Cisco Prime Infrastructure 1.4 SNMP Traps are not converted into Alarms
Hi everybody,
I just configured SNMP Traps on a Cisco Catalyst 3750-x to send to our Cisco Prime Infrastructure 1.4 Appliance.
Now I forced the Switch to send some traps (Power off a Power Supply, Interface errdisable). The only events I see in Alarms & Events on PI is the same information message everytime:
Configuration management event has been recorded in ccmHistoryEventTable.
I think the forced traps should be converted into alarms? Why can't I see them?
Thanks,
Marc
Ok, I started debugging as you said. I get the following output:
Mar 13 09:28:13.711: SNMP: V2 Trap, reqid 11689, errstat 0, erridx 0
sysUpTime.0 = 198609846
snmpTrapOID.0 = ciscoSyslogMIB.2.0.1
clogHistoryEntry.2.1688 = PM
clogHistoryEntry.3.1688 = 5
clogHistoryEntry.4.1688 = ERR_RECOVER
clogHistoryEntry.5.1688 = Attempting to recover from bpduguard err-disable state on Gi1/0/13
clogHistoryEntry.6.1688 = 198609844
Mar 13 09:28:13.737: SNMP: Queuing packet to xx.xx.xx.xx
Looks like the Switch is sending SNMP Traps from the ciscoSyslogMIB. Is this why PI can't show the Traps and convert it into a alarm?
After this test I configured logging (syslog) to the PI. Now the errors are showed but still not converted into alarms. I just want to be notified by email when such errors occurs.
Thanks,
Marc
Similar Messages
-
Cisco Prime Infrastructure 2.0 - no traps/info are pushed from devices
Good evening,
I have setup Cisco Prime Infrastructure 2.0 and, though I have added manually my 4 network cores as devices without any problem, I can't get a single trap or a single SNMP information to be pushed into my Cisco Prime Infra.
Here is my SNMP config on my core :
snmp-server user *edited* *edited* v3
snmp-server group *edited* v3 noauth notify *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF0F
snmp-server community *edited* RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps rf
snmp-server enable traps memory
snmp-server enable traps cpu_threshold
snmp-server enable traps eigrp
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps flex-links status
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps ether-oam
snmp-server enable traps aaa_server
snmp-server enable traps flash insertion removal
snmp-server enable traps l2tc threshold sys-threshold
snmp-server enable traps power-ethernet police
snmp-server enable traps rep
snmp-server enable traps vswitch dual-active vsl
snmp-server enable traps udld link-fail-rpt status-change
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps auth-framework sec-violation
snmp-server enable traps dot1x auth-fail-vlan guest-vlan no-auth-fail-vlan no-guest-vlan
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps entity-diag boot-up-fail hm-test-recover hm-thresh-reached scheduled-test-fail
snmp-server enable traps port-security
snmp-server enable traps ethernet evc status create delete
snmp-server enable traps energywise
snmp-server enable traps ipsla
snmp-server enable traps vstack
snmp-server enable traps bfd
snmp-server enable traps bgp
snmp-server enable traps bulkstat collection transfer
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps isis
snmp-server enable traps msdp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps errdisable
snmp-server enable traps ethernet cfm alarm
snmp-server enable traps vlan-membership
snmp-server enable traps mac-notification change move threshold
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *ip-address-edited* version 3 noauth *edited*
Basically all traps are enabled but absolutely nothing is showing up in my Prime Infra except that my 4 devices are "Reachable".
Here is a show snmp on the same device :
sh snmp
Chassis: *S/N Edited*
38554534 SNMP packets input
0 Bad SNMP version errors
14 Unknown community name
0 Illegal operation for community name supplied
0 Encoding errors
38453185 Number of requested variables
0 Number of altered variables
17790703 Get-request PDUs
20583581 Get-next PDUs
0 Set-request PDUs
0 Input queue packet drops (Maximum queue size 1000)
38490708 SNMP packets output
0 Too big errors (Maximum packet size 1500)
0 No such name errors
0 Bad values errors
0 General errors
38371069 Response PDUs
13 Trap PDUs
SNMP global trap: enabled
SNMP agent enabled
SNMP logging: enabled
Logging to *edited*, 0/10, 13 sent, 0 dropped.
Can anyone point out what is wrong or missing in my configuration? I can't seem to single it out myself.
Thanks
JeremyHi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors **** -
Cisco Prime Infrastructure 1.3 - TFTP backup WLC not working
I don;t get the the background task "Controller Configuration Backup" working. I want to use default TFTP.
When i look in the logging i see 2 of three WLC's succesfully backuped there logging. Is their a log file where you can see what is happening?
With kind regards,
Martijn.Hi Martijn:
If you go to the controller's GUI to Commands > Upload File and manually trigger the TFTP Configuration backup, does the process complete as expected? If not, whatever's causing that problem needs to be addressed first.
When someone wants to do a config backup from the command line, they give a series of commands
transfer download datatype config
transfer download mode tftp
transfer download serverip x.x.x.x
transfer download path ./
transfer download filename myBackup.cfg
transfer download start
The Controller Config Backup background task is just the SNMP version of "transfer download filename " and "transfer download start". If these other required settings aren't already there, the task isn't going to set them (the humans have to). If there's a problem with writing out the file on the server, or packet routing issues to get to the server, the task isn't going to see those things, it just knows that the answer to "transfer download start" wasn't "Okay!"
As for watching this processing in logs, go to Administration > Logging, and set the logging level to Trace for the modules SNMP and System, and click Save. Then kick off your backup attempt, allowing it to fail. When it does, return to Administration > Logging, and click the Download button to retrieve the logs.zip file. The activity should be in the ncs-x-x.log file.
If you don't have the new Update-1 patch for Prime Infrastructure 1.3.0.20 (filename PI_1.3.0.20_Update_1-12.tar.gz) installed, I'd suggest you get it. While it's not going to specifically address this issue, there are a lot of really good fixes in it.
Release Notes for Update 1 for Cisco Prime Infrastructure 1.3.0.20 -
Cisco Prime Infrastructure 1.2 OVA - URL/FTP not working
The ESXi install of the theNCS OVA was successful. NCS seems to load and activate interfaces. The console session is working. Using compliant browsers; https://<ip address> does not work. When I stop "ncs" or halt the vm the web page responds shortly but then the connection is lost. I used "show ports" and tried https://<ip address>/8082 and get a login from the Cisco Prime Infrastructure Health Monitor URL. There is a prompt for the authorization key. How can I confirm the installation is complte and all services are up and running
Thanks
TerryAfter digging almost 1 month, I found the answer.
When you do provision from ESXi with ova file, you have to create "Thick Provision" otherwise, you wiil have same problem such as "some services are not up"
In my case, I am running ESXi on the top of VM WorkStation since I don't have any ESXi server. When I added 250GB into the WorkStation and did provision with "Thick" it works !!!
Since my testing envrionment is little complicated (ESXi with VM WorkStation), I added first 250GB HDD into ESXi, and tried. It didn't work. So I added 250GB into VM WorkStation and did provision through Workstation, it worked (If you don't understand this statements, do not worry. If you have ESXi server, you don't need to worry about)
As far as cisco ova is concerned, when I talked to one of my my friend who was working for new ACS (Virtual Appliance) he had same issue. He also solved with "Thick Provision"
FYI, even if when I installed with "Thin Provision", PI 1.2 used only 10GB out of 200GB, so I did not think that I should use "Think Provision". But definitely not. -
Cisco Prime Infrastructure 2.1: SNMP Connectivity Failed
Hi,
I have discharged all my Cisco devices within Cisco Prime and after a few days and when everything worked correctly one of the switches is displayed with the SNMP error Connectivity Failed, nothing has been changed.
I deleted and i have returned to create the object but it continues to be the same, I've also tried to create another SNMP community still receiving the same error.
This is the configuration of snmp in the switch WS-C3850-48P with version 03.02.02.SE
snmp-server community "community" RW
snmp-server location "location"
snmp-server contact "contact"
snmp-server host 10.180.5.22 version 2c "community"
Best regards.Hi ,
check if you are getting these errors in "show log" again:
%SNMP-3-INPUT_QFULL_ERR: Packet dropped due to input queue full
If yes , then either a lot of SNMP polling happening on the device
or
CPU utilization is going high sometime , being SNMP as a least priority process , you will see this issue. check for "show proc cpu history"
It is a device side issue definitely.
I would suggest to apply a Access-list on the SNMP community string allowing only the
valid NMS to poll the device
Thanks-
Afroz
***Ratings Encourages Contributors *** -
Planned orders are not converted into process orders in ECC.
Dear All,
The issue is that Planned orders with conversion tick are not publishing in ECC as manufacturing orders. We did check the relevant master data consistency between APO and ECC and it seems fine.
We have tried to send the conversion from APO to ECC,all the orders stuck in the R1P inbound queue with error - Order no. XXXX does not exist
Message no. C/006.
Based on above message and error we found SAP Note 515740 - Inconsistencies in table CIFORDMAP for this issue.
Used the transaction SE38 and created RCFORDCH report and 'Checking inconsistencies in table CIFORDMAP'
Here it shows order series stuck in queues no longer exists.
But not sure how to reconcile the inconsistency in the CIFORDMAP table.
Would appreciate your advice.
Regards,
Sajit SInghHi Sajit Singh,
Could you take some sample items struck for order conversion and check
whether active PPDS & SNP PPMs available.
In some cases, conversion will be affected for want of PPMs. If it is the
case with you, try generating the PPM first for that sample item and retry
converting the orders.
Could you please check and confirm this.
Regards
R. Senthil Mareeswaran. -
Consultations on Cisco Prime Infrastructure 2.2
I recently installed Cisco Prime Infrastructure 2.2 and I have 2 questions regarding configuration:
1. What configurations should run for vulnerability when some event occurs on a switch an alarm is lifted in the Cisco Prime Infrastructure 2.2?
2. Is there any way to put a device into maintenance mode in the web interface of Cisco Prime Infrastructure 2.2, so that can not be spoiled reports regarding equipment availability during the execution of maintenance?1. If you configure PI as an SNMP and syslog server for your devices and have enabled logging traps etc., PI's alarm browser will show the alarms. If you want them to be sent to you via email, you can do that under the Admin menu for setting up your Mail server and clicking the link to "Configure email notification for individual alarm categories." (see below - open in new tab to zoom). It's not completely customizable but what you see there is the current product capabilities in that regard.
2. No, this is not currently an available feature in PI 2.2. -
Trouble With Cisco Prime Infrastructure 1.3
Hi,
I have installed the Evaluation Version Cisco Prime Infrastructure 1.3.
There are a few problems that i am facing;
I am trying to push a simple configuration to WLC using Prime Infrastructure. But it is failing as PI doesnot have RW SNMP access.
My question is that can I use PI to push configs without using SNMP. Like do it using ftp or something.
Also do the Wired Devices also need SNMP RW access on PI's part.
2. I tried running discovery for WLC and it worked fine where all the controllers were discovered. But when I try to discover a Switch, the reachability tab says Reachable but in Collection Status tab it shows Unmanaged. When I click on the Unmanaged tab it says " Pre-collection check failed because: ". I have configured the SNMP correctly.
3. I have the CAD files for all the maps in our environment but when I try to upload it to Prime it converts it into GIF, so the maps are uploaded as plain image with no knowledge of walls and obstacles.
So we would have to add the walls and obstacles by ourselves. Is there any way it can automatically pick up on the walls and obstacles and thus provide a better way for predicting RF profiles.
All your help is greatly appreciated.TAC Case! Sounds like a bug to me...
Sent from Cisco Technical Support iPad App -
What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP's?
What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP’s?
• PI provides visibility for autonomous clients within the same list view as lightweight and wired clients (client list page).
• Rogue AP detection for autonomous AP's is not supported (it's supported in CUWN).
• Alarms/events for client authentication issues (e.g. authentication failure) are displayed in PI.
• Config management for autonomous AP's is via CLI template. Config comparison and archiving functionality in PI leverages these same features that were brought in from LMS, so need to defer to others in terms of whether this is a cross-platform feature in PI or is only supported on a subset of platforms. Config comparison/archive is supported in CUWN.PI supports both infrastructure (e.g. AP Tx Power and Channel, busiest AP, AP utilization, etc.) and client (e.g. client count, client sessions, etc.) reports, and there are extensive reports for CUWN -
Hi,
I have a Cisco Prime Infrastructure 1.3 deployment with Catalyst 2960S switches. Switches are running IOS 15.0(2) SE2. All switches have SNMPv2 configured, and all appears to be fine. I'm migrating one switch to SNMPv3, and PI have reachability to the switch, but PI doesn´t receive traps from the switch, and neither poll CPU and memory information (all displays 0.00%).
Somebody have a sample configuration of SNMPv3 with Cisco Prime (Infrastructure or LMS)? I cannot find a Cisco official (or unofficial) document related to this version, usually all mention SNMPv2.
Thank you.
EduardoHi Eduardo:
SNMPv3 is indeed supported for general administration. There's a bug with SWIM using SNMPv3 (CSCud92758), but you should be fine for just monitoring. Have you deleted the switch, waited until Prime Infrastructure told you it was gone, then readded it as SNMPv3 natively? Bug CSCug78869 keeps things from working well when changing SNMP versions.
If you don't have the new Update-1 patch for Prime Infrastructure 1.3.0.20 installed (filename PI_1.3.0.20_Update_1-12.tar.gz) installed, I'd suggest you get it. While it's not going to specifically address this issue, there are a lot of really good fixes in it.
Release Notes for Update 1 for Cisco Prime Infrastructure 1.3.0.20 -
Cisco Prime Infrastructure, trial version
I am trying the Cisco Prime Infrastructure, trial version.
In client management I can see only 802.3 clients, but not clients directly attached to the switch ports.
Finding where a client, searched by IP or MAC address, is connected, is a mandatory need for us.
I have enabled trap sending from the switches.
Regards
Donato Colombo- Please make sure that your switches are defined (added) in Prime, especially matching the
correct SNMP READ community (as it was defined on the switch).
M. -
Cisco Prime infrastructure template undeploy
Hi,
I am new to cisco prime, I have create the new Trap receiver template and deployed to one of the wireless controller and saved the deployment
Now I want to undeploy the templates, When I tried undeploying the templates for same wireless controller, I got the warning message stating "Failed to undeploy the template"
Please advice on below points
1. How to undeploy the templates in cisco prime infrastructure
2. Where to find the snmp traps ( steps to check the snmp traps) in cisco prime.
Please Help!!!!!Using System Logs
Prime Infrastructure logs all error, informational, and trace messages generated by all devices that are managed by Prime Infrastructure.
Prime Infrastructure also logs all SNMP messages and Syslogs it receives.
You can download and email the logs to use for troubleshooting Prime Infrastructure.
Step 1 Choose Administration > Logging. The General Logging Options Screen appears.
Step 2 Choose a Message Level.
Step 3 Check the check boxes within the Enable Log Module option to enable various administration modules. Check the Log Modules option to select all modules.
Step 4 In the Log File Settings portion, enter the following settings. These settings will be effective after restarting Prime Infrastructure.
Note The log file prefix can include the characters "%g" to sequentially number of files.
Step 5 Click the Download button to download the log file to your local machine.
Note The logs.zip filename includes a prefix with the host name, date, and time so that you can easily identify the stored log file. Included in the zip file is an html file that documents the log files.
Step 6 Enter the Email ID or Email IDs separated by commas to send the log file.
Note To send the log file in a mail you must have Email Server Configured.
Step 7 Click Submit. -
Cisco Prime Infrastructure 2.0 - Third Party NetFlow
Hi,
is it possible to collect on the Cisco Prime Infrastructure 2.0 NetFlows from Third Party Devices, like a SonicWALL Firewall?
I mean it is possible to poll SNMP informations from a third party device, so maybe it is also possible to get the NetFlow from this Device?
Best Regards,
Sven K.
Sent from Cisco Technical Support iPad AppHi Sven,
As per my understanding for 3rd party Only below thing are supported:
The following support level is available with Prime Infrastructure :
• Auto Discovery of a 3rd party Device
• Basic Inventory collection
• Basic lifecycle management of 3rd party device
• Ability to show traps and syslog for 3rd party devices
• Device reachability status polling
• Ability to load new MIBs & to create new monitoring templates
• For both Cisco and any SNMP device
More info is available in the link given below:
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/1.2/release/notes/cpi_rn.html#wp75765
Thanks-
Afroz
[Do rate the useful post] -
UPS monitoring support with Cisco Prime Infrastructure 1.2
Dear Members,
Good day,
I am having a project implemented wherein i have the UPS power redudancy solution for our network devices.
Now can anyone gide that is it possible for below :-
UPS units installed with SNMP cards be monitored via Cisco Prime Infrastructure 1.2 as our monitoring & management solution is Cisco Prime Infrastructure 1.2 ?
if yes
Can you guide if following action would be possible to export the below logs from UPS unit to our Cisco Prime Infrastructure 1.2
a) UPS fault status information
b) UPS operational status(input power available Y/N)
c) Battery fault status
d) Battery charging current
e) Battery charge level
f) Output current
Conclusion is we need to confirm that would it be posible to achieve remote monitoring of these UPS units via our CPI 1.2
Thanks in Advance for your support & replies to this query.
Regards,
Muzammil N.Prime Infrastructure 1.2 can manage non-Cisco devices in a limited fashion via SNMP query and trap processing. It cannot import logs and does not have a generic syslog server,
So if your devices have snmp read only support and can generate SNMP traps for the above you can add them to PI. Follow the manual add device procedure here. -
Ask the Expert: Cisco Prime Infrastructure - Implementation and Deployment
Welcome to the Cisco Support Community Ask the Expert conversation.
This Ask The expert Session will cover questions spanning Cisco Prime Infrastructure on Implementation and Deployment on Wired and Wireless. This will be more specific to Customer’s and Partners questions product covering PI on configuration, Features and Menu, Network Monitoring, Maps, Implementation, High Availability and Maintenance and t/s parts.
Monday, February 2nd, 2015 to Friday, February 13th, 2015
Dhiresh Yadav is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco Prime Infrastructure and Cisco Wireless products. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS) and CCIE (DC) certifications.
Afroz Ahmad is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS),CCIE (DC), and SCJP (Sun Certified Java Professional )
Vinod Kumar Arya is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 8 years of industry experience working with large enterprise and service provider networks. He also holds VCP 5 and RHCE certifications.
** Remember to use the rating system to let the experts know you have received an adequate response.**
Because of the volume expected during this event, the experts might not be able to answer every question. Remember that you can continue the conversation in the Network Infrastructure community, > Network Management, shortly after the event. This event lasts through February 13th 2015. Visit this forum often to view responses to your questions and those of other Cisco Support Community members.Hello Wilson,
Thanks for joining us.
1841 should just work fine for net flow . Hope you have a valid "PI Assurance license" installed on the server.
"PI Assurance license" is required for "net-flow" feature
Devices supporting Netflow in PI ::
1400, 1600, 1700 & 1800
2500, 2600 & 2800
3600, 3700, 3750 & 3800
4500 & 4700
AS5300 & 5800
7200, 7300, 7400 & 7500
Catalyst 4500 ASCI
Catalyst 5000, 6500, & 7600 ASCI
ESR 10000 ASCI
GSR 12000 ASCI
Cisco IOS Software Release Version
Supported Cisco Hardware Platforms
11.1CA, 11.1CC
Cisco 7200 and 7500 series, RSP 7200 series
12.0
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series
12.0T, 12.0S
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8600 series
12.0(3)T, 12.0(3)S
Cisco 1720, 2600, 3600, 4500, 4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)T
Cisco 1400, 1600, 1720, 2500, 2600, 3600, 4500,
4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)XE
Cisco 7100 series
12.0(6)S
Cisco 12000 series
NetFlow is also supported by these devices Cisco 800, 1700, 1800, 2800, 3800, 6500, 7300, 7600, 10000, CRS-1 and these Catalyst series switches: 45xx, 55xx, 6xxx.
NetFlow export is also supported on other Cisco switches when using a NetFlow Feature Card (NFFC) or NFFC II and the Route Switch Module (RSM), or Route Switch Feature Card (RSFC). However, check whether version 5 is supported, as most switches export version 7 by default.
You can check the below steps to diagnose the issue::
To verify that NetFlow is exported from a device to PI, follow the steps below:
1) Browse to Administration > Data Sources page. Check the value in column ‘Last Active Time’ for the ‘Device Data Sources’ table. If the table is empty or the value does not represent recent time, then
it is possible that the device is not exporting NetFlow or PI Assurance license is not applied / expired.
2) Login to PI console ( via SSH) as root user and run the command:
netstat –an | grep 9991 – Output of this should be like : udp 0 0 :::9991 :::*
Check the firewall settings on PI server using the command: firewall -L
1) Check the configuration on an IOS / IOS –XE device. Run the commands
a) sh running-config | inc destination
1) This should list the IP address of the PI SERVER ( along with other outputs if any)
b) sh running-config | inc 9991
1) This should list at least one entry.
c) If the above are fine, then verify that the flow monitor, flow exporter and the flow records are correctly configured on the device.
Refer to the URLs below to configure NetFlow export.
http://preview.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/user/guide/setup_monitor.html#wp1056427
Thanks-
Afroz
***Ratings Encourages Contributors ****
Maybe you are looking for
-
EMail Link in SWF exported from InD CS5 does not work
I'm trying to find a definitive answer on this. I have designed an interactive document in InD CS5 that has buttons and hyperlinks. When exported to SWF everything works except my e-mail hyperlink. It works fine in InDesign's preview pane. I've uploa
-
Do you have to pay for a refurbished iPad if your iPad is still has warranty ?
Do you have to pay for a refurbished iPad if your iPad is still has warranty ? Or something like that ?
-
Hi, I am using the C++ interface that is provided with Oracle 9i. The way to do it according to the examples is to first create an instance of an Environment object, create a connection and then create Statement(s) to execute the SQL. What I am tryin
-
Our group has a small lab (networking, servers, other odds and ends) as well as a small equipment closet with general test gear (network analysis, spectrum analyzer, some installation gear, etc.). Unfortunatley items frequently go missing, either so
-
Impdp - duplicate keys found error
I'm facing a strange issue. I'm running expdp / impdp using datapump. The export of the schema is successful. The import of the schema is raising the below errors for few PKs. I have verified on the source database. There are no duplicate records fou