Cisco Prime Infrastructure 1.2 with SNMPv3

Dears,
I am trying to add a router on Cisco Prime Infrastructure 1.2 using snmpv3 (authpriv, sha & aes256). When i go to device work center and add a device, i cannot find the AES-256 in the privacy options. Only None, DES, and AES-128 are available.
Is there any workarround?
Please advise.
Moustafa

PI only supports SNMP privacy up through AES-128 at this time. Reference the guide section on adding an new SNMP credential entry.
Additionally there is a bug with SNMP v3 support in PI 1.2. It should be resolved in PI 1.3.

Similar Messages

Can i install Cisco prime infrastructure 1.3 with 1.1 license.

Can i install Cisco prime infrastructure 1.3 with 1.1 license.To be more precise it will be fresh installation
but the licenses I have is of 1.1.As per my overview from Cisco prime Infrastructure 1.2 NCS and NCS(WAN)
has been bundled into one service.But both were seperate entities in Cisco Prime Infrastructure 1.1.

It doesn't matter if you want to make a new installation or an upgrade. The questions is the license.
The base license is necessary for network management nodes (devices). But to get updates for your system you need the additional to your Base License the Lifecycle License (which can be ordered for 12, 24 or 36 months).
The Lifycycle License is also based on the number of managed devices. In your case 50 devices. So you have that License - congratulations!
Otherwise order the Lifecycle License for 50 devices (L-N-PI12-50-M). This generates CON-PSUU-PI12LF50 for 12 months, list price 414,81$. Then Upgrade from 1.1 to 1.2, patch the system and upgrade to 1.3.
Have fun,
Chris

Cisco Prime Infrastructure 1.2 with Cisco Prime Network Control System Hardware Appliance

Hi Team,
I have following BOM
Cisco Prime Infrastructure
R-PI-1.2-K9
Cisco Prime Infrastructure 1.2
1
R-PI-1.1-500-K9
Prime Infrastructure 1.2 Software - 500 Device Base Lic
1
L-PILMS42-500
Prime Infrastructure LMS 4.2 - 500 Device Base Lic
1
L-PINCS12-500
Prime Infrastructure NCS 1.2 - 500 Device Base Lic
1
PRIME-NCS-APL-K9
Cisco Prime Network Control System Hardware Appliance
1
PI-APL-IMAGE-1.2
Cisco Prime Infrastructure 1.2 Appliance Software
1
Pls let me know if we have both NCS and LMS preinstalled with Cisco Prime Infrastructure 1.2 Appliance Software orwe need seperate appliance or server for LMS 4.2.
Regards

Hi Scott,
Thanks for the response but I got to know that LMS and NCS are combined in single ISO image from PI 1.2 and can be installed on the same physical NCS appliance.
Can you pls check this.
Regards

Create a user on Cisco Prime Infrastructure 1.3 with a script ?

Hello, we have a visiting software that does not support Cisco Prime configuration.
I was thinking that maybe I can write a script or something like that to create a Wireless User Account when a visitor signs in at our reception.
Grabbing the login information from the database and then creating the account on the Cisco Prime.
The script will run on another computer so a VBScript or something like that would be best.
Is this possible ?
I have googled for hours now and have found the API site but cannot make sense of it.
I know how to get the information but inserting it in the Cisco Prime is what I am having trouble with.
Could anyone here help me with an example or steer me in the right direction to learn how to do this ?

Hi Hansruedi,
Thanks you for your help and your time.
I followed your recomandation until the fourth step.
But after this step, I lost the web page connection.
I check nsc status but all is running :
NMS still stopped. NMS must be running to have an access by web page ?
I restart Prime (by reload command) but nothing changed.
Thanks

Cisco Prime Infrastructure 2.2 clients and users IPs not detected

Hi all,
I have cisco PI2.2 and discovered all the network and i notified that there are some clients' IPs (Servers or PCs or Laptops or ....) not detected.
please advice what may be the issue ?

Hi,
does anyone happen to know if that problem is fixed? My currently setup looks like this:
1. Cisco Prime Infrastructure 2.1 with updated device pack.
2. Assurance license
3. ASA5510 which has enabled netflow. Netflow is being sent to Cisco Prime 2.1
I do receive netflow raw data within Cisco Prime 2.1 but any graphical display of netflow data is not working. Does anybody has an idea where the problem is? Could it be that the graphical data is only displayed when sending netflow 1, netflow 5 or netflow 7?
regards
Maurus

Cisco Prime Infrastructure 2.0 and ASA 55xx platform problem

Hello,
We recently upgraded to Prime Infrastructure 2.0 with the hope being able to manage our ASA's from PRIME (and complete an LMS migration).
When I attempt to add ASA's to prime i get the following collection errors:
Unable to collect processor and RAM information.          Processor and RAM information.          Unexpected error. See the log file inventory.log for details.
In the logfile I get the following XML parsing error on the MIB:
<palError>
<deviceId>6284310032</deviceId>
<code>VALIDATION_ERROR</code>
<message>Failed to validate output XML: cvc-maxInclusive-valid: Value '3484331296' is not facet-valid with respect to maxInclusive '2147483647' for type 'int'.</message>
<result>
    <result xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="/CISCO-MEMORY-POOL-MIB/xmp-im-file-system-module.xsd">
      <xmp-im-file-system-module>
        <MemoryPoolStatistics>
          <memoryPoolIndex>1</memoryPoolIndex>
          <free>4294967295</free>
          <largestFree>4294967295</largestFree>
          <used>3484331296</used>
        </MemoryPoolStatistics>
To me it seems that the ASA returns a value that is bigger then int32 and thus causes an overflow? Any clues? Workarounds to add an ASA to Prime without checking these MIB'S?
Regards,
Marcel

Hi,
does anyone happen to know if that problem is fixed? My currently setup looks like this:
1. Cisco Prime Infrastructure 2.1 with updated device pack.
2. Assurance license
3. ASA5510 which has enabled netflow. Netflow is being sent to Cisco Prime 2.1
I do receive netflow raw data within Cisco Prime 2.1 but any graphical display of netflow data is not working. Does anybody has an idea where the problem is? Could it be that the graphical data is only displayed when sending netflow 1, netflow 5 or netflow 7?
regards
Maurus

Cisco Prime Infrastructure 1.3 - SNMPv3 can´t get CPU, memory info.

Hi,
I have a Cisco Prime Infrastructure 1.3 deployment with Catalyst 2960S switches. Switches are running IOS 15.0(2) SE2. All switches have SNMPv2 configured, and all appears to be fine. I'm migrating one switch to SNMPv3, and PI have reachability to the switch, but PI doesn´t receive traps from the switch, and neither poll CPU and memory information (all displays 0.00%).
Somebody have a sample configuration of SNMPv3 with Cisco Prime (Infrastructure or LMS)? I cannot find a Cisco official (or unofficial) document related to this version, usually all mention SNMPv2.
Thank you.
Eduardo

Hi Eduardo:
SNMPv3 is indeed supported for general administration. There's a bug with SWIM using SNMPv3 (CSCud92758), but you should be fine for just monitoring. Have you deleted the switch, waited until Prime Infrastructure told you it was gone, then readded it as SNMPv3 natively? Bug CSCug78869 keeps things from working well when changing SNMP versions.
If you don't have the new Update-1 patch for Prime Infrastructure 1.3.0.20 installed (filename PI_1.3.0.20_Update_1-12.tar.gz) installed, I'd suggest you get it. While it's not going to specifically address this issue, there are a lot of really good fixes in it.
Release Notes for Update 1 for Cisco Prime Infrastructure 1.3.0.20

UPS monitoring support with Cisco Prime Infrastructure 1.2

Dear Members,
Good day,
I am having a project implemented wherein i have the UPS power redudancy solution for our network devices.
Now can anyone gide that is it possible for below :-
UPS units installed with SNMP cards be monitored via Cisco Prime Infrastructure 1.2 as our monitoring & management solution is Cisco Prime Infrastructure 1.2 ?
if yes
Can you guide if following action would be possible to export the below logs from UPS unit to our Cisco Prime Infrastructure 1.2
   a) UPS fault status information
   b) UPS operational status(input power available Y/N)
   c) Battery fault status
   d) Battery charging current
   e) Battery charge level
   f) Output current
Conclusion is we need to confirm that would it be posible to achieve remote monitoring of these UPS units via our CPI 1.2
Thanks in Advance for your support & replies to this query.
Regards,
Muzammil N.

Prime Infrastructure 1.2 can manage non-Cisco devices in a limited fashion via SNMP query and trap processing. It cannot import logs and does not have a generic syslog server,
So if your devices have snmp read only support and can generate SNMP traps for the above you can add them to PI. Follow the manual add device procedure here.

Cisco Prime Infrastructure 1.2 synchronizaton with active directory

hi all
I have installed Cisco Prime Infrastructure 1.2 and I want to make a synchronization between the PI and the active directory
note:
I want to make that to be able to search about the users on cisco prime infrastructure using Hostname instead of serching on it using IP or MAC address.
how can I do this task ???
thanks all.
I appreciate your support.

Hi Mohamed,
Integration with AD is not supported in PI
Thanks-
Afroz
[Do rate the useful post]

Problem with implementing license in Cisco Prime Infrastructure 2.2

Goodday,
For Cisco Prime Infrastructure 2.2 I downloaded an license from the license portal.
This concerns a eval/demo license, for an demo of Cisco Prime Infrastructure 2.2.
When selecting the the type of license you get a few options, from which I selected the basic, advanced and lifecycle evaluation licenses. This is the type of license that is required for our demo.
After completing the wizard I can download en implement the license.
Until this point everything goes as it supposed to be.
When i go to the Prime Infrastructure 2.2 appliance (running on VMWare ESXi 5.5.0).
When I go to the license section in Cisco Prime Infrastructure I can implement the license, however if I implement the .lic file I get the error “Unknown feature (PI_VM)”.
I have done implementing license files before, but this is the first time i encounterd this problem.
Who can help me with this error?
Regards,
Dennie Verhoeven

Hi Dennie,
PI2X-BASE-LF-AS-US-VM-N-EVAL-90   >> I think you have used this product name while generating the license
Either you try generating a new license or contact cisco license team to generate a new license
with the information like below ::
Product Name                : R-PI2X-K9
    Product Description         : R-PI2X-K9:R-PI2X-K9 : Cisco Prime Infrastructure 2.x
    Product Qty                 : 1
    UDI                        : PID: PRIME-NCS-VAPL SN: ANY:ANY
Serial no : with ANY:ANY will work as starting from PI 2.2 , there is no node locking with license.
Thanks-
Afroz
****Ratings Encourages Contributors ****

Trouble With Cisco Prime Infrastructure 1.3

Hi,
I have installed the Evaluation Version Cisco Prime Infrastructure 1.3.
There are a few problems that i am facing;
I am trying to push a simple configuration to WLC using Prime Infrastructure. But it is failing as PI doesnot have RW SNMP access.
My question is that can I use PI to push configs without using SNMP. Like do it using ftp or something.
Also do the Wired Devices also need SNMP RW access on PI's part.
2. I tried running discovery for WLC and it worked fine where all the controllers were discovered. But when I try to discover a Switch, the reachability tab says Reachable but in Collection Status tab it shows Unmanaged. When I click on the Unmanaged tab it says " Pre-collection check failed because: ". I have configured the SNMP correctly.
3. I have the CAD files for all the maps in our environment but when I try to upload it to Prime it converts it into GIF, so the maps are uploaded as plain image with no knowledge of walls and obstacles.
So we would have to add the walls and obstacles by ourselves. Is there any way it can automatically pick up on the walls and obstacles and thus provide a better way for predicting RF profiles.
All your help is greatly appreciated.

TAC Case! Sounds like a bug to me...
Sent from Cisco Technical Support iPad App

User Name and Password for Cisco Prime Infrastructure 2.1

Hi all:
I am stuck at the login page of Cisco Prime Infrastructure 2.1.
I have tried using the user name root and its password (when log in with root at Vsphere Client) and also the login user name "before" get into the appliance infrastructure, all cannot work.
Anybody knows what is the default username or password or any way to set the username and password for this Cisco Prime Infrastructure 2.1 website?
Thanks!
tangsuan

Hi Tangsuan,
Following is the documented procedure for password recovery..
In order to modify the GUI root user password, you will need to login to the NCS CLI
as an admin user, and enter the command
"ncs password root password <new password>" (without the quotes)
This should set the web interface root user password :
http://www.cisco.com/en/US/docs/wireless/ncs/1.1/configuration/guide/manag.html#wp1268889
If you have lost your CLI password , try the default logging that is ,
CLI user is admin and not root, so please try logging in as admin with
the password that was set during setup. If that does not work , you need
the install disk that came with the appliance to recover that password.
Follow these steps:
Recovering a Lost Admin Password
If you lose or forget the admin password for NCS appliance, follow these steps.
Step 1 Reboot the NCS appliance with the ISO DVD inserted. The Cisco Prime Network Control
System Welcome screen appears:
ISOLINUX 3.11 2005-09-02 Copyright (C) 1994-2005 H. Peter Anvin
             Welcome to Cisco Prime Network Control System
To boot from hard disk, press <Enter>.
Available boot options:
   [1] Network Control System Installation (Keyboard/Monitor)
   [2] Network Control System Installation (Serial Console)
   [3] Recover administrator password. (Keyboard/Monitor)
   [4] Recover administrator password. (Serial Console)
<Enter> Boot existing OS from Hard Disk.
Enter boot option and press <return>.
boot:
Step 2 Select the desired recovery option, 3 or 4, depending on how you
are connected to the appliance and then follow the prompts.
Thanks-
Afroz
***Ratings Encourages Contributors ****

When is Cisco Prime Infrastructure 2.0 released, and what does 2.0 offer?

We are running Prime Infrastructure 1.3 primarily for wireless management at this point. We have enough licenses to add all our switches, routers, and firewalls, but we're hesitant to do so until 2.0 comes out. While there are some features for backing up and configuring switches and routers, 1.3 still seems pretty limited in regards to non-wireless features. For example, nearly every report in 1.3 is for wireless controllers or AP's, there are no reports I've found relevent for switches and routers. I've read a lot of blogs, cisco posts, and white papers talking about how Cisco Prime Infrastrucure 2.0 will finally consolidate Prime into a truly all-in-one network management suite that can manage the entire Cisco environment. Does anyone know when it's officially being released? Does anyone have an tech sheets on what's new in 2.0, or what its capabilities are? I want to better understand what 2.0 has to offer, when it's coming out, how to upgrade, so I can start planning for the upgrade and eventually importing all our network devices to Cisco Prime for centralized management. Any useful information or links would be appreciated.
Thanks,
Christian

PI 2.0 is in Beta mode for testing in closed group already. However it may still take some time to get released on CCO for FCS.
I think it is expected to be released between aug-sep. BU has also started working on CPI 2.1, which you can see test uploads on CCO.
For what does it have for customers?
> As Cisco have a vision of one network Management software for both wired and wireless infrastructure, which started getting real partially with Cisco PI.
As WCS got evolved to NCS and eventually to Cisco Prime Infrastructure, but it doesnt yet have full Management capability for wired infra., which is there with LMS.
With CPI 2.x Cisco plans to blend entire LMS and WCS features together.
-Thanks

Can't import images in cisco prime infrastructure 1.2

- Any job , trying to import images, in my cisco prime infrastructure fails with :
Jan 14 13:14:53 cisco-prime 01/14/13 13:15:18.040 ERROR [service] [pool-4-thread-19] IFM_SWIM_EXCEPTION: [com.cisco.ifm.swim.service.exception.IfmSwimParserException: Cannot populate software image info object from the image.]
How I can I solve this one ?
Tx,
M.

I seem to have the same problem, strangely enough importing a universal image for 2960s worked fine, but I get thos error when trying to import a 3750x image

Cisco prime infrastructure not detect IP address of clients

hi all,
I have Cisco Prime infrastructure 1.2 and when move to monitor >> clients tab it lists me all the clients in my network but their IP address list estates "not detected" ?
please any advice?
I appreciate your kindly support.

Just an update that while this appears to have worked fairly well (as far as Cisco Management Planes go), there was one small 'gotcha' I've noticed so far:
After the services came back up, the entries for our RADIUS servers did not function. No, not because I didn't update the clients address record on the RADIUS server itself, but because the RADIUS server record(s) within CPI have a field called 'Local Interface IP' that still reflects the previous IP assigned to CPI. A quick edit/save with the new interface fixes up the issue however.
Cheers!

Cisco Prime Infrastructure 1.2 with SNMPv3

Similar Messages

Maybe you are looking for