Cisco Prime 2.1, Removing Subgroup from Group in the Device Work Centre

Hi All,
I am having trouble removing a Device Group from within a Group in Cisco Prime.
In short, there is a group called 'Cisco 3850 Series Ethernet Stackable Switch' which exists under both the 'Wireless Controller' group and the 'Switches and Hubs' group. I want to remove it from the 'Wireless Controllers' group as we are not using the controller functionality of the deivce.
Can anyone help on this issue?
Thanks,
Cameron

Hi TD,
I would suggest you to take both the backup ::
Application and appliance backups
Prime Infrastructure creates two types of backups:
Application backups: These contain all Prime Infrastructure application data, but do not include host-specific settings, such as the server hostname and IP address.
Appliance backups: These contain all application data and host-specific settings, including the hostname, IP address, subnet mask, and default gateway.
Note that:
Application and appliance backups can be taken from both virtual and hardware appliances.
Either type of backup can be restored to the same or a new host, as long as the new host has the same hardware and software configuration as the host from which the backup was taken.
You can only restore an application or appliance backup to a host running the same version of the Prime Infrastructure server software as the server from which the backup was taken.
You cannot restore an application backup using the appliance restore command, nor can you restore an appliance backup using the application backup command.
refer the below links::
http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-2/administrator/guide/PIAdminBook/backup_restore.html#10347
http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-2/administrator/guide/PIAdminBook/backup_restore.html#72460
Thanks-
Afroz
***Ratings Encourages Contributors ****

Similar Messages

Deleted WLC from its folder under the Device work center of Cisco prime 1.2

I kindly need your help as regarding cisco prime infrastructure.
I added the wireless LAN controller to the prime. I later had to troubleshoot the WLC because the reachability status showed UNREACHABLE.
Due to my troubleshooting, I synched the WLC a couples of times and the collection status has been showing SYNCHING since then.
I also tried deleting the WLC from its folder under device work center and it deleted but it still reflects under the ALL folder.
Please would I have to wait for the SYNCHRONIZATION of the WLC to stop before I can completely delete it and re-add??
Also I noticed that after deploying ''Interface Health'' under Monitoring Configurations, the CPU and memory utilization did not reflect for the devices cisco
prime is managing.
What have I missed out?
Kindly help.

Prime Infrastructure won't support those legacy models.

CSSImport Utility - Remove Users from Groups

We have a security group that has a few hundred users assigned to the group. When there is a need to remove a user from the group it is difficult to find the user as I have comb through the list to find the user i am trying to remove. Two questions: is there a way to sort the users in the group in Share Services? The second question is can users be removed using the CSSImport utility by specifying the "delete" option in the importexport.properties? Does the "delete" option remove the user from the secuity group and or does it delete it completely from ShareServices? (we are using Hyperion v9.3.0.1.0 Build 5)

Hi,
I am not so sure about the sorting but removing users from groups can be done with the CSSImportExport utility, I see you are on 9.3.0, try and get hold of the 9.3.1 version as it is backward compatible to the 9.3.0 version and more stable.
When removing users from groups, just set your import operation to update
import.operation=update
and in your import csv just put the group children elements and the users you want in the group.
#group_children
id,group_id,group_provider,user_id,user_provider
TestGroup,,,UserToKeepInGroup,Native Directory
This way it will keep the users in the import file and remove the users from the group that are not in the file, also it does not remove the user from shared services only from the group.
Ok?
Cheers
John
http://john-goodwin.blogspot.com/

Add/Remove members from groups

Does anyone have a sample ldif entry to add/remove members from groups?

I am not exactly getting what you said here.
Basically if your intention is to rename RDN and reflect the changes in the group membership, you have to do totally 2 operations:
1) update your uid on the user entries.
2) update your membership on the group entry: remove the uid first, then add it:
updateM.ldif
dn: cn=groupA,ou=groups,ou=xxxxxxxxxxxxxxxxxxxxx
changetype: modify
delete: uniqueMember
uniqueMember: uid=1111,ou=people,ou=xxxxxxxx
add: uniqueMember
uniquMember: uid=zz1111,ou=people,ou=xxxxxxx
save it
run:
ldapmodify -v -D xxx -w xxx -h xxx -p xxx -f <PATH>/updateM.ldif

Remove buddy from group

Hi,
I've got iChat 3.1.9 and have an issue where my buddies are showing up in multiple groups. So they are showing up in my Family group as well as my Buddies group and I can't figure out how to remove them from one of the groups without removing them from iChat entirely. Is there an easy way to fix this? Maybe a setting in Address Book or something I'm missing? Thanks so much.
-NifflerX

Hi,
Drag them from the group they appear in to the Group you want them to be in (even if already there)
You probably used a Modifier key (Shift or the Apple Key) to Move + duplicate the Buddy in different groups before.
7:49 PM Sunday; October 11, 2009
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"

Why can't I remove attachments from emails in the Sent items folder?

I Recently upgraded from Snow Leopard to Lion, and so far, there are at least a couple of things that puzzle me.
One is that now I don't have the option to "Remove Attachments" from emails in the sent items folder. It seems to work normally
in the Inbox and Drafts folders, but not in the Sent items. Go figure ???
Another thing that bothers me is that in Preview, when I save a screen shot, or a scan, etc., I no longer have the option of saving it as a GIF
(which, when better quality isn't absolutely necessary, is often much lower in KB or MB than a PNG or JPG, etc.. When I store lots of things as such images, I'd rather have that option.
Any suggestions will be appreciated.

I have now created a smart mailbox as described above (good idea), and although I have some 50 messages in my Sent box, all with attachments (waiting to be removed so I can store the messages in the proper mailboxes), the smart mailbox is empty. So, Mail doesn't recognise these messages as containing attachments.
This led me to think that maybe Mail has been redesigned to work the way you would expect it to, at last; to contain a link to attachments instead of including them in all their bits and bytes. That would mean that the messages in my Sent box - with attachments - could be stored in local (or server-side) mailboxes without taking up extensive space.
But then I checked the size of my Sent Messages folder inside the Mail Folder in Finder, and - whoops - it's 50+ MB. So the sent messages do contain attachments all right. And Mail doesn't recognise these, since a) the smart mailbox trick says that the messages are free from attachments, and b) the Remove Attachments menu option is disabled.
I will have to wait for the next Mail update, and my Sent box will grow accordingly ...

[svn:fx-trunk] 5140: Removing [ExcludeClass] from classes outside the package.

Revision: 5140
Author: [email protected]
Date: 2009-03-02 12:09:24 -0800 (Mon, 02 Mar 2009)
Log Message:
Removing [ExcludeClass] from classes outside the package.
QE Notes: None.
Doc Notes: None.
tests: checkintests
Modified Paths:
flex/sdk/trunk/frameworks/projects/flex4/src/mx/layout/HorizontalLayout.as
flex/sdk/trunk/frameworks/projects/flex4/src/mx/layout/VerticalLayout.as

HT4946 How do I backup ALL of my iPad content onto a newly purchased MacBook Air? I can't backup up apps or music from CDs through the device backup function.

How do I backup ALL of my iPad content onto a newly purchased MacBook Air? I can't backup up apps or music from CDs through the device backup function.

First you need to authorize your MBA with your iTunes account with iTunes if you haven't already done so.
With your iPad connected and without syncing, at the iTunes menu bar go to File and select Transfer Purchases From - the name of your iPad. This will transfer/copy all iTunes content on your iPad that was purchased/downloaded from the iTunes store only.
Photos on your iPad that were transferred from your old computer need to be transferred from your old computer to your MBA.
Before syncing contacts with the Address Book and calendar events with iCal if you aren't syncing this content over the air with an iCloud account, enter one contact in the Address Book and one calendar event in iCal on your MBA. Make these up if needed, which can be deleted later. This will provided a merge prompt with the first sync for this data, which you want to select.
Photos/videos in the Camera Roll can be imported by your MBA with iPhoto or the Image Capture application.

I have purchased my i phone 5 one month back, unfortunately I have got some hardware problem like some part has been broken from inside, but the phone works without any issue, Did anybody face this issue?

I have purchased my i phone 5 one month back, unfortunately I have got some hardware problem like some part has been broken from inside, but the phone works without any issue, Did anybody face this issue?

If you believe there is a hardware problem, call AppleCare or make an appointment at an Apple Store if there is one nearby.

Two questions.1)If I plan to buy an unlocked iPhone 5 from Canada will the 4G work in Egypt although mobile operators haven't launched it yet? 2)Once the iPhone 5 is launched here,will the unlocked iPhone that i purchased from Canada work?

Two questions.1)If I plan to buy an unlocked iPhone 5 from Canada will the 4G work in Egypt although mobile operators haven't launched it yet? 2)Once the iPhone 5 is launched here,will the unlocked iPhone that i purchased from Canada work?

Sarah.Efat wrote:
Two questions.1)If I plan to buy an unlocked iPhone 5 from Canada will the 4G work in Egypt although mobile operators haven't launched it yet?
More than likely, no.
2)Once the iPhone 5 is launched here,will the unlocked iPhone that i purchased from Canada work?
Yes.

Removed user from group, user no longer has access to documents even though user is owner of documents

I'm running a server 2012 std domain and I'm in the process of rebuilding our fileserver after we had some pretty serious permission issues. Bad permissions (Everyone had full access to user documents share) were migrated when we move to the new server and
then by some strange Monday morning freak out all users lost access to their documents. I restored from backups, redirected everyone's folders back to local computer and started to reconfigure the share permissions. I moved our administration group back to
the server after securing proper permissions for folder redirection (permissions copied from https://technet.microsoft.com/en-us/library/jj649078.aspx?f=255&MSPPError=-2147217396 table 1, only difference is instead of creating a new security group
for redirection users, I used the everyone group) to test and everything went perfectly. The GPO created the users folders under the root and redirection was good to go. Along with that, other users cannot access other users documents anymore which was the
intended outcome.
Last night I was looking at security groups and see that our administration group (back office group: accounting, HR, etc..) was a member of the domain admins. I removed them from the domain admins group and added them to the administrators group (they do
need regular admin access) then went on like normal. This morning, all users in that group can no longer access their documents on the server. I immediately think that permissions were broken again and started to get angry, but then realize that all the files
are still accessible on the server (no lost permissions like before) and the user is still shown as the owner with full permissions, but the files are inaccessible to those users. I re-added them to the domain admins group, logged out, logged back in and documents
are back and accessible by the user. Remove them from the domain admins group, log out, log back in and the documents are inaccessible again. Re-add to the domain admins group and back to normal.
Which leads me to now. If the users are part of the domain admins group, they have access to their files. If they are removed from the domain admins group, they lose access. When they lose access, they are still the owners of the files/folders with full
permissions, yet they can't access their documents. Also, just to add, the domain admins group has no specified permissions on the files or folders. See screenshots below..
Here is the root share.
And the user's desktop folder. The folder is owned by the user with full permissions. This is the folder the redirection GPO created.
Any ideas why removing the group from domain admins would drop access to their files? They are still the owners of the files and should have full access but they don't. Is there something I'm not seeing here?

Effective Access shows the user has full control of the Desktop folder
This is a problem with the Effective Access tab when using CREATOR OWNER. As you have noticed, the user doesn't really have the access that the tab says it does. This is because of how CREATOR OWNER works.
CREATOR OWNER is only evaluated when a file/folder is created.
IF a user can create a file/folder, then the permissions assigned to CREATOR OWNER are copied to a new permissions entry for that user.
To see this:
Logon as an administrator and create a file in the Desktop folder in your screenshot.
Examine the permissions of the new file.
You'll see that there is a new entry for the account you logged on with.
CREATOR OWNER is gone. CREATOR OWNER would still be there if you created a folder (because of "subfolders and files").
In the Desktop folder (in your screenshot), only SYSTEM and Administrator can create/access files.
To fix this, you need to grant the users the ability to list the directory contents and create new files/folders. This corresponds with the suggestion of Table 1 in the document you found.
I see what you're saying about Administrators domain group. I'll just add them as local admins via GPO and that should solve that issue.
No, scary! This will grant those users administrative permission on your server. They will be able to see any file anywhere on that server.
If your goal is to provide a place that is private for each user, then the simplest approach is to grant each user permission to their own folder. Like this for Test User:
Notes for above:
I set the user's permission to Modify because there is no good reason why the user should change these permissions
The owner of this folder is unimportant. I leave it set to Administrators
You can, and I do, remove CREATOR OWNER. It adds no value in this situation and just causes confusion.
As for the second screen shot, the *-Admins folder is the root to which Everyone has special permissions on and can create folders. The folder for M* was created by the GPO, which makes M* the owner to which they have Full control of subfolders and files.
The GPO also created the Desktop folder, giving owner full permissions of subfolders and files. Inside the Desktop folder, permissions remain Full control for owner for subfolders and files. Even if it was the case that they only had permissions on subfolders
and files, wouldn't each subfolder under that one be considered a subfolder and file of the top folder?
If this works as you say, then Yes, it should work. But, I don't see the entries for use M*. Remember, there should be entries for the M* user that is a duplicate of CREATOR OWNER.
I suspect that Group Policy is creating the directories (elevated) and then changing the owner to M* afterward. This does not duplicate the CREATOR OWNER entries as needed. If this is the case, I consider it a flaw because your permissions do
not allow user M* to create files/folders, and group policy shouldn't bypass security.
I'm not saying your wrong, I'm just curious why the technet article would advise Creator/Owner giving full control of subfolders and files only if that were not correct. I can add the permissions for the users easily, I just don't see why I need to give
explicit permissions to access something when the GPO created those folders for me, which Microsoft recommends you allow. If the GPO can create folders and the folders are owned by the user, then the user can obviously add/create/modify/view those files and
folders.
When I restored the data, no permission were reset. Permissions were restored to the wonky version where the Everyone group has full access to everything. Ownership of the files/folders remained the same.
A couple things:
The article instructed the use of Folder Redirection Users group that had permissions to create files. Your examples didn't have that. Because of this, your user could create new files.
The article assumes that the directories you are creating will be empty. Existing files will be unreadable to everyone except Admins.
If you follow the directions in the article, then anyone in the Folder Redirection Users group can write files to anyone else's directory.
One benefit of the document's approach is that all the users could be redirected to the same folder using the article, and it would work. A benefit, I guess.
But, I like my user's separate and unable to see each other's files -- at all. This is why I recommend replacing CREATOR OWNER with the specific user.
I believe this document is a "how to get it done" document, not necessarily a best practices document. I see it as a starting point, and that's why I didn't follow it exactly.
Lastly, CREATOR OWNER permissions are useful but confusing. I avoid them unless I have the rare circumstance where they are perfect.
When I restored the data, no permission were reset. Permissions were restored to the wonky version where the Everyone group has full access to everything. Ownership of the files/folders remained the same.
To summarize:
In the user's directory, you need to provide permission to list and create new files/folders, and you need grant the user permission to the existing files.
-Tony

Remove tasks from group to-do list

Hi all,
I have been testing my workflow and have terminated all of my test processes. Now some of the tasks are still present in the Group list I can not grab them and add them to my own to-do list anymore.
How can I remove them from the Group to-do list?
Sincerely
Kim Christensen

You can terminate them from the adminui under Services/Process Management/Process Management.
Jasmin

Remove user from group with MaxL

hello,is it possible to remove a user from all groups he belongs to without knowing these groups?I want to execute a command such as "alter user my_user remove from ALL_GROUPS;"thanks for your help/

Not sure if it's feesible, but you could use the 'drop user' command to remove the user from the system, which would of course remove them from all groups, then use the 'create user' command to recreate the user and reassign them to the proper groups.Good luck

To remove user from Group

I created a new user account from SSH connection to our cluster. The user belongs to two groups by default: nobody and wheel. I tried to delete him from the two group by using dscl command, I got the following error:
/NetInfo/root/Groups > delete wheel GroupMembership ryan
<main> attribute status: eDSAttributeNotFound
/NetInfo/root/Groups > read wheel
AppleMetaNodeLocation: /NetInfo/root
GeneratedUID: ABCDEFAB-CDEF-......
GroupMembership: root
Password: *
PrimaryGroupID: 0
RealName: System Group
RecordName: wheel
RecordType: dsRecTypeStandard:Groups
SMBSID: ......
I would like to know how to remove him from the two groups. Thank you very much.
Apple Cluster Mac OS X (10.4.3)

I had to update the code to the following because Get-SPUser was not working properly:
$url = "https://sharepointdev.spfarm.spcorp.com/sites/desitecoll"
$userName = "spfarm\spprofileimport";
$site = New-Object Microsoft.SharePoint.SPSite($url)
$web = $site.OpenWeb()
$siteGroups = $web.Groups;
Clear-Host
$mySiteGroups = @();
foreach($group in $siteGroups)
Write-Host $group
$mySiteGroups += $group;
}#foreach
$members = $web.Groups[$mySiteGroups[0]];
$owners = $web.Groups[$mySiteGroups[1]];
$visitors = $web.Groups[$mySiteGroups[2]];
#Convert the user name to an SPUser account
$spUser = $web.Site.RootWeb.EnsureUser($userName);
Write-Host $spUser.ID
Remove-SPUser -Identity $spUser -Web $url -Group $owners
$web.Update();
$web.Dispose();
Write-Host "User " $userName "removed from " $owners
Was I not using Get-SPUser correctly?

Cannot remove songs from playlists in the latest iTunes version

I am running iTunes 11.1.5. When I select a song or songs in a playlist that I want to remove from the playlist (but keep in iTunes) and hit the Delete or Backspace key nothing happens. What's strange is I am able to remove songs from some of my playlists but not others. Does this behavior work differently in playlists I create myaself and playlists iTunes provides for you? It seems I can remove songs from my own playlists but not from the ones provided by iTunes.
Thanks.
Jesse

You cannot manually add or delete from smart playlists (they appear in purple in my iTunes and at the top of all the playlists). Smart playlist content is generated by the rules controlling the playlist. Right (control+) click on a smart playlist to see the rules.

Cisco Prime 2.1, Removing Subgroup from Group in the Device Work Centre

Similar Messages

Maybe you are looking for