primary Cisco Prime and not on the HA CP server. So what will hempen if the primary fail and the HA switch over as a primary? Should I configure the same repository on it, should I enable NFS on the HA server also?

Cisco Prime Infrastructure 1.2 and Aironet 1250 + VSS issues

Hi,
I am new to the NCS implementations and configurations. I have one very specific case with Cisco Prime Infrastructure 1.2 and autonomnous APs and several issues with Cisco VSS on 6500 switches.
So here is the version from Prime:
NCS/admin# show version
Cisco Application Deployment Engine OS Release: 2.0
ADE-OS Build Version: 2.0.1.038
ADE-OS System Architecture: x86_64
Copyright (c) 2005-2010 by Cisco Systems, Inc.
All rights reserved.
Hostname: NCS
Version information of installed applications
Cisco Prime Network Control System
Version : 1.2.1.012
IOS version on our APs (which are autonomnous) is:
AP-N-1>show ver
Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(25d)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 11-Aug-11 03:23 by prod_rel_team
Well the issue what we have now is that access point has been added but its not recognized by the NCS prime. I have tried all three versions of SNMP but I get the same result. The SNMP configuration is valid since I use the same for my switching infrastructure. When I enter "debug snmp packets" and "terminal monitor" I can see the SNMP communication between Prime and Aironet 1250 which is standalone.
When I switch to Lifecycle theme and go to Operate > Device Monitor Center I see all devices I have added. The Aironet 1250 is reachable but under collection status I get Managed with Warnings. When I hover over with my mouse I get "None available".
I have successfully added my switching infrastructure in total, which is operating perfectly for Catalyst 2960/3650/3750/4500 series but for 6500 under VSS I have some warnings. The device is recognized by the system which is excellent and all is operational. I get the following errors under Collection Status:
feature_sensor
SNMP request timed out
feature_powerSupplyFanStatus-6k
SNMP request timed out
IdentityCapability
The device is unreachable.
feature_flashdevice
SNMP request timed out
sam_ipsla_feature
The device is unreachable.
What can be done to resolve these issues ? I have attached a screenshot of this particular issue. The affected access point is 172.16.165.241.
Predrag Petrovic

Hi rajeeshp,
Currently I am not allowed to upgrade it because of internal procedures involved in upgrading a specific piece of software (obtaining permissions from various departments). Is it free to upgrade from 1.2 to 1.3 or there is a specific charge for that.
Predrag Petrovic

Cisco Prime Infrastructure MESH LINK ISSUE

Hi,
a Customer of us has a trouble with cisco Prime Infrastructure 1.2.0.12 and AP mesh link.
There is an huge database ( i suppose the issue can be here ) and when we display some map ( each floor has about 6 RAP and 24 MAP ) we cannot see the MESH information and link draw.
The only way to dipley them is to disable "refresh from network": this way I'm able to show these link..... until a click before.
What i noticied when all was working fine, after i click to some floor:
1) the software started to show the map with normal color and no mesh info displayed ( just ap and coverage cloud )
2) after few time ( less than 1 second ) the map was becoming a little bit lighter and the mesh info was merged to the map
We are missini the second step
Anyone had the same issue ?
best regards
Luigi
PS: I opened a case with WCS version 6.0 ( same issue ) but, after some months, no risult. The last version working fine was WCS 5.2

Just to add some more informations:
- disabling "refreshj from network" ( building properties ) the link and mesh info are showed
- while I'm on a floor, after some refresh, i loose the mesh link draw and, if i click on an AP, i loose also mesh info in the popup. It' s like, after some refresh, the AP are no more recognized as Mesh ( !?!? )
regards
Luigi

Cisco Prime Demo

Hi all,
I download Cisco Prime Express 2.1 from www.cisco/go/prime-demo the trail version . the file saved as zip file. when i try to open or extract , it didn't open and show this massage :
Cannot open file ; it does not appear to be a valid archive.....
I download it couple of times from my laptop and my team but same massage appear . can some one help please.

Wrong section to post this question. Check if you are going via proxy or firewall for download. Check your extracting tool works correctly.

Cisco Prime 1.2 (MAPS/FLOOR PLANS)

Hi All,
Does anyone have any idea on how to import and scale correctly campus, building and floor diagrams into Cisco PI?
I have tried several times via the editor to rescale and it just doesn't work.
Any advise would be greatly appreciated.
Thanks in advance for any replies.
Jason

Yes you can add building and floor diagrams in Cisco Prime Infrastructure 1.2. For the same you can see the below link
http://www.cisco.com/en/US/docs/wireless/prime_infrastructure/1.2/configuration/guide/maps.html
Open this link and goto Adding Floor Areas to a Campus Building

Cisco Prime Infrastructure 1.2 OVA not found

Hi all,
I want to download Cisco Prime Infrastructure 1.2 OVA but I can't find it, there is just "Cisco Prime Infrastructure 1.2 Plug and Play for Virtual Appliance " . Is this the right OVA ?
Thanks for your help
BR
Aaziz

Hi Aaziz,
Unfortunately this download of this file is not available anymore on cisco.com site.
As an alternative, you can download PI 1.3 OVA, where you can find the same features and
interface:
http://software.cisco.com/download/release.html?mdfid=284652876&softwareid=284272932&relea
se=1.3&relind=AVAILABLE&rellifecycle=&reltype=all
Note: you can use the same license of PI 1.2 on PI 1.3
Thanks-
Afroz
***Ratings Encourages Contributors ***

Cisco Prime Infrastructure 2.0 Alarms (switch port down)

We have a cisco Prime Infrastructure 2.0 managing switches, routers and AP.
By default, when a port of a switch goes down, the cisco Prime Infrastructre generates a Critical Alarm for that. (this is a problem, because every phone of laptop disconnection will generate a critical alarm for me)
I found out that if we go to Administration --> Alarm Severity --> Link down, I can change the Alarm from Critical to another type of alarm.(ex: warning)
The problem is that I want to keep the Critical Alarm for my Uplinks ports and for some important switch ports, and I would like to make the alarm as warning for the normal user ports.
I know that I can create Port Groupping and add ports to each group and apply monitoring templates on those groups. But This couldn't Help me solving my alarm problem.
So I just need to know how to manage the alarms severity for each group of ports.
Thank you

Hi,
Same problem here.
I am using Cisco Prime Infrastructure 2.0 (evaluation version for 60 days). I want to deploy port monitoring for my trunk ports between switches and some other important ports e.g. servers. Basically I want to get alarms when these ports are down, there are errors on ports and etc.
So in Design>Port Grouping I created User Defined group with important ports. In Deploy>Monitoring Deployment I selected Interface Health (default)>Deploy selected Port Groups and when selected port group I created.
Now the rule shows Deployed: Yes and Status: Active. After that I just pulled out one port which was in monitored group, waited 5min as it is set in Interface Health (default) template, and nothing happened, and worse, alarms started to show up of other ports where regular users are connected (computers was turned off), which I do not want to see at all. I tried redeploy template, I even created my own template but still no desired result.
Any suggestions how to make port monitoring work?

Cisco Prime infrastructure 1.2.1.012 -- HA issue

Hi All
I will explain the background before, our customer using Cisco Prime Infrastructure 1.2.1.012 and do HA. However I got error message wcss1 (in attaced file) from HA configuration. (First I had done HA configuration before and it worked. But I get error message wcss1 after i tested failover on cisco prime). I found bug case CSCud12229 that is same error message. But i still confuse with work around "Workaround:Change the database mode to Read-Write by executing query ?alter database open? or execute the shell script - /opt/CSCOlumos/bin/recover_HADeadLock.sh" anyone understand please help.
And another option I tried to upgrade with version 1.3 also but it have a bug no CSCud80157. It is the problem with HA registration fial so, i would like to ask you all that if i need to do HA on Cisco Prime infrastructure which version i should to install ? coz I saw 1.2 or 1.3 also have a bug with HA
Thanks
V

Hi rajeeshp,
Currently I am not allowed to upgrade it because of internal procedures involved in upgrading a specific piece of software (obtaining permissions from various departments). Is it free to upgrade from 1.2 to 1.3 or there is a specific charge for that.
Predrag Petrovic

WCS and LMS to Cisco Prime Infrastructure 1.3 Upgrade

Hello,
Our customer is currently having WCS for 500 devices and LMS 3.2 for 1500 devices. We are planning to upgrade to Cisco Prime Infrastructure 1.3.
I want to check is the upgrade procedure that we have planned is ok or we have missed something.
Phase 1: WCS to CPI 1.3 upgrade
1. Check that WCS is at 7.0.230.0 version
2. Export WCS database
3. Install NCS 1.1.1.24 software
4. Contact cisco to obtain trial license for NCS software (L-WCS-NCS1-M-K9 license).
5. Migrate WCS license and import it in NCS software
6. Migrate WCS data to NCS software using ncs migrate command
7. Patch NCS software
8. Inline upgrade to CPI 1.3 software
9. Install proper licenses on CPI 1.3 (WCS and LMS device count)
My concern in this first phase is should I use NCS large image since our Cisco Prime Infrastructure 1.3 software should manage 2000 devices at the end.
Or is it better not to perform inline upgrade and insted go with exporting data from NCS and then importing them to CPI 1.3 that is going to be installed separately?
Phase 2: LMS 3.2 to CPI upgrade
1. Export LMS 3.2 database
2. Install LMS 4.2 software
3. Install license to LMS 4.2
4. Restore data from LMS 3.2 to LMS 4.2
5. Direct upgrade from LMS 4.2 to 4.2.2
6. Export the device list with credentials from LMS 4.2.2 and import it as a Bulk Import in CPI 1.3
At the end we will have CPI 1.3 and LMS 4.2.2 software running.
Is it possible to directly upgrade from LMS 4.2 to LMS 4.2.4 and then import data to CPI 1.3 or we need to go with 4.2.2 version?
Regards,
Jelena

Hello Marvin,
We have restored LMS 3.2 SP 1 database on LMs 4.2 and we have got some error messages during restore. Please see our restore output:
[kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/res
resolver.pl           restoreDBTableMig.pl restoreJRMMig.pl      restorebackup.pl
[kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/restorebackup.pl -d /opt/BKP/
Restore started at : 2013/12/05 14:11:58
Please see '/var/adm/CSCOpx/log/restorebackup.log' for status.
     USER ID is ..................................... : sysadmin
     OS of the backup archive is..................... : Windows
INFO:The backup archive is from a different OS. Your current Platform is: Soft Appliance .
You are attempting to perform a Cross Platform Restore..
Do you wish to continue (Y/N) [Y] :Y
     Generation to be restored is ................... : 0
     Backup taken from............................... : /opt/BKP/
     Common Services version in the backup data is... : 3.3.1
     Common Services is installed in................. : /opt/CSCOpx
     The temp folder for this restore program........ : /opt/CSCOpx/tempBackupData
     Applications installed on this machine ......... : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][cwportal][ipm][upm][cvw][cwlms]
     Applications in the backup archive ............. : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][opsxml][cwportal][ipm][upm][cvw]
     WARNING: The list of applications installed on this CiscoWorks server does not match the list of
              applications in the backup archive. If you restore data from this backup archive,it may
              cause problems in the CiscoWorks applications.
              Do you want to continue the restore operation? (y-continue or n-quit, y/n)?Y
     Applications to be restored are................. : [Common Services] [Campus Manager] [Resource Manager Essentials] [Device Fault Manager] [cwportal] [ipm] [upm] [cvw]
     Available disk space in NMSROOT................. : 86451488 Kb
     Required disk space in NMSROOT.................. : 35906524 Kb
     (The temp and NMSROOT are on same device, therefore this required disk space includes temp space)
Copying the backup files to the temporary location [/opt/CSCOpx/tempBackupData]
preRestore of [Common Services] has started.
preRestore of [Common Services] has completed.
preRestore of [Campus Manager] has started.
preRestore of [Campus Manager] has completed.
preRestore of [Resource Manager Essentials] has started.
preRestore of [Resource Manager Essentials] has completed.
preRestore of [Device Fault Manager] has started.
preRestore of [Device Fault Manager] has completed.
preRestore of [cwportal] has started.
preRestore of [cwportal] has completed.
preRestore of [ipm] has started.
preRestore of [ipm] has completed.
preRestore of [upm] has started.
preRestore of [upm] has completed.
preRestore of [cvw] has started.
preRestore of [cvw] has completed.
doRestore of [Common Services] has started.
          Cross Platform Update started.
          Cross Platform Update completed.
          License check started.
             WARNING: The license details in the server are different from the backup data.
                      After restoring, please check the license available in the server.
             WARNING: Your current license count is lower than your earlier license count.
                      If you restore the data now, devices that exceed the current licence count
                      will be moved to Suspended state.
          License check completed.
          Restoring certificate.
             WARNING: Cannot evaluate the hostname, hence the certificate
                      may be from this host or another host.
                      [ Certificate not overwritten ]
          Restored Certificate.
          Restoring Common Services database.
          Restored Common Services database.
          Restoring CMIC data.
          Restored CMIC data.
          Restoring CMC data.
          Restored CMC data.
          Restoring Security Settings.
          Restored Security Settings.
          Restoring DCR data.
          Restored DCR data.
          Restoring Certificate key store.
          Restored Certificate key store.
Restoring DCNM CrossLaunch data.
          Restored DCNM CrossLaunch function.
          Restoring JAAS configuration.
          Restored JAAS configuration.
          JRM Job Migration started.
          JRM job Migration done.
doRestore of [Common Services] has completed.
doRestore of [Campus Manager] has started.
          Cross Platform Migration for Campus started.
Cross Platform update Starts for Campus
doRestore of [Campus Manager] has completed.
doRestore of [Resource Manager Essentials] has started.
10% of RME Restore completed
30% of RME Restore completed
50% of RME Restore completed
70% of RME Restore completed
100% of RME Restore completed
doRestore of [Resource Manager Essentials] has completed.
doRestore of [Device Fault Manager] has started.
10% of DFM Restore completed
30% of DFM Restore completed
50% of DFM Restore completed
80% of DFM Restore completed
Going to modify Eight PM report
Modified Sucessfully Eight PM report
100% of DFM Restore completed
doRestore of [Device Fault Manager] has completed.
doRestore of [cwportal] has started.
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.script ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.log ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultUserCommunity.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultCommunity.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
doRestore of [cwportal] has completed.
doRestore of [ipm] has started.
        10% of IPM Restore Completed
        30% of IPM Restore Completed
        50% of IPM Restore Completed
        60% of IPM Restore Completed
        70% of IPM Restore Completed
        100% of IPM Restore Completed
doRestore of [ipm] has completed.
doRestore of [upm] has started.
HUM database restore starts
INFO:STOP= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
SQL Anywhere Command File Hiding Utility Version 10.0.1.4239
INFO: Database Shutdown is in Progress..Please wait
INFO: Stop Engine Args= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
INFO: After Database Shutdown RC= 2304
root=C:\PROGRA~2\CSCOpx\databases\upm\upm.db
DBUTILS: Inside Cross Platform
INFO: Current Database password does not match the password of Database being restored
INFO: Using the Password of the Database being restored
HUM database restore successfully completed.
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate/README.txt
Directory is reportsStarted changing property .
linux
Restored HUM configuration file successfully.
doRestore of [upm] has completed.
doRestore of [cvw] has started.
doRestore of [cvw] has completed.
postRestore of [Common Services] has started.
postRestore of [Common Services] has completed.
postRestore of [Campus Manager] has started.
postRestore of [Campus Manager] has completed.
postRestore of [Resource Manager Essentials] has started.
postRestore of [Resource Manager Essentials] has completed.
postRestore of [Device Fault Manager] has started.
postRestore of [Device Fault Manager] has completed.
postRestore of [cwportal] has started.
postRestore of [cwportal] has completed.
postRestore of [ipm] has started.
postRestore of [ipm] has completed.
postRestore of [upm] has started.
postRestore of [upm] has completed.
postRestore of [cvw] has started.
postRestore of [cvw] has completed.
Restored successfully.
Are this errors going to affect our LMS 4.2 operations?
Then we have upgraded to LMS 4.2.2 and exported data and credentiales for PI import.
On PI 1.3 we have installed WCS 500 devices upgrade license and LMS 1500 upgrade license and now we are having 2000 devices lifecycle license. We have successfully restored WCS data in PI and we have imported LMS devices as bulk import. What is strange is that we have this message in prime regarding licensing:
On LMS 3.2 our customer had saved unlimited number of configuration versioning. After upgrading to LMS 4.2 we can only see last 3 configurations regardless of unlimided number of configurations in previous LMS, so my question is where can we find older configurations in LMS 4.2?
We are planning to turn unlimited versioning on CPI 1.3 now, so our customer will again have feature that they need. Do you have some experiance regarding disk space when all device configurations are stored forever?
Thank you for your help.
Regards,
Jelena

Cisco Prime 1.2 - same WLANID accross all controllers

Similar Messages

Maybe you are looking for