Cisco Prime Infrastructure 1.2 and Aironet 1250 + VSS issues

Hi,
I am new to the NCS implementations and configurations. I have one very specific case with Cisco Prime Infrastructure 1.2 and autonomnous APs and several issues with Cisco VSS on 6500 switches.
So here is the version from Prime:
NCS/admin# show version
Cisco Application Deployment Engine OS Release: 2.0
ADE-OS Build Version: 2.0.1.038
ADE-OS System Architecture: x86_64
Copyright (c) 2005-2010 by Cisco Systems, Inc.
All rights reserved.
Hostname: NCS
Version information of installed applications
Cisco Prime Network Control System
Version : 1.2.1.012
IOS version on our APs (which are autonomnous) is:
AP-N-1>show ver
Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(25d)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 11-Aug-11 03:23 by prod_rel_team
Well the issue what we have now is that access point has been added but its not recognized by the NCS prime. I have tried all three versions of SNMP but I get the same result. The SNMP configuration is valid since I use the same for my switching infrastructure. When I enter "debug snmp packets" and "terminal monitor" I can see the SNMP communication between Prime and Aironet 1250 which is standalone.
When I switch to Lifecycle theme and go to Operate > Device Monitor Center I see all devices I have added. The Aironet 1250 is reachable but under collection status I get Managed with Warnings. When I hover over with my mouse I get "None available".
I have successfully added my switching infrastructure in total, which is operating perfectly for Catalyst 2960/3650/3750/4500 series but for 6500 under VSS I have some warnings. The device is recognized by the system which is excellent and all is operational. I get the following errors under Collection Status:
feature_sensor
SNMP request timed out
feature_powerSupplyFanStatus-6k
SNMP request timed out
IdentityCapability
The device is unreachable.
feature_flashdevice
SNMP request timed out
sam_ipsla_feature
The device is unreachable.
What can be done to resolve these issues ? I have attached a screenshot of this particular issue. The affected access point is 172.16.165.241.
Predrag Petrovic

Hi rajeeshp,
Currently I am not allowed to upgrade it because of internal procedures involved in upgrading a specific piece of software (obtaining permissions from various departments). Is it free to upgrade from 1.2 to 1.3 or there is a specific charge for that.
Predrag Petrovic

Similar Messages

Cisco Prime Infrastructure 2.0 and Cisco ASA

Hello,
We've recently installed trial version of Cisco Prime Infrastructure 2.0 Express. We hoped that it already supports Cisco ASA 55xx series (especially 5505, we have pretty amount of them). But we had some problems with PI and asa durind the exploitation process.
First, I've added ASA to PI, and Inventory Collection Status is Completed, but I can't see CPU and RAM utilization graphs. Inventory.logs are non-informative.
Also, config backup is success, but when I try to watch the backuped configuration at Configuration Archive PI says "Failed to fetch raw configuration". And so on.
ASA version is 5505, image is 9.1(2).
So, I have a question: is it possible to manage ASAs with PI 2.0?
UPD: I've just tried to upgrade asa to 9.1(4), and behavior of the equipment is quite the same. Seems we shall wait for 9.2 to be released.

Have you downloaded and applied the latest Device Pack updates?
PI enhanced ASA support after the initial 2.0 release and the Device Packs incorporate that change.
The README file for Device Packs explains how to install them. (A bug currently does not allow the direct download in PI so you need to follow the method for installation from local storage after you manually download. Here is a link to the download location.

Cisco Prime Infrastructure 2.0 and IPAM Solution

Hello everyone,
I'm student in a big company and my manager gave me a mission to study an IPAM solution.
In 3 month, we will use Cisco Prime Infrastructure 2.0
I turn to you cause I saw on this doc (link below) that CP Infrastructure 2.0 includes an IPAM Solution.
http://www.cisco.com/en/US/prod/collateral/netmgtsw/ps6491/ps11433/ps11480/ps11609/c45_658846_02_prime_aag.pdf
This IPAM Solution, is it just a repository to manage IP Adresse and DNS ?
Is it possible to write on DNS bind with IPAM of CP Infrastructure 2.0 ?
Thank you for your attention,
Cordially Vincent Malique

Pas de problème Vincent.
The Network Registrar product is usually seen only in very large enterprises or service providers as it is designed to sale up to serving hundreds of thousands of addresses.
In smaller organizations looking to move beyond the spreadsheet method of keeping track of subnets, I have seen people have success with IPPlan (open source). Those wishing more functions and a supported product often go with SolarWinds IP Address Manager (IPAM) product.

Cisco Prime Infrastructure 2.0 and ASA 55xx platform problem

Hello,
We recently upgraded to Prime Infrastructure 2.0 with the hope being able to manage our ASA's from PRIME (and complete an LMS migration).
When I attempt to add ASA's to prime i get the following collection errors:
Unable to collect processor and RAM information.          Processor and RAM information.          Unexpected error. See the log file inventory.log for details.
In the logfile I get the following XML parsing error on the MIB:
<palError>
<deviceId>6284310032</deviceId>
<code>VALIDATION_ERROR</code>
<message>Failed to validate output XML: cvc-maxInclusive-valid: Value '3484331296' is not facet-valid with respect to maxInclusive '2147483647' for type 'int'.</message>
<result>
    <result xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="/CISCO-MEMORY-POOL-MIB/xmp-im-file-system-module.xsd">
      <xmp-im-file-system-module>
        <MemoryPoolStatistics>
          <memoryPoolIndex>1</memoryPoolIndex>
          <free>4294967295</free>
          <largestFree>4294967295</largestFree>
          <used>3484331296</used>
        </MemoryPoolStatistics>
To me it seems that the ASA returns a value that is bigger then int32 and thus causes an overflow? Any clues? Workarounds to add an ASA to Prime without checking these MIB'S?
Regards,
Marcel

Hi,
does anyone happen to know if that problem is fixed? My currently setup looks like this:
1. Cisco Prime Infrastructure 2.1 with updated device pack.
2. Assurance license
3. ASA5510 which has enabled netflow. Netflow is being sent to Cisco Prime 2.1
I do receive netflow raw data within Cisco Prime 2.1 but any graphical display of netflow data is not working. Does anybody has an idea where the problem is? Could it be that the graphical data is only displayed when sending netflow 1, netflow 5 or netflow 7?
regards
Maurus

Cisco Prime Infrastructure EoL/EoS and PSIRT reports

Hi
does PI 2.0 support these reports?
I have a trial version of 2.0, but can't seem to find these reports. In the release notes, it says these are supported?
New Features and Enhancements
•Support for End-of-Sale/End-of-Life Lifecycle Management reports for hardware, software and modules.
•Support for PSIRT reports detailing devices impacted by Cisco security advisories.
Any idea how to run these reports?
Thanks for your help

Hi There,
I'm not sure if we are talking about the same thing, but we are running Prime Infrastructure 2.0. (2.0 (2.0.0.0.294))
You have to enable compliance from the settings (restart) and if you look under Report / Report Launch Pad, in the menu on the left is Device, click on there and you will see EOX ...... I've only had a quick look at the reports, but looks to work.
HTH
Simon

Cisco Prime Infrastructure 2.0 and ASA 55xx platform

Hello,
We recently upgraded to Prime Infrastructure 2.0 with the hope being able to manage our ASA's from PRIME (and complete an LMS migration).
When I attempt to add ASA's to prime i get the following collection errors:
Unable to collect processor and RAM information.          Processor and RAM information.          Unexpected error. See the log file inventory.log for details.
In the logfile I get the following XML parsing error on the MIB:
<palError>
<deviceId>6284310032</deviceId>
<code>VALIDATION_ERROR</code>
<message>Failed to validate output XML: cvc-maxInclusive-valid: Value '3484331296' is not facet-valid with respect to maxInclusive '2147483647' for type 'int'.</message>
<result>
    <result xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="/CISCO-MEMORY-POOL-MIB/xmp-im-file-system-module.xsd">
      <xmp-im-file-system-module>
        <MemoryPoolStatistics>
          <memoryPoolIndex>1</memoryPoolIndex>
          <free>4294967295</free>
          <largestFree>4294967295</largestFree>
          <used>3484331296</used>
        </MemoryPoolStatistics>
To me it seems that the ASA returns a value that is bigger then int32 and thus causes an overflow? Any clues? Workarounds to add an ASA to Prime without checking these MIB'S?
Regards,
Marcel

The X series (all with 64-bit SMP images) are not currently supported by PI 2.0. We can hope for a device update in the coming months to remedy that situation.
If you click on the arrow next to the help icon in the top right of your PI and choose "Device Level Support" you will see:
Cisco ASA-5500 Series Adaptive Security Appliances
Features :
Topology
LLDP Neighbor Discovery
CDP Neighbor Discovery
Configuration
Configuration Archive
Software Image Management
Monitoring
Device Availability
Reachability
Inventory
Physical
System - Memory Pools
Interfaces - IP
Interfaces - Ethernet
Device Type
SYSOIDS
S/W Version
Software
Cisco ASA-5510 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.669
OID:1.3.6.1.4.1.9.12.3.1.3.447
Cisco ASA-5510 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.773
Cisco ASA-5520 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.670
OID:1.3.6.1.4.1.9.12.3.1.3.448
Cisco ASA-5520 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.671
Cisco ASA-5540 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.672
OID:1.3.6.1.4.1.9.12.3.1.3.449
Cisco ASA-5540 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.673
Cisco ASA-5560 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.12.3.1.3.454
Cisco ASA-5550 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.753
Cisco ASA-5550 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.763
Cisco ASA-5505 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.745
OID:1.3.6.1.4.1.9.12.3.1.3.560
Cisco ASA-5580 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.914
Cisco ASA-5585 Adaptive Security Appliance
OID:1.3.6.1.4.1.9.1.1194
OID:1.3.6.1.4.1.9.1.1195
OID:1.3.6.1.4.1.9.1.1196
OID:1.3.6.1.4.1.9.1.1197
Cisco ASA-5585 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.1198
OID:1.3.6.1.4.1.9.1.1199
OID:1.3.6.1.4.1.9.1.1200
OID:1.3.6.1.4.1.9.1.1201
Cisco ASA-5585 Adaptive Security Appliance System Context
OID:1.3.6.1.4.1.9.1.1202
OID:1.3.6.1.4.1.9.1.1203
OID:1.3.6.1.4.1.9.1.1204
OID:1.3.6.1.4.1.9.1.1205
Cisco ASA-5580 Adaptive Security Appliance Security Context
OID:1.3.6.1.4.1.9.1.915
Cisco ASA-5580 Adaptive Security Appliance System Context
OID:1.3.6.1.4.1.9.1.916

Ask the Expert: Cisco Prime Infrastructure - Implementation and Deployment

Welcome to the Cisco Support Community Ask the Expert conversation.
This Ask The expert Session will cover questions spanning Cisco Prime Infrastructure on Implementation and Deployment on Wired and Wireless. This will be more specific to Customer’s and Partners questions product covering PI on configuration, Features and Menu, Network Monitoring, Maps, Implementation, High Availability and Maintenance and t/s parts.
Monday, February 2nd, 2015 to Friday, February 13th, 2015
Dhiresh Yadav is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco Prime Infrastructure and Cisco Wireless products. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS) and CCIE (DC) certifications.
Afroz Ahmad is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS),CCIE (DC), and SCJP (Sun Certified Java Professional )
Vinod Kumar Arya is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 8 years of industry experience working with large enterprise and service provider networks. He also holds VCP 5 and RHCE certifications.
** Remember to use the rating system to let the experts know you have received an adequate response.**
Because of the volume expected during this event, the experts might not be able to answer every question. Remember that you can continue the conversation in the Network Infrastructure community, > Network Management, shortly after the event. This event lasts through February 13th 2015. Visit this forum often to view responses to your questions and those of other Cisco Support Community members.

Hello Wilson,
Thanks for joining us.
1841 should just work fine for net flow . Hope you have a valid "PI Assurance license" installed on the server.
"PI Assurance license" is required for "net-flow" feature
Devices supporting Netflow in PI ::
1400, 1600, 1700 & 1800
2500, 2600 & 2800
3600, 3700, 3750 & 3800
4500 & 4700
AS5300 & 5800
7200, 7300, 7400 & 7500
Catalyst 4500 ASCI
Catalyst 5000, 6500, & 7600 ASCI
ESR 10000 ASCI
GSR 12000 ASCI
Cisco IOS Software Release Version
Supported Cisco Hardware Platforms
11.1CA, 11.1CC
Cisco 7200 and 7500 series, RSP 7200 series
12.0
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series
12.0T, 12.0S
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8600 series
12.0(3)T, 12.0(3)S
Cisco 1720, 2600, 3600, 4500, 4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)T
Cisco 1400, 1600, 1720, 2500, 2600, 3600, 4500,
4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)XE
Cisco 7100 series
12.0(6)S
Cisco 12000 series
NetFlow is also supported by these devices Cisco 800, 1700, 1800, 2800, 3800, 6500, 7300, 7600, 10000, CRS-1 and these Catalyst series switches: 45xx, 55xx, 6xxx.
NetFlow export is also supported on other Cisco switches when using a NetFlow Feature Card (NFFC) or NFFC II and the Route Switch Module (RSM), or Route Switch Feature Card (RSFC). However, check whether version 5 is supported, as most switches export version 7 by default.
You can check the below steps to diagnose the issue::
To verify that NetFlow is exported from a device to PI, follow the steps below:
1)   Browse to Administration > Data Sources page. Check the value in column ‘Last Active Time’ for the ‘Device Data Sources’ table. If the table is empty or the value does not represent recent time, then
it is possible that the device is not exporting NetFlow or PI Assurance license is not applied / expired.
2)   Login to PI console ( via SSH) as root user and run the command:
                netstat –an | grep 9991 – Output of this should be like : udp        0      0 :::9991         :::*
                Check the firewall settings on PI server using the command: firewall -L
1)   Check the configuration on an IOS / IOS –XE device. Run the commands
a)   sh running-config | inc destination
1)   This should list the IP address of the PI SERVER ( along with other outputs if any)
b)   sh running-config | inc 9991
1)   This should list at least one entry.
c)   If the above are fine, then verify that the flow monitor, flow exporter and the flow records are correctly configured on the device.
Refer to the URLs below to configure NetFlow export.
http://preview.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/user/guide/setup_monitor.html#wp1056427
Thanks-
Afroz
***Ratings Encourages Contributors ****

Cisco prime infrastructure not detect IP address of clients

hi all,
I have Cisco Prime infrastructure 1.2 and when move to monitor >> clients tab it lists me all the clients in my network but their IP address list estates "not detected" ?
please any advice?
I appreciate your kindly support.

Just an update that while this appears to have worked fairly well (as far as Cisco Management Planes go), there was one small 'gotcha' I've noticed so far:
After the services came back up, the entries for our RADIUS servers did not function. No, not because I didn't update the clients address record on the RADIUS server itself, but because the RADIUS server record(s) within CPI have a field called 'Local Interface IP' that still reflects the previous IP assigned to CPI. A quick edit/save with the new interface fixes up the issue however.
Cheers!

Cisco Prime Infrastructure 2.0 - no traps/info are pushed from devices

Good evening,
I have setup Cisco Prime Infrastructure 2.0 and, though I have added manually my 4 network cores as devices without any problem, I can't get a single trap or a single SNMP information to be pushed into my Cisco Prime Infra.
Here is my SNMP config on my core :
snmp-server user *edited* *edited* v3
snmp-server group *edited* v3 noauth notify *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF0F
snmp-server community *edited* RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps rf
snmp-server enable traps memory
snmp-server enable traps cpu_threshold
snmp-server enable traps eigrp
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps flex-links status
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps ether-oam
snmp-server enable traps aaa_server
snmp-server enable traps flash insertion removal
snmp-server enable traps l2tc threshold sys-threshold
snmp-server enable traps power-ethernet police
snmp-server enable traps rep
snmp-server enable traps vswitch dual-active vsl
snmp-server enable traps udld link-fail-rpt status-change
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps auth-framework sec-violation
snmp-server enable traps dot1x auth-fail-vlan guest-vlan no-auth-fail-vlan no-guest-vlan
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps entity-diag boot-up-fail hm-test-recover hm-thresh-reached scheduled-test-fail
snmp-server enable traps port-security
snmp-server enable traps ethernet evc status create delete
snmp-server enable traps energywise
snmp-server enable traps ipsla
snmp-server enable traps vstack
snmp-server enable traps bfd
snmp-server enable traps bgp
snmp-server enable traps bulkstat collection transfer
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps isis
snmp-server enable traps msdp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps errdisable
snmp-server enable traps ethernet cfm alarm
snmp-server enable traps vlan-membership
snmp-server enable traps mac-notification change move threshold
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *ip-address-edited* version 3 noauth *edited*
Basically all traps are enabled but absolutely nothing is showing up in my Prime Infra except that my 4 devices are "Reachable".
Here is a show snmp on the same device :
sh snmp
Chassis: *S/N Edited*
38554534 SNMP packets input
    0 Bad SNMP version errors
    14 Unknown community name
    0 Illegal operation for community name supplied
    0 Encoding errors
    38453185 Number of requested variables
    0 Number of altered variables
    17790703 Get-request PDUs
    20583581 Get-next PDUs
    0 Set-request PDUs
    0 Input queue packet drops (Maximum queue size 1000)
38490708 SNMP packets output
    0 Too big errors (Maximum packet size 1500)
    0 No such name errors
    0 Bad values errors
    0 General errors
    38371069 Response PDUs
    13 Trap PDUs
SNMP global trap: enabled
SNMP agent enabled
SNMP logging: enabled
    Logging to *edited*, 0/10, 13 sent, 0 dropped.
Can anyone point out what is wrong or missing in my configuration? I can't seem to single it out myself.
Thanks
Jeremy

Hi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

Configure the syslog of ASA 5512-X for display on Cisco Prime Infrastructure 2.1

Hi, I'm working on implementing the Cisco Prime Infrastructure 2.1 and want to display the syslog about ASA5512-X with Software Version 9.2.
What would be the procedure for configuring?
Thanks in advance.

Hi,
Enable "logging host x.x.x.x " command to enable logging
check the below link:
http://www.cisco.com/c/en/us/td/docs/security/asa/asa91/configuration/general/asa_91_general_config/monitor_syslog.html#68764
FYI: Prime Infrastructure support only SEV 0,1,2 syslogs as of now.
Operate > alarm and events > syslogs
Thanks-
Afroz
****Ratings Encourages Contributors *****

Cisco Prime Infrastructure 1.2 synchronizaton with active directory

hi all
I have installed Cisco Prime Infrastructure 1.2 and I want to make a synchronization between the PI and the active directory
note:
I want to make that to be able to search about the users on cisco prime infrastructure using Hostname instead of serching on it using IP or MAC address.
how can I do this task ???
thanks all.
I appreciate your support.

Hi Mohamed,
Integration with AD is not supported in PI
Thanks-
Afroz
[Do rate the useful post]

Cisco nexus 6001 not a supported device on cisco prime infrastructure 2.1?

I have installed Cisco Prime Infrastructure 2.2 and Prime Infrastructure still doesn't seem to support the Nexus 6001 platform? Can someone tell me if Cisco Prime Infrastructure will ever support the Cisco Nexus 6001 platform or is there any plans to support it in any future device packs?

The Nexus 6001 isn't currently supported in PI 2.1. There's no workaround except to wait for a device or product update that adds support. Right now I know the 9000 series is on the 2.2 roadmap but I haven't seen any reference to the 6001 and PI.
Interestingly, Prime LMS does support both the 6001 and 6004. Reference.

Consultations on Cisco Prime Infrastructure 2.2

I recently installed Cisco Prime Infrastructure 2.2 and I have 2 questions regarding configuration:
1. What configurations should run for vulnerability when some event occurs on a switch an alarm is lifted in the Cisco Prime Infrastructure 2.2?
2. Is there any way to put a device into maintenance mode in the web interface of Cisco Prime Infrastructure 2.2, so that can not be spoiled reports regarding equipment availability during the execution of maintenance?

1. If you configure PI as an SNMP and syslog server for your devices and have enabled logging traps etc., PI's alarm browser will show the alarms. If you want them to be sent to you via email, you can do that under the Admin menu for setting up your Mail server and clicking the link to "Configure email notification for individual alarm categories." (see below - open in new tab to zoom). It's not completely customizable but what you see there is the current product capabilities in that regard.
2. No, this is not currently an available feature in PI 2.2.

Software images Cisco Prime Infrastructure

Hi,
I have Cisco Prime infrastructure 2.0 and all it works ok except when i try to get software image from device. I don´t see any device, so i can´t select any device and I get "RSL error".
When i try to access "Operate" > "Configuration Archives", i get the same error.
The machine from where I navigate has last "flash player" version and it has all requeriments.
Which can be the problem?
Thanks.

Hi!
I have experience the same problem under different tools in PI. I did notice it first under “Deploy>Monitoring deployment>Interface Health template>deploy and I get the 2032 error.
I have learn that this occurs when you use a client with no internet connection and you try to start above deployment tools.
What happens is that when you try to open such page in PI web interface, the flash player starts and try to get some files on the PI but the URL it get from the PI application points to a library that do not contains the file (Bug in PI?). The files the flash player looks for is called something like framework_4.5.1.21328.swz and spark_4.5.1.21328.swz and so on. The url from PI looks like https://PI_Server/webacs/applications/SAMDeployTemplate/js/framework_4.5.1.21328.swz but the file is missing.
The flash player have a backup way to get the xxxxxx.swz files it needs. If it can’t find the files in the application, it try to get it from Adobe http://fpdownload.adobe.com . But in my case my client can’t access internet so I get the error 2032.
I have another installation at another site that allows internet access everything works fine. The flash player can load the files it needs and store them locally on the client PC. Then I can take that PC back to the another site with no internet access where I did get the 2032 error and now It works fine because the flash player have the files it needs to handle the PI application.
I have a case open and it has not been solved yet.
Mattias.S

New installation of Cisco prime Infrastructure 1.2

Hi,
We installed Cisco prime infrastructure 1.2 and discovered our entire LAN swtiches and core L3 Switches.
In Cisco Prime, we are getting information related to Device and IOS. But intreface ulitilzation information are not avilable.
we used SNMPv2 RW string and and SSH username for discovery.
How to get the interface ulitization data ?

Under Administration > System Settings, then select Monitoring Settings.
i checked the two options
Auto monitoring
Enable deduplication
But after refresh it is show uncheck, i tried in Google Chrome and Firefox.
Is this cause the issue of not polling interface netflow???

Cisco Prime Infrastructure 1.2 and Aironet 1250 + VSS issues

Similar Messages

Maybe you are looking for