Cisco Prime 2.1 Archive Search

in past versions of CiscoWorks I was able to search configuration archives.  
Config MgmtArchive MgmtSearch Archive
Can I do that with Cisco Prime 2.1???

You can thin provision. Trying to change the overall profile though will most likely result in issues sooner or later. When you run out of disk space it will fail in ungraceful ways.

Similar Messages

  • Cisco Prime 2.2 Config Archive get Partial-Success

    Good morning everyone!
    I have a question regarding Cisco Prime Infrastructure 2.2 and Config Archive. Im trying to backup a configuration for an old WS-CBS3020-HPQ blade with IOS version 12.2(58)SE1 and im getting an error under "Fetch vlan" that says :
    Couldn't able to collect VLAN on the device. TFTP server not accessible from device.
    Im not sure what this means? It gets partial-success, but the error message worries me. Im not able to find anything in the logs or by searching for the error code. Anyone have any idea where to look? The credential is correct, i tripple checked :)

    I tried using the "tftp-server flash:" command, but didnt help. Im also seeing this problem with a couple of Cisco 3750x switches.

  • Cisco Prime Configuration Archive on Interface Flap

    Hey All,
    We've been using Cisco Prime 2.1 for a bit now and I have a question about the configuration archive based on change events.  Will Cisco Prime go and attempt to perform a config backup based on an interface flap?  Looking at the audit logs it appears that it does that (see attachment).  Is this a default behavior and does anyone see any benefit to this?  It seems like if an interface is flapping it will continuously log into the device to see if the configuration has changed.
    Brian

    Hi Brian,
    I don't think configuration achieve can be triggered due to interface flap ,however if there is any change in the configuration yes PI can do the config Archive
    Go to Administration > System Settings > Configuration Archive
    Archive Configuration on receiving configuration change events?    Check box this option
    Thanks-
    Afroz
    ***Ratings Encourages Contributors *****

  • Cisco Prime Infrastructure release 2.1 configuration archiving on CISCO WiSM2

    Hi all,
    Just wondering Cisco Prime Infrastructure  release 2-1 support configuration archiving on CISCO WiSM2?
    CISCO  release 2.0 mentioned that it doesn't support configuration archiving for WiSM2 but release 2.1 doesn't mention anything on it.
    Please assist.

    No, it is not supported even for PI 2.1

  • Cisco Prime Infrastructure Scheduled Configuration Archive not executing

    We have a deployment of Cisco Prime Infrastrcuture 1.3 (1.3.0.20).
    Configuration Archive is a feature that collects and archives the device configurations i.e. cisco switches.
    You have an option to schedule this to run, say daily, weekly etc. Once scheduled you can see it in the "Jobs Dashboard" and with the "next start time" of what you configured. I have a situation whereby  the time it is suppose to start - it doesnt - howevere flags the job as a "success". Not newe device configurations are archived and the "next start time" remain the same. Its almost like it is failing to execute, but some other process under the hood thinks that it was been executed correctly?
    Any ideas or experience that could help here would be appreciated!

    Some extra info that has just come to my attention.  At one point we were running (we're actually still running) CiscoWorks with LMS3.2 and Cisco NCS 1.x.  I merged these two things together into Cisco Prime Infrastructure (upgraded the licensing to get 450 lifecycle licenses to cover the APs + all of the devices coming from LMS3.2).  I followed all of the documented procedures to upgrade the NCS appliance to Prime Infrastructure.  But when I type "show application" from the CLI of the NCS appliance (now the Prime Infrastructure appliance) I see this:
    HQ-NCS1/admin# show application
    NCS             Cisco Prime Network Control System
    Is that normal?  Maybe this is my problem.  Should this output list "Cisco Prime Infrastructure" instead of (or in addtion to) Cisco Prime Network Control System?  When I login to the GUI it shows "Cisco Prime Infrastructure" and the GUI has changed considerably (menus are different) so I'm assuming that the application upgrades I launched from the CLI to go to Prime Infrastructure worked fine.

  • Cisco Prime Infrastructure Archive location

    Hi All,
    Kindly I need to know what is the location of Archieved Configuration Backup that taken by PI (are they saved in a specific repo or what?) and how can I gather them automatically??
    thanks
    Best Regards.

    ok thanks alot.
    kindly I want to ask for another issue.
    after I configured the global mail setting on my cisco prime infrastructure (I set the ip of primery SMTP then sender and reciever parameters) then I press on test button to send a test mail but it not send ??
    note that:
    I made sure all services are running using (ncs status) command
    I appreciate your kindly help

  • Cisco Prime LMS 4.1 course needed

    Hi folks,
    In near future we're going to migrate our LMS 3.2 to new LMS 4.1.
    Have anybody know if any Cisco courses for Cisco Prime LMS 4.1 are available to buy, order or download? If so, wher I can find it.
    Thanks in advance for help

    If your employer is willing to let you travel to instructor-led classes, you could search for providers of the 5-day "Implementing CiscoWorks LMS 4.0". Here's a course outline of this class, from the intraweb:
    1. Introduction to CiscoWorks LMS 4.0
    Defining Network Management
    Exploring the Network Management Process
    Basics of CiscoWorks LMS 4.0
    2. Getting Started
    Installing CiscoWorks LMS 4.0
    Logging into CiscoWorks LMS 4.0
    Using the Getting Started Workflow
    3. My Menu
    Basics of My Menu
    Managing Dashboards, Portlets, and Portal Layout
    4. Inventory Management
    Collecting Inventory and End User Information
    Performing Device Administration
    Viewing and Creating Inventory, User Tracking, and Switch Port Reports
    Using Inventory Tools
    5. Configuration and Software Management
    Managing the Configuration Archive
    Verifying Configuration Compliance
    Using Configuration Tools
    Using Configuration Workflows
    6. Network Monitoring and Troubleshooting
    Visualizing the Network with Topology Services
    Monitoring Network Performance
    Monitoring Network Response Time
    Monitoring Syslog Messages
    Monitoring Network Faults
    Using Troubleshooting Tools
    7. CiscoWorks LMS Work Center
    Using Smart Install Work Center
    Using Identity Work Center
    Using Auto Smartports Work Center
    Using EnergyWise Work Center
    8. CiscoWorks LMS Administration
    Using the Trust Management Menu
    Managing Collection Settings
    Performing Network Administration Tasks
    Performing System Administration Tasks

  • What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP's?

    What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP’s?

    • PI provides visibility for autonomous  clients within the same list view as lightweight and wired clients (client list  page).
    • Rogue AP detection for autonomous AP's is not supported (it's  supported in CUWN). 
    • Alarms/events for client authentication issues (e.g.  authentication failure) are displayed in PI.
    • Config management for  autonomous AP's is via CLI template.  Config comparison and archiving  functionality in PI leverages these same features that were brought in from LMS,  so need to defer to others in terms of whether this is a cross-platform feature  in PI or is only supported on a subset of platforms.  Config comparison/archive  is supported in CUWN.PI supports both infrastructure (e.g. AP Tx Power and  Channel, busiest AP, AP utilization, etc.) and client (e.g. client count, client  sessions, etc.) reports, and there are extensive reports for CUWN

  • Cisco Prime Collaboration Deployment with BE7K and VMWare license

    Hello, I am looking for some help trying to figure out if Cisco Prime Collaboration Deployment can be used to upgrade our existing 7.1.5 cluster.  From what I have read there is a API problem with the VMWare license that comes with the BE7K.  But after reviewing the BOM/quote from my VAR it lists the foundation license which based of the release notes is supported.
    UCSS-U-VMW-FND-5-1
    UCSS Cisco UC Virt. Foundation  Five Year - 1 server
    Has anybody out there had expericne with PCD and BE7K'?
    This is from release notes of PCD
    http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/rel_notes/10_5_1/CUCM_BK_P139675A_00_pcd-rns-1051/CUCM_BK_P139675A_00_pcd-rns-1051_chapter_010.html
    Search for “Business Edition 7000” and it will state it is not supported with PCD.  It is because the licenses that the BE 6k and 7K are shipped with don’t enable certain VMware APIs that PCD needs.
    “Virtualization Software License Compatibility
    Cisco Prime Collaboration Deployment is not compatible with all license types of VMware vSphere ESXi, as some licenses do not enable required VMware APIs.
    The following are compatible with Cisco Prime Collaboration Deployment:
    Cisco UC Virtualization Foundation (appears as "Foundation Edition" in vSphere Client)
    VMware vSphere Standard Edition, Enterprise Edition, or Enterprise Plus Edition
    Evaluation mode license
    The following are not compatible with Cisco Prime Collaboration Deployment:
    Cisco UC Virtualization Hypervisor (appears as "Hypervisor Edition" in vSphere Client)-preloaded on Cisco Business Edition 6000 and Business Edition 7000
    VMware vSphere Hypervisor Edition
    Any help would be appreacted.
    JP

    Thanks Jamie for repsonding, we haven't made any purchase's yet but I wanted to ensure we are purchasing a solution that won't lead to a lot of frustration.  We only have 1000 phones so we are pretty small and the BE7K seems to be a good fit and value.
    Cheers,

  • Cisco Prime Infrastructure 2.0 and Cisco ASA

    Hello,
    We've recently installed trial version of Cisco Prime Infrastructure 2.0 Express. We hoped that it already supports Cisco ASA 55xx series (especially 5505, we have pretty amount of them). But we had some problems with PI and asa durind the exploitation process.
    First, I've added ASA to PI, and Inventory Collection Status is Completed, but I can't see CPU and RAM utilization graphs. Inventory.logs are non-informative.
    Also, config backup is success, but when I try to watch the backuped configuration at Configuration Archive PI says "Failed to fetch raw configuration". And so on.
    ASA version is 5505, image is 9.1(2).
    So, I have a question: is it possible to manage ASAs with PI 2.0?
    UPD: I've just tried to upgrade asa to 9.1(4), and behavior of the equipment is quite the same. Seems we shall wait for 9.2 to be released.

    Have you downloaded and applied the latest Device Pack updates?
    PI enhanced ASA support after the initial 2.0 release and the Device Packs incorporate that change.
    The README file for Device Packs explains how to install them. (A bug currently does not allow the direct download in PI so you need to follow the method for installation from local storage after you manually download. Here is a link to the download location.

  • Cisco Prime Infrastructure 1.2 synchronizaton with active directory

    hi all
    I have installed Cisco Prime Infrastructure 1.2 and I want to make a synchronization between the PI and the active directory
    note:
    I want to make that to be able to search about the users on cisco prime infrastructure using Hostname instead of serching on it using IP or MAC address.
    how can I do this task ???
    thanks all.
    I appreciate your support.

    Hi Mohamed,
    Integration with AD is not supported in PI
    Thanks-
    Afroz
    [Do rate the useful post]

  • Cisco Prime 1.2.1.12

    Hi All,
    Running PI 1.2.1.12, need to recover the admin password for the command line interface any ideas.
    Cheers,
    Jay

    Followed the above can only find .OVA file shown? (PNP-KICKSTART-VM-1.2.11-medium.ova)
    Will this file work?
    If you do not have a copy of the ISO image, you can download it from Cisco.com, as follows:
    a. Point your browser to http://software.cisco.com/download/navigator.html.
    b. Use the Find box to search for "Cisco Prime Infrastructure". From the results list, select the software version you are using (for example, Cisco PrimeInfrastructure 1.3).
    c.Select
    Prime Infrastructure Software to display the list of ISOs and other downloadableimage files for that software version.d.Download the ISO image from the page.
    e.Once you have a copy of the ISO image, upload it to a datastore on your virtual machine, as follows.
    If you do not have access to the vSphere inventory, Datastores or Objects functions, consult your

  • Cisco Prime Demo

    Hi all,
    I download Cisco Prime Express 2.1 from www.cisco/go/prime-demo the trail version . the file saved as zip file. when i try to open  or extract , it didn't open and show this massage :
    Cannot open file ; it does not appear to be a valid archive.....
    I download it couple of times from my laptop and my team but same massage appear . can some one help please. 

    Wrong section to post this question. Check if you are going via proxy or firewall for download. Check your extracting tool works correctly.

  • Can Cisco Prime Infra 2.1 work as syslog server

    Hello all,
        Customer want Cisco Prime Infra 2.1 to work as syslog server.  they want to query text in syslog and get raw log file from Cisco Prime Infra.  but when i see in user interface.  I think that it cannot query and search text in syslog.  but i am not sure whether we can get raw log file per devices from Cisco Prime Infra.   Can anyone know about this.?
    thanks
    sompoj

    Hi Sompoj,
    In the prime infrastructure Syslogs are directly read from udp port 514 and then filtered
    , the non SEV1 and SEV2 syslogs will be dropped and will not be entered into db . The
    syslog messages will not be saved into log files .
    Thanks-
    Afroz
    ****Ratings Encourages Contributors ****

  • Cisco Prime Infrastructure 1.x Server requirements & Operating System

    Dear Friends
    I wish you are in very good health ........ I really very confused regarding LMS and i really needs your help ........ I need to order LMS for one of our customer with 500 devices and reporting cabailities ..... So i chosse base license "R-PI-1.1-K9" and 500 device license "R-PI-1.1-500-K9" and
    Compliance Management - 500 Device License "L-PI-1.1-CM-500"
    What really confused me that i tried to search server cabalitity for my requirments & Operating system and couldn't find it ...... what i need your help for is the following:
    1) What is the server requirments ???
    2) What is operating system (windows 2008 or VMWare VMware ESX/ESXi Version 4.1 or 5.0)
    3) Is their any deticated applicance from Cisco ??
    Please help
    Thanks in advance

    In addition to the release notes for the 4.2.3 patch noted above, please also see  the 4.2 release notes which further direct you:
    Server and Client Requirements
    For information on server and client requirements for the system and browser, see Chapter 2 of Installing and Migrating to Cisco Prime LAN Management Solution 4.2 at:
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/install/guide/
    install.html
    To summarize the options it describes, you can run the LMS product on any number of platforms - a dedicated Cisco hardware appliance, a physical server of your own with Windows or Solaris OS, a VMware server with a Windows server OS guest, or a "soft appliance". The soft appliance is package built with the underlying guest OS (a customized RHEL distribution with Cisco's Application Development Environment OS (ADE-OS)) built-in.
    Once you have installed LMS 4.2, you should patch - first to 4.2.2 and then to the current 4,2,3. then run the software update feature to bring all package components up to date.
    Regarding licensing, there is a Cisco Prime Infrastructure Ordering and Licensing Guide here.
    When you order the licenses for PI 1.2 (new customer), you order the base product and then Lifecycle licenses (required for either PI 1.2 Lifecycle and LMS installations - which option is a customer choice) and, optionally, Compliance and Assurance licenses. An upgrade order for an existing LMS customer will include the base PI 1.2 with Lifecycle licenses as well as LMS in a single SKU as noted in tables 4 and 5 of the Ordering Guide.

Maybe you are looking for

  • Exception Handling for many bean objects of a container class in a JSP page

    Hello, I have on container bean class. In this container class, there are several others class objects and the getter methods to get these objects out to the JSP pages. I have one JSP page which will use different objects in the container class objec

  • Free Trial of Adobe Photoshop CS6 Troubleshooting

    I downloaded the extended free trial version of the program and used it to create a poster. I started to create a cd cover for my clients single release. I was unable to finish the product for lack of time, and so, closed the program. I came back to

  • XMLType performace

    Hello I have 2 tables. One has an xmltype column. The way I have to joing these 2 tables is by writing the query like: select ... from table1 t1 where t1.col1not in ( select distinct lki from table2 t2 where to_char(lki) in (select distinct ft3.xmlco

  • Need Help With Installing Again

    Okay this is what I get when I try to install Java ****Start Quote**** The feature you are trying to use is on a network resource that is unavailable. Click OK to try again,or try an alternate to a folder containing the installation package 'jre.msi'

  • Exporting selections from a sequence onto DVD

    Hi all I have edited twenty-four public service announcements on a single timeline. What is the best way to export them, three at a time, onto eight separate DVD's, with the least drop in quality?