Cisco Prime Infraestructure email notification

Hello,
We have configured Cisco Prime Infraestructure to get email notifications. Problem is that we are getting alerts for all controllers and APs
configured in Prime, and some of them are managed by another team, so I would like to know if it could be possible to configure some kind
of filter to get the alerts only for controllers we are interested?
Any ideas would be very much appreciated.
Jhony Pardo

Hi Scott
I have not a good understanding how virtual domain it can helps. How do you suggest using virtual domains?
In my case there are only three administrators in the network and they are not interested about getting email notifications from the ports connecting end users in access switches, but they are interested about uplink ports notifications and CPU, memory, environment from the same switches.
Hope your support.
Marcelo

Similar Messages

Cisco prime infraestructure 2.X

Hi,
Two questions..
it's posible management, inventory,etc.. switch 2960x/6509 vs-2T-10g, with cisco prime infraestructure 2.x?
it's posible report with compliance licence switch 2960x?
Thanks

Cisco Prime Infrastructure 2.0 Supported Devices
http://www.cisco.com/en/US/partner/products/ps12239/products_device_support_tables_list.html
For 2960s - See rows 465 to 488
For 6500s - See rows 266 to 281
There are limited compliance reports available in 2.x Prime Infrastructure for wireless and wired devices- Please see::::
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/user/guide/reps.html#wp1059921

Cisco Prime Infraestructure 1.1 (R-PI-1.1-K9)

Hello everybody, i have a license for CPI 1.1, i need install it, but at download page there is no such version, just CPI 1.2, where can i download 1.1 version?
This license was bought three months ago.
Thank you.

Thank you Rob, i found this link
http://www.cisco.com/cisco/software/release.html?mdfid=284206374&release=NCS%201.1.1&flowid=30982&softwareid=283927263
I started the download.

Cisco Prime Infraestrutre 2.0 - JOB Not ends

Hi,
i've a problem in my Cisco prime Infraestructure, i've scheduled a IOS upgrade with a reload in the end, i forgot to permit in the equipment to do reloads from SNMP, and the question is all the job was done except the reload, bu in Jobs dashboard i still seeing that the job is in progress anda i can not abort the process.
Anyone kows ow can i clean this job, from the job list, and why this happens?

Hi,
i've alreay added the snmp-server command.
With Job i still have problems, qhen i try do abort the job i've the follwing error:
"Selected jobs were not aborted. FAILURE : Exception occured while aborting the job : Job with job id 2752679 does not have any running cancellable tasks.-JOBM_042"
The cancel option isn't enable.

Question of Cisco Prime

Hi everybody.
I have one question about cisco prime infraestructure, i whish to know how the Cisco Prime control the link WAN of my enterprise.
the topology is:
ROUTER --> MODEM --> ISP
I supossed that CP must have the assurance lincense, for use the control with netflow, but i whish to know how i can monitored the link between the modem and the ISP with the cisco prime.
i can monitored the link with the soft. Intermapper, i whis to know if the Ciso Prime 1.2 could perform this action.
Regards

Well the situation is like this... I am monitoring several wireless network devices. Some are connected by 3G and others via some other technology.
As you probably already know wireless connections are situational. Sometimes they work and sometimes they don't. What I want to achieve is to reduce the number of false positive alarms from these devices.
The current plan is to increase the timeout to the maximum (60 seconds) and the number of retries to a high enough number to make false positives statistically unprobable.
I would still like the devices to get polled quite often for a quick response, for example each 4 minutes (240 seconds).
The optimal situation would be the following:
Poll repeatedly each 4 minutes...
For each successful poll, the timer resets and after 4 minutes another poll happens, except for when the poll is not successful. When this happens no new polling instances get started and the polling instance that failed continues with a timeout of 60 seconds for X number of repetitions.
As soon as one of the retries is successful, the timer resets and in 4 minutes time a new polling instance gets created anew. If however after all of the retries, the device still fails to respond to the polls an alarm should get created and in 4 minutes time, it's time to check if the connectivity has been restored.
Hopefully the image is a little clearer now... This is why I'm interested in understanding if new polling instances get started independently or not.

How to customize email notifications sent by Cisco Prime.

Hi,
We have been receiving email alerts for any unresponsive devices in Cisco Prime. I was able to find the option to customize the subject for such email alert under Admin-Network-Notification and Action settings, however I am not able to locate the option to change the email body.
The email body for such alerts has lot of unrequired information which I would like to remove.
Can someone provide me the options on how to get rid of such information in the email body.
Regards

Hi ,
To customize the e-mail subject:
Step 1 Select Admin > Network > Notification and Action Settings > Fault - Email subject customization.
The available and selected lists of the subject attributes for e-mail are displayed.
To customize the e-mail subject, you can add and remove subjects from the current e-mail subjects list. By default, following list of e-mail subject attributes are displayed in the Selected Subjects for E-Mail box.
•Event ID
•Device Name
•Time
•Severity
•Event Name
•Status
To add a subject:
a. Select the subject attribute from Available Subjects for E-Mail.
b. Click Add.
The selected subject attribute is added to the Selected Subjects for E-Mail list.
You can add a subject attribute only from the Available Subjects list to the Selected Subjects list. You cannot add a subject attribute from the Selected subject list to the Available Subject list.
To remove a subject attribute:
a. Select the subject attribute from Selected Subjects for E-Mail.
b. Click Remove.
The selected subject attribute is removed from the Selected list and added to the Available subjects for E-Mail list.
You can remove a subject attribute only from the Selected Subjects list and not from the Available Subjects list.
Step 2 Click Up or Down to rearrange the order of the selected e-mail subject attributes.
Step 3 Click Apply to save the customized e-mail subject attributes.
Note: Other than this you will not be able to customize any thing, User-defined fied option will not work.
I hope this will help
Thanks
Afroz

Email notification for config deployment jobs in Cisco Prime Infrastructure 1.2 ??

We're upgrading from LMS 3.2 to Cisco Prime Infrastructure ...
In LMS 3.2 we're using netconfig all the time to configure various jobs related to port security
In installing Cisco Prime Infrastructure and working through it's use of templates, I'm having some difficulty finding out how to send out a notification once a configuration job has completed. It's so simple in LMS 3.2 since it's part of the job creation screens.
Any assistance would be greatly appreciated.

HI, Raymond
Just wondering if this problem is resolved?
Thanks!

Email Notifications on Prime Infrastructure 2.1

Hi Everyone,
I have a Cisco Prime Infrastructure 2.1 with almost 100 switches registered and managed properly. I have configured the Mail Server and alarm notifications are sent with no problems.
The deal is that I don´t want to recieve alarm mails for every single device that is registered. Is it possible to recieve mails just for a group of devices? I was checking the Cisco documents but could not find something clear about this.
Thanks for your help,
Ricardo

Hi Everyone,
I have a Cisco Prime Infrastructure 2.1 with almost 100 switches registered and managed properly. I have configured the Mail Server and alarm notifications are sent with no problems.
The deal is that I don´t want to recieve alarm mails for every single device that is registered. Is it possible to recieve mails just for a group of devices? I was checking the Cisco documents but could not find something clear about this.
Thanks for your help,
Ricardo

Syslog Email forwarding on Cisco Prime Infrastructure

Hi everybody,
We are performing a migration from LMS 4.2 to Prime Infrastructure 2.1 and we are realizing that some features are not in this new platform.
I suspect that one of them is syslog forwarding by email. In our old LMS we collect some syslog messages, we filtrate them and we email some of them, based on a criteria. Some of them we email to someone, and some of them are droped.
Does someone know if this feature is avaliable in Cisco Prime? I think we can collect syslog messages and view them, but we can not process. Am I right?
Regards and thank you in advance,
David

Hi David,
Yes , unfortunately so far syslog forwarding is not supported.
Also so far only SEV 0.,1 and 2 syslogs are supported in PI. Hoping to have these features in PI 2.2
Thanks-
Afroz
*****Ratings Encourages Contributors ****

Logo in Guest Email Notification(Cisco ISE sponsorportal)

Hello Everyone,
I have some questions regarding ( via Cisco ISE sponsore portal) Guest email notification:
Right now we have this kind of structure for Guest email notification:
Welcome to the XYZ Guest Portal.
Your guest account details:
Username: aefgh
Password: 4Z7Pk
Valid From: Mon Sep 30 10:15:45 CEST 2013
Valid To: Mon Sep 30 18:15:45 CEST 2013
Thanks
Now I want to add my company logo in this notification.(Email as well as in print format).
Can anybody help me to solve this.
Thanks

Please check the below link this may can be helpful for you:
Link-1
http://www.cisco.com/en/US/docs/security/ise/1.0/user_guide/ise10_guest_pol.html

Cisco 5508 Email Notification

I have 2 Cisco 5508 Wireless LAN Controllers.
They are NOT connected to a WCS.
Is there a way to confiure the 5508's to send email notifications when an AP drops off line?
Is not is this functionality available with either a WCS or new NCS?

Hi,
You can't send SMTP alerts directly from the controllers.
The options you have are
to configure a Syslog server under the Management tab of the controller to enable logging of alarms to the Syslog server. When the alarm arrives at the syslog server, there needs to be an event configured to email the particular alarm to SMTP recipients
Install WCS at version 7.x providing support for the 5508 controllers and 350x WAPs. Via WCS, with the controllers and WAPs managed by the application, the alarms will be emailed to the configured SMTP recipients
Hope this is of help
Regards
David

Performance Notification Message Customization in Cisco Prime LMS 4.2.4

Greetings,
I'm attempting to deploy Prime LMS 4.2.4, and one of the features I would like to use is performance threshold notifications. However, the email notifications are bloated with information, and I'm unable to find a way to customize them, unlike the fault notifications.
I'm hoping someone will be able to point me toward what I've missed, and I thank you for your time and consideration.
Regards,
Rob

Hi Mantej:
Thanks to your link and I have downloaded the Prime LMS 4.2 document.
I then read and installed the JRE first in 64 bits because my Windows OS is 64bits but it still prompts out the Java installation screen. I then installed the JRE in 32 bits.
After that, it has no more Java installation screen. It then request for downloading file at the Windows top bar. I follow the request to riight click to allow the downloading. The Java running and downlaod the file.
After that, I cannot see any difference. Meaning I still cannot access anything for Toplology Services to draw my network topology diagram.
May I know what should be happen and what is the next step to do the topology drawing?
Many thanks!
Regards,
tangsuan

Cisco prime guest user email

hello
when adding a guest in the cisco prime there is a option that you can print or email the user details.
is it possible to change the print page and the email that is send.
a need to add other picturen and change the template of the email and printing
thanks

Hello,
The logo on the page which would be printed with the guest user credentials can be customized. It can be done from:
Administration > Users, Roles & AAA > Users > Click on the User name for 'Lobby Ambassador' > Click on the 'lobby Ambassador Defaults' tabs & scroll down to see the 'update Logo' option.
The details of the emails/credentials format can't be customized.
Ram.

How to config Email notification on Cisco DCNM 7.0.2

Hi everyone !
I found that Email notification can configured from : Admin > Events > Forwarding
There are 2 options : SMTP Address and Email Address . But there is no option for Email Password
How can i use my Email to send notification to any other Email without my Email password ?

hello - I have just moved your post to the Topic forums - you had posted your question in an obscure, non-visible, promotional community. Hopefully our community users will see your question now

Cisco Prime Infrastructure 2.1 error-disable alert

We have a cisco PI 2.1 managing switches and a lot of switchports have BPDUGuard enabled. When occur error-disable , request send email notification to administrator .
By default, when a port of a switch goes down, the Prime generates alarm for that. (this is a problem, because every laptop disconnection will generate alarm for administrator)
Can i change the alert just for error-disable and how to ?
Thanks

Causes of Errdisable
This feature was first implemented to handle special collision situations in which the switch detected excessive or late collisions on a port. Excessive collisions occur when a frame is dropped because the switch encounters 16 collisions in a row. Late collisions occur after every device on the wire should have recognized that the wire was in use. Possible causes of these types of errors include:
A cable that is out of specification (either too long, the wrong type, or defective)
A bad network interface card (NIC) card (with physical problems or driver problems)
A port duplex misconfiguration
A port duplex misconfiguration is a common cause of the errors because of failures to negotiate the speed and duplex properly between two directly connected devices (for example, a NIC that connects to a switch). Only half-duplex connections should ever have collisions in a LAN. Because of the carrier sense multiple access (CSMA) nature of Ethernet, collisions are normal for half duplex, as long as the collisions do not exceed a small percentage of traffic.
There are various reasons for the interface to go into errdisable. The reason can be:
Duplex mismatch
Port channel misconfiguration
BPDU guard violation
UniDirectional Link Detection (UDLD) condition
Late-collision detection
Link-flap detection
Security violation
Port Aggregation Protocol (PAgP) flap
Layer 2 Tunneling Protocol (L2TP) guard
DHCP snooping rate-limit
Incorrect GBIC / Small Form-Factor Pluggable (SFP) module or cable
Address Resolution Protocol (ARP) inspection
Inline power
Note: Error-disable detection is enabled for all of these reasons by default. In order to disable error-disable detection, use the no errdisable detect cause command. The show errdisable detect command displays the error-disable detection status.

Cisco Prime Infraestructure email notification

Similar Messages

Maybe you are looking for