Cisco Prime Infrastructure 1.3 Tacacs+ authorization problem
Hello,
We are having trouble setting our new installation of Cisco PI 1.3 to work with Tacacs+ configured on ACS 4.2.
We have followed procedure explained in Cisco PI 1.3 configuration guide and in Tacacs+ logs we can see that we have successful authentification but authorization is unsuccessful:
21/05/2013,16:36:44,Authen OK,pradoicic,admins,192.168.187.109,,192.168.187.109,wifi-prime-p-vm01,AP,ACS1AERO,1,,,192.168.187.109,No Filters activated.,,,No,
21/05/2013,16:36:44,Author failed,pradoicic,admins,192.168.187.109,,Service denied,protocol=HTTP service=NCS,NCS HTTP,192.168.187.109,wifi-prime-p-vm01,AP
We have added user group into ACS as is explained in configuration gude and we have also tried to add virtual domain at the beggining or at the and of the list but that didn't solve our problem.
Is there anything that we can do in order to make Cisco PI to authentificate users using Tacacs+?
Any help in finding solution for this problem will be very appreciated.
Regards,
Jelena
Hi,
On the Cisco PI side we have:
1. Added Tacacs+ server under Administration > AAA > TACACS+
We have entered all required parameters
2. Enabled AAA Tacacs+ mode under Administration > AAA > AAA Mode and we have choosed on auth failure or no server response oprion.
On the ACS side:
1. Under Network Configuration > New Entry we have added Cisco PI
2. Under Interface Configuration >TACACS+ (Cisco IOS) > New Services >
we have added Prime and HTTP (we have checked box infront of these service).
3. Under Group Setup > Edit Settings > prime HTTP service we have added custom attributes that we have copied from Cisco PI Admin group. We have also exported virtual domain information from Prime and have imported them on the beggining of the custom attributes and we have also tried to place that virtual domain information on the end but we have the same behavior.
For some reason ACS doesn't know how to return authorization information.
Regards,
Jelena
Similar Messages
-
Cisco Prime Infrastructure 2.1 Image Distribution Problem
Hey Guys,
Trying to upgrade a switch using Prime. The switch Sync's fine with Prime, SNMP and Telnet/SSH credentials seem to work. However when trying to push an Image I get the following errors in the job description:
Distributing image c3560-ipbasek9-tar.150-2.SE6.tar using protocol TFTP FAILURE
Distributing image c3560-ipbasek9-tar.150-2.SE6.tar using protocol SCP FAILURE
How can I find out more details as to what exactly the failure is?
Thanks!Interesting note:
I found that when using the "Software Deployment" instead of the "Image" tab under a device in the "Device Work Center" to do upgrades, I encounter this problem less often.
However the problem still does occur at times and an additional problem I'm facing is that at times the upgrade jobs succeed fine, but the devices never get rebooted (in spite of having the snmp-server system-shutdown string in the config). In that case the job will never finish and shows as 'running' 10 days later. The Job also can't be cancelled or aborted successfully. -
Problem with implementing license in Cisco Prime Infrastructure 2.2
Goodday,
For Cisco Prime Infrastructure 2.2 I downloaded an license from the license portal.
This concerns a eval/demo license, for an demo of Cisco Prime Infrastructure 2.2.
When selecting the the type of license you get a few options, from which I selected the basic, advanced and lifecycle evaluation licenses. This is the type of license that is required for our demo.
After completing the wizard I can download en implement the license.
Until this point everything goes as it supposed to be.
When i go to the Prime Infrastructure 2.2 appliance (running on VMWare ESXi 5.5.0).
When I go to the license section in Cisco Prime Infrastructure I can implement the license, however if I implement the .lic file I get the error “Unknown feature (PI_VM)”.
I have done implementing license files before, but this is the first time i encounterd this problem.
Who can help me with this error?
Regards,
Dennie VerhoevenHi Dennie,
PI2X-BASE-LF-AS-US-VM-N-EVAL-90 >> I think you have used this product name while generating the license
Either you try generating a new license or contact cisco license team to generate a new license
with the information like below ::
Product Name : R-PI2X-K9
Product Description : R-PI2X-K9:R-PI2X-K9 : Cisco Prime Infrastructure 2.x
Product Qty : 1
UDI : PID: PRIME-NCS-VAPL SN: ANY:ANY
Serial no : with ANY:ANY will work as starting from PI 2.2 , there is no node locking with license.
Thanks-
Afroz
****Ratings Encourages Contributors **** -
Cisco Prime Infrastructure 2.0 and ASA 55xx platform problem
Hello,
We recently upgraded to Prime Infrastructure 2.0 with the hope being able to manage our ASA's from PRIME (and complete an LMS migration).
When I attempt to add ASA's to prime i get the following collection errors:
Unable to collect processor and RAM information. Processor and RAM information. Unexpected error. See the log file inventory.log for details.
In the logfile I get the following XML parsing error on the MIB:
<palError>
<deviceId>6284310032</deviceId>
<code>VALIDATION_ERROR</code>
<message>Failed to validate output XML: cvc-maxInclusive-valid: Value '3484331296' is not facet-valid with respect to maxInclusive '2147483647' for type 'int'.</message>
<result>
<result xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="/CISCO-MEMORY-POOL-MIB/xmp-im-file-system-module.xsd">
<xmp-im-file-system-module>
<MemoryPoolStatistics>
<memoryPoolIndex>1</memoryPoolIndex>
<free>4294967295</free>
<largestFree>4294967295</largestFree>
<used>3484331296</used>
</MemoryPoolStatistics>
To me it seems that the ASA returns a value that is bigger then int32 and thus causes an overflow? Any clues? Workarounds to add an ASA to Prime without checking these MIB'S?
Regards,
MarcelHi,
does anyone happen to know if that problem is fixed? My currently setup looks like this:
1. Cisco Prime Infrastructure 2.1 with updated device pack.
2. Assurance license
3. ASA5510 which has enabled netflow. Netflow is being sent to Cisco Prime 2.1
I do receive netflow raw data within Cisco Prime 2.1 but any graphical display of netflow data is not working. Does anybody has an idea where the problem is? Could it be that the graphical data is only displayed when sending netflow 1, netflow 5 or netflow 7?
regards
Maurus -
Cisco Prime Infrastructure 1.2 OVA - URL/FTP not working
The ESXi install of the theNCS OVA was successful. NCS seems to load and activate interfaces. The console session is working. Using compliant browsers; https://<ip address> does not work. When I stop "ncs" or halt the vm the web page responds shortly but then the connection is lost. I used "show ports" and tried https://<ip address>/8082 and get a login from the Cisco Prime Infrastructure Health Monitor URL. There is a prompt for the authorization key. How can I confirm the installation is complte and all services are up and running
Thanks
TerryAfter digging almost 1 month, I found the answer.
When you do provision from ESXi with ova file, you have to create "Thick Provision" otherwise, you wiil have same problem such as "some services are not up"
In my case, I am running ESXi on the top of VM WorkStation since I don't have any ESXi server. When I added 250GB into the WorkStation and did provision with "Thick" it works !!!
Since my testing envrionment is little complicated (ESXi with VM WorkStation), I added first 250GB HDD into ESXi, and tried. It didn't work. So I added 250GB into VM WorkStation and did provision through Workstation, it worked (If you don't understand this statements, do not worry. If you have ESXi server, you don't need to worry about)
As far as cisco ova is concerned, when I talked to one of my my friend who was working for new ACS (Virtual Appliance) he had same issue. He also solved with "Thick Provision"
FYI, even if when I installed with "Thin Provision", PI 1.2 used only 10GB out of 200GB, so I did not think that I should use "Think Provision". But definitely not. -
Can't import images in cisco prime infrastructure 1.2
- Any job , trying to import images, in my cisco prime infrastructure fails with :
Jan 14 13:14:53 cisco-prime 01/14/13 13:15:18.040 ERROR [service] [pool-4-thread-19] IFM_SWIM_EXCEPTION: [com.cisco.ifm.swim.service.exception.IfmSwimParserException: Cannot populate software image info object from the image.]
How I can I solve this one ?
Tx,
M.I seem to have the same problem, strangely enough importing a universal image for 2960s worked fine, but I get thos error when trying to import a 3750x image
-
Cisco Prime Infrastructure 2.0 and Cisco ASA
Hello,
We've recently installed trial version of Cisco Prime Infrastructure 2.0 Express. We hoped that it already supports Cisco ASA 55xx series (especially 5505, we have pretty amount of them). But we had some problems with PI and asa durind the exploitation process.
First, I've added ASA to PI, and Inventory Collection Status is Completed, but I can't see CPU and RAM utilization graphs. Inventory.logs are non-informative.
Also, config backup is success, but when I try to watch the backuped configuration at Configuration Archive PI says "Failed to fetch raw configuration". And so on.
ASA version is 5505, image is 9.1(2).
So, I have a question: is it possible to manage ASAs with PI 2.0?
UPD: I've just tried to upgrade asa to 9.1(4), and behavior of the equipment is quite the same. Seems we shall wait for 9.2 to be released.Have you downloaded and applied the latest Device Pack updates?
PI enhanced ASA support after the initial 2.0 release and the Device Packs incorporate that change.
The README file for Device Packs explains how to install them. (A bug currently does not allow the direct download in PI so you need to follow the method for installation from local storage after you manually download. Here is a link to the download location. -
Cisco Prime Infrastructure 1.2 on Windows Server/Hyper-V
Hi Everyone,
In Entriprise environment while designing a BYOD solution we need to integrate ISE3315 with CPI 1.2. I know that Cisco ISE software either runs on 3315 platform or other option is virtual appliance (which is VMware based). Now problem is that we have Hyper-V environment as standard so I need to go with ISE-3315. Here my concern is to I install CPI 1.2 on Hyper-V, or on a Windows Server (2008 or 2012) based machine. Is that doable?
Any help, suggessions would be warmly welcomed.
Thanks,
Azhar...Cisco Prime LMS will slowly be phased out in favor of Cisco Prime Infrastructure and hence there are no new mainline releases are planned to provide support to new Hardware or virtualization support.
However, Prime LMS do support Hyper V Virtualization (As an installable in Windows 2008). Please note that Virtualization technologies like, VMWare and Hyper V virtualization systems are not supported in LMS 5000, and LMS 10000 Devices license, in Windows. VMWare Systems are supported in LMS 5000, and LMS 10000 Devices license in Soft Appliance. Virtualization technologies like, VMWare and Hyper V virtualization systems are not supported in LMS 5000, and LMS 10000 Devices license, in Windows. VMWare Systems are supported in LMS 5000, and LMS 10000 Devices license in Soft Appliance.
For more details on HW and SW requirements for Cisco Prime LMS, please check document here.
-Thanks
Vinod -
Cisco Prime Infrastructure 2.0 - no traps/info are pushed from devices
Good evening,
I have setup Cisco Prime Infrastructure 2.0 and, though I have added manually my 4 network cores as devices without any problem, I can't get a single trap or a single SNMP information to be pushed into my Cisco Prime Infra.
Here is my SNMP config on my core :
snmp-server user *edited* *edited* v3
snmp-server group *edited* v3 noauth notify *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF0F
snmp-server community *edited* RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps rf
snmp-server enable traps memory
snmp-server enable traps cpu_threshold
snmp-server enable traps eigrp
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps flex-links status
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps ether-oam
snmp-server enable traps aaa_server
snmp-server enable traps flash insertion removal
snmp-server enable traps l2tc threshold sys-threshold
snmp-server enable traps power-ethernet police
snmp-server enable traps rep
snmp-server enable traps vswitch dual-active vsl
snmp-server enable traps udld link-fail-rpt status-change
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps auth-framework sec-violation
snmp-server enable traps dot1x auth-fail-vlan guest-vlan no-auth-fail-vlan no-guest-vlan
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps entity-diag boot-up-fail hm-test-recover hm-thresh-reached scheduled-test-fail
snmp-server enable traps port-security
snmp-server enable traps ethernet evc status create delete
snmp-server enable traps energywise
snmp-server enable traps ipsla
snmp-server enable traps vstack
snmp-server enable traps bfd
snmp-server enable traps bgp
snmp-server enable traps bulkstat collection transfer
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps isis
snmp-server enable traps msdp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps errdisable
snmp-server enable traps ethernet cfm alarm
snmp-server enable traps vlan-membership
snmp-server enable traps mac-notification change move threshold
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *ip-address-edited* version 3 noauth *edited*
Basically all traps are enabled but absolutely nothing is showing up in my Prime Infra except that my 4 devices are "Reachable".
Here is a show snmp on the same device :
sh snmp
Chassis: *S/N Edited*
38554534 SNMP packets input
0 Bad SNMP version errors
14 Unknown community name
0 Illegal operation for community name supplied
0 Encoding errors
38453185 Number of requested variables
0 Number of altered variables
17790703 Get-request PDUs
20583581 Get-next PDUs
0 Set-request PDUs
0 Input queue packet drops (Maximum queue size 1000)
38490708 SNMP packets output
0 Too big errors (Maximum packet size 1500)
0 No such name errors
0 Bad values errors
0 General errors
38371069 Response PDUs
13 Trap PDUs
SNMP global trap: enabled
SNMP agent enabled
SNMP logging: enabled
Logging to *edited*, 0/10, 13 sent, 0 dropped.
Can anyone point out what is wrong or missing in my configuration? I can't seem to single it out myself.
Thanks
JeremyHi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors **** -
Cisco Prime Infrastructure patch 2.1.1 - HA issue
Hello,
I have a problem with the Cisco Prime Infrastructure patched to version 2.1.1. I did exactly what Installation Guidelines say:
http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-1-1/release/notes/cpi_rn.html
– Install the Prime Infrastructure 2.1.1 patch by using the Administration > Software Updates page on the primary server.
– Restart the primary server.
– Verify that the patch installation is complete. If you find the installation complete, decommission and reinstall the secondary server and add it back to the primary server.
I reinstalled HA server and I'm trying to add it to HA but I get "Failed to authenticate - Primary(xx.xx.xx.xx) and Secondary(xx.xx.xx.xy) PI version does not match"
Can you help me with that? What I'm doing wrong? or maybe this patch is not prepared to work in HA mode?
RegardsSymptom:
The installation instructions of PI 2.1.1 patch in a High Availability environment are not accurate and following these steps will result in the inability to re-pair the Primary and Secondary servers.
Conditions:
If the instructions are followed, then when the user attempts to re-pair the servers, an error will be encountered:
"High Availability Registration Failed - Failed to authenticate - Primary (x.x.x.1) and Secondary (x.x.x.2) PI version does not match".
Instead, the following steps have proved to work correctly:
1. Upload and install patch on primary.
2. Upload and install patch on secondary.
3. Stop NCS services on secondary
4. Stop NCS services on primary
5. Start services on secondary
6. Start services on primary
7. Re-pair HA servers from primary
Workaround:
Workaround 1:
On the secondary, go under root and issue:
# cd /opt/CSCOlumos/bin/
# ./hamode.sh primary
Answer 'yes' when prompted.
Go to admin user and execute
# ncs stop
After the services are stopped:
# ncs start
When the services are back up, login to the secondary GUI as you would login to a primary server
Go under Administration > Software update, upload the patch and install it.
Go to admin user and execute
# ncs stop
After the services are stopped:
# ncs start
When the services are up, go under root and issue:
# cd /opt/CSCOlumos/bin/
# ./hamode.sh secondary
Answer 'yes' when prompted.
Go to admin user and execute
# ncs stop
After the services are stopped:
# ncs start
After the message that services started successfully on the secondary, initiate a new High Availability configuration from the primary. Now the synchronization between the two servers should succeed.
Workaround 2:
Redeploy or reinstall the Primary server, restore the backup which was taken prior to applying the patch, reconfigure the High Availability and continue with the steps described in the Conditions section.
Further Problem Description:
Release Notes have been updated with more precise instructions.
Known Affected Releases:
(1)
2.1(0.0.85) -
Cisco Prime Infrastructure 1.2
Hello,
I have some maps of our building in PDF format and i want to load them on the cisco prime infrastructure 1.2, could you tell me how?
FYI: i opened : Design tab => Site maps Design but after this i don't know if i have to create a group or no;
ThanksThanks, i done it.
I have a problem to fill out some information in the New Floor Area tab:
our building has 1 basement and a ground floor and 3 floors, may I consider the ground floor as a the first floor because i have to fill out Number of floors on the edit building tab then i have to put 4 floors otherwise in the new floor area i'll have only 3 floors on the drop down list. (and the last floor will not has an id floor)
and the problem is
ground floor has floor id 1
1st floor has floor id 2 ......
have you any suggestion? -
Cisco Prime Infrastructure 1.2 - web browser freezes when managing rogue APs alarms
Hello all,
has anybody faced a freezing problem when you click in Cisco Prime Infrastructure 1.2 down on alarm bar and then to Rogue AP alarms and then try to add an annotitation or change a rogue alarm to Friendly?
I tried it on different PC, different browsers (Firefox 14.0.1. Chrome ...) and the problem is still there.
Has anybody an idea?
Thanks.
Regards
KarelI just tried it from my lab VM and had no problems. I use Chrome and the browser does sometimes not refresh for a while but that is just when I start to click around.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
Cisco Prime Infrastructure 1.2 - Remote FTPrepository Sizing Guide
Can anyone provide a link to a sizing guide for remote FTP repository for backing up Cisco Prime Infrastructure 1.2 to a remote FTP server?
A personal observation; In PI 1.1, with the small ova we were running around 300 AP's and I had noticable slowness and issues. At that time, TAC mentioned that I should go with the medium as it was a known problem Now, despite being on 1.2 and alot of the issues resolved (and now new ones), if faced with the need to start over and I could spare the hardware, I would still go with the medium. My personal opinion is that Cisco VM's require way to much. On the other hand, knowing that it's relying on a built in Oracle DB, which from my experience with virtual servers, databases in VM = bad, it's understandable. Not everyone agrees with this point from vm gurus to db geniuses, and I'm not a professional vm guy, just play one on tv, but personally i shove as much hardware as I can afford from my host at it if it's a db in a vm. This comes from being in an enterprise with multiple oracle db's in multiple vm environments. My 2cents.
-
Cisco Prime Infrastructure and no new events / alarms since update to 2.2.1
Hello,
I have upgraded our Cisco Prime Infrastructure from version 2.1 to 2.2.1 (with a backup and restore). We have round about 700 APs and three 5208 Controller. So far everything seems to work really fine. The only problem is that there are no new alarms/events under "Monitor", "Alarms and Events".
The last entries (events and alarms) are dated before the upgrade. Other informations (like client counts for example) are correct.
Is there a known bug related to my problem? Can anybody help?
ThanksI have done some research:
I see the following problems in the log-package (downloaded from Prime):
===
<msg time='2015-04-07T12:10:50.620+02:00' org_id='oracle' comp_id='rdbms'
client_id='' type='UNKNOWN' level='16'
host_id='rzprime' host_addr='xxx.xxx.xxx.xxx' module='JDBC Thin Client'
pid='9499'>
<txt>ORA-1652: unable to extend temp segment by 128 in tablespace TS_EVENTS
</txt>
</msg>
<msg time='2015-04-07T12:10:50.727+02:00' org_id='oracle' comp_id='rdbms'
client_id='' type='UNKNOWN' level='16'
host_id='rzprime' host_addr='xxx.xxx.xxx.xxx' module='JDBC Thin Client'
pid='15177'>
<txt>ORA-1652: unable to extend temp segment by 128 in tablespace TS_EVENTS
</txt>
</msg>
===
I think that there is a problem with a too small tablespace. But I can´t fix that. Anybody? ;) -
Cannot add WLC 5508 7.2.111.3 to Cisco Prime Infrastructure 2.0
Though the Cisco Prime Infrastructure Compatibility Matrix list out that 7.2.111.3 is supported for PI 2.0
I am not able to add the controller to the PI 2.0.
The Reachability Status always shown "Unknow" and SNMP Status always shown "No response for SNMP Get".
There is no firewall between the WLC and PI.
And ping test shows it is reachable.
If I try to add controller by non-management port (I know it is not work but I want to try the reachability), the Reachability Status shown "Reachable" but the SNMP Status always shown error.
And if I use some SNMP testing software to test the SNMP port. SNMP can be quoted.
I have try to lower down the "Maximum VarBinds per Get PDU" but no luck.
Any thing I can do to troubleshoot the problem?Yes, I follow the procedure but it does not work.
Another update:
I add another WLC with version 7.0.98.0. It is fine.
And I setup another new PI 2.0 and new temporary WLC5508 with 7.2.111.3 to test. It work fine also......
So, I am wondering the existing 7.2 WLC have problem in responsing the SNMP Get. But I dont have any idea to test....
Do anyone have idea to test the snmp connection between PI and WLC?
Maybe you are looking for
-
Table Maintenance - Field Names not appearing
Hi, I given table maintenace for 'Z' table. When i went to SM30 transcation, the fields which are taken as Built-in type instead of Data elements are not having caption( Field names ) . It is showing '+' in the place of Fieldname . What may
-
Deployed in Kuwait - VPNclient configuring w/o networkmanager (pptp)
My laptop connects to a wireless router in the barracks and Kuwait has quite a few filters on what we can access. I've purchased an account with an online VPN provider and have been able to connect via windows7 and via networkmanager-pptp in Arch. Th
-
String.matches vs Pattern and Matcher object
Hi, I was trying to match some regex using String.matches but for me it is not working (probably I am not using it the way it should be used). Here is a simple example: /* This does not work */ String patternStr = "a"; String inputStr = "abc"; if(inp
-
I am trying with this cade. when I m using ResourceContext, the passed parameter IUser deprecation problem comes... How can I solve it ?? Which ResourceContext class I should use? or any alternative ?? Please help me to write simple application to re
-
Hi, I have installed Adobe Reade X on my machine. For an application I need to use DDE. For previous versions of Adobe Reader, the DDE SERVER Name = "Acroview" worked fine. But for this particular version DDE Server name name is AcroviewR10. Is there