Cisco Prime - create a Fault Alarm for Syslog Messages

Is it possible to generate an alarm for especific Syslog Messges sent to Cisco Prime?
Admin > Network > Notification and Action Settings > Syslog Automated Actions
Here is possible to send an email. But I would like to see the alarm in the Monitoring dashboard.

Hi Leonardo,
unfortunately ,Automated action that you create on syslog will not show in the Monitoring dashboard :(
Thanks-
Afroz
****Ratings Encourages Contributors ****

Similar Messages

Fault name for Rejection Messages in Fault policy.

Hi ,
I am trying to do my fault handling for Rejected messages .I am bit confused what is the fault name i should specify for rejection messages .
Say for BPEL , We have bpelx:binding fault etc for BPEL ..
<faultName xmlns:rjm="http://schemas.oracle.com/sca/rejectedmessages" name="rjm:[?????????????] ">
<condition>
<action ref="writeToFile"/>
</condition>
</faultName>
</Conditions>
Regards ,
Naga

It should be the "service name" for the inbound adapter in the composite. Here is the doc link which explains this: http://download.oracle.com/docs/cd/E14571_01/integration.1111/e10231/life_cycle.htm#TKADP187.
regards,
Sandeep

Cisco Prime Infrastructure 2.0 Alarms (switch port down)

We have a cisco Prime Infrastructure 2.0 managing switches, routers and AP.
By default, when a port of a switch goes down, the cisco Prime Infrastructre generates a Critical Alarm for that. (this is a problem, because every phone of laptop disconnection will generate a critical alarm for me)
I found out that if we go to Administration --> Alarm Severity --> Link down, I can change the Alarm from Critical to another type of alarm.(ex: warning)
The problem is that I want to keep the Critical Alarm for my Uplinks ports and for some important switch ports, and I would like to make the alarm as warning for the normal user ports.
I know that I can create Port Groupping and add ports to each group and apply monitoring templates on those groups. But This couldn't Help me solving my alarm problem.
So I just need to know how to manage the alarms severity for each group of ports.
Thank you

Hi,
Same problem here.
I am using Cisco Prime Infrastructure 2.0 (evaluation version for 60 days). I want to deploy port monitoring for my trunk ports between switches and some other important ports e.g. servers. Basically I want to get alarms when these ports are down, there are errors on ports and etc.
So in Design>Port Grouping I created User Defined group with important ports. In Deploy>Monitoring Deployment I selected Interface Health (default)>Deploy selected Port Groups and when selected port group I created.
Now the rule shows Deployed: Yes and Status: Active. After that I just pulled out one port which was in monitored group, waited 5min as it is set in Interface Health (default) template, and nothing happened, and worse, alarms started to show up of other ports where regular users are connected (computers was turned off), which I do not want to see at all. I tried redeploy template, I even created my own template but still no desired result.
Any suggestions how to make port monitoring work?

Cisco Prime Infrastructure 1.3 Alarm & Events

I am using Cisco PI 1.3 to monitor Cisco 2960, 3750 & 6500 Switchs.
Sometime, when a Switch port is down, a syslog message send to PI and the PI considers this issue as "INFORMATION" Severity level in Events List.
How to make the PI considers the port down issue as "CRITICAL" level in order to raise up an Alarm and send Email Notification?
Thanks & Best Regards

Hello,
Prime Infrastructure considers the alarm based on the severity listed in the syslog message. In this case, the syslog severity is of level 5, hence PI considers the issue as Information.
If you would like to consider these events more severe, the device will have to be configured to generate more severe syslogs for such events.
Best regards,
Vlad
==========
NMS Team
Krakow, Poland
Cisco TAC

Cisco Prime 2.1 CLI-Template for Switch configuration Backup

Hello everybody,
I am trying to write a CLI Template in cisco Prime to save the running-configuration of our core switch to the FTP server,
I have already configured the FTP username and Password in the core Switch
ip ftp username cisco
ip ftp password cisco123
in Cisco Prime I have created a template as follow:
copy running-config ftp:
$FTP_IP_addrress >> the FTP Server
$name >> the name of file and the date
After deploying this template on the core switch,
I received Error Msg in Prime as follow:
Error : Command returned an error : copy running-config ftp: 172.16.30.30 Run_Config_Core_19_2_2015 ^ % Invalid input detected at '^' marker. QAF-DC-4507-CORE(config)#
I know that the backup files can be fetched directly from Cisco Prime in the Configuration Archives, But also I need to test if we can take a backup directly to the FTP server using Prime.
Thanks in advance.

Thank you Bkennedy for replying,
I changed my template to be as follow:
#MODE_ENABLE
copy running-config ftp:
$Mgmt_IP_addrress
$name
#MODE_END_ENABLE
but still I am receiving Error like :
Error : Exception while sending interactive commands to device, Expect timeout: Failed to match expected device output due to Expect timeout current timeout 60000. Current output : Address or name of remote host []? Current expects : (DC-450.{0,30}|DC-4507-AGG)$[^$]+\)#\s*\z DC-4507-AGG#
I believe that we have to tell the Prime how to send the variables to Switch, because the switch is waiting for the remote host IP address and the destination file name???
DC-4507-AGG#copy running-config ftp:
Address or name of remote host []? X.Y.Z.W
Destination filename [dc-4507-agg-confg]?
% VRF table-id 0 not active
% VRF table-id 0 not active
Writing dc-4507-agg-confg !
24425 bytes copied in 1.500 secs (16283 bytes/sec)
DC-4507-AGG#

Can Cisco Prime Infra 2.1 work as syslog server

Hello all,
Customer want Cisco Prime Infra 2.1 to work as syslog server. they want to query text in syslog and get raw log file from Cisco Prime Infra. but when i see in user interface. I think that it cannot query and search text in syslog. but i am not sure whether we can get raw log file per devices from Cisco Prime Infra. Can anyone know about this.?
thanks
sompoj

Hi Sompoj,
In the prime infrastructure Syslogs are directly read from udp port 514 and then filtered
, the non SEV1 and SEV2 syslogs will be dropped and will not be entered into db . The
syslog messages will not be saved into log files .
Thanks-
Afroz
****Ratings Encourages Contributors ****

Does Cisco Prime have a replacement product for NCM or Network Compliance Manager?

Does the Cisco Prime application development team have a product that replaces the NCM or Network Compliance Manager?

Both Prime and LMS can do baseline compliance, after a fashion. LMS's is much more mature in my estimation. Prime is more around the lines of deploying templates.
The regulatory compliance functions as of now are in only LMS's Compliance and Audit Manager (CAAM) function. It's quite useful, matching the baseline compliance features.
An LMS license is included with PI, but it does need to be on its own server (or separate VM).

Prime Infra 2.0 alert when syslog message received

Dear member,
May I know did prime infra 1.3, 2.0 can support alerted user when received a syslog message?
if yes, and configiuration guide for reference?
Regards

Hi Russ,
PI does not actually keep a record of the raw syslog messages it receives, and there is no report for syslogs. When PI receives a syslog, it will immediately process the message and convert it to an event/alarm.
Also, note that PI only processes severity 1 and 2 syslogs. The closest thing you can get to a syslog report
would be to run anadvanced search for events
For other alarms and events you can go to Operate > Alarms
& Events > Email Notification page. Make sure that the alarm categories that you
want to have notifications for also has the Enable checkbox checked.
Thanks-
Afroz
[Do rate the useful post]

Create 2 outbound Idocs for 1 message type

Hi Experts,
We are sending an outbound Idoc of message type DESADV. We would like to trigger 2 Idocs per Shipping Notification.
Could you please help?
Thanks,
Vitish.

Hello Vitish
Each output partner can have it's own output. Also for the same message type. Maybe the 2 DESADV IDOC's are sent to different partners or destinations. But even when not you still can define 2 different output partners for the message type. Then 2 outputs will be triggered for the same message type.
Regards Jack

Cisco Prime LMS 4.1 - Support for Cisco Catalyst 3560-C Series Switches

Hello together
I have a customer which uses the following switch. Last year I have installed LMS 4.1 for him to manage the switches. Unfortunatly the switch model is not supported. According to the information found on the following site the switch is supported for most of the modules in LMS:
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.1/device_support/table/lms41sdt.html
The oid object of the device is the following: 1.3.6.1.4.1.9.1.1465
Supported Software: 12.2(55)EX (Customer has 12.2(55)EX3
Version Support Type: Device Update
So I updated all device updates I was able to find.
Step 1: For that I went to Admin > System > Software Center > Schedule Device Downloads and created a job where I have downloaded the latest versions of all packages.
Step 2: Installed the downloaded packages Admin > System > Software Center > Device Update and installed all the packages.
Unfortunatly I don't see the same result like described in the Supported Device Table for LMS 4.1.
- Cisco View -> works
- Inventory and Config Collection -> works
- Fault Monitor not working -> Error Code Unsupported
- Network Topology Layer 2 Services -> Device Type ciscoProducts.1465, Symbol Question Mark
- VLAN Management -> Doesn't work
- User Tracking > seems also not to work
When I open the report for supported devcies (Reports > System > Device Support) and search for C3560C... I find the following devices, but not mine which i need:
C3560C-8PC-S     .1.3.6.1.4.1.9.1.1466
C3560CG8PC         .1.3.6.1.4.1.9.1.1317
C3560CCG8TC     .1.3.6.1.4.1.9.1.1318
wsC3560CPD8ptS     .1.3.6.1.4.1.9.1.1368
Does anybody have experience with the same switch type / model? Am I doing something wrong or is this type of switch not implemented correctly till now? Further the docuemntation supported devices would be wrong.
Thanks for any feedback Erich

Thanks but I just heard back from my Cisco SE and he assures me that an AP will NOT use up a license.
I've asked him to verify his answer for me.
Is your answer based on real world expereince (the best there is)? That is, are you running Prime LMS 4.1 and does it indeed use up a license for each light-weight AP it discovers & manages?
Thanks for mentioning options 1-3 but I do not wish to employ any of them. I don't mind buying the additional licenses for APs ... I just need to know if I have to or not.
Ian.

Creating a Audible Alarm for ECG data if it surpresses or goes below a certain rate

Once Ive sucessifully processed a ECG singal what is a good way to set up a alerts in the case of the Heartrate exceeding a set parameter or falling below?
Audible or Just a LED turning on is fine.
Thank you!

You need to elaborate on your question. For example:
Who is receiving the alert? Nurse? Doctor?
Where is the nurse/doctor?
Will the alarm be sounded in the patient room?
What are the current working practices at the hospital site?
In general, there is a trend toward using "silent alarms" in hospitals. And also to send alarms directly to the responsible person (rather than just beeping and blinking a light in the hallway). Having loud alarms can disturb patients, especially when there are many of them. Best solution is to sound a silent alarm, but send it to the correct recipient on their handheld device. Don't just flash a light in the hallway that people will assume someone else is responding to. Also "force" the alarm recipient to acknowledge the alarm. This can be done by "annoying" the recipient until they acknowledge (vibrate or increase severity until they respond). Having loud, constant alarms that are not "sent" to a specific owner, and do not require acknowledgement will lead to "alarm fatigue" (when nurses ignore alarms because there are so many irrelevant alarms).

Cisco prime Changing the password lenght for snmp authentication

When i try and put in passwords for the snmp for authorisation and privacy i find that prime infrastructure
wont accept less than 12 characters
How can i change this setting please
It under Configure/switches/(switch)
Steve

When you run the validation job you can capture the traffic via the packet capture utility in device center.
Be sure to filter only to the device being tested or else you will get a really big tcpdump (jet file).
You can open the resulting jet file in Wireshark to look at the transfer deciphered. That will show you exactly what commands are being sent and what reply comes back from the device.

Can we create a SAP report for all messages displayed inRWB

Hi All,
We are planning to create an SAP report (in XI or R/3) which will display the status of all the messages in the XI adapter engine. I wish to know if this is possible and if yes, then can someone throw some light on it.
<b>Scenario:</b><u></u>
Inbound XML messages are coming to XI from legacy system and finally are sent to R/3 from XI.
In R/3 and XI we have SXMB_MONI or SXI_MONITOR to see the overall status of the message pipeline. However if there are some adapter issues, the messages are stuck in the adapter and never get shown on SXI_MONITOR. Only way to see these messages is through RWB.
So can we create a report in R/3 or XI which displays such messages stuck in RWB .
Appreciate your response on same.
Thanks and regards
RK

alerts can be triggered for RWB errors also. So when it is triggered there will be an entry in tables related to alert. from there u can read and make use of it in a table. there are workaorunds which we need to explore. to read the text from sxmb_m,oni there are f/n mod aviable...not able to get one but can be found in debuggin

Cisco Prime Collaboraiton Standard Licenses

Dear Team,
I have a customer purchased Cisco CUWL PRO & Enhanced Licenses for 10,000 Users for Unified CM version 8.0 and now he is asking for upgrade to version 10.5. The question is :
1-since he did reinstatement for different type of licenses and already has the order, Should the customer entitle Cisco Prime Collaboration licenses by default or he has to purchase them separately?
2-Does the customer going to receive Cisco Prime Collaboration Standard (Porvisioning and Assurance only) ?, If so for How many license Users it comes by default?. If less than 10000 ,then how to order the remaining?.
Thanks in advance
Regards,

Prime collaboration standard is free and does not require any licenses. Advanced license is separate from any UC user licenses:
Cisco Prime Collaboration Packaging: Standard and Advanced Options
Beginning with version 10.0, Cisco Prime Collaboration is provided in two different offerings. Cisco Prime Collaboration Standard is included with all Cisco Unified Workspace Licensing and Cisco User Connect Licensing, and Cisco Prime Collaboration Advanced is available for upgrade. The Standard option is only available and compatible with Cisco UC 10.0. The Advanced option supports Cisco UC 8.x - UC 10.x. The Standard option enables provisioning of all voice and video services purchased and fault monitoring across voice and video for a single cluster environment. For deployments that require more advanced management, Cisco Prime Collaboration Advanced offers multi-cluster scale, additional automation, deeper diagnostic capabilities, and long-term reporting. This order guide addresses Cisco Prime Collaboration Advanced only.
Customers who are interested in Cisco Prime Collaboration Advanced may activate the “Advanced Evaluation” from within the Prime Collaboration Standard GUI, for a 60 day term, or may purchase a permanent Cisco Prime Collaboration Advanced. For more information about license installation, please refer to the Cisco Prime Collaboration Quick Start Guide 10.0 posted on Cisco.com under ‘Install and Upgrade Guides.
from:
http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/prime-collaboration/guide-07-729809.html
Chris

Cisco Prime 1.2 - cannot delete "Unassigned" Campus

Hi,
has anybody an idea how to delete Unassigned Campus?
I went through I think all documentation and they are speaking that only "System Campus" cannot be deleted, but not a single word about "Unassigned" campus.
All the campuses below behaves like a child of Unassigned campus. I know it's just cosmetic issue, but still I would like to get rid of it.
I attached a screenshot.
Thanks!
K.

Yes you can add building and floor diagrams in Cisco Prime Infrastructure 1.2. For the same you can see the below link
http://www.cisco.com/en/US/docs/wireless/prime_infrastructure/1.2/configuration/guide/maps.html
Open this link and goto Adding Floor Areas to a Campus Building

Cisco Prime - create a Fault Alarm for Syslog Messages

Similar Messages

Maybe you are looking for