Cisco Prime - Custom Inventory Change Report?

Hi,
Cisco Prime has this report:
Reports > Inventory > 24-hour Inventory Change
The problem is that the Report reports things that I don't want to track, like changes in "NVRAM Used", Interface Speed, etc...
Is it possible to configure Inventory Change so that it would not check some itens?
Thanks.

Thanks for answering,
my report has, for example, the following information:
Changes for Device: router01
Processor Identity: ProcessorID = 3
Attribute Type of Change Time Change Detected Previous Value Current Value
NVRAM Used (KB) Changed 2014-02-21 00:10:00.69 16923 16953
I saw that Syslog Automated Actions > Inventory Fetch has very useful configuratios, but I think that it is still not what I need. The screen you pointed out was related to messages from Syslog that triggers inventory collection.
What I need is in the image below.
All right, NVRAM changed it's current used size. For me, it is completely useless to know about that every day in my Inventory Change report. That information is flooding my report. How to remove it from future reports?
Thanks again!
Message was edited by: Leonardo Machado

Similar Messages

Cisco Prime Infrastructure 1.3 - reports

Hi all,
I am curious if anybody can help me with Cisco Prime reports. What I want to do is to create report of all my devices which will have information such as hostname, IP adress, . . . , an serial number. I found this task almost inpossible... When I look at the device work center tab and click on one of my devices I can see alll of the information I want (so good so far all infromation are available..but..)When I want to create such a report from all of devices in report section I pick up Detail Device Inventory and customize report which I want. Problem appears after report is done. The main ifnormation such as hostname, location an IP adress are in the first part of report and in the second part there are chassis information with serial number and other fields. But these two parts of report dont have any common field so it is impossible for me to match serial number to hostname..So if I dont want to click on every device in device work center and write down all of information I dont know how to do such a simple task...
I hope someone is able to follow my thoughts
Thanks for any answer
Martin

Robert-
If you create a separate service rule, you can have it fork TACACS authentication requests from that specific IP to a different Service identity and authorization process, where you can tell it to select a specific shell profile. Then all you have to do is create a separate shell profile for managing Prime and have that one selected. We do this with our UCS dvices, regular router/switch CLI logins, etc.
So for example:
UCS: TACACS request --> if match service selection rule "from UCS devices", go to UCS admin access policy --> if match ucs admin identiy reqirements, give UCS admin shell profile
PI: TACACS request --> if match service selection rule "from PI devices", go to PI admin access policy --> if match PI admin identiy reqirements (which are same as UCS), give PI admin shell profile
Default: TACACS request --> if match tacacs protocol from our IP range, go to default device admin policy --> if match defaul identy requirements, give default admin shell profile

CISCO PRIME INFRASTRUCTURE NETFLOW TRAFFIC REPORT

Hi,
I have a report from cisco prime infrastructure, that I don´t know how to interpret, because the fields in the report I don´t know what´s mean them, the difference between them, what are optimal values, the worse values, etc.
Can someone help me with this
The name of the report is: FLEX NETFLOW TRAFFIC TQPQ
The fields that I don´t know what are:

hello,
I also have a problem concerning the interpretation of the report that I got. if anyone knows how Cisco gets its premium reports, it will help me!

Cisco Prime Infrastructure 2.1 Custom Reports

Hi, I need to generate a custom Guest User report from Cisco Prime Infrastructure 2.1. It needs to have a couple more fields added to the existing "Guest User Association" report.
Is it possible to connect to the Cisco Prime Infrastructure Database and Generate custom reports? Is there any documentation on this?
Thanks

Programmatic access to PI's data is via the REST API.
Check the help menu on your PI server to see documentation regarding the supported tables and fields that can be queried via that method.

Cisco Prime Rogue AP Report - No Rogues from 3702 Series AP's

I am running Cisco Prime Infrastructure (2.1) that manages a Cisco 5508 WLC (7.6). We have multiple version of AP's managed by this WLC to include 1142, 2602, 3702, etc...In Cisco prime when we run a Rogue AP Report. None of the Rogue AP's discovered by 3702's are displayed in the report. The Rogues show on the WLC though from all AP's. Cannot find a reason for this. Any ideas?

The Rogue alarm state always stays on "removed" once deleted
CSCuo91446
Description
Symptom:
Once one of the alarm of rogue AP is deleted the newer rogue AP alarm changed to removed state even for different mac address.
Because of the removed state the detecting AP which detected the rogue is not displayed
Conditions:
1) Auto SPT is turned on
2) Prime 2.0 or 2.1
Workaround:
Click on refresh from network for each alarm in removed state or disable auto spt
Last Modified:
Jun 30,2014
Status:
Fixed
Severity:
3 Moderate
Product:
Cisco Prime Network Control System Series Appliances
Known Affected Releases:
(1)
2.1(0.0.1)

Cisco Prime Collaboration Assurance IPPhone 3901 no serial number report

Hi All,
I have installed Cisco Prime Collaboration Assurance in my office and try to create phone inventory report , so far no problem , but when i add IPPhone 3901 there no serial number in the report , I have enable web access on the phone , i can see the serial number by click the IP .
any help ?
Best Regards,
Tommy

How can I get CDP neighbor information from access point reports in Cisco Prime 2.0

How can I get CDP neighbor information from access point reports in Cisco Prime 2.0? I have looked through all the reports and I cannot find a report that gives me the CDP neighbor information of an access point. I thought that information was in there, however I cannot seem to find it.
Thanks in advance!

Hi
You can get this from an inventory report in PI (Select Report Type AP). Here is an example of PI 2.1 works for me. Once you export this into excel you can sort based on controllers & filter the single controller connected AP you want.
Regards
Rasika
**** Pls rate all useful responses ****

Cisco Prime Infra 2.2 + Third Party Inventory and configuration backup

Hi All,
I am having a doubt related to Cisco prime solution capability to do a discovery and config backup for non-cisco devices.
Requirement is to use Cisco prime to do a discovery, inventory and take configuration backup for non-cisco devices. Is it something possible out of the box ?
If not possible out of the box, is there any method to do that using any custom API ?
Can we monitor 3rd party( Non-cisco) devices using Cisco Prime 2.2 ?
Skr

Hi,
Below is supported-device list, check if your device is listed there.
http://www.cisco.com/c/en/us/support/cloud-systems-management/prime-infrastructure/products-device-support-tables-list.html
- Ashok
Please rate the post or mark as correct answer as it will help others looking for similar information

Cisco Prime Infrastructure 2.1 Inventory Job

My cisco prime infrastructure performs a switch inventory job every night at 22:00 hrs. When I looked at the syslog of the devices in the inventory, I see some entries that I never saw with other LMS versions.
2014-06-30 22:00:01   Local7.Notice   xxx.xxx.xxx.xxx   5410: Jun 30 22:00:00.623 CST: %SYS-5-CONFIG_I: Configured from xxx.xxx.xxx.xxx by snmp
2014-06-30 22:00:01   Local7.Notice   xxx.xxx.xxx.xxx   5411: Jun 30 22:00:01.567 CST: %SYS-5-CONFIG_I: Configured from console by vty1 (xxx.xxx.xxx.xxx)
2014-06-30 22:05:10   Local7.Notice   xxx.xxx.xxx.xxx   5412: Jun 30 22:05:09.008 CST: %SYS-5-CONFIG_I: Configured from console by vty0 (xxx.xxx.xxx.xxx)
I don't understand what the PI is doing with the switches. Does anyone know what is happening during this inventory background job? TIA

Hello all,
we have the same problem maybe; Cisco Prime IF 2.1 is changing the running-configs and produces out-of-syncs ;
it turns so for us is, as if Cisco Prime IF 2.1 a snmp-server host x.x.x.x community entry writes in the running-config,
so are running-and startup-config are out-of-sync; is this correct? Herbert

Change Interface availability threshold from Cisco Prime Infrastructure 2.0

Dear Community,
I’m working in Cisco Prime Infrastructure 2.0 and I’m having the following problem:
I want to monitor the interfaces availability from all the devices of my network. But only makes sense send an email notification for the most critical interfaces. I don´t want to receive an email notification every time anyone unplugs the network wire.
How can I achieve this?
I already tried to change the interface availability threshold from the Interface Health Threshold Template, but this one isn´t available to configure.
The idea was to change the severity of the alarm so I could distinguish what type of alarm would send email notification.
I also created a Custom SNMP Template that gets the ifOperStatus using the MIB IF-MIB. This also didn’t work because Prime Infrastructure doesn’t allow me to define thresholds to a Custom SNMP Template.
Without threshold, no alarm, without no alarm, no email notification!
Can you help?
Regards,
Daniel CJ

Only on the HA pair which would be the secondary.
High Availability (HA) RTU: If Cisco Prime Infrastructure is deployed in a high availability configuration with one primary and one secondary instance in an HA pair, then an HA RTU is required. You only need to purchase a single set of the regular licenses (for example, Base, Lifecycle, and so on) for the primary instance.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Cisco prime infrastructure 2.0 inventory SFP

hello,
anyone knows if it is possible with cisco prime infrastructure 2.0 create inventory to obtain data from SFP (serial number and model)?
thank you

Hi ,
Can you try the below report and see if you are able to see the information , you are looking for
Report > Report Launch Pad > Device > Detailed Hardware
Thanks-
Afroz
***Ratings Encourages Contributors ****

Custom Net Change Booking Report

Friends,
I am in the process of creating a Custom Net Change Booking Report.
The Report should show the changes that affect the sale order Bookings.
The Audit history capture the changes but it stores two lines for each change.
Main Constrains are:-
* Order Lines getting splitted should not be consider since it will not affect the total quantity.
* Qty Change, price adjustment and the New lines created to the sales order should be considered.
Following is the query i tried.
The main issue in the query is if an order line is getting changed for qty and price at the same time it is not showing the changes correctly.
Any help is appreciated.
SELECT a.hist_creation_date, b.hist_creation_date,
TO_CHAR (a.order_number) order_number, a.header_id, a.line_id,
b.new_attribute_value - b.old_attribute_value net_qty_change,
0 net_price_change, a.hist_type_code,
'QTY UPDATE/CANCEL' type_of_adjustment
FROM oe_order_lines_audit_v a, oe_audit_attr_history b
WHERE b.entity_id = 2
AND a.line_id = b.entity_number
AND a.HIST_CREATION_DATE = b.HIST_CREATION_DATE
AND hist_type_code NOT IN ('SPLIT')
AND attribute_id IN (1230) -- Quantity Change
AND b.reason_code IS NOT NULL
UNION ALL
SELECT --DISTINCT
/* -- Type Of Price Adjustment */
a.hist_creation_date, b.hist_creation_date,
TO_CHAR (a.order_number) order_number, a.header_id, a.line_id,
0 net_qty_change,
b.new_attribute_value - b.old_attribute_value net_price_change,
a.hist_type_code, 'PRICE ADJUSTMENT' type_of_adjustment
FROM oe_order_lines_audit_v a, oe_audit_attr_history b
WHERE b.entity_id = 2
AND a.line_id = b.entity_number
AND a.HIST_CREATION_DATE = b.HIST_CREATION_DATE
AND attribute_id IN (1316) -- Price Adjustment
UNION ALL
SELECT
/* New Line */
wsh.creation_date, wsh.creation_date,
wsh.source_header_number order_number,
wsh.source_header_id header_id, wsh.source_line_id line_id,
wsh.requested_quantity net_qty_change, 0 net_price_change,
NULL hist_type_code, 'NEW LINE' type_of_adjustment
FROM wsh_delivery_details wsh
WHERE 1 = 1
AND wsh.source_line_id NOT IN (SELECT entity_number
FROM oe_audit_attr_history a
WHERE 1 = 1 AND entity_id = 2)
AND wsh.split_from_delivery_detail_id IS NULL
Thanks
Karthik

Sandeep,
Thanks for the reply i am in Oracle Application release 12.0.4 and I could not find the view oe_order_lines_all_ac1 in this version.
I appreciate your help.
Thanks
Karthik

Cisco Prime Infrastructure 2.1 Not generating reports

Dears,
I am new to Cisco Prime. I installed Cisco Prime Infrastructure 2.1 for 60-days evaluation and i added routers, switches and APs. I configured SNMP community and telnet credentials. I can see clients on Dashboard, but when i go to reports and generate them for last hour, it displays "None Detected".
Please advise.

Programmatic access to PI's data is via the REST API.
Check the help menu on your PI server to see documentation regarding the supported tables and fields that can be queried via that method.

"Busiest Clients" report template on Cisco Prime & Aironet 1242AG

Yesterday I was trying to schedule a "Busiest Clients" report on our Cisco Prime physical appliance (PRIME-NCS-APL-K9, v2.1.0.0.87).
My goal was to monitor the busiest clients on a couple of old Aironet access-points. These APs have been installed in a branch office of our university that rely on 4 Mb/s SHDSL WAN connectivity and, as you might imagine, some saturation occurs when the classrooms are crowded.
Unfortunately, all the reports were empty ... there was only a "No data matches the specified criteria for the report” warning inside.
The Client Statistics task (Administration>Background Tasks) was enabled and I was able to run this report selecting a different floor area ... after a few tries I've discovered that this error occurs only when the old Aironet 1242AG APs are involved. If I select a floor area populated with the newer 1142 and 2602 models, the report template works as intended.
So, is there a way to fill a "Busiest Clients" report with data fetched from our old Aironet 1242AG APs?
Our WLC is a Cisco Wireless Services Module 2 Controller for Cisco Catalyst 6500 (WS-SVC-WISM2-K9).
(Sorry ... my English is a bit rusty)

Hi,
Kindly try to restart the Dameon manager with the command line of the server
1> net stop crmdmgtd
and then start the daemon manager --> net start crmdmgtd (wait for atleast 20-25 minutes before login back to LMS and also see if any file do exist at location CSCOps\Objects\dmgtd\ready folder).
Get the output of pdshow after waiting for 20 minutes and stdout.log and stderr.log from CSCOpx\MDC\tomcat\logs.
Many Thanks,
Gaganjeet

Cisco Prime infrastructure Change severity Switches and hubs - link down alarm

Hi, I want to change the severity of the link down alarm in the Cisco Prime Infrastructure 1.3, but in the menu Administration -> System Settings -> Severity Configuration i can not find the alarm. Some body knows where is it? o where i can change the severity of that alarm?
Thanks in advanced.

Hi Rollin and Daniel,
the first test i did changing the severity was with a new installation, with no devices added and it worked, when i did it in a Prime infrastructure with devices added it didn´t work, well, for this Prime with devices i upgraded it with the patch for 1.3 version and now it works too, the alarms is ok as the alarm severity, this is the link for the patch:
http://software.cisco.com/download/release.html?mdfid=284652876&flowid=38562&softwareid=284272933&release=1.3.0&relind=AVAILABLE&rellifecycle=&reltype=all
i hope this helps,
Regards,
Milton Tizoc.

Cisco Prime - Custom Inventory Change Report?

Similar Messages

Maybe you are looking for