Cisco Prime Infrastructure 1.2 config deployment (no copy run start)

I have deployed some CLI templates I have created to configure multiple local accounts on some switches. However the cli templete only appears to accept conf t commands, it will not accept 'write mem' or 'copy run start' at the end to save the altered running config to startup. this results in running and startup being 'out of sync' in the configuration archives, and runs the risk of a power failure causing the config to revert back to startup. Does anyone know how to ensure the altered running config is saved to startup during the config template deployment?

I don't know if this has been fixed in 2.0 or not. By the looks of the bug it hasn't. However, there is a workaround-
https://tools.cisco.com/bugsearch/search?kw=prime%20infrastructure%20copy%20run%20start&pf=prdNm&sb=anfr&srtBy=byRel&bt=custV
BugID
CSCuf89957
Prime Infrastructure - No option to save running config to startup
Conditions:
Prime Infrastructure 1.2/1.3
Workaround:
Create a Configuration Template that runs either:
"do write mem"
Or for devices which no longer support "write mem", use:
"file prompt quiet
do copy run start
no file prompt quiet"

Similar Messages

CISCO PRIME INFRASTRUCTURE 1.2 CONFIG ISSUE

hello all,
this is my fist time running a cisco prime infrastructure1.2 but it seem not to be working properly as i have errors on it,
I had issues from the very begining and had to write erase the config but the appliance only boots to a blank screen wit a cursor.
can anyone advice on how to restore it back to initial setup
and please whats the effect of the RESET button on the device.
thanks

I don't know if this has been fixed in 2.0 or not. By the looks of the bug it hasn't. However, there is a workaround-
https://tools.cisco.com/bugsearch/search?kw=prime%20infrastructure%20copy%20run%20start&pf=prdNm&sb=anfr&srtBy=byRel&bt=custV
BugID
CSCuf89957
Prime Infrastructure - No option to save running config to startup
Conditions:
Prime Infrastructure 1.2/1.3
Workaround:
Create a Configuration Template that runs either:
"do write mem"
Or for devices which no longer support "write mem", use:
"file prompt quiet
do copy run start
no file prompt quiet"

Ask the Expert: Cisco Prime Infrastructure - Implementation and Deployment

Welcome to the Cisco Support Community Ask the Expert conversation.
This Ask The expert Session will cover questions spanning Cisco Prime Infrastructure on Implementation and Deployment on Wired and Wireless. This will be more specific to Customer’s and Partners questions product covering PI on configuration, Features and Menu, Network Monitoring, Maps, Implementation, High Availability and Maintenance and t/s parts.
Monday, February 2nd, 2015 to Friday, February 13th, 2015
Dhiresh Yadav is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco Prime Infrastructure and Cisco Wireless products. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS) and CCIE (DC) certifications.
Afroz Ahmad is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS),CCIE (DC), and SCJP (Sun Certified Java Professional )
Vinod Kumar Arya is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 8 years of industry experience working with large enterprise and service provider networks. He also holds VCP 5 and RHCE certifications.
** Remember to use the rating system to let the experts know you have received an adequate response.**
Because of the volume expected during this event, the experts might not be able to answer every question. Remember that you can continue the conversation in the Network Infrastructure community, > Network Management, shortly after the event. This event lasts through February 13th 2015. Visit this forum often to view responses to your questions and those of other Cisco Support Community members.

Hello Wilson,
Thanks for joining us.
1841 should just work fine for net flow . Hope you have a valid "PI Assurance license" installed on the server.
"PI Assurance license" is required for "net-flow" feature
Devices supporting Netflow in PI ::
1400, 1600, 1700 & 1800
2500, 2600 & 2800
3600, 3700, 3750 & 3800
4500 & 4700
AS5300 & 5800
7200, 7300, 7400 & 7500
Catalyst 4500 ASCI
Catalyst 5000, 6500, & 7600 ASCI
ESR 10000 ASCI
GSR 12000 ASCI
Cisco IOS Software Release Version
Supported Cisco Hardware Platforms
11.1CA, 11.1CC
Cisco 7200 and 7500 series, RSP 7200 series
12.0
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series
12.0T, 12.0S
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8600 series
12.0(3)T, 12.0(3)S
Cisco 1720, 2600, 3600, 4500, 4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)T
Cisco 1400, 1600, 1720, 2500, 2600, 3600, 4500,
4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)XE
Cisco 7100 series
12.0(6)S
Cisco 12000 series
NetFlow is also supported by these devices Cisco 800, 1700, 1800, 2800, 3800, 6500, 7300, 7600, 10000, CRS-1 and these Catalyst series switches: 45xx, 55xx, 6xxx.
NetFlow export is also supported on other Cisco switches when using a NetFlow Feature Card (NFFC) or NFFC II and the Route Switch Module (RSM), or Route Switch Feature Card (RSFC). However, check whether version 5 is supported, as most switches export version 7 by default.
You can check the below steps to diagnose the issue::
To verify that NetFlow is exported from a device to PI, follow the steps below:
1)   Browse to Administration > Data Sources page. Check the value in column ‘Last Active Time’ for the ‘Device Data Sources’ table. If the table is empty or the value does not represent recent time, then
it is possible that the device is not exporting NetFlow or PI Assurance license is not applied / expired.
2)   Login to PI console ( via SSH) as root user and run the command:
                netstat –an | grep 9991 – Output of this should be like : udp        0      0 :::9991         :::*
                Check the firewall settings on PI server using the command: firewall -L
1)   Check the configuration on an IOS / IOS –XE device. Run the commands
a)   sh running-config | inc destination
1)   This should list the IP address of the PI SERVER ( along with other outputs if any)
b)   sh running-config | inc 9991
1)   This should list at least one entry.
c)   If the above are fine, then verify that the flow monitor, flow exporter and the flow records are correctly configured on the device.
Refer to the URLs below to configure NetFlow export.
http://preview.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/user/guide/setup_monitor.html#wp1056427
Thanks-
Afroz
***Ratings Encourages Contributors ****

Email notification for config deployment jobs in Cisco Prime Infrastructure 1.2 ??

We're upgrading from LMS 3.2 to Cisco Prime Infrastructure ...
In LMS 3.2 we're using netconfig all the time to configure various jobs related to port security
In installing Cisco Prime Infrastructure and working through it's use of templates, I'm having some difficulty finding out how to send out a notification once a configuration job has completed. It's so simple in LMS 3.2 since it's part of the job creation screens.
Any assistance would be greatly appreciated.

HI, Raymond
Just wondering if this problem is resolved?
Thanks!

Cisco Prime Infrastructure deployment through Cisco 3945 ISR

Dears,
I have Cisco 3945 ISR include module for the Cisco prime infrastructure.
I need to deploy the prime but when I connected monitor on the module I saw that it is looking for DHCP only.
Please can anyone support me with procedure to install the prime?
Should I install the ESXi on this module by make it boot from external device (USB, or CD drive)?
Your support is highly appreciated,
Regards,

Duplicate post.
Go HERE.

Deploying Cisco Prime Infrastructure 1.2

For the deployment of Cisco Prime Infrastructure 1.2 do I need to have 1 or 2 appliances or vms. From what I can read version 1.2 is supposed to combine Cisco Prime LMS and NCS into one pane of glass for management so I would assume that I would only need one appliance or VM.
Thanks.
Tyler

Not completely just yet. PI 1.2 does incorporate some LMS 4.2 functionality but falls short of a complete replacement. So for now if you want all the bells and whistles of LMS 4.2, you still need to build a separate instance of LMS. At least it is included with the PI 1.2 license.
PI 2.0 is supposed to bring more feature parity - we'll see though....

Cisco prime infrastructure 2.2

Hello Team,
I did like to know how i can create a baseline template using Cisco prime infrastructure 2.2 in order to compare configuration of devices.
Also I would like to inquire how I can generate a CLI template and view the CLI template before applying/deploying it to a particular device or devices.
Best Regards,
Tioluwani

Having just started with Prime not that long ago, I'm afraid I can't help with your first question. However, for your second question:
Go to Configuration > Templates > Features and Technologies
Along the left menu, expand CLI Templates and click on CLI
This will bring up a new, blank CLI template to the right of the menu
Just fill out the info at the top section, and input your CLI/Velocity code in the bottom section
Once you have the code like you want it, click the "Save as New Template" button at the bottom
A window will pop-up asking where you want to save it within the "My Templates" folder
Once you've selected a location, click the Save button
Your window will automatically refresh to show the newly created custom CLI template - you will now have the option to edit your template as needed, or deploy it as-is to PI devices.
To deploy the template, select the Deploy button along the bottom
A new window will pop up that allows you to prepare and schedule the template. Select the device or devices you wish to deploy to. The devices you have available to deploy to will be based on the Validation Criteria you entered when creating the template.
If you opted to use the awesome variables available to CLI templates, you can either enter those for all selected devices in the Value Assignment section, or you can fill out the variables on a per-device basis. You will skip this section if you did not define any variables. If you did use variables, you must click the Apply button at the bottom of this section after you fill in the variables, or you will receive the following error:Mandatory fields are not entered for some devices or you have not saved your changes. To save the changes, click on Apply.
In the Schedule section, you can select when the template is deployed - "Now" is the default.
Finally, the Job Option section allows you to select how Prime handles a deployment failure, whether you want Prime to save the config to startup after the deployment, and whether you want to initiate a config archive after the deployment.

Cisco Prime Infrastructure 1.2 is not working https & ncs

Hi, I have just deploy Cisco Prime Infrastructure 1.2 in a virtual appliance (Vmware Esxi 5.1). Console is ok & setup is also completed. but there is no NCS application. only app is shwoing: NCSPNP
Cannot access from https also.
Please suggest how to Starting Prime Infrastructure Serve

From what you describe, it sounds like you have installed the Plug and Play (PNP) ova image. You need to install the Prime Infrastructure image.
See the screenshot below for details (click to enlarge):

What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP's?

What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP’s?

• PI provides visibility for autonomous clients within the same list view as lightweight and wired clients (client list page).
• Rogue AP detection for autonomous AP's is not supported (it's supported in CUWN).
• Alarms/events for client authentication issues (e.g. authentication failure) are displayed in PI.
• Config management for autonomous AP's is via CLI template. Config comparison and archiving functionality in PI leverages these same features that were brought in from LMS, so need to defer to others in terms of whether this is a cross-platform feature in PI or is only supported on a subset of platforms. Config comparison/archive is supported in CUWN.PI supports both infrastructure (e.g. AP Tx Power and Channel, busiest AP, AP utilization, etc.) and client (e.g. client count, client sessions, etc.) reports, and there are extensive reports for CUWN

Cisco Prime Infrastructure 2.0 and Cisco ASA

Hello,
We've recently installed trial version of Cisco Prime Infrastructure 2.0 Express. We hoped that it already supports Cisco ASA 55xx series (especially 5505, we have pretty amount of them). But we had some problems with PI and asa durind the exploitation process.
First, I've added ASA to PI, and Inventory Collection Status is Completed, but I can't see CPU and RAM utilization graphs. Inventory.logs are non-informative.
Also, config backup is success, but when I try to watch the backuped configuration at Configuration Archive PI says "Failed to fetch raw configuration". And so on.
ASA version is 5505, image is 9.1(2).
So, I have a question: is it possible to manage ASAs with PI 2.0?
UPD: I've just tried to upgrade asa to 9.1(4), and behavior of the equipment is quite the same. Seems we shall wait for 9.2 to be released.

Have you downloaded and applied the latest Device Pack updates?
PI enhanced ASA support after the initial 2.0 release and the Device Packs incorporate that change.
The README file for Device Packs explains how to install them. (A bug currently does not allow the direct download in PI so you need to follow the method for installation from local storage after you manually download. Here is a link to the download location.

Cisco Prime Infrastructure 2.0 - no traps/info are pushed from devices

Good evening,
I have setup Cisco Prime Infrastructure 2.0 and, though I have added manually my 4 network cores as devices without any problem, I can't get a single trap or a single SNMP information to be pushed into my Cisco Prime Infra.
Here is my SNMP config on my core :
snmp-server user *edited* *edited* v3
snmp-server group *edited* v3 noauth notify *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF0F
snmp-server community *edited* RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps rf
snmp-server enable traps memory
snmp-server enable traps cpu_threshold
snmp-server enable traps eigrp
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps flex-links status
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps ether-oam
snmp-server enable traps aaa_server
snmp-server enable traps flash insertion removal
snmp-server enable traps l2tc threshold sys-threshold
snmp-server enable traps power-ethernet police
snmp-server enable traps rep
snmp-server enable traps vswitch dual-active vsl
snmp-server enable traps udld link-fail-rpt status-change
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps auth-framework sec-violation
snmp-server enable traps dot1x auth-fail-vlan guest-vlan no-auth-fail-vlan no-guest-vlan
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps entity-diag boot-up-fail hm-test-recover hm-thresh-reached scheduled-test-fail
snmp-server enable traps port-security
snmp-server enable traps ethernet evc status create delete
snmp-server enable traps energywise
snmp-server enable traps ipsla
snmp-server enable traps vstack
snmp-server enable traps bfd
snmp-server enable traps bgp
snmp-server enable traps bulkstat collection transfer
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps isis
snmp-server enable traps msdp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps errdisable
snmp-server enable traps ethernet cfm alarm
snmp-server enable traps vlan-membership
snmp-server enable traps mac-notification change move threshold
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *ip-address-edited* version 3 noauth *edited*
Basically all traps are enabled but absolutely nothing is showing up in my Prime Infra except that my 4 devices are "Reachable".
Here is a show snmp on the same device :
sh snmp
Chassis: *S/N Edited*
38554534 SNMP packets input
    0 Bad SNMP version errors
    14 Unknown community name
    0 Illegal operation for community name supplied
    0 Encoding errors
    38453185 Number of requested variables
    0 Number of altered variables
    17790703 Get-request PDUs
    20583581 Get-next PDUs
    0 Set-request PDUs
    0 Input queue packet drops (Maximum queue size 1000)
38490708 SNMP packets output
    0 Too big errors (Maximum packet size 1500)
    0 No such name errors
    0 Bad values errors
    0 General errors
    38371069 Response PDUs
    13 Trap PDUs
SNMP global trap: enabled
SNMP agent enabled
SNMP logging: enabled
    Logging to *edited*, 0/10, 13 sent, 0 dropped.
Can anyone point out what is wrong or missing in my configuration? I can't seem to single it out myself.
Thanks
Jeremy

Hi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

Cisco Prime Infrastructure 1.3 Web Log Invalid user password

Hi,
I recently installed Cisco Prime Infrastructure 1.3 per the set up guide. I was able to login into the webinterface.
Then I insert the radius server and reload ncs. Since then I'm not able to login to the web interface. I get the following error message "Invalid Username or Password. Please try again". Even when I set the ncs root user with a new password. One issue could be that i forgot the enable fallback to local.
Is there a way to change the radius config back via cli?
Thanks a lot
Hansruedi

Hi Hansruedi,
Thanks you for your help and your time.
I followed your recomandation until the fourth step.
But after this step, I lost the web page connection.
I check nsc status but all is running :
NMS still stopped. NMS must be running to have an access by web page ?
I restart Prime (by reload command) but nothing changed.
Thanks

Cisco Prime Infrastructure 1.2 and Aironet 1250 + VSS issues

Hi,
I am new to the NCS implementations and configurations. I have one very specific case with Cisco Prime Infrastructure 1.2 and autonomnous APs and several issues with Cisco VSS on 6500 switches.
So here is the version from Prime:
NCS/admin# show version
Cisco Application Deployment Engine OS Release: 2.0
ADE-OS Build Version: 2.0.1.038
ADE-OS System Architecture: x86_64
Copyright (c) 2005-2010 by Cisco Systems, Inc.
All rights reserved.
Hostname: NCS
Version information of installed applications
Cisco Prime Network Control System
Version : 1.2.1.012
IOS version on our APs (which are autonomnous) is:
AP-N-1>show ver
Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(25d)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 11-Aug-11 03:23 by prod_rel_team
Well the issue what we have now is that access point has been added but its not recognized by the NCS prime. I have tried all three versions of SNMP but I get the same result. The SNMP configuration is valid since I use the same for my switching infrastructure. When I enter "debug snmp packets" and "terminal monitor" I can see the SNMP communication between Prime and Aironet 1250 which is standalone.
When I switch to Lifecycle theme and go to Operate > Device Monitor Center I see all devices I have added. The Aironet 1250 is reachable but under collection status I get Managed with Warnings. When I hover over with my mouse I get "None available".
I have successfully added my switching infrastructure in total, which is operating perfectly for Catalyst 2960/3650/3750/4500 series but for 6500 under VSS I have some warnings. The device is recognized by the system which is excellent and all is operational. I get the following errors under Collection Status:
feature_sensor
SNMP request timed out
feature_powerSupplyFanStatus-6k
SNMP request timed out
IdentityCapability
The device is unreachable.
feature_flashdevice
SNMP request timed out
sam_ipsla_feature
The device is unreachable.
What can be done to resolve these issues ? I have attached a screenshot of this particular issue. The affected access point is 172.16.165.241.
Predrag Petrovic

Hi rajeeshp,
Currently I am not allowed to upgrade it because of internal procedures involved in upgrading a specific piece of software (obtaining permissions from various departments). Is it free to upgrade from 1.2 to 1.3 or there is a specific charge for that.
Predrag Petrovic

Cisco Prime Infrastructure 1.3 - SNMPv3 can´t get CPU, memory info.

Hi,
I have a Cisco Prime Infrastructure 1.3 deployment with Catalyst 2960S switches. Switches are running IOS 15.0(2) SE2. All switches have SNMPv2 configured, and all appears to be fine. I'm migrating one switch to SNMPv3, and PI have reachability to the switch, but PI doesn´t receive traps from the switch, and neither poll CPU and memory information (all displays 0.00%).
Somebody have a sample configuration of SNMPv3 with Cisco Prime (Infrastructure or LMS)? I cannot find a Cisco official (or unofficial) document related to this version, usually all mention SNMPv2.
Thank you.
Eduardo

Hi Eduardo:
SNMPv3 is indeed supported for general administration. There's a bug with SWIM using SNMPv3 (CSCud92758), but you should be fine for just monitoring. Have you deleted the switch, waited until Prime Infrastructure told you it was gone, then readded it as SNMPv3 natively? Bug CSCug78869 keeps things from working well when changing SNMP versions.
If you don't have the new Update-1 patch for Prime Infrastructure 1.3.0.20 installed (filename PI_1.3.0.20_Update_1-12.tar.gz) installed, I'd suggest you get it. While it's not going to specifically address this issue, there are a lot of really good fixes in it.
Release Notes for Update 1 for Cisco Prime Infrastructure 1.3.0.20

Monitoring ASA in Cisco Prime infrastructure 2.2

Hi everybody. I have some issue with cisco Prime Infrastructure 2.2. We use this product in our network for monitoring network devices and I need to monitor also our ASA 5550 device with soft 8.4. I added ASA to Cisco PI but see only basic component like my device can reachable via and read via snmp. But cannot see CPU, RAM, Device ENV like Temperature, l2l vpn connection, Interfaces status and Utilization that interfaces, cannot see sub interface that placed on ASA like that g0/0.20. I need fully monitor ASA and See logs and trap for my device:
CPU RAM ENV (Temperature), Interface and sub interface status, L2L VPN Status.
1 Cisco Prime infrastructure can full support ASA for monitoring and logging.. IF YES how can i configure that features in Cisco PI 2.2 for ASA
2 IF not which product Can full support that features for full monitoring and logging ASA devices
I have a little deadline for finishing
thanks everybody before

I've not success monitoring ASA interface utilization either. I'm using PI 2.2 with device update #1. The ASA is a 5585-X with 9.2(3) software.
I have deployed the PI monitoring template to the ASA and do see its overall status and PI has enumerated the interfaces in the device page.
I even looked at a packet capture and see PI querying the values of the interface counters and those values being sent back to PI - yet I cannot select any ASA interface when drilling down under Performance Detail monitoring.
When I get some free time I will open a TAC case on it, meanwhile I am getting all the info I need from the upstream and downstream switches.

Cisco Prime Infrastructure 1.2 config deployment (no copy run start)

Similar Messages

Maybe you are looking for